DOOR HINGES
Contents Full Mortise Hinges Heavy Weight For Interior Doors....3 For Exterior Doors.... Standard Weight For Interior Doors....,.7 For Exterior Doors....6 Electrified....8 Spring Hinge....9 Cam-Lift Hinge.... Startec For Interior Doors....11 Receiving Elements....12 Drilling Jig and Bit.....13 Tectus For Interior Doors....1-.20 Mounting Plates....21 Receiving Elements....22 Routing Templates and Drilling Jig....23 Concealed Mortise Mounted Power Transfer Device....2 Concealed Jamb Door Closer Perko-Power....2 Perko....26 Perkomatic....26 AH.2 www.hafele.com
Full Mortise Hinge www.hafele.com AH.3 1/1
Full Mortise Hinge 1/1 AH. www.hafele.com
Full Mortise Hinge www.hafele.com AH. 1/1
Full Mortise Hinge 1/1 AH.6 www.hafele.com
Full Mortise Hinge www.hafele.com AH.7 1/1
Full Mortise Hinge Electrified - Standard Weight For openings where electricity travels from the frame to hardware installed on the door leaf Ball bearing Square corners Non handed ANSI/BHMA A16.7 11 ( 1/2") 3. (.13") Ø1 (Ø19/") 6 (2 9/16") 8 (1 29/") 11 ( 1/2") Model # HB128 Knuckles: Bearings: 2 Pin: Non-Removable Version: 8 Electric through-wires Electrical rating: Wire: up to VDC, 3. Amps continuous, 1 Amps pulse Switch: up to 3 VDC at. Amps Flange thickness: 3. mm (.13 ) W x H: 11 x 11 mm ( 1/2 x 1/2 ) Material: Steel Finish 600 prime coated (USP) 926.0.00 6 brass plated, polished (US3) 926.0.01 633 brass plated, satin (US) 926.0.02 61 bronze plated, oxidized & lacquered (USB) 926.0.03 61 chromium plated, polished (US26) 926.0.0 62 chromium plated, satin (US 26D) 926.0.0 Supplied With Wood screws Machine screws Note Not recommended for doors with closing devices. Additional sizes and finishes are available - Please contact Häfele for details. AH.8 www.hafele.com
Full Mortise Spring Hinge www.hafele.com AH.9 1/1
Full Mortise Cam-Lift Hinge Standard Weight Cam-lift hinges greatly improve the sealing characteristics along the door perimeter Works well as replacement hinge where doors drag Rounded corners Handed 1 (9/16") 3. (.13") 11 ( 1/2") 11 ( 1/2") 7 (1 27/") 3 Model # HB11 Knuckles: 2 Version: Cam-lift Weight Bearing: Up to 300 lbs. door with 3 hinges Lift: 1/8 (3 mm) over 90, maximum lift 1/ (6 mm) over 180 Flange thickness: 3. mm (.13 ) W x H: 11 x 11 mm ( 1/2 x 1/2 ) Material: Stainless Steel Finish Handing 629 stainless steel, polished (US) right 926.0.068 629 stainless steel, polished (US) left 926.0.069 Supplied With Wood screws Machine screws Note Additional sizes and finishes are available - Please contact Häfele for details. AH. www.hafele.com
For Interior Doors StarTec For flush interior wood doors - 3D Adjustable Suitable for left-hand or right-hand installation H2 9 (3 3/") Door weight: kg (99 lbs.) with 2 hinges 60 kg (1 lbs.) with 3 hinges Opening angle: 180º Door width: 900 mm ( 3 7/16 ) Door height: 2000 mm ( 78 3/ ) 20 mm ( 82 11/16 ) use hinges Door thickness: mm (1 1/ ) Adjustability: Continuously three dimensional adjustable Height ± 2. mm (3/ ), Lateral +3 mm/-2 mm (+1/8 /-1/16 ) On contact ± 1 mm (1/ ) Mounting 23.3 (1/16") Material: Zinc Die-cast Finish satin chrome 927.91. satin nickel 927.91.6 gold polished 927.91.8 23.3 (1/16") 31 (1 3/16") 31 (1 3/16") 3 900 ( 3 7/16") 3 Note When using the receiving element the milling dimensions may change. 