INTERIOR FOLDING DOOR hardware Section Index and General Guide Select system for your interior folding door application. Max. Door Product Data Sheet Track, Channel, Top Guide Channel and Bottom Rail profiles - actual size - and accessories APPLICATION - - D20 System for bifolding doors with equal width leaves. For wardrobes or cupboards. Doors fold open to about 100 degrees allowing unhindered access to over 90 per cent of the opening 14kg Bifold 14 D30 Systems for multi-folding doors - Pivoted, Top Hung, End Folding with equal width leaves. For light folding partitions with equal width leaves up to 620mm each Guide to quantities for Pivotfold 20 systems Guide to quantities for Pivotfold 45 & 75 systems For folding shutters or partitions with equal width leaves up to 900mm each For folding partitions with equal width leaves up to 900mm each For folding partitions with equal width leaves up to 900mm each Systems for multi-folding doors - Hinged to Post, Top Hung and End Folding. For folding partitions with narrow leaf hinged to post. Guide to quantities for Endfold 20 systems Guide to quantities for above Endfold 45 & 75 systems Maximum width 900mm each leaf and height 2400mm Maximum width 900mm each leaf and height 3000mm Maximum width 900mm each leaf and height 3300mm Systems for multi-folding doors - Hinged to Post, Top Hung and Centre Folding. For folding partitions with narrow leaf hinged to post. Guide to Quantities for Centrefold 20 Guide to Quantities for above Centrefold 45 & 75 systems Maximum width 900mm each leaf and height 2400mm Maximum width 920mm each leaf and height 3000mm Maximum width 920mm each leaf and height 3300mm Residential Commercial Industrial 25kg 20kg 45kg 75kg 20kg 45kg 75kg 20kg 45kg 75kg Multifold 25 Pivotfold 20 Pivotfold 45 Pivotfold 75 Endfold 20 Endfold 45 Endfold 75 Centrefold 20 Centrefold 45 Centrefold 75 D40 D50 D60 D70 D80 D80 D90 D100 D110 D120 D120 D130 D140 D150 D160 D160 DaTa ShEET D10
PROFILES For interior folding door hardware PROFILES actual SIzE 60A 901A 902A 904A 904B 904P 904PA 120A 180A 250A 14A A 28.1 9.6 9 20 20 19.5 23 30 45 50 16 B 32 9.4 26 21 21 20.5 24.6 40.7 47 50 20 C 1.5 1.7 2 2 2 2 4 1.6 2 3-250a aluminium 180a aluminium 120a aluminium 14a aluminium 60a aluminium 901a 904P POLy- PROPyLENE 904a aluminium and 904B BRaSS aluminium 904Pa aluminium and POLyPROPyLENE 902a aluminium DaTa ShEET D20
accessories hinge 100 x 75mm No. 360 Flush Bolt. 110 x 24 with 10 mortice and 15 throw. available in satin nickel or titanium gold. No. 456E Lockable Flush Bolt. 190 x 41 with 10 mortice and 20 throw. available in satin nickel or titanium gold. No. 456LX Long Flush Bolt. 600 x 41 with 10 mortice and 20 throw. available in satin nickel or titanium gold. No. 401 Flush Pull. 105 x 41 with 11 mortice. available in satin nickel or titanium gold. No. 456 Flush Bolt. 190 x 41 with 10 mortice and 20 throw. available in satin nickel or titanium gold. No. 456L Long Flush Bolt. 450 x 41 with 10 mortice and 20 throw. available in satin nickel or titanium gold. D20B assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D20B
BIFOLD 14 For top guided interior bi-folding doors. Max 14kg per leaf. application Suitable for residential and light commercial wardrobe and cupboard folding doors Ideal for use on openings with non-rebated jambs as only simple framing at the head is required to take the top track The pivot arrangement allows the leaves to fold open to approximately 100 degrees, allowing unhindered access to over 90% of the opening No bottom guide channel is necessary DOOR SPECIFICaTION Guide System: Bifold 14 For Individual Leaves: Max Leaf height 2400mm (for leaves 29-41mm thick) 2040mm (for leaves 19-41mm thick) Max Leaf weight 14kg Max Leaf width 610mm Min Leaf Thickness 19mm Bifold 14 can be used for any width opening and for any number of leaves, in multiples of two leaf units, by pivoting the third unit of leaves, etc., within the opening. Top and bottom rails should be of sufficient size to ensure solid and secure fitting for the guide and pivots. where solid leaves are used, they should be restricted to 450mm wide. Leaves wider than 450mm should be of light construction and provision made for securing the door knob. Leaves should be made of equal width, allowing 1mm clearance between leaves and 6-7mm clearance at the pivot point and closing stile. STaNDaRD SETS Sets for two leaves comprise track, top pivot socket, bumper, top and bottom pivots, jamb bracket, top guide, three 75x47 FHSS hinges, spanner, all screws and fitting instructions. Sets for four leaves comprise twice the amount of the above hardware, but only one spanner and fitting instruction plus two aligners. Set No. Opening Width B092 Up to 934mm for two leaves B122 1234mm for two leaves B124 1241mm for two leaves pivoted from each side B164 1661mm for two leaves pivoted from each side B184 1861mm for two leaves pivoted from each side B244 2461mm for two leaves pivoted from each side No. 141 Top Pivot Bracket No. 143 Top Pivot hardware SPECIFICaTION Track: 14a Material aluminium mill finish Standard lengths 934mm, 1234mm, 1241mm, 1661m, 1861mm and 2461mm Top Pivot Bracket: 141 Nylon, steel, zinc dichromate Bumper: 146 Rubber Top Pivot: 143 Nylon and steel, zinc dichromate Top Guide: 145 Nylon and steel Bottom Pivot: 144 Steel, zinc dichromate Jamb Bracket: 142 Nylon and steel, zinc dichromate Aligner (4 leaf kit only): 149 Steel, zinc dichromate Hinge: 75x47FhSS Stainless Steel, 75mm non-mortise type Spanner: 14SP Steel, zinc dichromate No. 145 Top Guide No. 75x47FhSS hinge No. 144 Bottom Pivot No. 142 Jamb Bracket No. 14SP Spanner DaTa ShEET D30
10 ( MIN 3 /8") MIN Track TRACK No. 14a NO 310 16 ( 5 /8") Guide GUIDE No. NO 145 315 3 MIN ( 1 /8") MIN Top Pivot Bracket No. 141 FIXING PIN PIN Track No. 14a Bumper No. 146 Top Pivot No.143 Guide No.145 INSIDE DOOR Door height HEIGHT FIN. Final OPENING opening height HEIGHT LESS less 35 35 (1 3 to /8") 40 TO 40 (1 5 /8") NOT TO SCaLE SECTION SCALE 1 : 1 hinges 75x47FhSS view FROM INSIDE ANGLE angle PLaTE PLATE Door aligners 149 (4. door sets only) BOTTOM Bottom Pivot PIVOT No. NO.314 144 16 16 ( 5 /8") MIN MIN (ADD EXTRA (add extra CLEARANCE clearance for FOR carpet) CARPET) Bottom Pivot No.144 Bottom Jamb Bracket No.142 Leaf width for 2 Leaf Set: Divide finished opening width by 2 and subtract 7mm from each door. Leaf width for 8 Leaf Unit: Divide finished opening width by 8 and subtract 4mm from each door. Leaf width for 4 Leaf Set: Divide finished opening width by 4 and subtract 5mm from each door. Leaf width for 6 Leaf Unit: Divide finished opening width by 6 and subtract 4mm from each door. assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D30B
