Commercial Sliding Door Hardware. Design in Motion

Transcription

1 Commercial Sliding Door Hardware Design in Motion November 12

2 Contents Introduction 2 Straight Sliding Systems 3 Pacer - timber and metal doors up to 0kg 4 Sirocco timber and metal doors up to 80kg 6 Sienna timber doors up to 1kg 8 Soltaire timber and metal doors up to 0kg 10 Flexirol - timber and metal doors up to 00kg 12 Folding Systems 14 Securefold exterior folding timber doors up to 100kg 16 Securefold Ultra exterior folding timber doors up to 100kg 18 Pacer interior centre-folding timber doors up to 7kg INTRODUCTION PC Henderson has long been acknowledged as the world leader in the design and manufacture of sliding and folding door hardware systems for residential, commercial and industrial applications. Established in 19, PC Henderson is based in Bowburn in North East England and has subsidiaries in Holland and Ireland. The company has a long established sales and distribution network in over 70 countries, supported by Henderson s fully trained UK based technical sales team. The company is committed to quality and is registered to BS EN ISO 9001: 08 Quality Systems and Environmental Management System ISO 101: 04 As part of this commitment this brochure has been printed on carbon neutral paper in line with the FSC which promotes responsible management of the world s forests. This accreditation guarantees that only the amount of wood which the forest can regenerate naturally is cut down with minimal impact on the environment, wildlife and the indigenous people who reside there. Pacer interior end-folding timber doors up to 6kg 22 Pacer exterior end-folding timber and aluminium doors up to 6kg Flexirol interior centre-folding timber doors up to 1kg 28 Flexirol interior end-folding timber doors up to 1kg 30 Flexirol exterior end-folding timber doors up to 1kg 32 Flexirol exterior end-folding aluminium doors up to 1kg 34 Multidirectional Systems 36 Flexirol 90º - timber and aluminium doors up to 100kg Flexirol 13º - timber and aluminium doors up to 00kg Components 42 Guide to Quantities 49 2

3 COMMERCIAL RANGE The models in the Henderson commercial range are suitable for doors weighing up to 00kg. They are ideal for applications such as shop fronts, hotels, conference centres and offices, where smooth action, high performance and aesthetics are important. You can choose from timber, aluminium and glass door options*, with straight sliding, folding and multidirectional stacking systems. Flexirol multidirectional systems can accommodate 90º and 13º movement. Aluminium track can be painted on site to match interior colours and ceilings. Pacer track has the option of clip-on aluminium fascia. STRAIGHT SLIDING DOOR SYSTEMS The main advantage of using a straight sliding system is that it saves room space, as the door does not require a swing or stacking space to open. Using straight sliding systems therefore makes perfect sense when space is at a premium. Sliding doors also offer a touch of individuality to a room design. P C Henderson s commercial range of straight sliding door systems covers door weights up to 00kg. The products in this range have all been designed for high performance with particular attention to aesthetic appearance. With this goal in mind, Husky and Pacer straight sliding systems have been designed to accommodate a range of clip-on aluminium fascia also supplied by P C Henderson. This aluminium fascia is supplied as standard in a satin anodised finish, with other finishes available on request. In today s modern working environment the use of glass as an important design element has become widespread practice. *For further details see our Glass door hardware systems brochure. 3

4 PACER STRAIGHT SLIDING FOR TOP-HUNG TIMBER AND METAL DOORS 14 Bracket 1B Hole 9mm 72 7B 4 Track 600 6BX 6B DIA (assumed 0mm box section) Adjustment Nut Hole Required Ø 11mm (assumed mm section) Hole Required Ø 11mm Lock Nut 18 Adjustment Nut 11 DIA Lock Nut Fascia F0 Fascia F160 Door Thickness 3-0 Removable Roller Guide 104NX/94 Hole Required for Fixing Guide is Ø 17mm Removable Roller Guide 104N/94 Roller Guide 106N/ Patent Washer Fixing Lug Threshold 94T Channel 94(X) 17 4

