You can read the recommendations in the user guide, the technical guide or the installation guide for VALEX SP9217X. You'll find the answers to all your questions on the VALEX SP9217X in the user manual (information, specifications, safety advice, size, accessories, etc.). Detailed instructions for use are in the User's Guide. User manual VALEX SP9217X User guide VALEX SP9217X Operating instructions VALEX SP9217X Instructions for use VALEX SP9217X Instruction manual VALEX SP9217X You're reading an excerpt. Click here to read official VALEX SP9217X user guide http://yourpdfguides.com/dref/3226332
Manual abstract: valex.com Specification Number SP-9217 Valex High Purity Ball Valve SECTION 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9. 0 10.0 11.0 DESCRIPTION PAGE Scope......2 Reference Documents. 2 Material Characteristics...2 Operating Data..
3 Final Process 4 Testing and Inspection 4 Packaging
4 Marking and Documentation 5 Supplementary Features...5 Ordering Part Number System.. 6 Revision Log
8 This document is presented by Valex Corp. for general information purposes and may be reproduced in part or total. In total, the document reflects the specification requirements met or exceeded by Valex products sold under the name "Valex High Purity Ball Valve". SP-9217 Rev. X, Page 1 of 8 1. 0 Scope: Configuration: Sizes: Ball valve. 1/4" o.d. to 6" o.d. (6.4mm o.d. to 152.4mm o. d.) JIS 15A to 100A pipe (21.7mm o.d. @@@@@@TP-410 Flow of Fluids CGA G-4. 1, Cleaning Equipment for Oxygen Service. ANSI/ASQC Z1.4-1993 Sampling Procedures and Tables for Inspection by Attributes 3.0 Material Characteristics: ASTM Reference: Body Housing: ASTM A351-CF8M. End-Cap Flanges: ASTM A351-CF3M. Ball: ASTM A351-CF3M or A479 316/316L Wetted Path: CF3M / 316 stainless / 316L stainless. Non-Wetted: CF8M, 300-series stainless steel, vinyl (handle sleeve), tamper-evident ink (on bolt threads). Standard seats/seals: Reinforced Teflon (RTFE) seats, virgin Teflon (PTFE) seals. Other seat/seal materials are available. Materials of Construction: Internal Surface Roughness Wetted Path: Assembled Length Tolerance: Lubricant: 25 micro-inch maximum. Per brochure ±.25" (± 6.35mm) None SP-9217 Rev. X, Page 2 of 8 4.0 Operating Data: Temperature Range: -20 F to 350 F as dictated by standard seat/seal materials. Seat/seal materials other than standard may affect the working temperature range. Maximum Working Pressure: Temp (F) 1/4" - 1" 15A -20 1000 0 1200 1000 100 1000 350 1100 0 1-1/2" - 2" 20A - 40A 800 800 800 0 Pressure (PSIG) 2-1/2" - 4" 4.5" 6" Maximum Working Pressure 50A - 80A 100A (PTFE Seats / Seals ) 500 400 300 500 400 300 500 400 300 0 0 0 6" 100A 2-1/2" - 4" (50A - 80A) 1000 900 800 1-1/2" - 2" (20A - 40A) 1/4" - 1" (15A) Pressure (PSIG) 700 600 500 400 300 200 100 0-50 0 50 100 150 200 250 300 350 400 Temperature ( F) Flow Coefficient Data: Valve Size 1/4" X.035" 3/8" X.035" 1/2" X.049" 3/4" X.065" 1" X.065" 1-1/2" X.065" 2" X.065" 2-1/2" X. 065" 3" X.065" 4" X.083" 6" X.109" JIS 15A (5S) JIS 20A (5S) JIS 25A (5S) JIS 32A (5S) JIS 40A (5S) JIS 50A (5S) JIS 65A (5S) JIS 80A (5S) JIS 100A (5S) 1) Ball Orifice (Inches) 0.402 0. 402 0.402 0.620 0.870 1.370 1. 870 2.370 2.870 3.834 5.782 0.870 1.370 1.370 1.870 1.870 2. 370 2.870 3.834 4.335 Connection Orifice (Inches) 0.180 0.305 0.402 0.620 0.870 1.370 1. 870 2.370 2.870 3.834 5.782 0. 724 0.941 1.209 1.551 1.783 2. 252 2.839 3.343 4.335 Cv1 2.9 9.0 16.3 41.2 84.9 223.3 432. 3 714.4 1071.2 1975.3 4697.8 57.4 100.4 171.1 290.7 391.0 641. 