Horizontal pre-adjustment device for measuring devices Internal precision measuring instruments, external micrometers, measuring screws, etc. These automatically operated pre-adjustment devices were developed to pre-set and check all measuring devices with 2-point and 3-point contact (indoor precision measuring devices, expansion probe measuring devices, external micrometers, quick callipers, 2-point internal micrometers, dial gauges, lever gauges). Advantage: You do not need a variety of adjustment standards such as setting rings and gauge blocks; in addition, all adjustments are performed with only one TPS pre-adjustment device Application: Depending on the measuring device to be checked, the corresponding add-ons for an easy and safe centring (optional accessories) are used. The dimension to be checked is entered via the keyboard on the operator panel, the moving skid travels to the requested point automatically and with max. precision. The check or, if required, re-adjustment can be carried out now on the measuring device. TESA TPS 300 500 1000 Measuring range for internal measurements mm 1-305 1-508 1-1016 Measuring range for external measurements mm 40-330 40-532 40-1040 Numerical increment mm 0,001 0,001 0,001 Error limits 1,5 m + 3.33 x L x 10-6 1,5 m + 3.33 x L x 10-6 1,5 m + 3.33 x L x 10-6 repetition precision (2s) m 1 1 1 Data output RS232 RS232 RS232 Prod. Gr. 366 hspecial designs with measuring ranges 1500, 2000 or 3000 mm on request. Additional information, advice and quotations available on request. 3-D articulated measuring stands Model series with high-quality light metal arm components mechanical, maintenance-free central clamping microfine adjustment with combined holder for dial gauges, with shank Ø 8 mm and a lever gauge with a dovetail holder Advantages: simple, quick operation high movement, exact positioning Ident. No. 003-010 Basis: heavy magnetic foot, with prismatic base. Adheres to all plane steel and cast iron surfaces in any position! Ident. No. 015 Cylindrical mounting spigots Ø 10 mm for clamping in collet and drill chucks. For alignment and zero setting of workpieces and appliances. Ident. No. 018 Basis: switching magnet with contour bond The steel laminated sheets match the support surface. Suitable for uneven surfaces. and lever gauge Ident. No. 010 Ident. No. 015 Ident. No. 003 Ident. No. 018 Overall height approx. mm 200 220 300 310 380 Action radius approx. mm 130 130 200 200 280 Magnetic foot, length x width x height approx. mm Ø 10x40* 34 x 30 x 35 60 x 50 x 55 91 x 52 x 55 60 x 50 x 55 Adhesion force** approx. N 300 750 600 750 34060 Ident. No. 015 003 005 018 010 O. R. O. R. O. R. O. R. * With cylindrical mounting spigots (Width x Length). * 818 Edition 5

3-D jointed measuring stands Model series with chrome-plated arm components mechanical, maintenance-free central clamping microfine adjustment with combined holder for dial gauges, with shank Ø 8 mm and a lever gauge with a dovetail holder Advantages: simple, quick operation high movement, exact positioning Overall height approx. mm 310 390 568 740 Action radius approx. mm 200 280 450 630 Magnetic foot, length x width x height approx. mm 60 x 50 x 55 60 x 50 x 55 75 x 50 x 55 120 x 60 x 55 Adhesion force** approx. N 800 800 1000 1500 34060 Ident. No. 027 021 023 025 O. R. O. R. O. R. 3-D jointed measuring stands Model series with chrome-plated arm components Application: especially designed stand for precision measurements by means of precision pointers. extremely reinforced articulated arm with mechanical, maintenance-free central clamping for max. stability. -line micro fine adjustment for precise fine adjustment (1 rotation 0.1 mm), with combined holders for precision pointer with shank Ø 8 mm and probe lever gauges with dovetail strong switch-magnet base with prismatic base for standing stability in all positions. Advantages: simple, quick operation high movement precise positioning Delivery: without precision pointer Ident. No. 025 Overall height approx. mm 435 Action radius approx. mm 330 Magnetic foot, length x width x height approx. mm 75 x 50 x 55 Adhesion force** approx. N 900 34060 Ident. No. 100 Delivery without precision pointer Edition 5 819