5 CAPACITY e e Maximum door weight: Maximum door height: Door thickness: 0kg 3000mm 3mm-46mm ole Required Fixing Guide is Ø 17mm Removable Roller Guide APPLICATIONS104N/94 Combining performance Threshold and style 94T with versatility, Pacer straight sliding in timber, aluminium or metal is ideally Fixing Lugsuited to the modern arena of shop fronts, offices and other stylish interiors. 17 7B Retaining Stop 601P 2B 6BX 6B DOOR TYPES Timber doors for interior applications can be either solid or glazed. Metal doors can be of angle or box section. Aluminium is dependent on extrusion profile. Bracket TECHNICAL 14 1B INFORMATION Hole 9mm Track: Anodised aluminium & mill finish options B DIA Door Thickness 3-0 Track 600 Available 4 in 00mm, 00mm, 6BX 3000mm, 6B 300mm, 00mm and 6000mm lengths (assumed 0mm box section) (assumed mm section) Brackets: Face fix 1B 18 Adjustment 30 Nut Hole Required Jointing bracket Ø 11mm 1BX Hole Required Lock Nut Ø 11mm Fascia Fascia F160 finish F0in lengths of 00mm, 00mm, Hole Required for Fixing Guide is Ø 17mm Adjustment Nut Fascias: 11 Soffit fixed track Lock Nut F160 with standard return DIA Face fixed track Fascia comes in a satin anodised aluminium 3000mm, 300mm, 00mm and 6100mm F0 with standard return s: Wood doors 7B - concealed fixing Wood doors 2B - angle plate fixing Aluminium/Metal doors 7B - concealed fixing Metal doors Removable Roller Guide 104NX/94 6B - angle frame Metal doors 6BX - box frame Removable Roller Guide 104N/94 Threshold 94T Guides: Wood/Aluminium/Metal doors 89/2N - floor mounted Patent Washer guide Roller Guide Fixing 106N/ Lug Wood/Aluminium doors 106N/94 - concealed fixing 17 Channel Metal 94(X) doors 104N/94 - angle frame Metal doors 104NX/94 - box frame B Flush Pull 0 Flush Bolt F371 7B Retaining Stop 601P Guide 106N 2B 100 6BX 2B Track 600 Guide Channel 94(X) 6B Bracket 1B Clip Stop 601P Guide Channel: Brass 94 Aluminium 94X Aluminium threshold/guide channel 94T 94 channel available in 100mm and 3000mm lengths. 94X channel available in 100mm, 00mm, 00mm, 3000mm lengths. Aluminium threshold available in 00mm, 00mm, 3000mm, 300mm, 00mm and 6000mm lengths. Accessories: Retaining stop mounted within the track 601P Flushbolt (lockable & non-lockable versions) SF190

6 SELF CLOSING SIROCCO FOR METAL OR TIMBER DOORS Min. 46 Max. 800 Min. 10 Max (SIRLH left hand opening shown) 68 Sirocco fascia (SIRFAS) 6

7 CAPACITY TECHNICAL INFORMATION Maximum door weight: Minimum door thickness: Maximum door thickness: Minimum door width: Maximum door width: APPLICATIONS 80kg 30mm 46mm 800mm 10mm Application Right Hand Opening Left Hand Opening Optional Delayed Closing timer RH Optional Delayed Closing timer LH Optional Fascia Product code SIRRH SIRLH DELRH DELLH SIRFAS The Sirocco system is a quiet, user friendly self closing system which brings the door leaf gently to a close. The integrated hydraulic soft stop brings the door to a safe and cushioned close making it ideal for disabled access systems or public areas. The internal door brake can also be adjusted to allow the user to dictate the speed of opening preventing damage to the door and system. Designed to give a smooth and quiet operation Adjustable closing speed feature Optional hold open unit giving adjustable time delay before closing Operational between temperatures of -10 C and C Accessories: Brake to reduce opening speed to prevent damage to the door and system Hold open unit giving adjustable time delay before self closing DOOR TYPES Timber doors for interior applications only. Opening brake rack Opening door stop Optional delayed timer Closing brake rack Aluminium track Opening door stop Closing door stop Hydraulic control unit Power spring unit Door 7

8 STRAIGHT SLIDING SIENNA FOR TIMBER DOORS = 30 = Standard Bar No. of Fixing Plates/Brackets 00mm 4 00mm 3000mm 6 300mm 7 00mm 8 000mm