MULTIFOLD 25 For top hung interior folding partitions. Max 25kg each leaf. application Suitable for residential and light commercial folding partitions Leaves can be either end folding or centre folding Leaves can fold to one or both sides of the opening Pivot hardware enables an end folding internal partition to be designed using standard width door leaves with no need to reduce the width of the leaf adjacent to the jamb DOOR SPECIFICaTION Track System: Multifold 25 For Individual Leaves: Max Leaf height 2400mm Max Leaf weight 25kg Max Leaf width 620mm Min Leaf Thickness 20mm The folding unit is not hinged to a jamb, but is pivoted in the track and on the adjustable jamb bracket. End folding units of two, four, six or eight leaves can be pivoted to each side of the opening. Centre folding units of one, three, five or seven full width leaves and one half width leaf can be pivoted to each side of the opening. a guide system across the floor must be used on end folding units of four leaves or more in excess of 450mm wide or 15kg per leaf. Instructions on leaf width calculation is shown overleaf. Door leaves should be constructed to provide secure fitting for the pivots, s, hinges and guides and can be either flush, panelled or of louvre construction. STaNDaRD SETS and PaCKS Set No. Contents MF2 2 door pack MF4 4 door pack MF6 6 door pack hardware SPECIFICaTION Track punched for soffit fitting: 60a Material aluminium Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Top Pivot Assembly: MF25TP Steel, zinc dichromated, Nylon Bottom Pivot: MF25BP Steel, zinc dichromated, Nylon Hanger: 60SN The is fitted with four nylon tyred ballrace wheels. The adjustment bolt is attached to the top plate and secured in place with a locking clip which allows easy installation. all steel parts are zinc dichromated. Hinges: 75X47FhSS Stainless steel non mortise hinge Screws for the hinges are stainless steel. The other screws are in zinc dichromate finish. Spanner: 60SP Steel, in zinc dichromate finish Accessories: Bracket: 1/60 Bracket made from steel and supplied with matching fasteners. available in a pack of 5 or 8, reference 1/60/5 and 1/60/8 respectively. Channels: 901a aluminium channel, available in 1200, 1500, 1800, 2400 and 3600mm Guide: 8G/901 Spring loaded guide for use with 901a or 902a channels. Guide is nylon and stainless steel. Threshold: 902a 902a threshold, aluminium, available in 2100, 3000, 4000 and 6000mm Flush Pull with deep grip: 401 Flush Bolt with flat shoot: 360 MF25TP Top Pivot No. 75x47FhSS hinge No. 8G/901 No. 901a Channel MF25BP Bottom Pivot No. 1/60 Bracket No. 60SN No. 902a Channel DaTa ShEET D40
assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D40B
GUIDE TO QUaNTITIES For top hung interior folding partitions on Pivotfold 20 track system This Guide to Quantities is only applicable to Data Sheets D70. SPECIFICaTIONS and QUaNTITIES The specifications below and overleaf detail the maximum and minimum capacities for the track systems recommended. Determine the number of leaves required to cover the opening. The leaves are hinged together to form one or two units of up to six leaves each, with each unit pivoted to one side of the opening. wider openings can be covered by including a four or six leaf unit floating to either side of the opening. If the leaf weight is unknown, the weight can be calculated using the chart in Section a. having calculated the weight, use the information below to select the appropriate track system and quantities for the unit or units required to cover the opening width. Specification for Individual Leaves Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 19mm Track System Pivotfold 20 Refer to Data Sheet D70 2 Leaf unit pivoted to one side Quantities Reference Numbers Track See overleaf 120a 120a Bracket (face fix) See overleaf 1/250 1/250 Pivot Set 1 20PNC 20P 1 120SN 120SN hinges 3 90X50FhSS 90X50FhSS Guide 1 No guide Req. 106E/94 Channel See overleaf No channel Req. 904a, 904B, 904P & 904Pa Flush Pulls 2 401 401 Flush Bolt 1 456 456 3 Leaf unit pivoted to one side Track See overleaf 120a Bracket (face fix) See overleaf 1/250 Pivot Set 1 20P 1 120SN hinges 6 90X50FhSS Guide 1 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 2 401 Flush Bolt 1 456 4 Leaf unit pivoted to one side Track See overleaf 120a Bracket (face fix) See overleaf 1/250 Pivot Set 1 20P 2 120SN hinges 9 90X50FhSS Guide 2 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 2 456 4 Leaf floating unit Track See overleaf 120a Bracket (face fix) See overleaf 1/250 3 120SN hinges 9 90X50FhSS Guide 3 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 2 456 5 Leaf unit pivoted to one side Track See overleaf 120a Bracket (face fix) See overleaf 1/250 Pivot Set 1 20P 2 120SN hinges 12 90X50FhSS Guide 2 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 2 456 DaTa ShEET D50
GUIDE TO QUaNTITIES For top hung interior folding partitions on Pivotfold 20 Track System Specification for Individual Leaves Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 19mm Track System Pivotfold 20 Refer to Data Sheet D70 6 Leaf unit pivoted to one side Quantities Reference Numbers Track See below 120 Bracket (face fix) See below 1/250 Pivot Set 1 20P 3 120SN hinges 15 90X50FhSS Guide 3 5G/904 Channel See below 904a, 904B, 904P & 904Pa Flush Pulls 4 401 Flush Bolt 3 456 6 Leaf floating unit Track See below 120 Bracket (face fix) See below 1/250 s 4 120SN hinges 15 90X50FhSS Guide 4 5G/904 Channel See below 904a, 904B, 904P & 904Pa Flush Pulls 4 401 Flush Bolt 3 456 2 Additional Leaves Maximum height for 6 Leaf unit is 2400mm 1 120SN hinges 6 90X50FhSS Guide 1 5G/904 Flush Pull 1 401 Flush Bolt 1 456 TRaCK, BRaCKET and ChaNNEL QUaNTITIES Select the correct reference numbers for track, bracket, end clips and channel from the appropriate columns above and overleaf to suit the leaf weight etc. From the table below, choose the quantities of these items. TRaCK and ChaNNEL Choose sufficient track and channel to cover the overall opening width. If a floating unit is required to slide clear of the opening, then sufficient track and channel is required to cover the widths of the reveal and the opening. BRaCKET SPaCING (FaCE FIX) Place a bracket at each end of the track, at each join in the track, at 300mm from the post to which a unit folds and with the remaining brackets spaced symmetrically between the other brackets at not more than 900mm centres. Overall width of Leaves (plus reveal if unit floating Track lengths Bracket lengths Channel clear of opening) 2000 1 x 2000 4 1 x 2000 3000 1 x 3000 5 1 x 3000 4000 1 x 4000 7 1 x 4000 5000 1 x 5000 8 1 x 5000 6000 1 x 6000 9 1 x 6000 7000 1 x 3000 11 1 x 3000 1 x 4000 1 x 4000 8000 2 x 4000 13 2 x 4000 D50B assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D50B
