PLUMBING RE-SUBMITTAL 22 11 17 ACADEMIC BUILDING & PATRIOT S CASA TEXAS A&M UNIVERSITY - SAN ANTONIO, TX NO. 25-3122, VAC NO. 39019 OWNER: ARCHITECT: MEP ENGINEER: GENERAL CONTRACTOR: PLUMBING CONTRACTOR: THE TEXAS A&M UNIVERSITY SYSTEM KELL MUNOZ ARCHITECTS, INC. 1017 N. MAIN AVENUE, SUITE 300 SAN ANTONIO, TEXAS 78212 PHONE: 210-349-1163 SHAH SMITH & ASSOCIATES, INC. 2825 WILCREST DR. SUITE 350 HOUSTON, TX 77042 PHONE: 713-780-7563 BARTLETT COCKE 8706 LOCKWAY SAN ANTONIO, TX 78217 PHONE: 210-655-1031 VICTORIA AIR CONDITIOING, LTD 513 PROFIT DRIVE VICTORIA, TEXAS 77901 PHONE: 361-578-5241 (212)
PLUMBING RE-SUBMITTAL 22 11 17 ACADEMIC BUILDING & PATRIOT S CASA TEXAS A&M UNIVERSITY - SAN ANTONIO, TX NO. 25-3122, VAC NO. 39019 TABLE OF CONTENTS SPEC # ITEM VENDOR 22 11 17 GAS PIPING AND APPURTENANCES AMERIPIPE/MORRISON
PLUMBING RE-SUBMITTAL 22 11 17 ACADEMIC BUILDING & PATRIOT S CASA TEXAS A&M UNIVERSITY - SAN ANTONIO, TX NO. 25-3122, VAC NO. 39019 LIST OF SUPPLIERS/SUBCONTRACTORS AMERIPIPE SUPPLY 4354 INDUSTRIAL CENTER #110 SAN ANTONIO, TX 78217 POC: BART KUNKEL PHONE: 210-655-4900 EMAIL: brkunkel@ameripipe.com MORRISON SUPPLY CO 10130 JONESMALTSBERGER RD SAN ANTONIO, TX 78216 POC: STEVE TSCHIRHART PHONE: 210-344-4436 EMAIL: sjtschirhart@morsco.com
ACADEMIC BUILDING & PATRIOT S CASA TEXAS A&M UNIVERSITY - SAN ANTONIO, TX NO. 25-3122 PLUMBING RE-SUBMITTAL SPECIFICATION SECTION SECTION 22 11 17 GAS PIPING AND APPURTENANCES 2.2 PIPE AND FITTINGS A. PIPING (BELOW GROUND) *THIS PIPING IS NOT PART OF OUR SCOPE FOR THE PROJECT THEREFORE NOT INCLUDED IN OUR SUBMITTAL 2.3 VALVES RE-SUBMITTAL INCLUDED IN FULL 2.4 GAS PRESSURE REGULATOR - GR-1,2,3,4,5 RE-SUBMITTAL INCLUDED 2.6 LABORATORY SAFETY DEVICE SYSTEM ISIMET RE-SUBMITTAL INCLUDED
SECTION 22 11 17 GAS AND PIPING APPURTENANCES B. Piping (Above Ground): 1. Pipe and Fittings for 2 inch and smaller in all locations, upstream of manual shut-off valve at emergency shut-off valves - Provide schedule 40, ASTM A 53, black steel with socket weld carbon steel fittings conforming to ANSI B16.11. Pipe larger than 2 inches in all locations: Provide Schedule 40, ASTM A53, black steel pipe with long radius butt weld fittings. All pipe joints located in crawl space, inside walls, above ceiling shall be welded fittings. C. Unions: Use 150-pound standard (300-pound water, oil or gas) malleable iron, ground joint unions, with bronze seat. Provide flange joints for pipe 3 inches and larger in diameter. D. Flanges: Furnish Class 125 ANSI cast iron flanges. E. Where flexible connectors are indicated on the plumbing drawings, the flexible connectors shall be corrugated stainless steel, ASTM A240. with U/V resistant polyethylene jacket, ASTM E84 compliant index for flame and smoke, manufactured by Gastite. 