9 CAPACITY Maximum door panel weight: Minimum door panel thickness: Maximum door panel thickness: Maximum door panel height: Minimum door panel width: 1kg 30mm 70mm 00mm 700mm APPLICATIONS The straight sliding Sienna system is an elegant frameless timber door system that creates a minimalist look. It is designed to accommodate doors of 30-70mm thickness and a weight capacity of 1kg. Rollers are engineered to run effortlessly along a brushed stainless steel tubular track Stops are positioned on the track to limit the door travel DOOR TYPES Sliding frameless timber doors. TECHNICAL INFORMATION Basic Kit 2 hangers, 2 door stops, one guide, 2 bar end caps SN1T Track/brackets: Ømm stainless steel tubular track /****T (Replace **** with length of track required) Available in standard lengths up to 6m, drilled and pre-assembled with the correct number of wall brackets (see page 8) Guide: Floor guide 101SS Door Stop: Stop /UDS Handle: Please contact our technical sales team for details on handles mm Opening height (OH) Door height (DH) DH = OH mm 00mm maximum Opening width (OW) Panel width (PW) PW = OW + 80mm

10 STRAIGHT SLIDING SOLTAIRE FOR TIMBER AND METAL DOORS minimum 24 maximum 12 minimum 32 maximum 12 minimum 28 maximum minimum* 48 maximum 3 minimum 48 maximum 3 minimum 48 maximum 3 minimum 10 maximum 3 minimum 10 maximum 3 minimum 10 maximum 94/94X channel 94/94X channel 94/94X channel *For MDF doors 19-23mm you must use hanger 2/1/SS and for doors there is an option of surface mounted or routed (1/1/SS or 7/1/SS) 10

11 CAPACITY Maximum panel weight 1 kg 180 kg 0 kg Maximum panel thickness 48mm 48mm 48mm Minimum panel thickness 19mm* 3mm 3mm Maximum panel height 3000mm 3000mm 3300mm APPLICATIONS Soltaire is a top hung straight sliding system designed to accommodate interior and exterior doors of one sliding panel or two bi-parting doors on a single track. Designed for door weights of up to 1kg, 180kg or 0kg the reliable system is extremely durable and ideal for coastal applications, heavy use or areas that require a high level of corrosion resistance. Manufactured from high grade 316 stainless steel with anodised aluminum track. s available for MDF (1kg only), timber or metal doors. The track can be soffit fixed or face fixed to give flexibility of installation. DOOR TYPES Timber and metal doors of either angle frame or box section and aluminium extrusion. TECHNICAL INFORMATION Track: Anodised aluminium ( microns) 1/00,1/00, 180/00,180/00, 0/00,0/00, available in lengths 1/3000,1/00, 180/3000,180/00, 0/3000,0/00, 1/000 & 1/ /000 & 180/6000 0/000 & 0/6000 Soffit fix spacing centres (maximum) 600mm 900mm 900mm Brush strips: Available in black in 4 brush heights, by the metre BS10, BS1, BS, BS(mm) Brackets: Face fixed stainless steel 1/SS 1/SS 1/SS Double run face fixed stainless steel /SS H/SS H/SS Starting mm from end of track fix at 600mm centres (maximum) s: 2 required per door MDF doors - face fixing 2/1/SS Timber doors - top fixed - surface mounted 1/1/SS - (concealed) plate fixing 7/180/SS - corner plate fixing 7/1/SS 2/180/SS 7/0/SS - saddle plate fixing 3/180/SS 3/0/SS Metal doors - angle frame door fixing 6/1/SS 6/180/SS 6/0/SS - box frame fixing 6X/180/SS 6X/0/SS - (concealed) plate fixing 7/180/SS 7/0/SS Guides: - (concealed) fixing with SS bearing 106 SS/94 106H SS/94 106H SS/94 - nylon saw cut guide 102 N - wall mounted guide 102 SS/ SS/ SS/94 - metal door angle frame guide 104 P/89 - box section metal door 104 PX/ PX/ PX/89 - for multiple runs of doors use 102 SS/ SS/ SS/94 Channels: Aluminum (00, 00, 3000 & 6000mm lengths) 94X 94X 94X Brass (100 & 3000mm length only) Stainless steel (3000mm length only) 89SS 89SS 89SS Polypropylene channel 94P 94P 94P Aluminum supporting channel for polypropylene 94SC 94SC 94SC Track Stop: HH4/SS HH/SS HH/SS Flushbolts: SF190 SF190 SF190 11