2 (1") 9 (3 3/") 60 (2 3/8") 23.3 (1/16") H7 Photo depicts LH or RH reverse. Mounting 20 (2/") 29 (1 /") (/") 6 (1/") 6 (1/") 0 (1 9/16") 900 (3 7/16") (/") 112 ( 3/8") 91 (3 19/") 29 29 (1 /") (1 /") 1.6 (/8") 6 (1/") 31 Door weight: 0 kg (1 lbs.) with 2 hinges 70 kg (1 lbs.) with 3 hinges Opening angle: 180º Door width: 900 mm ( 3 7/16 ) Door height: 2700 mm ( 8 /16 ) 200 mm ( 7 1/2 ) use hinges Door thickness: 0 mm (1 9/16 ) Adjustability: Continuously three dimensional adjustable Height ± 3.0 mm (1/8 ), Lateral +3 mm/-2 mm (+1/8 /-1/16 ) On contact ± 1 mm (1/ ) Material: Zinc Die-cast Finish Item No satin chrome 927.91. satin nickel 927.91.6 gold polished 927.91.8 Note When using the receiving element the milling dimensions may change. 112 ( 3/8") 70 (2 3/") 29 (1 /") www.hafele.com AH.11 1/1
StarTec H2 and H7 Suitable for left-hand or right-hand installation 6 (2 3/16") Receiving Element For H2 133 ( 1/") For concealed hinge H2 installed into a wood door frame Material: Zinc Die-cast 927.91.90 19 (3/") Note When using the receiver the milling dimensions may change. Mounting Trim 3 Door 6 (2 3/16") Receiving Element For H7 For concealed hinge H7 installed into a wood door frame Mounting Trim 1 ( 11/16") 3 7 (1/") Door Material: Zinc Die-cast 927.91.90 Note When using the receiver the milling dimensions may change. AH.12 www.hafele.com
StarTec H2 and H7 Hinge Jig For milling the cut-outs of concealed hinges H2/H7 Suitable for H2 927.91.903 H7 927.91.90 Supplied With 1 Bar 2 Routing templates Router Bit For milling of concealed hinges H2/H7 Router bit Ø: 12 mm (1/2 ) Suitable for H2 927.91.913 H7 927.91.91 3 (1 11/16") 90 (3 3/16") 12 (1/2") Ø12 (1/2") Ø www.hafele.com AH.13
For Interior Doors - Used in door frames made out of hollow metal or wood for flush doors Maintenance-free slide bearings Suitable for LH and RH applications TE 20 3D 18 (11/16") 11.7 (7/16") 21 (13/16") 1 (6 1/8") 27 (1 1/16") 9 Door weight: 0 kg (88 lbs.) Door thickness: 0 mm (1 9/16 ) Opening angle: 180º Router bit Ø: 16 mm (/8 ) Router guide Ø: 30 mm (1 3/16 ) Adjustment: three-dimensionally adjustable: Height and Width: ± 3 mm (1/8 ) Depth: ± 1. mm (1/16 ) Material: Aluminum Die-cast Finish stainless steel effect 92.17.00 satin chrome colored 92.17.021 satin nickel colored 92.17.022 black powder-coated 92.17.0 bronze powder-coated (USB look) 92.17.00 rustic umber colored 92.17.016 satin nickel plated 92.17.071 polished nickel plated 92.17.070 polished brass plated 92.17.068 Mounting 18 (11/16") 27 (1 1/16") 21 (13/16") 3. 2 27 (1/16") (1 1/16") 16 (/8") 18 (11/16") Mounted to a wood door frame 21 (13/16") 3 2 (1/16") 27 (1 1/16") 16 (/8") Mounted to a hollow metal frame with a receiver element 18 (11/16") 21 (13/16") 18 (11/16") 3 2 27 (1/16") (1 1/16") Mounted to a wood door jamb together with a mounting plate 16 (/8") 18 (11/16") 1 (6 1/8") 1 ( 3/16") 18 (3/") 3 21 (13/16") 16 (/8") 120 ( 3/") 12 ( 9/16") 1 (6 1/8") Milling template for a wood door frame 2 (1/16") 3 1 (9/16") Mounting plates page.21 Receiving elements page.22 2 ( 1/16") 1/1 AH.1 www.hafele.com