GUIDE TO QUaNTITIES For top hung interior folding partitions on Pivotfold 45 & 75 Track Systems This guide to quantities is only applicable to data sheets D80. SPECIFICaTIONS and QUaNTITIES The specifications below and overleaf detail the maximum and minimum capacities for the track systems recommended. Determine the number of leaves required to cover the opening. The leaves are hinged together to form one or two units of up to eight leaves each, with each unit pivoted to one side of the opening. wider openings can be covered by including a four, six or eight leaf unit floating to either side of the opening. If the leaf weight is unknown, the weight can be calculated using the chart in Section a. having calculated the weight, use the information below to select the appropriate track system and quantities for the unit or units required to cover the opening width. Specification for Individual Leaves Max Leaf height 2400mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 900mm 900mm Min Leaf Thickness 35mm 44mm Track System Pivotfold 45 Pivotfold 75 Refer to Data Sheet D80 D80 2 Leaf unit pivoted to one side Quantities Reference Numbers Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 Pivot Set 1 45/75P 45/75P 1 45PF 75PF hinges 3* 100x75LPSS 100x75LPSS Guide 1 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 2 401 401 Flush Bolt 1 456 456 *For Leaves exceeding 2400mm high, increase to 4 3 Leaf unit pivoted to one side Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 Pivot Set 1 45/75P 45/75P s 1 45PF/4 75PF/4 hinges 6* 100x75LPSS 100x75LPSS Guide 1 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 2 401 401 Flush Bolt 1 456 456 *For Leaves exceeding 2400mm high, increase to 8 4 Leaf unit pivoted to one side Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 Pivot Set 1 45/75P 45/75P s 1 45PF 75PF s 1 45PF/4 75PF/4 hinges 9* 100x75LPSS 100x75LPSS Guide 2 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 3 401 401 Flush Bolt 2 456 456 *For Leaves exceeding 2400mm high, increase to 12 4 Leaf floating unit Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 s 2 45PF 75PF s 1 45PF/4 75PF/4 hinges 9* 100x75LPSS 100x75LPSS Guide 3 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 3 401 401 Flush Bolt 2 456 456 *For Leaves exceeding 2400mm high, increase to 12 5 Leaf unit pivoted to one side Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 Pivot Set 1 45/75P 45/75P 2 45PF/4 75PF/4 hinges 12* 100x75LPSS 100x75LPSS Guide 2 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 2 401 401 Flush Bolt 2 456 456 *For Leaves exceeding 2400mm high, increase to 16 DaTa ShEET D60
GUIDE TO QUaNTITIES For top hung interior folding partitions on Pivotfold 45 & 75 Track Systems Specification for Individual Leaves Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 900mm 900mm Min Leaf Thickness 35mm 44mm Track System Pivotfold 45 Pivotfold 75 Refer to Data Sheet D80 D80 6 Leaf unit pivoted to one side Quantities Reference Numbers Track See below 180 250 Bracket (face fix) See below 1/250 1/250 Pivot Set 1 45/75P 45/75P s 2 45PF/4 75PF/4 s 1 45PF 75PF hinges 15* 100x75LPSS 100x75LPSS Guide 3 4G/904 4G/904 Channel See below 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 4 401 401 Flush Bolt 3 456 456 *For Leaves exceeding 2400mm high, increase to 20 6 Leaf floating unit Track See below 180 250 Bracket (face fix) See below 1/250 1/250 s 2 45PF/4 45PF/4 s 2 45PF 75PF hinges 15* 100x75LPSS 100x75LPSS Guide 4 4G/904 4G/904 Channel See below 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 4 401 401 Flush Bolt 3 456 456 *For Leaves exceeding 2400mm high, increase to 20 The quantities for 7or 8 leaves pivoted to one side or for eight leaves floating to either side can be calculated by adding the quantities below for two leaves to the previously shown quantities of five leaves pivoted to one side, six leaves pivoted to one side or six floating leaves respectively. 2 Additional Leaves to increase 5 or 6 Leaf units to 7 or 8 Leaf units Maximum height for 7 Leaf unit is 3000mm 1 45PF/4 75PF/4 hinges 6* 100x75LPSS 100x75LPSS Guide 1 4G/904 4G/904 Flush Pull 1 401 401 Flush Bolt 1 456 456 *For Leaves exceeding 3000mm high, increase to 8 TRaCK, BRaCKET and ChaNNEL QUaNTITIES Select the correct reference numbers for track, bracket, end clips and channel from the appropriate columns above and overleaf to suit the leaf weight etc. From the table below, choose the quantities of these items TRaCK and ChaNNEL Choose sufficient track and channel to cover the overall opening width. If a floating unit is required to slide clear of the opening, then sufficient track and channel is required to cover the widths of the reveal and the opening. BRaCKET SPaCING (FaCE FIX) Place a bracket at each end of the track, at each join in the track, at 300mm from the post to which a unit folds and with the remaining brackets spaced symmetrically between the other brackets at not more than 900mm centres. Overall width of Leaves (plus reveal if unit floating Track lengths Bracket lengths Channel clear of opening) 2000 1 x 2000 4 1 x 2000 3000 1 x 3000 5 1 x 3000 4000 1 x 4000 7 1 x 4000 5000 1 x 5000 8 1 x 5000 6000 1 x 6000 9 1 x 6000 7000 1 x 3000 11 1 x 3000 1 x 4000 1 x 4000 8000 2 x 4000 13 2 x 4000 assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D60B
PIvOTFOLD 20 For top hung interior pivot folding partitions. Max 20kg each leaf. application Suitable for residential and light commercial pivot folding partitions, with all leaves of equal width. Leaves can fold to one or both sides of the opening Pivot hardware enables an end folding interior shutters to be designed using standard width leaves with no cutting down of the leaf adjacent to post To cover any width opening, any number of folding units can be used DOOR SPECIFICaTION Track System: Pivotfold 20 For Individual Leaves: Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 35-50mm Pivotfold 20 units of up to six leaves can be pivoted to each side of the opening. End folding floating units consist of four or six leaves. Shutter leaves should be constructed to provide secure fitting for the pivot sets, s, hinges and guides hardware SPECIFICaTION Track: Material Standard lengths 120a aluminium, Mill or Clear anodised 2000mm, 3000mm, 4000mm and 6000mm. Bracket (Face Fix): Bracket 316 Stainless Steel 1/250 a bracket is located close to the pivot with a bracket 300mm away to support track where folding units stack. Place a bracket at the other end of the track, at each join in the track and space the other brackets at 900mm maximum centres. Hangers: End & Intermediate 120SN alternative 80SN Hangers are fitted with nylon tyre wheels on ball race bearings. Vertical adjustment is simple and positive. Pivot Set: Top and bottom pivots 20P 2 Door Pivot No Channel 20PNC Guide: with precision bearings 5G/904 all steel parts to s, pivots and guides are stainless steel. Hinge: Butt hinge 90X50FhSS Channels: aluminium 904a Brass 904B Polypropylene & alum. 904Pa Finish: aluminium - Mill or Clear anodised Standard lengths 2000mm, 3000mm, 4000mm & 6000mm Accessories: Flush Pulls, Flush Bolts Finish: PvD Brass, Satin Nickel No. 120SN No. 20P Pivot No. 80SN No. 20DS Door Stop No. 90X50FhSS No. 401 Flush Pull 105 x 41 with 11 mortise No. 20PNC Pivot No. 5G/904 Guide DaTa ShEET D70