12 FLEXIROL STRAIGHT SLIDING FOR TOP-HUNG TIMBER AND METAL DOORS Face Fix Bracket 1A/0 Suspended Ceiling Bracket with Vertical Adjustment 3S/0 Slotted Hole 12x30 Hole to Lock Slotted Hole 12x Lock Nut Lock Nut Track 0 6/7 Horizontal Adjustment Adjustable Nut Lock Nut DIA 18 DIA 0 Lock Nut Threaded Hole M Roller Guide 106N/94 Channel 94(X) Guide 89/2N 8-13 Channel 94(X) 12

13 CAPACITY Maximum door weight: 00kg (6 hanger) Maximum door height: 6000mm - timber or metal framed Maximum door width: 6000mm - timber or metal framed Door thickness: -100mm - timber or metal framed HH3/301 Track Stop X Face Fix Bracket 1A/0 Track 0 APPLICATIONS Henderson straight sliding Flexirol is ideally suited to hotels, conference centres, shop-fronts, showrooms or any site that requires high performance and attractive finish. Flush Pull 0 6/7 6/2 DOOR TYPES 100 Timber and metal doors of either angle frame or box section and aluminium extrusion. Flush Bolt F371 Guide 106N/94 Channel 94(X) TECHNICAL INFORMATION Track: 0 (see components section for range of finishes) Brackets: Face fix 1A/0 Soffit fix 3S/0 s: Metal doors 6 Timber doors 6/7 - concealed fixing Timber doors 6/2 - angle plate fixing Guides: Timber and metal doors 89/2N Timber doors 106N/94 Metal doors 104N/94 Metal doors, extended version 104NX/94 Guide Channel: Brass 94 Aluminium 94X Aluminium threshold/guide channel 94T (refer to page ) Accessories: Flushpull 0 Flushbolt SF190, and 600 Narrow bolt and keep F371 & F3734 Trackstop HH3/301 13

14 14

15 SECUREFOLD, PACER & FLEXIROL FOLDING DOOR SYSTEMS The use of folding doors is ideal for interior and, in particular, exterior situations where space is limited or where it is desirable to have the door leaves stacked behind a reveal. With the Securefold, Pacer and Flexirol folding door systems, flexibility is the key. The range covers everything from internal folding partitions to exterior folding entrance ways. The Pacer system covers weights up to 7kg per door leaf, Securefold up to 100kg and the Flexirol system has a capacity of up to 1kg. All systems use high performance components that are extremely durable, ensuring a long, trouble-free operating life. When considering internal partition systems, specifiers are provided with the option of either centrefold or endfold configurations. To match the variety of materials used in modern day design, Pacer and Flexirol folding systems cater for doors of glass, timber or metal construction with Securefold specialising as a weatherproof system for timber doors. 1

16 EXTERIOR FOLDING SECUREFOLD FOR TIMBER DOORS Track fixing (Not by PC Henderson) 2 1mm gap each side for movement between 2 different materials. Fill with clear silicon sealant Track 0 PACKING BATTEN THICKNESS 12mm less than door thickness BS10B Brush Seal Intermediate Set Kit SF4 JAMB CAP IN LINE WITH TRACK AQ63B Seal : AQB Seal AQ63B Seal (cut around the hinges) Offset Hinge Set SF7 AQ63B Seal : Pivot Set SF1 Intermediate Set SF4 End Set SF2 Hinge Handle Jamb Rebate Offset 8mm Channel Intermediate Set SF4 Centre line of channel This gap can be reduced to mm if doors are made 4mm longer and bottom of pivot/guides are locally checked in Pivot Set SF1 Jamb Leaf Intermediate Leaf Intermediate Leaf End Leaf Centre line of hanger guide pivot and track End Set SF2 19 Ø10mm drill for drainage at 1000mm centres, 300mm centres for extreme weather conditions POLYPROPYLENE CHANNEL 94P When used in conjunction with aluminium support channel 94SC the outer channel dimensions become 23H x W Offset Hinge Set SF7 Offset Hinge Set SF7 JAMB CAP IN LINE WITH TRACK Jamb Cap Gasket Alternative aluminium threshold SF94T by PCH - Comes complete with 94P and endcaps and is predrilled for drainage Please contact our technical sales team for further details on Securefold Non-Mortice and Aluminium options. 16