Case set Holding system for small parts from the workshop Convenient jointed arm with accessories to hold everything in place when two hands are just not enough. Allows precise positioning and secure carrying of light sources, objects, monitors or cameras, depending on the type of use. Delivery scope: articulated stand, steel base, plug-in socket, locking clamp with plastic jaws, extension, adapter, toping thread and straddle wrench Action radius approx. mm 200 Steel base Ømm 100 Clamping socket mm 80 x 20 x 40 Extension mm 200 34060 Ident. No. 150 Combi system For universal use in the construction of measuring equipment, fixtures and jigs, as well as for other applications and areas of use. Recommended system combinations from the following groups, No. 34075: 1 2 3 4 5 6 7 8 9 : A U U B U U U U U C U U U U U D U U U E U U U U F U U 3-D articulated arms patented, mechanical and dust-protected central clamping (without hydraulic oil). Advantage: Unlimited movement, joints are fixed or loosened simultaneously with a grip. Version A B C D E F Action radius mm 130 200 280 330 450 630 Connecting thread top M6 M6 M6 M8 M8 M8 Connecting thread bottom M6 M8 M8 M8 M8 M10 x 1.25 34075 Ident. No. 100 110 120 125 131* 141 O. R. O. R. O. R. O. R. O. R. * With adapter piece of M8 to M10 x 1.25 and washer Ø 32 mm Ident. No. 100 Ident. No. 120 Ident. No. 131 Micro fine adjustment From steel with a combined holder for a shank Ø of 8 mm and a sensing lever gauge with a dovetail holder. Version 1 Standard 2 Standard 3 -line Connecting thread M6 M8 M8 34075 Ident. No. 200 210 220 O. R. O. R. Ident. No. 200 Ident. No. 220 820 Edition 5

Magnetic bases/granite feet/vacuum bases Ident. No. 300-330 Switching magnet feet Ident. No. 340 Granite foot, to be used on measuring plates, can be moved Ident. No. 350 Vacuum base, adheres securely to natural stone measuring plates Ident. No. 360 Switchable Anyform magnetic base, adheres to uneven surfaces. 4 5 6 7 8 9 : Version Magnetic clamp Magnetic clamp Magnetic clamp Magnetic clamp Granite foot Vacuum base Anyform magnetic clamp Connecting thread M6 M8 M8 M10 x 1.25 M8 M8 M8 L x W x H mm 34 x 30 x 35 60 x 50 x 55 75 x 50 x 55 120 x 60 x 55 150 x 120 x 50 Ø 88 x 27 91 x 52 x 55 Adhesion force**/weight 300 N 750 N 1000 N 1500 N 2 kg 400 N 600 N 34075 Ident. No. 300 310 320 330 340 350 360 O. R. O. R. O. R. O. R. O. R. O. R. * Dial gauge magnetic holders No. 34100 simple handy version with a thick magnetic base plate. No. 34110 Mounting surface with 2 strong, round sintered magnets, providing good adhesion properties. Dial gauge holder can be swivelled 360. No. 34120 with prismatic base and additional adhesive surfaces on both sides. Dial gauge holder can be swivelled to all sides. The prismatic base also facilitates use as a shaft alignment device. Number 34100 34110 34120 Overall height mm 60 45 57 Ø of the round foot mm 46 Length x width of the contact face mm 72 x 37,5 70 x 35 Ø of the two sintered magnets, each mm 30 Adhesion force** approx. N 130 180 180 Ident. No. 010 010 010 Dial gauge holder without a dial gauge O. R. O. R. of 50 mm. Lever gauges see No. 33340-33370 page 794. Prod. Gr. 331 No. 34100 No. 34110 No. 34120 Measuring stand with guide rails cast iron foot with prismatic base (support and lateral faces fine ground) transverse arm with fine adjustment and Ø 8 mm hole for dial gauges, precision pointers or electronic length measuring probes Application: Optimal for parallelism inspections on measuring and control plates, since the ground V-groove and side faces of the foot can be used as precise stop or guide surfaces. The stand column can be moved inside the T clamping groove and clamped in the best position for each measurement. Measuring height mm 300 Overall height / columns Ø mm 335/16 Overhang / measuring arm Ø mm 180/16 Length x width x height of the foot mm 250 x 60 x 35 Prism angle at foot Approx. 