16 Thick Timber Pad Track cut to fit tight on jamb No. 20PNC Top Pivot No. 120SN No. 120 Track No. 20DS Door Stop No. 20PNC Top Pivot Fit hinges 3.5 offset to centre of pin. No. 120SN No. 90X50FhSS Butt hinge Jamb No. 360 Flush Bolt No. 90X50FhSS hinge Jamb Floor Equal Equal Section NOT TO Scale SCaLE 1:2 No. 90X50FhSS hinge No. 20DS Door Stop No. 20PNC Bottom Pivot for 2 or 2+2 leaf applications Floor No. 20PNC Pivot No. 401 Flush Pull & No. 360 Flush Bolt on this leaf No. 120SN PIvOTFOLd 20-4 OR MORE LEAvES, WITH BOTTOM CHANNEL No. 20P Adjustable Bottom Pivot Track cut to fit tight on jamb No. 20P Top Pivot No. 120SN No. 20DS Door Stop Floor No. 904Pa Polypropylene and aluminium support channel recessed into floor No. 20P Adjustable Bottom Pivot Floor No. 20P Pivot No. 90X50FhSS hinge No. 120SN PIvOT No. 20DS Door Stop GUIdE No. 5G/904 End Guide No. 20P Pivot No. 401 Flush Pull on this leaf No. 120SN No. 90X50FhSS hinge No. 401 Flush Pull on this leaf No. 120SN No. 120SN No. 120SN No. 401 Flush Pull on this leaf No. 401 Flush Pull on this leaf No. 401 Flush Pull on this leaf assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D70B
PIvOTFOLD 45 & 75 For top hung interior pivot folding partitions. Max 75kg each leaf. application Suitable for residential and commercial pivot folding partitions, with all leaves of equal width Leaves can fold to one or both sides of the opening Pivot hardware enables an end folding internal partition to be designed using standard width door leaves with no cutting down of the leaf adjacent to post To cover any width opening, any number of folding units can be used DOOR SPECIFICaTION Track System: Pivotfold 45 Pivotfold 75 For Individual Leaves: Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 900mm 900mm Min Leaf Thickness 35mm 44mm Use Pivotfold only if leaves must be of equal width. Endfold is preferred because the first leaf is hinged to a post. See Data Sheet D120. The folding unit is not hinged to a post, but is pivoted in the track and off the floor. End folding units of up to eight leaves can be pivoted to each side of the opening. a pivoted unit with an odd number of leaves provides a hinged access door. End folding floating units consist of four, six or eight leaves. Clearance between leaves to be 2mm minimum. Door leaves should be constructed to provide secure fitting for the pivot sets, s, hinges and guides and can be flush, panelled or glazed. hardware SPECIFICaTION Track: 180a 250a Material aluminium aluminium Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Bracket (Face Fix): Bracket 316 Stainless Steel 1/250 1/250 a bracket is located close to the pivot with a bracket 300mm away to support track where folding units stack. Place a bracket at the other end of the track, at each join in the track and space the other brackets at 900mm maximum centres. Hangers: End leaves 45PF 75PF Intermediate Leaves 45PF/4 75PF/4 s are fitted with nylon tyre wheels on ball race bearings. Vertical adjustment is simple and positive. Pivot Set: Top and bottom pivots 45/75P 45/75P Guide: with precision bearings 4G/904 4G/904 all steel parts to s, pivots and guides are stainless steel. Hinge: Butt hinge 100X75LPSS 100X75LPSS Channels: aluminium 904a 904a Brass 904B 904B Polpropylene & alum Support 904Pa 904Pa Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Accessories: Flush Pulls, Flush Bolts Finish: PvD Brass and Satin Nickel 45P & 75P 45PF/4 & 75PF/4 4G/904 Guide 1/250 Bracket No. 401 Flush Pull 105 x 41 with 11 mortise No. 456 Flush Bolt 190 x 41 with 10 mortise and 20 throw 100x75LPSS Butt hinge No. 45/75P Pivot Set Top assembly No. 45/75P Pivot Set Bottom assembly DaTa ShEET D80
16 Thick Timber Pad Track cut to fit tight on jamb No. 45/75P Top Pivot No. 45/75P Top Pivot No. 180 Track No. PS13B or PS16B Brush Seal Bore hole for 27 dia. x 36 to allow bolt to withdraw angle Plate vertical leg narrower to allow for rebating s, 2 wheels or 4 wheels for stability. Fitted on leaf adjacent to access door when access door forms part of the unit. 1/250 Bracket M6 screw with washer and captive nut 250 Track Bolt and Pull PLAN 2 Pull Bolt and Pull PLAN 1 view SHOWING ALTERNATIvE NO. 250 TRACK ANd 1/250 BRACKET No. 45/75P Top Pivot No. 1/250 Bracket Extra bracket to take weight of folded door 100X75LPSS Butt hinge Fit hinges 6 offset to centre of Pin. Radius to clear jamb when pivoting Fit hinges clear of and guide plate No. 400 Flush Pulls Flush Bolt angle Plate vertical leg narrower to allow for rebating 6 min. clearance Section NOT TO Scale SCaLE 1:2 No. 4G/904 Guide Cover fillet PIvOT detail TOP OF door WITH HANGER REMOvEd No. 45/75P Pivot Set No. 45/75P Bottom Pivot No. 4G/904 Guide TYPICAL ELEvATION AS PLAN 2 904Pa Polypropylene channel with aluminium support channel recessed into floor Lug for concrete Pivot socket alternate Pivot cup attachment assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D80B
GUIDE TO QUaNTITIES For top hung interior folding partitions on Endfold 20 track system This Guide to Quantities is only applicable to data sheets D110. SPECIFICaTIONS and QUaNTITIES The specifications below and overleaf detail the maximum and minimum capacities for the track systems recommended. Determine the number of leaves required to cover the opening. The leaves are hinged together to form units of up to six leaves hinged to a post. wider openings can be covered by including units floating to either side of the opening. Floating units consist of four or six leaves. If the leaf weight is unknown, the weight can be calculated using the chart in Section a. having calculated the weight, use the information below to select the appropriate track system and quantities for the unit or units required to cover the opening width. Specification for Individual Leaves Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 19mm Track System Endfold 20 Refer to Data Sheet D110 2 Leaf unit hinged to post Quantities Reference Numbers Track 120 Bracket (face fix) See overleaf I/250 1 120SN hinges 6 90X50FhSS Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 2 401 Flush Bolt 1 456 3 Leaf unit hinged to post including access door Track See overleaf 120 Bracket (face fix) See overleaf I/250 s 1 120SN hinges 9 90X50FhSS Guide 1 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 2 401 Flush Bolt 1 456 4 Leaf unit hinged to a post Track See overleaf 120 Bracket (face fix) See overleaf I/250 2 120SN hinges 12 90X50FhSS Guide 2 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 2 456 4 Leaf floating unit Track See overleaf 120 Bracket (face fix) See overleaf I/250 3 120SN hinges 9 90X50FhSS Guide 3 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 2 456 5 Leaf unit pivoted to one side Track See overleaf 120 Bracket (face fix) See overleaf I/250 2 120SN hinges 15 90X50FhSS Guide 2 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 2 456 DaTa ShEET D90