1 1046.5 1478.4 2559.3 Flow coefficient data calculated using methods described in Crane Technical Paper TP-410. SP-9217 Rev. @@@@@@@@Flow path i.d. @@@@@@@@@@Leak tests are performed using 99.995% helium. Assembled valves are tested in a Class 100 environment. @@@@Plug Option: Metal threaded plug. @@6" (152.4mm) Tube Stub: Vinyl cap. @@@@Packaged for shipment in a manner that prevents damage to product and primaryproduct packaging. Shipping Container: 8.0 Marking and Documentation: Marking and Traceability: All components are traceable to the producing mill and heat number by a metalstamped code number. Each valve is pin-stamped with a Valex work-order i.d. number. Each assembly's bag is affixed with a label identifying the assembly's part number and process date. Certificate of compliance to this specification. Labeling: Documentation: 9.0 Supplementary features: The features listed in sections 1 through 8 describe the minimum specifications for the Valex ball valve identified by the letter "M" as the sixteenth character in the part number as shown on the table in section 10. The following supplementary features are available at extra cost by replacing that "M" with the letter preceding the desired features. E: - Electropolished i.d. to 10 micro-inch (.25 micro-meter) Ra maximum. - Assembled Length Tolerance: Per brochure ±.125" (± 3. 175mm) - Inboard helium leak tested to 8 x 10-9 atm cc/sec. - Across-the-seat helium leak tested to 5.8 x 10-9 atm cc/sec. - Mechanically polished i.d. to 20 micro-inch (.51 micro-meter) Ra maximum. - All other features same as "E" above - Assembled with Oxygen-compatible lube - All other features same as "E" above. - Assembled with Oxygen-compatible lube - All other features same as "N" above. N: L: P: SP-9217 Rev. X, Page 5 of 8 10.0 Ordering Part Number System: NOTE: Not all possible part number combinations are available. @@x.035" wall 06 = 3/8" o.d. x.035" wall 08 = 1/2" o.d. x.049" wall B8 = 1/2" o. d. x.065" wall 12 = 3/4" o.d. x.065" wall 16 = 1" o.d. x.065" wall 24 = 1-1/2" o.d. x.065" wall 32 = 2" o.d. x.065" wall 40 = 2-1/2" o. d. x.065" wall 48 = 3" o.d. x. 065" wall 64 = 4" o.d. x.083" wall 96 = 6" o.d. @@@@X, Page 6 of 8 NOTE: Not all possible part number combinations are available. Please contact Valex for availability. JIS PIPE SIZES S - STR 40 A - XX X S S - M B Material S = Stainless Steel Assembly Pattern STR = straight DHC = double horizontal cross SHC = single horizontal cross DHT = double horizontal tee DVT = double vertical tee DAV = double angle valve DSS = double single sided Main
Powered by TCPDF (www.tcpdf.org) Tube Size 15A = 21.7mm o.d. x 1.65mm wall 20A = 27.2mm o.d. x 1.65mm wall 25A = 34.0mm o.d. x 1.65mm wall 32A = 42. 7mm o.d. x 1.65mm wall 40A = 48.6mm o. d. x 1.65mm wall 50A = 60.5mm o.d. x 1.65mm wall 65A = 76.3mm o.d. x 2.10mm wall 80A = 89.1mm o.d. x 2.10mm wall 100A = 114. 3mm o.d. x 2.10mm wall Main Tube Connections A = pipe buttweld inlet and outlet Branch Valve(s) Outlet Size X X = no branch valve(s) 15A 20A 04 = 1/4" 25A 06 = 3/8" 32A 08 = 1/2" 40A 12 = 3/4" 50A 16 = 1" 65A 24 = 1-1/2" 80A 32 = 2" Handle Sleeve Color B = blue P = purple D = gold R = red G = green S = silver I = pink W = white K = black Y = yellow Section 9.0 Identifier E = 10 Ra electropolished / no lube L = 10 Ra electropolished / oxygencompatible lube M = 180grit or 25Ra / no lube N = 20 Ra mechanical polished / no lube P = 20 Ra mechanical polished / oxygen-compatible Outlet Purge Port* X = no purge port C = compression fitting D =. You're reading an excerpt. Click here to read official VALEX SP9217X user guide http://yourpdfguides.com/dref/3226332