2.3 VALVES A. Ball Valves: For valves downstream of automatic emergency shut-off valve, provide two piece, 600 psi WOG, cast brass body, replaceable reinforced Teflon seats, full port, blowout-proof stem, chrome-plated brass ball, threaded ends, carbon steel handle, quarter turn, MSS-SP-110 compliant, UL listed and CSA approved for natural gas service stamped directly on valve body (125G), manufactured by Nibco Model T-585-70-UL, or approved B. Plug Valves: Lubricated type, suitable for bi-directional dead end service, bubble tight shut-off, Port area at least 80% of the pipe area, self-cleaning plug sealing surfaces, cast iron ASTM A126 Class E body, threaded connection for sizes through 2 inch downstream of emergency shut-off valves, and flanged for all sizes upstream of emergency shut-off valves. Bolted bonnet, permanently lubricated with baked TFE or thermosetting epoxy boded to plug, ball checks, cast iron shaft with wrench operator for sizes smaller than 4 inch, position indicator, memory stop, specifically designed for natural gas service, CGA approved, GSA approval stamped on valve as fuel gas rated, manufactured by Nordstrom Figure 142, 143 or Walworth Figure 2720 and 2721. Contractor has option to provide this valve with threaded ends downstream of automatic emergency shut-off valves. C. Emergency Shut-off Valves. 2-Way, electrically tripped, solenoid type, fail safe closed, manual reset, type 1 solenoid enclosure, 120 volt single phase, continuous duty molded Class F coil, aluminum body, 303 stainless steel stem and springs, threaded ends, rated & listed for natural gas service, suitable for mounting in vertical position, manufactured by Red Hat Model No. 8044A2 2.4 GAS PRESSURE REGULATOR A. GR-1(Domestic water heaters): Gas pressure regulator, 5 psi inlet pressure and 9 inch w.c. outlet pressure setting (spring range 6 inches w.c to 14 inches w.c.), minimum rated for 200 cfh at pressure setting, manufactured by Equimeter or approved equal. B. GR-2(mechanical boilers): Gas pressure regulator, 5 psi inlet pressure and 11 inch w.c. outlet pressure setting (spring range 6 inches w.c to 14 inches w.c.), minimum rated for 1500 cfh at pressure setting, manufactured by Equimeter or approved equal. C. GR-3(Kitchen): Gas pressure regulator, 5 psi inlet pressure and 10 inch w.c. outlet pressure setting (spring range 6 inches w.c to 28 inches w.c.), minimum rated for 1000 cfh at pressure setting, manufactured by Equimeter or approved equal. ACADEMIC BUILDING & PATRIOT S CASA Texas A&M University San Antonio ERP-4 (11-27-12) Project No. 25-3122 22 11 17-3 GAS AND PIPING APPURTENANCES
AHEAD OF THE FLOW Bronze Ball Valves Two-Piece Body Full Port ¹ ₄"-1" Conventional Port 1¹ ₄"-3" Bronze Trim Blowout-Proof Stem UL Listed 250 PSI/17.2 Bar Non-Shock LP Gas per UL842 www.nibco.com Revision 11/3/2008 Dezincification Resistant CONFORMS TO MSS SP-110 CSA certified to ANSI/ASME B 16.33 and CGA 3.16 for Natural and Propane Gas to 125 PSIG (¹ ₄"-1") MATERIAL LIST Specification Part 1. Handle Nut Zinc Plated Steel 2. Handle Zinc Plated Steel Clear Chromate Plastisol Coated 3. Threaded Pack Gland Brass ASTM B 16 Alloy C36000 4. Packing PTFE 5. Stem Silicon Bronze ASTM B 371 Alloy C69430 or ASTM B 99 Alloy C65100 6. Thrust Washer Reinforced PTFE 7. Ball Brass ASTM B 124 Alloy C37700 or ASTM B16 Alloy C36000 EACH with Hard Chrome Plate 8. Seat Ring (2) Reinforced PTFE 9. Body Bronze ASTM B 584 Alloy C84400 10. Body End Piece Bronze ASTM B 584 Alloy C84400 T-585-70-UL ¹ ₄"-1" Full Port CSA Threaded T-580-70-UL 1¹ ₄"-3" Conventional Port Threaded UL Only UL Listed For: YSDT LP gas shut-off YQNZ Compressed gas shut-off YRPV Gas shut-off YRBX