GUIDE TO QUaNTITIES For top hung interior folding partitions on Endfold 20 track system Specification for Individual Leaves Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 19mm Track System Endfold 20 Refer to Data Sheet D110 6 Leaf unit pivoted to one side Quantities Reference Numbers Track See below 120 Bracket (face fix) See below I/250 s 3 120SN hinges 18 90X50FhSS Guides 3 5G/904 Channel See below 904a, 904B, 904P & 904Pa Flush Pulls 4 401 Flush Bolt 3 456 6 Leaf floating unit Track See below 120 Bracket (face fix) See below I/250 s 4 120SN hinges 15 90X50FhSS Guides 4 5G/904 Channel See below 904a, 904B, 904P & 904Pa Flush Pulls 4 401 Flush Bolt 3 456 2 Additional Leaves Maximum height for 6 Leaf unit is 2400mm 1 120SN hinges 6 90X50FhSS Guide 1 5G/904 Flush Pull 1 401 Flush Bolt 1 456 TRaCK and ChaNNEL Choose sufficient track and channel to cover the overall opening width. If a floating unit is required to slide clear of the opening, then sufficient track and channel is required to cover the widths of the reveal and the opening. BRaCKET SPaCING (FaCE FIX) Place a bracket at each end of the track, at each join in the track, at 300mm from the post to which a unit folds and with the remaining brackets spaced symmetrically between the other brackets at not more than 900mm centres. Overall width of Leaves (plus reveal if unit floating Track lengths Bracket lengths Channel clear of opening) 2000 1 x 2000 4 1 x 2000 3000 1 x 3000 5 1 x 3000 4000 1 x 4000 7 1 x 4000 5000 1 x 5000 8 1 x 5000 6000 1 x 6000 9 1 x 6000 7000 1 x 3000 11 1 x 3000 1 x 4000 1 x 4000 8000 2 x 4000 13 2 x 4000 D90B assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D90B
GUIDE TO QUaNTITIES For top hung interior folding partitions on Endfold 45 & 75 systems This Guide to Quantities is only applicable to Data Sheets D120. SPECIFICaTIONS and QUaNTITIES The specifications below and overleaf detail the maximum and minimum capacities for the track systems recommended. Determine the number of leaves required to cover the opening. The leaves are hinged together to form units of up to eight leaves hinged to a post. wider openings can be covered by including units floating to either side of the opening. Floating units consist of four, six or eight leaves. If the leaf weight is unknown, the weight can be calculated using the chart in Section a. having calculated the weight, use the information below to select the appropriate track system and quantities for the unit or units required to cover the opening width. Specification for Individual Leaves Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 900mm 900mm Min Leaf Thickness 35mm 44mm Track System Endfold 45 Endfold 75 Refer to Data Sheet D120 D120 2 Leaf unit hinged to post Quantities Reference Numbers Track 180 250 Bracket (face fix) See overleaf I/250 I/250 1 45PF 75PF hinges 6* 100X75LPSS 100X75LPSS Guide 1 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 2 401 401 Flush Bolt 1 456 456 *For Leaves exceeding 2400mm high, increase to 8 3 Leaf unit hinged to post including access door Track See overleaf 180 250 Bracket (face fix) See overleaf I/250 I/250 1 45PF/4 75PF/4 hinges 9 100X75LPSS 100X75LPSS Guide 1 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 1 401 401 Flush Bolt 1 456 456 *For Leaves exceeding 2400mm high, increase to 12 4 Leaf unit hinged to a post Track See overleaf 180 250 Bracket (face fix) See overleaf I/250 I/250 1 45PF 75PF 1 45PF/4 75PF/4 hinges 12* 100X75LPSS 100X75LPSS Guides 2 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 3 401 401 Flush Bolt 2 456 456 *For Leaves exceeding 2400mm high, increase to 16 4 Leaf floating unit Track See overleaf 180 250 Bracket (face fix) See overleaf I/250 I/250 2 45PF 75PF 1 45PF/4 75PF/4 hinges 9* 100X75LPSS 100X75LPSS Guide 3 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 3 401 401 Flush Bolt 2 456 456 *For Leaves exceeding 2400mm high, increase to 12 5 Leaf unit hinged to post including access door Track See overleaf 180 250 Bracket (face fix) See overleaf I/250 I/250 2 45PF/4 75PF/4 hinges 15 100X75LPSS 100X75LPSS Guides 2 4G/904 4G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 2 401 401 Flush Bolt 2 456 456 *For Leaves exceeding 2400mm high, increase to 20 DaTa ShEET D100
GUIDE TO QUaNTITIES For top hung interior folding partitions on Endfold 45 & 75 systems Specification for Individual Leaves Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 900mm 900mm Min Leaf Thickness 35mm 44mm Track System Endfold 45 Endfold 75 Refer to Data Sheet D120 D120 6 Leaf unit pivoted to one side Quantities Reference Numbers Track See below 180 250 Bracket (face fix) See below I/250 I/250 s 1 45PF 75PF s 2 45PF/4 75PF/4 hinges 18* 100X75LPSS 100X75LPSS Guides 3 4G/904 4G/904 Channel See below 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 4 401 401 Flush Bolt 3 456 456 *For Leaves exceeding 2400mm high, increase to 24 6 Leaf floating unit Track See below 180 250 Bracket (face fix) See below I/250 I/250 s 2 45PF 75PF s 2 45PF/4 75PF/4 hinges 15* 100X75LPSS 100X75LPSS Guides 4 4G/904 4G/904 Channel See below 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 4 401 401 Flush Bolt 3 456 456 *For Leaves exceeding 2400mm high, increase to 20 The quantities for seven or eight leaves pivoted to one side or for eight leaves floating to either side can be calculated by adding the quantities below for two leaves to the previously shown quantities of five leaves pivoted to one side, six leaves pivoted to one side or six floating leaves respectively. 2 Additional Leaves to increase 5 or 6 Leaf units to 7 or 8 Leaf units Maximum height for 7 Leaf unit is 3000mm 1 45PF/4 75PF/4 hinges 6* 100X75LPSS 100X75LPSS Guide 1 4G/904 4G/904 Flush Pull 1 401 401 Flush Bolt 1 456 456 *For Leaves exceeding 2400mm high, increase to 8 TRaCK and ChaNNEL Choose sufficient track and channel to cover the overall opening width. If a floating unit is required to slide clear of the opening, then sufficient track and channel is required to cover the widths of the reveal and the opening. BRaCKET SPaCING (FaCE FIX) Place a bracket at each end of the track, at each join in the track, at 300mm from the post to which a unit folds and with the remaining brackets spaced symmetrically between the other brackets at not more than 900mm centres. Overall width of Leaves (plus reveal if unit floating Track lengths Brackets Channel clear of opening) 2000 1 x 1000 4 1 x 2000 3000 1 x 3000 5 1 x 3000 4000 1 x 4000 7 1 x 4000 5000 1 x 5000 8 1 x 5000 5000 1 x 6000 9 1 x 6000 7000 1 x 3000 11 1 x 3000 1 x 4000 1 x 4000 8000 2 x 4000 13 2 x 4000 assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D100B