17 CAPACITY Maximum door height: 3300mm Maximum door weight: 100kg Maximum door width: 1000mm Maximum door thickness: 3-68mm* * For doors between 3-44mm use an alternative to standard Flushbolt Pivot Set Kit SF1 Intermediate Set Kit SF4 End Set Kit SF2 APPLICATIONS Securefold is the ultimate in exterior folding systems and opens up design to a wealth of new possibilities. The Securefold system has been designed to maximise the flexibility of a room s living space, removing barriers and enabling the user to have an indoor/outdoor experience by fully opening up exterior walls. The system which operates with effortless ease combines the benefits of folding doors with the ability to keep out the weather with no corrosion worries. This modern, contemporary feature will increase available living space whilst allowing natural light to envelope a room. SF7 Offset Hinge Set OUTSIDE SF7 Offset Hinge Set DOOR TYPES Residential and commercial timber doors. TECHNICAL INFORMATION Track: 0 Material: Anodised aluminium (anodising microns) Standard lengths: 00, 00, 3000, 300, 00, 000 and 6000mm /Hinge/Guide sets: Pivot set SF1 End hanger guide set left hand* SF2L End hanger guide set right hand* SF2R Hinge set with handle SF3 Intermediate hanger/hinge/guide set SF4 Hinge set inward opening SF Hinge set offset inward opening SF6 Hinge set offset outward opening SF7 Rebated end hanger/guide set** SF8 Intermediate pivot hinge*** SF9 Face fix handle (optional) SF10 Aluminium threshold SF94T Channel: Polypropylene guide channel 94P anodised aluminium support channel 94SC Threshold channel lengths correspond with standard track lengths. Seals: Door perimeter seal brown AQ63B Frame perimeter seal brown AQB Brush seal-black BS10B Accessories: Lockable and non-lockable Flushbolts available 190, & 600mm in gold, satin & chrome finish NOTE: * End hanger/guide sets are handed inside looking out. ** End hanger set for a pair of rebated meeting doors. *** Intermediate pivot hinge for doors above 20mm 17

18 EXTERIOR FOLDING SECUREFOLD ULTRA FOR TIMBER DOORS Track fixing (Not by PC Henderson) 2 1mm gap each side for movement between 2 different materials. Fill with clear silicon sealant PACKING BATTEN THICKNESS 12mm less than door thickness Track 0 BS10B Brush Seal Intermediate Set Kit SF4 JAMB CAP IN LINE WITH TRACK 12 3 AQ63B Seal :2 6 AQB Seal AQ63B Seal (cut around the hinges) AQ63B Seal :2 Hinge Handle Offset 8mm 23 3 Pivot Set SFU1 4 Wheel Set SFU This gap can be reduced to mm if doors are made 4mm longer and bottom of pivot/guides are locally checked in Ø10mm drill for drainage at 1000mm centres, 300mm centres for extreme weather conditions POLYPROPYLENE CHANNEL 94P When used in conjunction with aluminium support channel 94SC the outer channel dimensions become 23H x W JAMB CAP IN LINE WITH TRACK Jamb Cap Gasket Alternative aluminium threshold SF94T by PCH - Comes complete with 94P and endcaps and is predrilled for drainage 18

19 CAPACITY Maximum door height: Maximum door weight: Maximum door width: Maximum door thickness: 3300mm 100kg 1000mm 4-68mm APPLICATIONS Securefold Ultra has been tested to the European security standard BS EN 1627:11 and British standard PAS24. The additional components featured on Securefold Ultra all work together to give uncompromised security and weather resistance unlike any other system currently on the market today Enhanced anti-tamper screw system. Unique, inter-locking attack resistant hinges. 3 points of locking. Extruded aluminium flushbolt incorporating 10mm diameter 316 stainless steel bolt. DOOR TYPES Residential and commercial timber doors. TECHNICAL INFORMATION Track: 0 Material: Anodised aluminium (anodising microns) Standard lengths: 00, 00, 3000, 300, 00, 000 and 6000mm /Hinge/Guide sets: Pivot set SFU1 End hanger guide set left hand* SFU2L End hanger guide set right hand* SFU2R Hinge set with handle SF3 Intermediate hanger/hinge/guide set SFU4 Hinge set inward opening SF Hinge set offset inward opening SF6 Hinge set offset outward opening SF7 Rebated end hanger/guide set** SF8 Intermediate pivot hinge*** SFU9 Face fix handle (optional) SF10 Aluminium threshold SF94T Channel: Polypropylene guide channel 94P anodised aluminium support channel 94SC Threshold channel lengths correspond with standard track lengths. Seals: Door perimeter seal brown AQ63B Frame perimeter seal brown AQB Brush seal-black BS10B Accessories: Lockable flushbolts available 190, & 600mm in gold, satin & polished chrome finish NOTE: * End hanger/guide sets are handed inside looking out. ** End hanger set for a pair of rebated meeting doors. *** Intermediate pivot hinge for doors above 20mm Security screw Hinge bolt reinforcing plate Security screw SFU1 Integrated bridge plate with security screw to prevent removal of the strapbolt Unique central interlocking hinge leaf SFU4 Security hinge pin Security hinge pin 3mm reinforcing plate Security screw 10mm Ø Hinge bolt 3mm reinforcing plate 19