For Interior Doors - Used in door frames made out of hollow metal or wood for flush doors Maintenance-free slide bearings Suitable for LH and RH applications UL listed for 20 minute rated fire doors (maximum door size: x 8 for a single door, 8 x 8 for a pair of doors) TE 30 3D Door weight: 80 kg (176 lbs.) Door thickness: 0 mm (1 9/16 ) Opening angle: 180º Router bit Ø: 2 mm (1/16 ) Router guide Ø: 30 mm (1 3/16 ) Adjustment: three-dimensionally adjustable: Height and Width: ± 3 mm (1/8 ) Depth: ± 1.0 mm (1/16 ) 28 (1 1/8") 17. (11/16") 28 (1 1/8") 160 (6 /16") 3 (1 /16") 9 Material: Aluminum Die-cast Finish stainless steel effect 92.17. satin chrome colored 92.17.121 satin nickel colored 92.17.122 black powder-coated 92.17.1 bronze powder-coated (USB look) 92.17. rustic umber colored 92.17.116 satin nickel plated 92.17.171 polished nickel plated 92.17.170 polished brass plated 92.17.169 white powder-coated RAL 9016 92.17.177 Mounting 28 (1 1/8") 3 (1 /16") 28 (1 1/8") 28 (1 1/8") 3. 31 3. 31 38 ( 1 1/2") 33. (1 /16") 33. (1 /16") 28 (1 1/8") Mounted to a wood door frame 1 (1/16") Mounted to a hollow metal frame with a receiver element 28 (1 1/8") 28 (1 1/8") Mounting plates page.21 Receiving elements page.22 3. 31 33. (1 /16") Mounted to a wood door jamb together with a mounting plate 28 (1 1/8") 160 (6 /16") 138 ( 7/16") 131 ( 3/16") www.hafele.com AH.1 1 (9/16") 28 (1 1/8") 138 ( 7/16") 160 (6 /16") Milling template for a wood door frame 31. Calculation of the milling dimensions: A = Rabbet depth excluding seal clearance B = Door thickness A B + 3 = Dimension X The result has to fall between 3 mm (1/8 ) and maximum mm (3/16 ). For hollow metal frame applications X = mm (3/16 ) 1/1
- TE 26 3D and TE 27 3D Used in door frames made out of hollow metal or wood for flush doors Maintenance-free slide bearings Suitable for LH and RH applications UL listed for minute rated fire doors 9 Door weight: 120 kg (26 lbs.) Door thickness: 3 mm (1 3/8 ) Opening angle: 180º Router bit Ø: 19 mm (3/ ) Collar ring Ø: 2. mm (1 ) Adjustment: three-dimensionally adjustable: Height and Width: ± 3 mm (1/8 ) Depth: ± 1.0 mm (1/16 ) 1 (6 1/8") TE 26 3D Material: Stainless Steel; Finish: satin TE 27 3D Material: Steel; Finish: stainless steel look 92.16.803 26 (1") 1 26 (19/") (1") 33 (1 /16") 92.19.030 Mounting (/") 12 (1/2") 33 (1 /16") 26 (1") 1 (1 /8") 26 (1") AH.16 33 (1 /16") 3. 33 (1 /16") (1 1/") 3. (1 1/") 26 (1") (/") Mounted to a wood door frame Mounted to a hollow metal frame with a receiver element 26 (1") (/") 26 (1") 33 (1 /16") 3.. (1 1/") Mounted to a wood door jamb together with a mounting plate 26 (1") (/") 11 ( 1/2") 26 (1") (1/2") (/") 2 (") 1 (6 1/8") Milling template for a wood door frame. (1 1/") (/") 6 (1/") Mounting plates page.21 Receiving elements page.22 www.hafele.com
For Interior Doors - Used in door frames made out of hollow metal or wood for flush doors Maintenance-free slide bearings Suitable for LH and RH applications UL listed for 20 minute rated fire doors (maximum door size: x 8 for a single door, 8 x 8 for a pair of doors) TE 0 3D 16. (/8") 200 (7 7/8") 3 (1 /16") 9 Door weight: 120 kg (26 lbs.) Door thickness: 0 mm (1 9/16 ) Opening angle: 180º Router bit Ø: 2 mm (1/16 ) Router guide Ø: 30 mm (1 3/16 ) Adjustment: three-dimensionally adjustable: Height and Width: ± 3 mm (1/8 ) Depth: ± 1.0 mm (1/16 ) Material: Aluminum Die-cast Finish stainless steel effect 92.17.20 satin chrome colored 92.17.221 satin nickel colored 92.17.222 black powder-coated 92.17.2 bronze powder-coated (USB look) 92.17.20 rustic umber colored 92.17.216 satin nickel plated 92.17.271 polished nickel plated 92.17.269 polished brass plated 92.17.281 Mounting 36. 200 (7 7/8") 170 (6 11/16") 17 (6 3/16") 18 (11/16") 19 (3/") 17 (6 3/16") 170 (6 11/16") 200 (7 7/8") 3. 