INSTRUCTION MANUAL Features - Carbon fiber main blade, tail blade, fly paddle, tail fin for extra weight saving and durability. - CNC machined high grade aluminum rotor head and tail gear box to ensure sensitive and accurate control. - +/- 5 patch range for extreme 3D maneuver. - One way drive gear for auto rotation maneuver. - Direct to swash CCPM system to ensure quick and slop-free control. - Direct belt drive tail rotor system to ensure quick response and minimize power lost. - Adjustable battery mount for quick CG adjustment to suits different flying style. - mm main shaft for extra strength and durability for extreme 3D maneuver. - Low fraction anti slip mm tail drive belt to ensure strength and durability. - Fiber glass high strength canopy. - High strength hex screws system to ensure durability and strength. - All aluminum parts were made by preciously CNC machined high grade aluminum. www.copterx.com Copyright 009 KY MODEL Company Limited.
MENU Table of content............................................................................ Introduction.............................................................................. Precaution.............................................................................. 3. Safety Tips............................................................................... Self-preparation (Equipment)......................................................... 3 5. Self-preparation (Tools)............................................................... 3 6. Symbols Guide.......................................................................... 7. Assembly Section....................................................................... 5 8. Pitch and Throttle Setting............................................................ 0 0
. Introduction Thank you for choosing CopterX Black Angel! You are about to enter the world of high performance electric powered mini helicopter. Black Angel is developed by our professional team with full 3D capability. Please read the following instruction to ensure proper operation of this model. And keep a copy of this manual for future reference.. Precaution CopterX R/C helicopter are NOT A TOY. Improper use of these products may cause serious injury or death. Manufacture and seller assume no liability for the operation or use of this product. For intermediate and advanced pilot, Black Angel is able to offer performance unheard of by other rivals. For less experience pilot it would be helpful to seek advice from experienced pilot for setup and operation to enjoy the full potential of you new flying machine. Please check all screw and cabon fiber parts for wear, creaks, or missing before and after each flight. Ensure all screw are tight and apply thread lock when necessary. Replace all worn out or broken parts necessary. Please use gunnies CopterX parts to ensure proper operation with you model. Black Angel is a consumer item. Any damage or dissatisfaction as a result of accidents or modifications are not covered by any warrantee and cannot be returned for repair or replacement. Please contact our local distributors for free technical consultation and replacement parts when you experience problems during operation or maintenance. 3. Safety Tips 0 Black Angel Only operate Black Angel in detonated air field away from crowds and keep save distance with helicopter. Do not operate model under drug influence, poor physical health or extreme weather conditions. Keep save distance within tall building, power cables and automotive as these situation may effect the range of the transmitter. Keep Black Angel away from moisture and other contaminants as there are a lot of electrical component on this copter. These situations may cause malfunctions of the helicopter and possible injury or death. Black Angel was designed for leisure and 3D flying. Please do not use it for any other purpose which this product is not design for. Keep Black Angel away from high temperature and flames to avoid damage to the helicopter and possible fire.