20 PACER INTERIOR CENTREFOLD FOR TIMBER DOORS 48 Track B -61B/ Drill Ø 12mm to 27mm Depth for Pendant Lock Nut Adjustable Nut Butts 3/2 100 x Guide 106N/94 Channel 94(X)

21 CAPACITY Maximum door weight: Maximum door height: Maximum door width: Door thickness: 3kg (61B hanger) 7kg (61B/4 hanger) 2700mm 900mm 3mm-44mm Note: No offset to butts on post Rebated Joints Plan 1 Plan 2 Plan 3 APPLICATIONS Top-hung Pacer gear and fittings for centre folding timber partition doors. Leaves are hung centrally and can fold to one or both sides. For applications hinged to the jamb, 3 1 /2, 1 /2 or 7 1 /2 leaves can be used with the half-leaf hinged to the jamb. For best operation of floating units,, 7 or 9 leaves should be used. Any access door should be hinged separately to the jamb. 61B C B 3 1 / 2 leaves hinged to post. As Plan 1 A Track 600 leaves floating folding. As Plan 2 61B/4 1 / 2 leaves hinged to post. As Plan 3 DOOR TYPES Residential and commercial timber doors. All full leaves are of equal width. A pivoting half-leaf (dimension C) is half the width of a full leaf (dimension A), less half of the leaf thickness (dimension B). TECHNICAL INFORMATION Track: Anodised aluminium & mill finish options 600 Available in 00mm, 00mm, 3000mm, 300mm, 00mm and 6000mm lengths Brackets: Face fix (fixed at 00mm intervals) 1B Jointing bracket 1BX s: Two-wheeled hanger 61B Four-wheeled hanger 61B/4 Guides: Nylon guide roller 106N/94 Guide Channel: Brass 94 Aluminium 94X Aluminium threshold/guide channel 94T 94 channel available in 100mm and 3000mm lengths. 94X channel available in 100mm, 00mm, 00mm, 3000mm lengths. Aluminium threshold available in 00mm, 00mm, 3000mm, 300mm, 00mm and 6000mm lengths. Hinges: Butt hinges - 100x 3/2 Accessories: Flushpull 0 Flushbolts SF190//600 Narrow bolt and keep F371 & F3734