3 (1 3/8") 3. 3. (1 3/8") 2 ( 1 /8") 3 (1 3/8") 36. 3 (1 3/8") 36. Mounted to a wood door frame 1 (1/16") Mounted to a hollow metal frame with a receiver element Mounting plates page.21 Receiving elements page.22 3. 3 (1 3/8") 3. 36. (1 3/8") Mounted to a wood door jamb together with a mounting plate www.hafele.com AH.17 Milling template for a wood door frame 3. (1 3/8") Calculation of the milling dimensions: A = Rabbet depth excluding seal clearance B = Door thickness A B + 3 = Dimension X The result has to fall between 3 mm (1/8 ) and maximum mm (3/16 ). For hollow metal frame applications X = mm (3/16 ) 1/1
For Interior Doors - Used in door frames made out of hollow metal or wood for flush doors with an additional up to 8 mm (/16 ) thick surface applied panel Maintenance-free slide bearings Suitable for LH and RH applications UL listed for 20 minute rated fire doors (maximum door size: x 8 for a single door, 8 x 8 for a pair of doors) TE 0 3D A8 Door weight: 0 kg (220 lbs.) Door thickness: 0 mm (1 9/16 ) Opening angle: 180º Router bit Ø: 2 mm (1/16 ) Router guide Ø: 30 mm (1 3/16 ) Adjustment: Three-dimensionally adjustable: Height and width: ± 3 mm (1/8 ) Depth: ± 1.0 mm (1/16 ) 2. (1") 200 (7 7/8") 9 3 (1 /16") 27 (1 1/16") Material: Aluminum Die-cast Finish stainless steel effect 92.17.30 satin chrome colored 92.17.1 satin nickel colored 92.17.2 black powder-coated 92.17.3 bronze powder-coated (USB look) 92.17.30 satin nickel plated 92.17.1 polished nickel plated 92.17.369 polished brass plated 92.17.380 3. (1 11/16") Mounting 200 (7 7/8") 170 (6 11/16") 17 (6 3/16") 18 (11/16") 19 (3/") 17 (6 3/16") 170 (6 11/16") 200 (7 7/8") 92 (3 /8") 1/1 8 (/16") 8 (/16") AH.18 1 (1 /8") 3. 1 (1 /8") 3. 8 ( 1 7/8") 1 (1 /8") 3. (1 11/16") Mounted to a wood door frame 1 (1 /8") 3. (1 11/16") Mounted to a hollow metal frame with a receiver element 8 (/16") 8 (/16") 8 (/16") 1 (1 /8") 3. 1 (1 /8") 3. (1 11/16") Mounted to a wood door jamb together with a mounting plate 8 (/16") Milling template for a wood door frame 1. (1 /8") Mounting plates page.21 Receiving elements page.22 www.hafele.com
For Interior Doors - Used in door frames made out of hollow metal or wood for flush doors Maintenance-free slide bearings Suitable for LH and RH applications UL listed for 20 minute rated fire doors (maximum door size: x 8 for a single door, 8 x 8 for a pair of doors) TE 60 3D 16. (/8") 20 (9 7/16") 9 3 (1 /16") Door weight: 200 kg (0 lbs.) Door thickness: 0 mm (1 9/16 ) Opening angle: 180º Router bit Ø: 2 mm (1/16 ) Router guide Ø: 30 mm (1 3/16 ) Adjustment: three-dimensionally adjustable: Height and Width: ± 3 mm (1/8 ) Depth: ± 1.0 mm (1/16 ) Material: Aluminum Die-cast Finish stainless steel effect 92.17.0 satin chrome colored 92.17.21 satin nickel colored 92.17.22 black powder-coated 92.17. bronze powder-coated (USB look) 92.17.0 satin nickel plated 92.17.71 polished nickel plated 92.17.69 polished brass plated 92.17.80 36. Mounting 18 (11/16") 19 (3/") 20 (9 7/16") 2 (8 1/") 197 (7 3/") 197 (7 3/") 2 (8 1/") 20 (9 7/16") 3. 3 (1 3/8") 3. 3. (1 3/8") 2 (1 /8") 3 (1 3/8") 36. 3 (1 3/8") 36. Mounted to a wood door frame 1 (1/16") Mounted to a hollow metal frame with a receiver element Mounting plates page.21 Receiving elements page.22 3. 3. (1 3/8") 3 (1 3/8") 36. Mounted to a wood door jamb together with a mounting plate www.hafele.com AH.19 Milling template for a wood door frame 3. (1 3/8") Calculation of the milling dimensions: A = Rabbet depth excluding seal clearance B = Door thickness A B + 3 = Dimension X The result has to fall between 3 mm (1/8 ) and maximum mm (3/16 ). For hollow metal frame applications X = mm (3/16 ) 1/1