. Self-preparation (Equipment) Radio control equipment is necessary to complete the assembly. (Not included in kit) Brushless Motor Gyro Brushless ESC Li-Poly Battery Transmitter (6ch, helicopter system) Reveiver (6ch or more) Micro Servo x 3pcs(movements) Micro Servo x pcs(tailrudder) Blade 5. Self-preparation (Tools) Tools is necessary to complete the assembly. (Not included in kit) Scissors Cutter Knift Needle Nose Pliers Plug Wrench (mm 5.5mm) 03
6. Symbols Guide Black Angel When following symbols were shown, please add glue or oil accordingly to ensure proper operation. Thread Lock Oil CA Glue Apply Thread Lock into threaded hole and wipe of excess if necessary. 0
7. Assembly Section 006 Feathering Shaft Ø x5.5 0000 Dumper Rubber Ø 8x Ø x 3 00D Metal Main Rotor Housing 00.5mm Pin Ø.5x0 5 3 6 7 8 9 0 Smaller ID Tight Fit On Metal Main Rotor Housing 3 Larger ID Loose Fit On Metal Main Rotor Housing Larger ID Loose Fit On Metal Main Rotor Housing Smaller ID Tight Fit On Metal Main Rotor Housing 5 0070 M.5x6 Socket Screw M.5x6 6 03003 M7 Flat Washer Ø 7x Ø.5x0.5 7 07007 Ø 7x Ø x,5 Bearing Ø 7x Ø x.5 8 03003 M7 Flat Washer Ø 7x Ø x0.5 9 07007 Ø 9x Ø x Thrust Bearing Ø 9x Ø x 0 005B Metal Main Blade Holder 070079 Ø9 x Ø x Bearing Ø 9x Ø x 007 M6 Flat Washer Ø 6x Ø x.5 3 6009 Linkage ball 05
07007 Ø 5 Flanged Bearing Ø 5x Ø x.5 5 0B Flybar Seesaw 6 070073 Ø 5x Ø x.5 Bearing Ø 5x Ø x.5 7 060 Flybar Ø x09 8 03003 Ø 3x Ø x0.5 Washer Ø 3x Ø x0.5 9 007 Mx6 Screw Mx6 9 8 5 6 7 0 8 Press together tightly 3 7 6 5 0 007 M3x3 Set Screw M3x3 008B SF Mixing Arm 3078 Ball Link 3 0B Flybar Control Arm 070073 Ø 5x Ø x.5 Bearing Ø 5x Ø x.5 5 03003 Ø 3x Ø x0.5 Washer Ø 3x Ø x0.5 6 03B Flybar Control Rod 7 6009 Linkage Ball 8 50B Flybar Weight 06
9 007 Mx0 Screw Mx0 30 0090 Mx7 Collar Screw Mx7 3 07 Radius Arm 3 0B Washout Base 33 6009 Linkage Ball 8 3 03003 Ø 3x Ø x0.5 Washer Ø 3x Ø x0.5 35 09B Swashplate 36 600 Long Linkage Ball 37 0075 Mx6 Screw Mx6 38 070073 Ø 5x Ø x.5 Bearing Ø 5x Ø x.5 39 05 Washout Control Arm 0 008 M Socket Head Mx8 00B Metal Head Stopper 0080 Mx Socket Head Mx 3 003 Main Shaft Ø 5x 0077 M Nylock Nut 9 30 3 0 3 33 39 38 3 35 36 37 3 6.5mm 8mm 3 3mm 3 07
5 070075 Ø x Ø 5x5 Bearing Ø x Ø 5x5 6 0B Main Shaft Bearing Block 7 03B Motor Mount 8 085B Frame Mounting Bolt(Motor) 9 083B Frame Stiffener 50 007 Mx6 Screw Mx6 6 5 007 Mx Screw Mx 6 5 03B Canopy Mounting Bolt 53 5069B Main Frames 5 080B Frame Mounting Bolt 5 55 0078 Mx Flat Head Screw Mx 56 07B Bottom Plate Mount 57 5037B Back Bottom Plate 58 5036B Front Bottom Plate 5 6 5 50 53 7 5 8 5 50 55 55 9 58 56 57 56 08
59 6 5035B 038B Battery Mounting Plate Aluminum Battery Mounting Base 60 6 0078 505 Mx Flat Head Screw Anti-Rotation Plate Mx 5 63 007 Mx Screw Mx 8 6 08B Anti-Rotation Mount 65 007 Mx0 Screw Mx0 66 09 Pulley Set 59 60 63 6 6 63 6 65 66 67 68 69 63 7 70 7 60 73 63 67 070073 Ø 5x Ø x.5 Bearing Ø 5x Ø x.5 68 030 Pulley Collar 69 08B Pully Mount 70 03B Tail Boom Mount 7 076B Rear Gyro Mount 7 mm Nylock Nut 73 008 Mx3 Collar Screw Mx3 09
76 065 Tail Drive Gear 77 063 Main Drive Gear Hub 78 070077 One Way Bearing Ø 0x Ø 6x 79 033 Main Drive Gear 80 0090 Mx7 Collar Screw Mx7 3 8 07 One Way Bearing Shaft 79 76 77 78 80 8 75 7 7 007 Mx6 Screw Mx6 75 0 306B Landing Skid
8 007 M3x3 Set Screw M3x3 83 06 5mm Collar 8 000 Drive Belt 8 0077 M Nylock Nut M 86 080 Mx0 Socket Head Mx0 8 83 8 85 86 90 9 9 87 88 89 87 303 Metal Tail Boom Ø x Ø x30 88 3039 Rudder Servo Mount 89 33 Rudder Control Rod 90 0073 Mx8 Screw Mx8 9 3077 Rod Guide 9 3078 Ball Link