Flammable liquid shut-off MHKZ Manual valves CUL Listed For: YSDT7 LP gas shut-off for Canada Service A - Air or non-toxic, non-flammable gas G - City gas supplied by public utilities GA - Gasoline LP - Liquified petroleum gas, 250 PSI max. 02 - No. 1 and 2 fuel oil 04 - No. 4 fuel oil 05 - No. 5 fuel oil 06 - No. 6 fuel oil DIMENSIONS WEIGHTS QUANTITIES Dimensions T-585-70-UL Size A B C D T-580-70-UL Master In. mm. In. mm. In. mm. In. mm. In. mm. Lbs. Kg. Ctn. Qty. ¹ ₄ 8 2.00 51 1.75 44 5.00 127.38 10.45.21 100 ³ ₈ 10 2.00 51 1.75 44 5.00 127.38 10.45.20 100 ¹ ₂ 15 2.44 62 1.88 48 5.19 132.50 13.64.29 100 ³ ₄ 20 2.94 75 2.25 57 6.25 159.75 19 1.33.60 50 1 25 3.34 85 2.38 60 6.44 164 1.00 25 1.79.81 40 1 ¹ ₄ 32 3.94 100 2.63 67 6.75 171 1.00 25 2.17.98 20 1 ¹ ₂ 40 4.31 109 3.00 76 8.88 226 1.25 32 3.27 1.48 20 2 50 4.63 118 3.16 80 9.06 230 1.50 38 5.09 2.31 10 2 ¹ ₂ 65 5.84 148 3.50 89 9.66 245 2.00 51 8.25 3.74 6 3 80 7.09 180 4.41 112 11.53 293 2.50 64 15.65 7.10 4 NIBCO Supplies Full Port T-585-70-UL on this size. T-585-70-UL T-580-70-UL NPT x NPT 22 NIBCO INC. WORLD HEADQUARTERS 1516 MIDDLEBURY ST. ELKHART, IN 46516-4740 USA PH: 1.800.234.0227 TECH SERVICES PH: 1.888.446.4226 FAX: 1.888.336.4226 INTERNATIONAL OFFICE PH: +1.574.295.3327 FAX: +1.574.295.3455 www.nibco.com
=======HOMESTEAD LUBRICATED PLUG VALVES ======= Standard Opening Semi-Steel Straightway - Wrench Operated Rectangular Port 200 lb. WOG 150 lb. SWP Test: Air under water 200 p.s.i.g. U.L. Listed U.L. Listed 1" thru 4" 1" thru 6" I II. I.~,. " 'l~... '.:~ -..... CSA; CONSULT FACTORY FOR SIZES LISTED r Fig. 611 - Semi-Steel, Screwed DIMENSIONS Fig. 612 - Semi-Steel, Flanged SIZE - INCHES 1" 1%" 11," 2" 21," 3" 4" 5" 6" 8" End to end A 4% 5 5 6 6 3 ;. ]5;. 9 - - Face to face A 51, 6 61, 7 7 1 1, 8 9 101, 101, 111, Flange diameter G 4% 4 5 ;. 5 6 7 71, 9 10 11 131, Flange thickness E 71.. 1, 91.. 5;. lll.. 3;. lsi.. 1 1 1';. Number of drilled holes in flange Y 4 4 4 4 4 4 8 8 8 8 Number of topped holes in flange X - - - - - - - - - Center to top of stem (Fig. 611) D 2 29 /'2 3 5 1.. 3 5 1.. 4 5';. 5 13 /'2 6 17 /'2 - - Center to top of stem (Fig. 612) D 2 29 /'2 3 5 1.. 31, 4 5';. 5 13 /'2 6 17 /'2 7';. 7 3 ;. 9 3 1.. Length of lubricant screw L PI.. PI.. PI.. PI.. 21, 21, 21, 3';' 3';' 3'/a Lubricant stick diameter - 3;. 3;. % % 1, 1, 1, II, II, II, Standard wrench size - F G G G E E l N N N Center of port to bottom C 2 11 /'2 1 2Y.. 2'1.. 3';. 3 29 /'2 4 3 1.. 4 29 /'2 6/'2 61/'2 6 1 1, Dimen. of square on stem H 2'/'2 29/'2 29/'2 29/'2 F/'2 F/'2 PI, 2 2 2 Extreme width of Scrd. body R 2';. 31, 3% 3% 5 5';' 6% - - Extreme width of Flgd. body R 4% 4% 5 6 7 71, 9 10 11 131, Weight, lb. - Fig. 611-4 1 1, 7 1 ;. 7 1 ;. 13% 191, 33 3 ;. 58 1 /; - - Weight, lb. - Fig. 612-71, 101, 101, 19 291, 39 611, 88 100 172,----,.,m For 8" and larger sizes also see Fig. 612-A. Face to face dimensions are in accordance with ANSI 816.10. Flanges are drilled to 125 pound ANSI 816.1. Drilling other than standard is extra. Prices include drilling; and no reduction is made for valves not drilled. Combination 8uttonhead Fitting and Lubricant Screw (pictured on page 26) is standard on all valves. ALL Types of Plug Valves Since 1892 9