ENDFOLD 20 For top hung interior end folding partitions. Max 20kg each leaf. application Suitable for residential or commercial end folding partitions Leaves can fold to one or both sides of the opening and can be stacked behind a reveal if required To cover any width of opening, any number of folding units can be used DOOR SPECIFICaTION Track System: Endfold 20 For Individual Leaves: Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 35-50mm Folding units of up to eight leaves can be hinged to a post. a unit with an odd number of leaves, hinged to a post, provides a hinged access door. alternatively, access should be through either a separate door hinged to a post or a door hinged in one of the folding leaves. Floating units consist of four or six leaves. Instruction on leaf width calculation is shown overleaf. Clearance between leaves to be 2mm minimum. Door leaves should be constructed to provide secure fitting for the s, hinges and guides and can be flush, panelled or glazed. hardware SPECIFICaTION Track: 120 Material aluminium, Mill or Clear anodised Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Bracket (Face Fix): Bracket 316 Stainless Steel 1/250 a bracket is located close to the pivot with a bracket 300mm away to support track where folding units stack. Place a bracket at the other end of the track, at each join in the track and space the other brackets at 900mm maximum centres. Hangers: End & Intermediate 120SN alternative 80SN s are fitted with nylon wheels on ball race bearings. Vertical adjustment is simple and positive. Guide: with precision bearing 5G/904 all steel parts to s and guides are stainless steel. Hinge: Butt hinge 90X50FhSS Channels: aluminium 904a Brass 904B Polypropylene & aluminium 904Pa Finish: aluminium Mill or Clear anodised Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Accessories: Flush Pulls, Flush Bolts Finish: PvD Brass, Satin Nickel. No. 120SN No. 80SN No. 5G/904 Guide No. 20DS Door Stop No. 401 Flush Pull 105 x 41 with 11 mortise 90X50FhSS hinge DaTa ShEET D110
16 Thick Timber Pad Door preparation for 120SN No. 120SN No. 20DS Door Stop No. 120 Track No. 120SN See detail at left for attachment details Floor Fit hinges 3.5 offset to centre of Pin No. 904Pa Polypropylene & aluminium Support Channel recessed into Floor No. 5G/904 Guide 90x50FhSS Butt hinge 90x50FhSS hinge To provide an opening for maintenance, mount Track 40mm off face of Jamb Post No. 120 Track 90x50FhSS hinge No. 401 Flush Pull access Door 90x50FhSS hinge Channel No. 401 Flush Pull Jamb 90x50FhSS hinge NOT TO SCaLE No. 401 Flush Pull No. 401 Flush Pull HINGEd TO JAMB LEAF WIdTH CALCULATIONS No. 5G/904 Guide Floor No. 904Pa Polypropylene & aluminium Support Channel recessed into Floor assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D110B
ENDFOLD 45 & 75 For top hung interior end folding partitions. Max 75kg each leaf. application Suitable for residential or commercial end folding partitions Leaves can fold to one or both sides of the opening and can be stacked behind a reveal if required To cover any width of opening, any number of folding units can be used DOOR SPECIFICaTION Track System: Endfold 45 Endfold 75 For Individual Leaves: Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 900mm 900mm Min Leaf Thickness 35mm 44mm Folding units of up to eight leaves can be hinged to a post. a unit with an odd number of leaves, hinged to a post, provides a hinged access door. alternatively, access should be through either a separate door hinged to a post or a door hinged in one of the folding leaves. Floating units consist of four, six or eight leaves. Instruction on leaf width calculation is shown overleaf. Clearance between leaves to be 2mm minimum. Door leaves should be constructed to provide secure fitting for the s, hinges and guides and can be flush, panelled or glazed. hardware SPECIFICaTION Track: 180 250 Material aluminium aluminium Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Brackets (Face Fix): Face fitted bracket, 316 stainless I/250 I/250 Fit at 900mm maximum centres. Fit additional bracket where folding units stack and at the ends of the track. Hangers: End leaves 45PF 75PF Intermediate leaves 45PF/4 75PF/4 s are fitted with nylon wheels on a ball race bearing. Vertical adjustment is simple and positive. Guide: with precision bearing 4G/904 4G/904 all steel parts to s and guides are stainless steel. Hinge: Butt hinge 100X75LPSS 100X75LPSS 100x75 Channels: aluminium 904a 904a Brass 904B 904B Polypropylene & alum. Support 904Pa 904Pa Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Accessories: Flush Pulls, Flush Bolts Finish: PvD Brass & Satin Nickel 45PF/4 & 75PF/4 No. 401 Flush Pull 105 x 41 with 11 mortice 1/250 Bracket No. 456 Flush Bolt 190 x 41 with 10 mortice and 20 throw 45PF & 75PF 100 x 75 hinge No. 4G/904 Guide DaTa ShEET D120
Fixing for all brackets, M8 bolts or coach screws 16 Thick Timber Pad No. 180 Track M6 Bolt with washer and captive nut No. 1/250 Bracket No. 250 Track No. PS13B or PS16B Brush Seal Bore for 27 dia. x 36 to allow bolt to withdraw angle Plate vertical leg narrower to allow for rebating Fit hinges 6 offset to centre of pin except those on leaf hinged to post - see below 100x75 Butt hinge s 2 wheels or 4 wheels fitted on leaf adjacent to access door when access door forms part of the unit. FORMULA FOR LEAF WIdTH CALCULATIONS all leaves are the same width, hinge pin to hinge pin centres. Except a leaf hinged to a post, which must be narrower by the sum of half the leaf thickness plus 38mm. If the stiles are being rebated, the leaves will have to be made wider than calculated to allow for the rebating. The formula for calculating the width of leaves for a partition 44 thick is as follows - add 60 (half leaf thickness + 38) to the width between the rebated posts for each leaf hinged to a post and divide the result by the number of leaves. This gives the width of the wider leaves. The leaf hinged to the post is 60 less. Deduct 2 from each measurement for clearances. For example, 2 units of 4 leaves 44 thick, each hinged to opposite posts, with 6984 overall between posts - 6984 + 60 + 60) / 8 = 888 less 2 = 886 for width of wider leaves. 888 less 60 less 2 = 826 for width of leaves hinged to posts. view SHOWING ALTERNATIvE NO. 250 TRACK ANd 1/250 BRACKET No. 45PF & 75PF 1/250 Stainless Steel Bracket HANGERS To provide an opening for maintenance, mount track 40mm off face of jamb post. Extra bracket to take weight of folded door No. 45PF & 75PF/4 TYPICAL ELEvATION AS PLAN 2 NOT TO SCaLE angle plate vertical leg narrower to allow for rebating 6 min. clearance No. 4G/904 Guide Orient guide roller outwards on all end leaves as shown No. 904P Polypropylene channel PLaN 1 PLaN 2 4 Leaves floating to left as plan 1 Note: No offset to hinges on post fit pin centre flush with face of leaf 4 Leaves hinged to post with separate access door as plan 2 access door hinged to post 904Pa polypropylene channel and aluminium support channel in reversible sill aluminium support channel Rebated joints if rebating is preferred it must be to layout above Tongue and groove joints. These joints, with hardwood tongues are recommended D120B assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D120B
