B12 Tilt-turn windows B12.12 salto safe 4128 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. 32 9 388 88 81 - F. 32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com
salto safe 4128 Contents 1. General characteristics... B12.12.03 2. Base set n 4028 in combination with SALTO 4108... B12.12.04 3. Vertical centre locking sets n 4028-30, 4028-31... B12.12.05 4. Horizontal centre locking sets n 4028-34, 4028-35... B12.12.06 5. Reinforcement set n 35140-790... B12.12.07 6. Handles... B12.12.08 7. Ordering tables... B12.12.09 8. General information... B12.12.10 b12.12.02
salto Safe 4128 1. General characteristics To make your windows extra secure against burglary, you should use the high security system SALTO SAFE 4028 in combination with the standard tilt-turn system SALTO 4108. The following sets are used dependent on the window dimensions: base set n 4028 for: vent width Fb=590-899 mm and vent height Fh=900-1199 mm....... page B12.12.04. vertical centre locking set n 4028-30 for vent height Fh=1200-1799 mm.. page B12.12.05. vertical centre locking set n 4028-31 for vent height Fh=1800-2400 mm.. page B12.12.05. horizontal centre locking set n 4028-34 for vent width Fb=900-1199 mm.. page B12.12.06. horizontal centre locking set n 4028-35 for vent width Fb=1200-1700 mm.. page B12.12.06. The set contains the following high security parts: stainless steel mushroom head bolts pre-riveted to zinc alloy connection pieces, which are connected to the SALTO components and rods in the vent section. zinc alloy security wedges which are fixed on the frame section with clamping plates and self-drilling screws. protection pieces close to the handle and bottom bolt. The reinforcement set n 35140-790 must always be installed (see page B12.12.07). The high security set should always be operated by a cylinder locking handle, available in 4 types (see page B12.12.08). For windows with vent width Fb=1400-1700 mm you must install the additional arm n 4008-360. The additional arm provides greater stability, especially for wide and heavy windows in tilt position. The additional arm is non-handed. All parts are made of non-corroding materials. Size range: vent width: 590-1700 mm vent height: 900-2400 mm vent weight: max. 130 kg ratio of vent width Fb / vent height Fh = max. 1.5 Special dimensions on request! This system is suitable for sections with frame groove width of 14 mm. See drawing. b12.12.03
salto safe 4128 2. Base set n 4028 in combination with SALTO 4108 Vent width Fb = 590-899 mm Vent height Fh = 900-1199 mm X = Fb-368 (4108A without 4010-344A.. when Fb=540-590) X = Fb-503 (4108A) X = Fb-660 (4108B) For a left window: cut off piece n 4000-189 4108A or 4108B SALTO SAFE 4028 2 4000-355 corner transmission 3 4010-344A locking point 1 4010-344B locking point 1 4010-344C locking point 1 4010-344E locking point 1 4020-232B connection piece 10 4020-233 nut 3 4020-325B safety piece 1 4020-345 locking point 1 4020-346 connection piece 1 4028-182 thickness piece 7 30310-840 wedge 10 M5x12 screw DIN 965 Installation high security wedge n 30310-840 Slide in clamping plate before the assembly of the frame Screw the plate to the wedge Screw the wedge after positioning b12.12.04
salto Safe 4128 3. Vertical centre locking sets n 4028-30, 4028-31 Vent height Vent height Fh = 1200-1799 mm Fh = 1800-2400 mm or 4028 4028-30 1 4000-334 locking point 1 4000-345 locking point 2 4008-184 wedge 1 4010-344A locking point 1 4010-344C locking point 1 4020-346 connection piece 2 30310-840 wedge 4028 4028-30 4028-31 1 4000-334 locking point 1 4000-345 locking point 2 4008-184 wedge 1 4010-344A locking point 1 4020-345 locking point 3 4020-346 connection piece 2 30310-840 wedge b12.12.05