For Interior Doors - Used in door frames made out of hollow metal or wood for flush doors with an additional up to 8 mm (/16 ) thick surface applied panel Maintenance-free slide bearings Suitable for LH and RH applications UL listed for 20 minute rated fire doors (maximum door size: x 8 for a single door, 8 x 8 for a pair of doors) TE 60 3D A8 Door weight: 160 kg ( lbs.) Door thickness: 0 mm (1 9/16 ) Opening angle: 180º Router bit Ø: 2 mm (1/16 ) Router guide Ø: 30 mm (1 3/16 ) Adjustment: three-dimensionally adjustable: Height and Width: ± 3 mm (1/8 ) Depth: ± 1.0 mm (1/16 ) 2. (1") 3 (1 /16") 20 (9 7/16") 9 3 (1 /16") Material: Aluminum Die-cast Finish stainless steel effect 92.17.0 satin chrome colored 92.17.21 satin nickel colored 92.17.22 black powder-coated 92.17. bronze powder-coated (USB look) 92.17.0 satin nickel plated 92.17.71 polished nickel plated 92.17.72 polished brass plated 92.17.80 (1/") (1 1/2") 3. (1 11/16") Mounting 20 (9 7/16") 2 (8 1/") 197 (7 3/") 18 (11/16") 19 (3/") 197 (7 3/") 2 (8 1/") 20 (9 7/16") 92 (3 /8") 16 (/8") 1/1 8 (/16") 8 (/16") AH.20 1 (1 /8") 3. 1 (1 /8") 3. 8 (1 7/8") 1 (1 /8") 3. (1 11/16") 1 (1 /8") 3. (1 11/16") 8 (/16") Mounted to a wood door frame Mounted to a hollow metal frame with a receiver element 8 (/16") 8 (/16") 1 (1 /8") 3. 1 (1 /8") 3. (1 11/16") Mounted to a wood door jamb together with a mounting plate 8 (/16") Milling template for a wood door frame 1. (1 /8") Mounting plates page.21 Receiving elements page.22 www.hafele.com
Mounting Plates Suitable for concealed hinges TE 20/30/2/0/60 3D and TE 0/60 3D A8 mounted into wood door jambs Suitable for left-hand and right-hand installations 80 (3 1/8") 80 (3 1/8") 70 (2 3/") 70 (2 3/") 80 (3 1/8") 239. (9 7/16") 200 (7 7/8") 160 (6 /16") 12 ( 7/8") 160 (6 /16") 127 (") 180 (7 1/16") 3. 3 ( 1/16") 16 (6 1/8") 196. (7 3/") TE 20 3D FZ/1 TE 30 3D FZ/1 TE 2 3D FZ/1 TE 0 3D FZ/1 TE 60 3D FZ/1 18 (7 /16") 80 (3 1/8") TE 1 3D FVZ FZ/1 1 (6 1/8") hinges pages.1-.20 Material: Steel, galvanized Model TE 20 3D FZ/1 92.17.098 TE 30 3D FZ/1 92.17.198 TE 2 3D FZ/1 for TE 26 3D and TE 27 3D 92.0.983 TE 0 3D FZ/1 92.17.298 TE 60 3D FZ/1 92.17.98 TE 1 3D FVZ FZ/1 92.19.027 Supplied With Mounting plate 2 Spacer plates per 0., 1, 2, 3 mm Note TE 2 comes without 0. mm spacer plates www.hafele.com AH.21 1/1
Receiving Elements - For TE 20/30/26/27/0/60 3D/3D A8 and 1 3D FVZ mounted onto hollow metal frames Suitable for left-hand and right-hand installations Material: Steel, galvanized Model A B TE 20 3D SZ 20 (8 1/16 ) 26 (1 ) 92.17.099 TE 30 3D SZ 2 (8 1/ ) 3 (1 /16 ) 92.17.199 TE 26 3D SZ 20 (8 1/16 ) 3. (1 /16 ) 92.0.083 TE 27 3D SZ 20 (8 1/16 ) 3. (1 /16 ) 92.0.083 TE 0 3D SZ 28 (9 3/ ) 38 (1 1/2 ) 92.17.299 TE 0 3D A8 SZ 20 (9 13/16 ) 3 (1 11/16 ) 92.17.799 TE 1 3D FVZ SZ 23 (9 1/ ). (1 3/ ) 92.19.028 TE 60 3D SZ 288 (11 1/16 ) 38 (1 1/2 ) 92.17.99 TE 60 3D A8 SZ 290 (11 7/16 ) 3 (1 11/16 ) 92.17.899 27. (1 1/16") 21.8 (7/8") 2. 3.6 (1 3/8") 29 (1 1/8") 33. (1 /16") 3. (1 11/") 29 (1 /") 38. (1 1/2") 33 (1 /16") 38. (1 1/2") 33 (1 /16") 38. (1 1/2") 33 (1 /16") 38. (1 1/2") 33 (1 /16") 162 (6 3/8") TE 20 3D SZ 168 (6 /8") TE 30 3D SZ 16 (6 7/16") TE 26 3D SZ TE 27 3D SZ 192 (7 9/16") TE 1 3D FVZ SZ 208 (8 3/16") TE 0 3D SZ 208 (8 3/16") TE 0 3D A8 SZ 28 (9 3/") TE 60 3D SZ 28 (9 3/") TE 60 3D A8 SZ hinges pages.1-.20 AH.22 www.hafele.com 1/1