90 T-guide and clamping slot on the foot mm 14,1 34001 Ident. No. 010 h Dial gauges see from No. 33000 page 779 Prod. Gr. 345 250 or 400 mm with measuring arms or measuring height 350 mm on request. Delivery without dial gauge Edition 5 821

Small magnetic measuring stand with round permanent magnetic feet the adjustable and swivelling joint system is chrome-plated. the combo-clamping piece holds display units with 8 mmø step and dovetail Application: especially suitable for use with lever gauges and small dial gauges. Overall height mm 155 Column Ø x length mm 8 x 110 Measuring arm Ø x length mm 8 x 60 Ø x height of the magnetic foot mm 35 x 42 Adhesion force** N 220 34130 Ident. No. 021 of 50 mm. Prod. Gr. 301 h Lever gauges see No. 33310-33370 page 793. Magnetic measuring stand switching magnet with prismatic base the combo-clamping piece holds display units with 8 mmø step and dovetail. Overall height approx. mm 240 Stand column (with an M 8 thread) length x Ø approx. mm 180 x 12 Magnetic foot, length x width x height approx. mm 58 x 50 x 65 Adhesion force** approx. N 650 34160 Ident. No. 011 of 50 mm. Prod. Gr. 301 Magnetic measuring stand cross joint, can be rotated and swivelled through 360 extremely high clamping force in the joints microfine adjustment made of steel with combined holder for dial gauges, precision pointer and electronic length measuring probe with shank Ø 8 mm and a lever gauge with a dovetail holder. switching magnet with prismatic base Overall height mm 290 Overhang mm 190 Rod Ø mm 16 Magnetic feet L x W x H mm 70 x 46 x 65 Adhesion force: round parts clamped in the Vee block /on the surface N 650 34165 Ident. No. 010 822 Edition 5

Measuring tables Magnetic measuring stand switching magnet with prismatic base, adheres to all plane steel and cast iron surfaces in any position. transverse holder with fine adjustment and adapter hole Ø 8 mm for dial gauges, precision pointers and electronic length measuring probes Total height of the instrument mm 285 Length of the stand column with the thread M 10/column Ø mm 228/16 Overhang of the measuring arm/measuring arm Ø mm 180/16 Magnetic base with M 10 adapter thread: Length x width x height mm 70 x 45 x 65 Adhesion force** approx. N 600 Ident. No. 010 34170 Complete stand without a dial gauge 34171 Wooden box for stand 34172 Magnetic foot without a stand column and without a transverse holder 34173 Complete transverse holder with a cross piece 34174 Stand column with an M 10 thread Spare parts for measuring stand No. 34170s Prod. Gr. 345 34175 34175 Part No. Designation Ident. No. U. pr. E Part No. Designation Ident. No. U. pr. E 1 Holder 010 O. R. 8 Clamp holder 080 O. R. 2 Star handle screw 020 O. R. 9 Spring 090 O. R. 3 Ball 025 O. R. 10 Star handle screw 100 O. R. 4 a* Articulated part for a ball-andsocket-joint 040 O. R. 11 Spherical disc 110 O. R. 4 b* Articulated part for a rocker 045 O. R. 12 Clamping bolt 120 O. R. joint 5 Split washer 050 O. R. 13 a* Transverse support for a balland-socket-joint 130 O. R. 6 a* Setscrew for a ball-and-socketjoint 060 O. R. 13 b* Transverse support for a rocker joint 135 (O. R.) 6 b* Setscrew for a rocker joint 065 O. R. 14 Disc 140 O. R. 7 Clamping piece 070 O. R. 17 Star grip 170 O. R. *Note design: Fine