INSTALLATION INSTRUCTIONS Accessory XM RADIO SYSTEM Application 2014 CIVIC 2 AND 4-DOOR Publications No. AII 50687 Issue Date NOV 2013 PARTS LIST XM Radio Attachment Kit P/N 08B15-TR0-100 Bus cable Clip Wire tie with clip 2 Brackets Accessory User s Information Manual 2 Spacers (Some may not used) 6 Washer bolts XM Antenna Kit (sold separately) P/N 08A15-0J1-100 Antenna 7 Wire ties Unit Kit (sold separately) P/N 08A15-TR0-100 XM radio unit 8 Urethane tapes Cover seal 2-Port bus cable Kit (sold separately) P/N 08A31-0F1-000 2-Port bus cable 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 50687 (1311) 08B15-TR0-1001-90 1 of 12
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Shop towel Scissors Ratchet 8 mm and 10 mm Sockets Isopropyl alcohol Tape measure Diagonal cutters Tape The following tool is available through the Honda Tool and Equipment Program. On the in, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under Search. Or, call 888-424-6857. Plastic Trim Tool (T/N SILTRIMTL10) Illustration of the XM Radio System in the Vehicle XM RADIO UNIT BUS 2-PORT BUS Q081801AK BUS XM RADIO UNIT 2-PORT BUS AUDIO UNIT Q082009AK 2 of 12 AII 50687 (1311) 2013 American Honda Motor Co., Inc. All Rights Reserved.
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 3. Wrap the end of a flat-tip screwdriver with tape. Locate the slot in the bracket cover, and insert a flattip screwdriver into the slot. Push the hook with the flat-tip screwdriver. FLAT-TIP SCREWDRIVER BRACKET COVER 1. Disconnect the negative cable from the battery. 2. Remove the passenger s sunvisor holder. HOOK SUNVISOR FRONT SUNVISOR Make sure the hook slides into the bracket cover. SUNVISOR HOLDER (Rotate.) Q082007AK Push the hook. While pushing in on the hook, rotate the sunvisor backward about 45. Q091503BK 4. While pushing in on the hook, rotate the passenger s sunvisor backward about 45. Make sure the hook slides into the bracket cover. NOTE: If the hook did not stay pushed in, return the passenger s sunvisor to its original position and repeat steps 3 and 4. 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 50687 (1311) 3 of 12
5. Remove the passenger s sunvisor. For 4-Door Models 8. Pull away the passenger s door opening seal. Pull the clip. FRONT TRIM SUNVISOR Q091504AK For 2-Door Models 6. Pull away the passenger s door opening seal. Pull the clip. DOOR SEAL (Pull away.) QA20101AK 9. Pull out the passenger s A-pillar trim to release the clips. 10. Put a shop towel in the opening between the passenger s A-pillar trim and the dashboard to prevent dropping the A-pillar clips. Take care not to damage the passenger s A-pillar trim. TRIM TRIM 2 S DOOR SEAL (Pull away.) Q082004AK 7. Pull out the passenger s A-pillar trim to release the clips. DASHBOARD SHOP TOWEL Q091502AK 4 of 12 AII 50687 (1311) 2013 American Honda Motor Co., Inc. All Rights Reserved.
11. Remove the passenger s A-pillar trim from the upper clip (unplug the vehicle connector, if equipped). Carefully remove the shop towel and any clips that fell from the passenger s A-pillar trim. NOTE: The upper clip will stay in the body. 13. Install the new clip (supplied) to the passenger s A-pillar trim. NOTE: When reinstalling the A-pillar trim, refer to the service manual for the correct overlap procedure. CONNECTOR (if equipped) UPPER (supplied) TRIM TRIM Q0N0533AH 12. Remove the remaining upper clip from the passenger s A-pillar. Q082309AK 14. Remove the passenger s front door sill trim (six clips, two hooks, and four retaining tabs). 2 HOOKS Push two tabs. FRONT 6 S UPPER (Discard.) Q082006AK FRONT DOOR SILL TRIM 4 RETAINING TABS Q082003AK 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 50687 (1311) 5 of 12
15. Pull away the door opening seal, and remove the passenger s kick panel (two clips). Open the glove box, push inward on the stops, and remove the glove box. STOPS (Push inward.) DOOR SEAL (Pull away.) KICK PANEL 16. Remove the glove box: Remove two bolts. Q081901AK Q072102AH 17. To protect the vehicle, attach tape to the dashboard in the areas shown. Move the shift lever to the N (neutral) position, and wrap a shop towel around the shift lever. SHIFT LEVER (N POSITION) 2 BOLTS Q072101BH CENTER LOWER PANEL SHOP TOWEL QB51501BK 6 of 12 AII 50687 (1311) 2013 American Honda Motor Co., Inc. All Rights Reserved.