salto safe 4128 4. Horizontal centre locking sets n 4028-34, 4028-35 Vent width Fb = 900-1199 mm 4028 4028-34 1 4010-344C locking point 1 30310-840 wedge Vent width Fb = 1200-1399 mm 4028 4028-34 4028-35 1 4000-334 locking point 2 4008-184 wedge 1 4010-344A locking point 1 30310-840 wedge b12.12.06
salto Safe 4128 Vent width Fb = 1400-1700 mm 4028 4028-34 4028-35 1 4000-334 locking point 2 4008-184 wedge 1 4010-344A locking point 1 30310-840 wedge additional arm 4008-360 In combination with the SALTO 4108B, the high security set is installed together with the additional arm n 4008-360 for windows with vent width Fb = 1400-1700 mm. 5. Reinforcement set n 35140-790 For high security windows you must reinforce the top hinge with the reinforcement set n 35140-790. The M4x10 thread forming screws must fix into at least 6 mm of aluminium. Drilling jig n 35000-955 is available for drilling the holes. Reinforcement set n 35140-790 1 35140-790-1 reinforcement piece 2 30140-790-2 screw b12.12.07
salto safe 4128 6. Handles throw X = 34 mm throw X = 34 mm n 4000-219 CYL n The high security system must always be operated by cylinder locking handles n 4000-... CYL. The cylinder locking handle can be locked in closed or tilt position. The same handles can also be used for side hung windows. As a result, tilt-turn windows and side hung windows can be used next to one another with the advantage of having the same appearance. Finish: handle n 4000-219 CYL and n : grip in aluminium and base in zinc alloy, always polyester powder coated (more than 450 RAL colours). handle n 4000-215 CYL and n 4000-214 CYL: grip and base in aluminium anodised or polyester powder coated (more than 450 RAL colours). Fixing holes see page B12.11.11. throw X = 34 mm throw X = 34 mm n 4000-215 CYL n 4000-214 CYL b12.12.08
salto Safe 4128 7. Ordering tables Fb=590-749 Fb=750-899 Fb=900-1199 Fb=1200-1399 Fb=1400-1700 Fh = 900-1199 Fh = 1200-1799 Fh = 1800-2400 4108A 4108A -30-30 -30-31 -34-30 -34-30 -31-34 -34-35 -30-34 -35-30 -31-34 -35-34 -35 4008-360 -30-34 -35 4008-360 -30-31 -34-35 4008-360 Order example: A tilt-turn window with overall vent width (Fb) 1450 mm and overall vent height (Fh) 1600 mm in which glass has a thickness of 16 mm and a weight of 40 kg/m 2. Note: to determine the precise vent weight see page B12.12.10. Fittings to order: 1x 1x 4108B 1x 35140-790 1x 4028 1x 4028-30 1x 4028-34 1x 4028-35 1x 4008-360 b12.12.09
salto safe 4128 8. General information The high security system SALTO SAFE 4028 can be used within the Fh/Fb sizes and weight limitations indicated on the chart below. The ratio of the dimensions Fb/Fh must not exceed the value of 1.5. The handle height should not be less than 1/3 of the vent height. Technical advise should be sought when the sizes of your window are not shown in the chart. High security wedges must be fixed on the frame section with clamping plates and self-drilling screws. Stainless steel mushroom head bolts must be adjusted so that they run free within the security wedge. For heavy, wide windows and especially for vents over 1400 mm wide the additional arm is recommended for good stability of the window in the tilt position. High security wedges or High security system SALTO SAFE 4028 is made of noncorroding materials. The set should not be installed in corrosive atmospheres. Sobinco cannot be held responsible for the malfunctioning of the high security system SALTO SAFE 4028 if any non- Sobinco parts are used. Surface treatment of vent and frame must take place before assembly of the set, as this will affect the working of the gear. Glazing must be in accordance with national standards. The window and gear should be kept clean and lubricated in accordance with our maintenance instructions (copy available on request). Glass thickness without air gap Vent height Fh Vent width Fb max. 130 kg mm kg/m² 10 25 12 30 14 35 16 40 18 45 20 50 22 55 24 60 26 65 28 70 30 75 32 80 34 85 36 90 38 95 40 100 42 105 b12.12.10