Routing Templates - For milling of TE 20/30/26/27/0/60 3D, 0/60 3D A8 and 1 3D FVZ Router bit Ø: 12.7 mm (1/2 ) for the TE 20 and 19 mm (3/ ) for all other models Collar ring Ø: 2. mm (1 ) for all other models Suitable for Jig for milling hinge into TE 20 3D door 922.1.662 jamb 922.1.661 TE 30 3D door and jamb, part 1 922.1.663 door and jamb, part 2 922.1.66 TE 26 3D TE 27 3D door and jamb 922.1.670 TE 0 3D door and jamb, part 1 922.1.66 door and jamb, part 2 922.1.666 door and jamb, part 1 922.1.66 TE 0 3D A8 door and jamb, part 2 922.1.666 door and jamb, part 3 922.1.667 door and jamb, part 1 922.1.668 TE 1 3D FVZ door and jamb, part 2 922.1.669 door and jamb, part 3 922.1.667 TE 60 3D door and jamb, part 1 922.1.671 door and jamb, part 2 922.1.672 door and jamb, part 1 922.1.671 TE 60 3D A8 door and jamb, part 2 922.1.672 door and jamb, part 3 922.1.673 Universal Routing Frame Used to hold the routing templates in place during the milling process 1 frame 92.02.191 2 frames with connecting bar 92.02.331 hinges pages.1-.20 TE 26/27 3D Drilling Jig For drilling the mounting holes Supplied With Drilling jig Drill bit Ø3 mm 92.02.330 www.hafele.com AH.23 1/1
Concealed Mortise Mounted Power Transfer Device The concealed power transfer provides the means to transfer electrical power from the frame to the door leaf Well suited for high abuse areas as conduit is concealed when door is closed UL listed for use on fire doors 9 (3 3/") max. when installed 22 (7/8") from outside face of door Reinforcement 0.0 (1/18") 16 GA min. 6 (1/") 17 (21/") 16 (/8") dia. thru to wire channel 230 (9 1/16") 213 (8 3/8") 16 (/8") for frame 197 (7 3/") 6 (1/") 6 (1/") 2 (1") dia. 16 (/8") for door min. Frame 19 (3/") Door (Open 180 ) Metal Door or Frame Prep (side View) 1 (1 /8") Wood Door or Frame Prep (Side View) Model # PT1 AH.2 Works with doors hung on butt hinges and 3/ (19 mm) offset pivots wires (2 AWG) 180 degrees maximum swing Material: Metal Finish brushed aluminum 912.02.07 Supplied With Wood screws Machine screws Note 1 3/ ( mm) minimum door thickness required. Door and frame require special machining per templates. Not for use with: Swing Clear Hinges, Pocket Pivots, larger than 6 (12 mm), Butt Hinges, 1 1/2 Offset Pivots or Center Hung Pivots. www.hafele.com
Concealed Jamb Door Closer For flush wood and hollow metal doors and frames, not suitable for falling and rising hinges Closing speed and latch action are adjustable Non-handed Cycle test: endurance ested to 00,000 cycles UL B, UL C and UL 228 approved ANSI/BHMA A16. approved Conforms to ADAto meet barrier free applications 98 (3 27/") 22 (7/8") 91 (3 19/") ( 1/2") 179 (7 1/16") 98 (3 27/") 30 (1 3/16") º 98 (3 27/") ( 1/2") 28 (1 3/") 28 (1 3/") 30 ( 12") 18 (7 9/") 3 16 (6 1/2") 16 (/8") 9 (1 1/16") 2. (3/") 200 (7 7/8") Perko Power Maximum door weight: 80 kg (17 lbs.) Maximum door width: 96 mm (38 ) Door thickness: 1 1/2 1 3/ (38 mm) Opening angle: º Material: Anchor and Face Plates: Solid Brass Closer Links: 316 Stainless Steel Finish polished brass 931.90.38 polished chrome 931.90. satin chrome 931.90.3 Supplied With Mounting screws Note Closer should be mounted within 12 (30 mm) from a door hinge. To comply with fire testing closer should be mounted within 30 (762 mm) from the base of the door. For doors with an opening angle larger then º a door stop has be installed. Mounting Bracket For mounting of concealed jamb door closer to hollow metal door frames Material: Raw Steel 931.90.920 www.hafele.com AH.2