adjustment link with balls or with a rocker. Prod. Gr. 345 Delivery without dial gauge * * * The parts shown combine to create the complete transverse holder with a cross-piece No. 34173 Magnetic measuring stands with flexible column (Swan neck) With fine adjustment This stand is especially suitable for measuring places hard to reach. Central clamping with eccentric clamping lever, the tensioning rope can be tightened Switching magnet with flat and prismatic support surface. Overall height with link arm stretched mm 380 Ø of intermediate sleeves mm 17 Number of intermediate sleeves 6 Number of balls 7 Length x width x height of the magnet foot mm 70 x 46 x 65 Adhesion force** approx. N 500 34185 With fine adjustment Ident. No. 010 Small measuring stands table: hardened, ground and lapped holder for dial gauges and precision pointers Ø 8 mm column hardened and ground No. 34250 the round table is permanently supported on the cast iron foot with a rigid arm without fine adjustment. No. 34270 Table area with dust slots, transverse arm horizontally adjustable, without fine adjustment. Number 34250 34270 Measuring height:/total height mm 100/210 150/260 150/290 Table area mm Ø 50 60 x 68 98 x 115 Flatness tolerance of the table area m 2 2 4 Overhang mm 49 90 130 Columns Ø mm 22 22 28 Adapter hole for a dial gauge or precision pointer mm 8 8 8 Ident. No. 100 100 200 O. R. O. R. Prod. Gr. 301 No. 34250 100 No. 34270 100 Edition 5 823

Measuring tables Small measuring stands with threaded spindle table: can be aligned on 3 points, flatness tolerance of table areas 3 m hardened and ground column with thread and setting ring for exact positioning of the measuring arm to the correct height holder for dial gauges and precision pointers Ø 8 mm Measuring height:/total height approx. mm 140/300 150/300 Table version Natural stone Hardened steel with dust slots Table area approx. mm 100 x 100 95 x 95 Overhang approx. mm 85 85 Columns Ø mm 35 35 34272 Ident. No. 011 021 O. R. Measuring tables made of natural stone Prod. Gr. 301 measuring table made of natural stone evenness tolerance of measuring table according to DIN 876 accuracy level 00 hard chrome-plated column, with steep thread and setting ring for exact height setting holder for dial gauges, precision pointers or electronic length measuring probes with shank Ø 8 mm No. 34310 with rigid arm No. 34312 with parallel fine adjustment No. 34314 with movable transverse arm Measuring table L x W x H mm 240 x 140 x 50 300 x 210 x 60 400 x 300 x 70 Flatness tolerance of the table area m 3 3 3 Overall height mm 280 360 450 Columns Ø mm 35 35 35 Ident. No. 010 020 030d Measuring height mm 130 200 260 Overhang mm 70 100 120 34310 With rigid arm (O. R.) (O. R.) Measuring height mm 135 235 265 Overhang mm 70 100 120 34312 With parallel fine adjustment O. R. (O. R.) Measuring height mm 165 260 300 Overhang mm 160 225 270 34314 With adjustable cross arm O. R. O. R. d = Delivered ex works, postage and packaging excluded. Prod. Gr. 301 Ident. No. 011 Ident. No. 021 No. 34310 No. 34312 No. 34314 Place table stand made of natural stone, black The measuring face of the table top surface is particularly finely ground and lapped to an accuracy level of 00 in accordance with DIN 876. Adapter hole for display devices or electronic probes with an 8 mm shank.øthe cross arm with integrated fine adjustment can be turned, tilted exceeding the cross piece, it can be shifted horizontally and can be clamped with one turn. Delivery: without precision pointer, with test report. Column height mm 300 Table area mm 300 x 200 Flatness tolerance of the table area m 2,5 Plate thickness mm 50 Overhang mm 230 Columns Ø mm 18 Transverse arm Ø mm 16 Weight Kg 7,5 34295 Ident. No. 011d Prod. Gr. 341 Delivery without precision pointer 824 Edition 5