GUIDE TO QUaNTITIES For top hung interior folding partitions on Centrefold 20 track system This Guide to Quantities is only applicable to data sheets D150. SPECIFICaTIONS and QUaNTITIES The specifications below and overleaf detail the maximum and minimum capacities for the track systems recommended. Determine the number of leaves required to cover the opening. The leaves are hinged together to form units of up to five full leaves and one half leaf hinged to a post. wider openings can be covered by including units floating to either side of the opening. Floating units consist of up to five full leaves. If the leaf weight is unknown, the weight can be calculated using the chart in Section a. having calculated the weight, use the information below to select the appropriate track system and quantities for the unit or units required to cover the opening width. Specification for Individual Leaves Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 19mm Track System Centrefold 20 Refer to Data Sheet D150 1 1 / 2 Leaf unit hinged to post Quantities Reference Numbers Track See overleaf 120 Bracket (face fix) See overleaf I/250 1 120SN hinges 6 90X50FhSS Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 2 401 Flush Bolt 2 456 2 1 / 2 Leaf unit hinged to post including access door Track See overleaf 120 Bracket (face fix) See overleaf I/250 1 120SN hinges 9 90X50FhSS Guide 1 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 3 456 3 1 / 2 Leaf unit hinged to a post Track See overleaf 120 Bracket (face fix) See overleaf I/250 2 120SN hinges 12 90X50FhSS Guides 2 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 3 401 Flush Bolt 3 456 4 1 / 2 unit hinged to a post including access door Track See overleaf 120 Bracket (face fix) See overleaf I/250 2 120SN hinges 15 90X50FhSS Guide 2 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 4 401 Flush Bolt 4 456 5 1 / 2 Leaf unit hinged to post Track See overleaf 120 Bracket (face fix) See overleaf I/250 3 120SN hinges 18 90X50FhSS Guides 3 5G/904 Channel See overleaf 904a, 904B, 904P & 904Pa Flush Pulls 4 401 Flush Bolt 4 456 DaTa ShEET D130
GUIDE TO QUaNTITIES For top hung interior folding partitions on Centrefold 20 track system 2 Additional Leaves to increase 5 or 5½ Leaf units to 7 or 7½ Leaf units 1 120SN 120SN hinges 6 90 x 50FhSS 90 x 50FhSS Guide 1 5G/904 5G/904 Flush Pull 1 401 401 Flush Bolt 1 456 456 TRaCK and ChaNNEL Choose sufficient track and channel to cover the overall opening width. BRaCKET SPaCING (FaCE FIX) Place a bracket at each end of the track, at each join in the track, at 300mm from the post to which a unit folds and with the remaining brackets spaced symmetrically between the other brackets at not more than 900mm centres. Overall width of Leaves (plus reveal if unit floating Track lengths Brackets Channel clear of opening) 2000 1 x 1000 4 1 x 2000 3000 1 x 3000 5 1 x 3000 4000 1 x 4000 7 1 x 4000 5000 1 x 5000 8 1 x 5000 6000 1 x 6000 9 1 x 6000 7000 1 x 3000 11 1 x 3000 1 x 4000 1 x 4000 8000 2 x 4000 13 2 x 4000 assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D130B
GUIDE TO QUaNTITIES For top hung interior folding partitions on Centrefold 45 & 75 track systems This Guide to Quantities is only applicable to Data Sheets D160. SPECIFICaTIONS and QUaNTITIES The specifications below and overleaf detail the maximum and minimum capacities for the track systems recommended. Determine the number of leaves required to cover the opening. The leaves are hinged together to form units of up to seven full leaves and one half leaf hinged to a post. wider openings can be covered by including units floating to either side of the opening. Floating units consist of five, seven or nine full leaves. If the leaf weight is unknown, the weight can be calculated using the chart in Section a. having calculated the weight, use the information below to select the appropriate track system and quantities for the unit or units required to cover the opening width. Specification for Individual Leaves Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 900mm 1000mm Min Leaf Thickness 35mm 44mm Track System Centrefold 45 Centrefold 75 Refer to Data Sheet D160 D160 1½ Leaf unit hinged to post Quantities Reference Numbers Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 1 45CF/4 75CF/4 hinges 6* 100X75LPSS 100X75LPSS Channel See overleaf 6G/904 6G/904 Flush Pulls 2 401 401 Flush Bolt 2 456 456 *For Leaves over 2400mm high increase to 8 2½ Leaf unit hinged to post including access door Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 1 45CF/4 75CF/4 hinges 9* 100X75LPSS 100X75LPSS Guide 1 6G/904 6G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 3 401 401 Flush Bolt 3 456 456 *For Leaves over 2400mm high increase to 12 3½ Leaf unit hinged to a post Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 2 45CF/4 75CF/4 hinges 12* 100X75LPSS 100X75LPSS Guides 2 6G/904 6G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 3 401 401 Flush Bolt 3 456 456 *For Leaves over 2400mm high increase to 16 4½ unit hinged to a post Track See overleaf 120 250 Bracket (face fix) See overleaf 1/250 1/250 2 45CF/4 75CF/4 hinges 15* 100X75LPSS 100X75LPSS Guide 2 6G/904 6G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 4 401 401 Flush Bolt 4 456 456 *For Leaves over 2400mm high increase to 20 5½ Leaf unit floating to either side Track See overleaf 180 250 Bracket (face fix) See overleaf 1/250 1/250 3 45CF/4 75CF/4 hinges 12* 100X75LPSS 100X75LPSS Guides 3 6G/904 6G/904 Channel See overleaf 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 4 401 401 Flush Bolt 4 456 456 *For Leaves over 2400mm high increase to 16 DaTa ShEET D140
GUIDE TO QUaNTITIES For top hung interior folding partitions on Centrefold 45 & 75 track systems Specification for Individual Leaves Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 920mm 1000mm Min Leaf Thickness 35mm 44mm Track System Centrefold 45 Centrefold 75 Refer to Data Sheet D160 D160 5½ Leaf unit hinged to post Quantities Reference Numbers Track See below 180 250 Bracket (face fix) See below 1/250 1/250 s 3 45CF/4 75CF/4 hinges 18* 100X75LPSS 100X75LPSS Guides 3 6G/904 6G/904 Channel See below 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 4 401 401 Flush Bolt 4 456 456 *For Leaves exceeding 2400mm high increase to 24 6½ Leaf unit hinged to post Track See below 180 250 Bracket (face fix) See below 1/250 1/250 s 3 45CF/4 75CF/4 hinges 21* 100X75LPSS 100X75LPSS Guides 3 6G/904 6G/904 Channel See below 904a, 904B, 904P & 904Pa 904a, 904B, 904P & 904Pa Flush Pulls 5 401 401 Flush Bolt 5 456 456 *For Leaves exceeding 2400mm high increase to 28 The quantities for seven or eight leaves pivoted to one side or for eight leaves floating to either side can be calculated by adding the quantities below for two leaves to the previously shown quantities of five leaves pivoted to one side, six leaves pivoted to one side or six floating leaves respectively. 2 Additional Leaves to increase 5½ or 5 Leaf units to 7½ or 7 Leaf units 1 45CF/4 75CF/4 hinges 6* 100X75LPSS 100X75LPSS Guide 1 6G/904 6G/904 Flush Pull 1 401 401 Flush Bolt 1 456 456 *For Leaves exceeding 2400mm high increase to 8 TRaCK and ChaNNEL Choose sufficient track and channel to cover the overall opening width. BRaCKET SPaCING (FaCE FIX) Place a bracket at each end of the track, at each join in the track, at 300mm from the post to which a unit folds and with the remaining brackets spaced symmetrically between the other brackets at not more than 900mm centres. Overall width of Leaves (plus reveal if unit floating Track lengths Brackets Channel clear of opening) 2000 1 x 1000 4 1 x 2000 3000 1 x 3000 5 1 x 3000 4000 1 x 4000 7 1 x 4000 5000 1 x 5000 8 1 x 5000 6000 1 x 6000 9 1 x 6000 7000 1 x 3000 11 1 x 3000 1 x 4000 1 x 4000 8000 2 x 4000 13 2 x 4000 assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D140B