Concealed Jamb Door Closer (2 1/8") 26 (1 1/16") 12 ( 19/") 1 (9/16") 38 (1 1/2") 3 3 22 (7/8") Perko Powder-coated mechanism housing Precision-engineered chain Tested up to 00,000 cycles Suitable for fire-rated doors; UL approved, listing mark 8R6 Maximum door opening angle: 130º (for larger openings a door stop should be installed) Suitable for door weights uo to: 0.8 kg (112 lbs.) Minimum door thickness: 38 mm (1 1/2 ) Mounting instructions are supplied with each closer Material: Brass; Anchor Plates: Solid Brass Finish polished 931.90.18 polished chrome 931.90.12 satin chrome 931.90.1 Supplied With Mounting screws Perkomatic Mechanism housed in a light-weight aluminum casing Factory-set smooth controlled rate of closure The sealed hydraulic mechanism can be adjusted to provide the desired latching action Precision-engineered chain ensures smooth and lasting service Designed and tested to 00,000 cycles Suitable for fire-rated doors; UL and cul approved, listing mark 8R6 Suitable for left and right handed applications Suitable for door weights of up to 7 kg (16 lbs.) Minimum door thickness 38 mm (1 1/2 ) Max. door width: 80 mm (33 7/16 ) Maximum door opening angle 130º (for larger openings a door stop should be installed) Material: Brass; Anchor and Face Plates: Solid Brass Finish polished 931.90.08 polished chrome 931.90.22 satin chrome 931.90.2 Distance between centers of fixing plates must not exceed mm 26 (1 1/16") 60 (2 3/8") 26 (1 1/16") 31 Door thickness min. 38 mm (1 1/2") 60 (2 3/8") 168 (6 39/6") (/") 123 ( 7/8") 123 ( 7/8") 31 168 (6 39/6") (2 11/6") (/") (/") Supplied With Mounting screws Mounting instructions Note Closer cannot be used on doors hung on, projecting, rising or falling butt hinges 60 (2 3/8") AH.26 www.hafele.com
Page No. Page No. 912.02.07..................2 922.1.661..................23 922.1.662..................23 922.1.663..................23 922.1.66..................23 922.1.66..................23 922.1.666..................23 922.1.667..................23 922.1.670..................23 922.1.671..................23 922.1.672..................23 922.1.673..................23 92.02.191..................23 92.02.330..................23 92.0.983..................21 92.0.083..................22 92.16.803..................16 92.17.00..................1 92.17.016..................1 92.17.021..................1 92.17.022..................1 92.17.0..................1 92.17.00..................1 92.17.071..................1 92.17.098..................21 92.17.099..................22 92.17...................1 92.17.116..................1 92.17.121..................1 92.17.122..................1 92.17.1..................1 92.17...................1 92.17.171..................1 92.17.198..................21 92.17.199..................22 92.17.20..................17 92.17.216..................17 92.17.221..................17 92.17.222..................17 92.17.2..................17 92.17.20..................17 92.17.271..................17 92.17.298..................21 