18. Remove the center lower panel (two self-tapping screws, four clips, and unplug the vehicle connectors, if equipped). 20. To protect the vehicle, attach tape to the dashboard, center panel, and wiper/washer switch in the areas shown. CONNECTORS (if equipped) 4 S WIPER/WASHER SWITCH DASHBOARD CENTER LOWER PANEL 2 SELF-TAPPING SCREWS QB41901AK CENTER PANEL QB51701BK 19. Remove two bolts and two self-tapping screws. 21. Remove the center panel (six clips, aspirator hose, and unplug the vehicle connectors). 6 S ASPIRATOR HOSE CONNECTORS 2 SELF-TAPPING SCREWS 2 BOLTS QB51704AK CENTER PANEL QB41301BK 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 50687 (1311) 7 of 12
Installing the XM Radio Unit 22. Loosely install two brackets to the audio unit with two washer bolts. NOTE: There is the gap between the brackets and XM radio unit. Use the spacer to adjust the gap. 25. Using isopropyl alcohol on a shop towel, clean the area on the edge of the XM radio unit as shown. Clean with isopropyl alcohol. AUDIO UNIT 2 CUT URETHANE S 2 WASHER BOLTS (Loosely install.) 2 BRACKETS XM RADIO UNIT URETHANE (Cut.) Q081807BK BRACKET 26. Cut the urethane tape as shown. 27. Attach two halves of urethane tape to the XM radio unit as shown. QB51702AK SPACER (There is the gap between the brackets and XM radio unit.) 23. Install the XM radio unit to the brackets in the audio unit with four washer bolts. 28. Wrap two urethane tapes around two 2-port bus cable connectors as shown. 2 URETHANE S AUDIO UNIT 2-PORT BUS Align. Align. Q081808AK 2 BRACKETS 2 WASHER BOLTS 4 WASHER BOLTS XM RADIO UNIT QB51703BK 24. Secure two washer bolts installed in step 22. 8 of 12 AII 50687 (1311) 2013 American Honda Motor Co., Inc. All Rights Reserved.
29. Plug the bus cable connector into the XM radio unit. Routing the Antenna Cable 31. Cut three urethane tapes in half as shown. 850 mm (33.5 in.) XM RADIO UNIT 50 mm (2.0 in.) 150 mm (5.9 in.) BUS Q081702AK 30. Plug the 2-port bus cable into the audio unit connector and the bus cable connector. 3 URETHANE S (Cut.) 32. Wrap six halves of urethane tape around the antenna cable at the measurements shown. Q0N1501AK AUDIO UNIT 2-PORT BUS 33. Using isopropyl alcohol on a shop towel, clean the area shown on the inside of the windshield. INSIDE Align. BUS Q081703AK 50 mm (2.0 in.) Clean with isopropyl alcohol. WINDSHIELD 4 ADHESIVE BACKINGS Q081705BK 34. Remove four adhesive backings from the antenna, and attach the antenna in the location shown. Apply firm pressure to securely attach the antenna. 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 50687 (1311) 9 of 12
35. Using isopropyl alcohol on a shop towel, clean the area shown on the outside of the windshield. 39. Route the antenna cable down. Loosely secure the antenna cable to the vehicle harness with one wire tie. Align. OUTSIDE WIRE TIE (Loosely secure.) HARNESS Clean with isopropyl alcohol. COVER SEAL 36. Remove the adhesive backing from the cover seal, and attach it to the outside of the windshield, positioned over the antenna. 37. Cut one urethane tape as shown. Q081706BK 40. Route the antenna cable to the center panel opening as shown. CENTER PANEL Q081708BK (Clean with isopropyl alcohol.) URETHANE (Cut.) Q091550AK URETHANE (Cut in step 26.) Q081707BK 38. Route the antenna cable along the passenger s A- pillar. Using five pieces of urethane tape, secure the antenna cable to the passenger s A-pillar in the areas shown after cleaning with isopropyl alcohol on a shop towel. NOTE: Do not attach the urethane tape over any vehicle holes, pay attention to the orientation of the urethane tape. 10 of 12 AII 50687 (1311) 2013 American Honda Motor Co., Inc. All Rights Reserved.
41. Route the antenna cable through the center panel opening, and align it with the vehicle connector. 44. Secure the antenna cable to the vehicle panel with one wire tie with clip in the area shown. CONNECTOR CENTER PANEL HARNESS WIRE TIE WITH Align. WIRE TIE QB51801AK PANEL Q081804BK 42. Secure the antenna cable to the vehicle harness with one wire tie. 45. Secure the antenna cable to the vehicle frame with two wire ties. 43. Secure the antenna cable to the vehicle harness with two wire ties. HARNESS 2 WIRE TIES FRAME Q081803BK 2 WIRE TIES QB51802AK 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 50687 (1311) 11 of 12
46. Cut one urethane tape, and wrap the piece of urethane tape around the antenna cable as shown. 48. Bundle the antenna cable, and secure it to the vehicle harness with one wire tie. 30 mm (1.2 in.) URETHANE (Cut.) Q091551BK 47. Secure the antenna cable to the vehicle frame with one wire tie. FRAME WIRE TIE Q091553AK Do not fold the antenna cable. WIRE TIE (Tighten one wire tie secured in step 39.) HARNESS Q091552BK 49. Plug the 2-port bus cable connector to the vehicle connector. 50. Plug the antenna cable connector to the XM radio unit. 51. Plug the vehicle connectors to the audio unit, and reinstall the center panel. 52. Check that all wire harnesses are routed properly and all connectors are plugged in. 53. Check the overlap between the headliner and the passenger s A-pillar trim. Refer to the service manual. If necessary, adjust the overlap. 54. Reinstall all removed parts. 55. Connect the negative cable to the battery and check operation of all lights and other electrical accessories. 56. Press and hold the radio power button for two seconds to restore radio and navi (if equipped) system functions. 57. Reset the clock on vehicles without navigation. 58. Check the operation of the XM radio system according to the Accessory User s Information Manual. 12 of 12 AII 50687 (1311) 2013 American Honda Motor Co., Inc. All Rights Reserved.