CENTREFOLD 20 For top hung interior centre folding partitions. Max 20kg each leaf. application Suitable for residential or light commercial centre folding partitions Leaves are hung centrally under the lintel and can fold to one or both sides of the opening To cover any width of opening, any number of folding units can be used DOOR SPECIFICaTION Track System: Centrefold 20 For Individual Leaves: Max Leaf height 2400mm Max Leaf weight 20kg Max Leaf width 900mm Min Leaf Thickness 35-50mm Folding units of up to five full leaves and one half leaf can be hinged to a post. Floating units consist of five full leaves. access should be through a separate door hinged to a post. Instruction on leaf width calculation is shown overleaf. Clearance between leaves to be 2mm minimum. Door leaves should be constructed to provide secure fitting for s, hinges and guides and can be flush, panelled or glazed. hardware SPECIFICaTION Track: 120 Material aluminium, Mill or Clear anodised Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Bracket: Bracket 316 Stainless Steel 1/250 Fit at 900mm maximum centres. Fit additional bracket where folding units stack and at the ends of the track. Hanger: 120SN alternative 80SN s are fitted with nylon tyre wheels on ball race bearings. Vertical adjustment is simple and positive. Guide: 5G/904 Guide incorporates a precision bearing. all steel parts to s and guides are stainless steel. Hinge: Butt hinge 90x50mm 90x50FhSS Channels: aluminium 904a Brass 904B Polypropylene & aluminium 904Pa Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Finish aluminium - Mill or Clear anodised Accessories: Flush Pulls and Flush Bolts. Finish: PvD Brass, Satin Nickel No. 120SN No. 80SN 1/250 Bracket No. 20DS Door Stop No. 401 Flush Pull 105 x 41 with 11 mortise No. 5G/904 Guide No. 90x50FhSS hinge DaTa ShEET D150
16 Thick Timber Pad Door preparation for 120SN No. 120SN No. 120 Track No. 20DS Door Stop No. 120SN See detail at left for attachment details Floor Fit hinges 3.5 offset to centre of Pin No. 904Pa Polypropylene & aluminium Support Channel recessed into Floor No. 5G/904 Guide 90x50FhSS Butt hinge No. 282SS hinge To provide an opening for maintenance, mount Track 40mm off face of Jamb Post 120 Track No. 282SS hinge No. 401 Flush Pull access Door No. 282SS hinge Channel No. 401 Flush Pull Jamb 90x50FhSS hinge NOT TO SCaLE No. 401 Flush Pull HINGEd TO JAMB LEAF WIdTH CALCULATIONS No. 401 Flush Pull No. 5G/904 Guide Floor No. 904Pa Polypropylene & aluminium Support Channel recessed into Floor assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D150B
CENTREFOLD 45 & 75 For top hung interior centre folding partitions. Max 75kg each leaf. application Suitable for residential or commercial centre folding partitions Leaves are hung centrally under the lintel and can fold to one or both sides of the opening To cover any width of opening, any number of folding units can be used DOOR SPECIFICaTION Track System: Centrefold 45 Centrefold 75 For Individual Leaves: Max Leaf height 3000mm 3300mm Max Leaf weight 45kg 75kg Max Leaf width 920mm 920mm Min Leaf Thickness 35mm 44mm Folding units of up to seven full leaves and one half leaf can be hinged to a post. Floating units consist of five, seven or nine full leaves. access should be through either a separate door hinged to a post. Instruction on leaf width calculation is shown overleaf. Clearance between leaves to be 2mm minimum. Door leaves should be constructed to provide secure fitting for s, hinges and guides and can be flush, panelled or glazed. hardware SPECIFICaTION Track: 180 250 Material aluminium aluminium Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Bracket: Bracket 316 Stainless Steel 1/250 1/250 Fit at 900mm maximum centres. Fit additional bracket where folding units stack and at the ends of the track. Hanger: 45CF/4 75CF/4 s are fitted with nylon tyre wheels on ball race bearings. Vertical adjustment is simple and positive. Guide: 6G/904 6G/904 Guide incorporates a precision bearing. all steel parts to s and guides are stainless steel. Hinge: Butt hinge 100 x 75LPSS 100 x 75LPSS Channels: aluminium 904a 904a Brass 904B 904B Polypropylene & alum. Support 904Pa 904Pa Standard lengths 2000mm, 3000mm, 4000mm and 6000mm Accessories: Flush Pulls and Flush Bolts. Finish: PvD Brass, Satin Nickel No. 45CF/4 & 75CF/4 No. 401 Flush Pull. 105 x 41 with 11 mortice. available in satin & stainless steel or PvD brass 1/250 Bracket 100 x 75 Butt hinge No. 6G/904 Guide Flush Bolt - 190 x 41 with 10 mortice and 20 throw DaTa ShEET D160
Fixing for all brackets, M8 bolts or coach screws 16 thick Timber Pad No. 180 Track M6 Bolt with washer and captive nut No. 1/250 Bracket No. 250 Track 45CF/4 & 75CF/4 No. PS13B or PS16B Brush Seal Note: s and guides are fitted to alternate leaves only. Bore hole for 27 diameter x 36 to allow bolt to withdraw with vertical adjustment Fit hinges 6 offset to centre of pin except those on leaf hinged to post see below. 6G/904 Guide view SHOWING ALTERNATIvE NO. 250 TRACK ANd 1/250 BRACKET FORMULA FOR LEAF WIdTH CALCULATIONS all leaves are the same width, hinge pin to hinge pin centres. Except a leaf hinged to a post, which must be half the width of a full leaf less half the leaf thickness. If the stiles are being rebated, the leaves will have to be made wider than calculated to allow for the rebating. The formula for calculating the width of leaves for a partition 44 thick is as follows - add 22 (half leaf thickness) to the width between the rebated posts for each leaf hinged to a post and divide the result by the number of leaves. I.E. for three and a half leaves, divide by 3.5. This gives the width of the full leaves. The leaf higned to the post is half the full leaf width less 22. Deduct 2 from each measurement for clearances. For example, 2 units of 3 1/2 leaves 44 thick, each hinged to opposite posts, with 6186 overall between posts - (6186 + 22 + 22) / 7 = 890 less 2 = 888 for width of wider leaves. 890 divided by 2 = 445 less 22 less 2 = 421 for width of leaves hinged to posts. 100 x 75 Butt hinge Fitt butt hinges to post as shown with no offset Offset of tongue, groove and butt hinges, avoids the cutting of tongues Central tongues must be cut around butt hinges NOT TO SCaLE PLAN 1 PLAN 2 5½ Leaves hinged to Post as Plan 1 3½ Leaves hinged to Post as Plan 2 half leaf thickness Centre line of track 6 Min. Clearance 6G/904 Guide Note: No offset to hinges on post fit pin centre flush with face of leaf Tongue and groove joints these joints, with hardwood tongues are recommended Rebated joints if rebating is preferred it must be to layout above No. 904P polypropylene channel 904Pa Polypropylene channel & aluminium support channel aluminium support channel 904Pa polypropylene channel and aluminium support channel in reversible sill assa abloy New zealand Ltd. PO Box 100407, North Shore North Shore City 0745 6 armstrong Road, albany North Shore City 0632 New zealand Tel +64 9 415 7888 Fax 0800 478 297 www.assaabloy.co.nz DaTa ShEET D160B