92.17.299..................22 92.17.30..................18 92.17.1..................18 92.17.2..................18 92.17.3..................18 92.17.30..................18 92.17.1..................18 92.17.0..................19 92.17.21..................19 92.17.22..................19 92.17...................19 92.17.0..................19 92.17.71..................19 92.17.98..................21 92.17.99..................22 92.17.0..................20 92.17.21..................20 92.17.22..................20 92.17...................20 92.17.0..................20 92.17.71..................20 92.17.799..................22 92.17.899..................22 92.19.030..................16 926.0.00...................3 926.0.006................... 926.0.007...................3 926.0.008................... 926.0.0................... 926.0.011................... 926.0.012................... 926.0.013................... 926.0.01................... 926.0.01................... 926.0.016...................6 926.0.020................... 926.0.021................... 926.0.022................... 926.0.023................... 926.0.02................... 926.0.02................... 926.0.026...................6 926.0.030...................7 926.0.031...................7 926.0.0...................7 926.0.033...................7 926.0.03...................7 926.0.03...................7 926.0.00...................9 926.0.01...................9 926.0.02...................9 926.0.03...................9 926.0.0...................9 926.0.0...................9 926.0.00...................8 926.0.01...................8 926.0.02...................8 926.0.03...................8 926.0.0...................8 926.0.0...................8 926.0.068.................. 926.0.069.................. 927.91.2..................11 927.91.26..................11 927.91.28..................11 927.91.3..................11 927.91.36..................11 927.91.38..................11 927.91.90..................12 927.91...................11 927.91.6..................11 927.91.8..................11 927.91.90..................12 927.91.903..................13 927.91.90..................13 927.91.913..................13 927.91.91..................13 931.90.08..................26 931.90.12..................26 931.90.1..................26 931.90.18..................26 931.90.22..................26 931.90.2..................26 931.90...................2 931.90.3..................2 931.90.38..................2 931.90.920..................2 Important This catalog is intended for exclusive use by the recipient. No part of this publication may be distributed in any form to direct competitors of Häfele. Häfele retains complete ownership of this catalog. Häfele reserves the right to demand the return of this catalog in any case where it is employed for purposes of unfair competition. Reproduction of this catalog, either wholly or in part, or reprinting of any drawing or copying of the layout, are strictly forbidden. The technical data and dimensions contained in the drawings are nonbinding and are subject to design improvement. Häfele accepts no liability for any typographical or other type of error which may occur in the production of this catalog. All merchandise is furnished subject to Häfele s official Terms and Conditions of Sale. January, 201 201 Häfele America Co. All rights reserved. Printed in USA. n1