93 306 Idle Pully 9 070073 Ø 5x Ø x.5 Bearing Ø 5x Ø x.5 95 30B Metal Tail Case 96 070078 Ø 8 Flanged Bearing 97 0075 Mx6 Screw Mx6 98 007 Mx6 Screw Mx6 6 99 307B Aluminum Bolt 00 300 Tail Rotor Shaft 0 0077 Nylock Nut M 0 308 Control Arm Mount 03 007 Mx Screw Mx 0 0073 Mx8 Screw Mx8 05 303 Vertical Stabilizer Mount 06 305 Ø 3.5x Ø x.5 Vollar Ø 3.5x Ø x.5 93 97 98 move freely after tightening 98 06 9 98 05 9 93 99 00 98 0 0 03 98 05 07 0077 M Nylock Nut M 08 030037 Ø 5x Ø x0.5 Washer Ø 5x Ø x0.5 09 070076 Ø 6x Ø 3x.5 Bearing Ø 6x Ø 3x.5 0 3056B Tail Blade Holder 070080 Ø 7x Ø 3x3 Bearing Ø 7x Ø 3x3 3055B Tail Hub 3 33058 Collar 3057B Tail Control Link 5 0073 Mx8 Screw Mx8 move freely after tightening 3 08 07 5 09 0
6 305B Slide Shaft 7 07008 Ø 8x Ø 5x.5 Bearing 8 305B Bearing Holder 9 305B Rudder Control Arm 0 0090 Mx7 Collar Screw Mx7 33059 Collar B Mx6 0087 M Nut 3 03003 Ø 3x Ø x0.5 Washer 309B Tail Rotor Bell Crank 5 07007 Ø5 Flanged Bearing 6 007 Mx0 Screw Mx0 7 6009 Linkage Ball 8 007 M3x3 Set Screw M3x3 6 0 8 9 7 move freely after tightening 8 3 5 7 6 3
9 0073 Mx8 Screw Mx8 30 306B Tail Boom Brace End 3 33 35 09009 300 007 Metal Tail Boom Brace CF Horizontal Stabilizer Mount Mx Screw Mx 3 3 36 007 350 350 Mx6 Screw CF Horizontal Stabilizer CF Vertical Stabilizer Mx6 37 0087 M Nut 38 007 Mx0 Screw 39 3079 CF Tail Blade 3 35 38 39 37 33 35 3 36 3 30 9 0.05-0.mm Adjust motor so gear mesh is 0.05-0.mm Check for smooth operation 0 5 3 0 0085 M3x6 Socket Head M3x6 307 Motor Pinion Gear 0088 M3x3 Set Screw M3x3 3 Motor (Not included) Receiver (Not Included) 5 Double Sided Tape
6 Servo (Not included) 7 Gyro (Not included) 8 M Nut 6 9 0073 Mx8 Screw Mx8 0 50 Double Side Tape 6 8 8 6 9 9 9 6 9 50 8 6 7 II mm I II 6mm II 5 I
5 0076 M3x6 Socket Head M3x6 5 0080 CF Paddle 3 53 CF Main Rotor Blade 5 0086 M3 Nylock Nut M3 55 008 Canopy Grommet 56 0083 Canopy 57 008 Receiver Antenna Tube 5 5 53 5 55 56 57 3.6 A=90 Tail servo horn When A be 90, B will be around 3.6mm After setting Head Lock mode, correct position of tail servo and tail pitch assembly as photo. If the tail pitch assembly is not at the neutral position, please adjust the length of rudder control rod. 6
0 Set flybar paddle horizontally Set control arm horizontally Set swashplate horizontally Battery Rudder Servo ESC Motor Gyro Receiver position FUTABA / HITEC Transmitter / Servo JR Transmitter / Servo Pitch: CH6 Aileron: CH Elevator: CH Elevator: CH3 Aileron: CH Pitch: CH6 Aileron (CH) Throttle (CH) ESC Elevator (CH) Throttle (CH3) ESC 6 channel receiver Aileron (CH) Elevator (CH3) 6 channel receiver Rudder (CH) Pitch Gyro (CH5) Gain channel wire Rudder (CH) Pitch Gyro (CH5) Gain channel wire HITEC, FUTABA 6ch receiver writing 7 JR 6ch receiver writing
MODE UP DOWN Tilt Right Fly Forward Fly Backward Fly Forward Tilt Left Left Right Fly Backward UP UP RIGHT LEFT Ascent Right Descent Ascent / Acceleration HIGH LOW Descent / Deceleration 8 Left Left Right
MODE UP DOWN Tilt Right Fly Forward Fly Backward Fly Forward Tilt Left Left Right Fly Backward UP UP RIGHT LEFT Ascent Right Descent Ascent / Acceleration HIGH LOW Descent / Deceleration 9 Left Left Right
8. Pitch and Throttle Setting General Flight +9 ~+ Stick position at high / Throttle 00% / Pitch +9 ~+ +5 ~+6 GENERAL FLIGHT Throttle Pitch 5 00% High speed +9 ~+ 85% 3 65%~70% Hovering +5 ~+6 0% 0% Low speed 0 Stick position at Hovering / Throttle 65%~70% / Pitch +5 ~+6 0 00 85 65 0 3 5 3D Flight Stick position at low / Throttle 0% / Pitch 0 +9 ~+ IDLE Throttle Pitch 5 00% +9 ~+ 85% 3 80% +5 ~+6 85% 90% -5 Stick position at high / Throttle 00% / Pitch +9 ~+ 0 00% 90% 85% 80% 3 5 Stick position at middle / Throttle 90% / Pitch 0-9 ~- IDLE Throttle Pitch 5 00% High +9 ~+ 3 90% Middle 0 00% Low -9 ~- 00% 85%~95% Stick position at low / Throttle 00% / Pitch -9 ~- 0
www.copterx.com Copyright 009 KY MODEL Company Limited.