22 PACER INTERIOR ENDFOLD FOR TIMBER DOORS Channel 94(X) Channel 94(X) Channel 94(X) 22

23 CAPACITY Plan 1 Plan 2 Plan Track 600 Top Pivot B/P Lock Nut Adjustable Nut Clearance 3mm B - (2 Wheels) APPLICATIONS Radius required: which side of door depends on swing direction Maximum door weight: 3kg (B hanger) Locking Bolt 6kg (B4 hanger) 6kg (BO/4 hanger) Maximum door height: 2700mm Maximum door width: 900mm Door thickness: 3mm-44mm 12 Ø mm Top View of Pivot B/P 4 leaves starting with pivot B/P B (2 Wheels) Pacer Endfold offers both two-wheeled and four-wheeled 1 hangers to cover a wide range of residential and commercial applications. Leaves can be hung to the left or the right of an opening, or hung as floating units. In applications using the fourwheeled hanger with an even number of leaves folding left and right meeting in the centre of the opening, an offset hanger (BO/4) is required (Plan 4). DOOR TYPES Residential and commercial timber doors. B/P B/4 (4 Wheels) Side to Open leaves starting with pivot No. is swing leaf 100 min Plan 4 4 leaves to either side starting with pivot Side to Open Side to Open Note: s and guides are to be fitted to alternate leaves only. B/P Pivot B/4 BO/4 Offset 6 leaves floating to left Side to Open TECHNICAL INFORMATION Hinged to Post Option 28 Bottom Pivot 3 Socket Ø mm Track: Anodised aluminium & mill finish options 600 Available in 00mm, 00mm, 3000mm, B 300mm, 00mm and 6000mm lengths 1 Brackets: Face fix (fixed at 00mm intervals) 1B Jointing bracket 1BX s: Two-wheeled hanger B B/4 B/ N/94 Situation Hinged to Post B/P 1 Four-wheeled hanger B/4 Channel Four-wheeled 94(X) offset hanger 13 BO/4 102 Note: track face fixed use bracket 1B - 1BX. See page 61. Pivots: For door widths between 3-44mm B/P Note: No offsets to butts on posts 12 B 1 B/P Even - /- mm Even Even - /- Half Door Thickness (A) X A Note: Butt hinges on posts are not offset K/P Bolt M6 13 All leaves are of equal width except the leaf hinged to the post. The dimension for the leaf hinged to the post (X) is, 1 A, less B (half the leaf thickness), less mm. A Formula: X=(A-B)-mm Ø 4 Guides: Nylon end guide roller N/94 Guide Channel: Brass 94 Aluminium 94X Aluminium threshold/guide channel 94T Hinges: Butt hinges - 100x 3/2 Accessories: Flushpull 0 Flushbolts SF190//600 Narrow bolt and keep F371 & F3734 Note: Using a pivot allows leaves to be of equal width. 23

24 PACER EXTERIOR ENDFOLD FOR TIMBER DOORS 48 Track B 4 4 Clearance 8 60 Double Sealed (Wind and Waterproof) Rubber Sealing not by PCH Cram Plate Nut Lock Nut Inside Outside Inside Outside Hinge 6B (mm or mm) 8 For Fixing Instructions See Flexirol page Lock Nut Hinge Sleeve Nut Guide 67B Double Sealed - (Wind and Waterproof) Angle Profile (not by PCH) Angle Profile (not by PCH) *Cut Version Not Standard or Supplied by PCH *94T Guide Channel 94(X) 24

25 CAPACITY Even X Even X Maximum door weight: 6kg Maximum door height: 3000mm Maximum door width: 900mm Door thickness: 3mm-0mm APPLICATIONS Top-hung Pacer gear for end folding exterior doors in timber. Pacer Endfold offers four-wheeled hangers with offset option to cover a wide range of residential and commercial applications. In applications using the four-wheeled hanger with an even number of leaves folding left and right meeting in the centre of the opening, an offset hanger is required. DOOR TYPES Residential and commercial timber doors. 6B Hinge All Doors of Same Width Opening Width Opening Width Outside Inside Swing Door 62BA with 6B Double Hinge 3 3 Track 600 TECHNICAL INFORMATION Track: Anodised aluminium & mill finish options 600 Available in 00mm, 00mm, 3000mm, 300mm, 00mm and 6000mm lengths F371 67BA Guide with 6B Double Hinge Brackets: Face fix (fixed at 00mm intervals) 1B Joining track 1BX *3 Doors Folding to the Left Channel 94(X) or 94T s: Even X Intermediate Even hanger for timber doors with X 148mm strapbolt, no hinge End hanger for timber doors with 104mm Opening Width strapbolt, no hinge Offset end hanger for all doors with Outside 114mm strapbolt, no hinge 62BA/148 63BA/104 63BOA/114 X X 1 Centre to Centre X Distance of Hinges is Always Even Opening Width Outside Guides: All Doors of Same Width Inside Intermediate guide for timber doors with 10mm spindle, no hinge End guide for Swing timber doors with Door 110mm spindle, no hinge Guide Channel: Brass Opening Width 94 Aluminium Track X Aluminium threshold/guide channel 94T 67BA/10 68BA/110 Track 600 A 42 B Note: Width of Door B is Door A + 1mm Opening Width Inside 6B Hinges: 62BA mm single hinge for timber doors 6B//1 with 6B Double mm double hinge for timber doors 6B/ Hinge mm single hinge for timber doors 3 3 6B//1 mm double hinge for timber doors 6B/ -mm double hinge for timber doors 6B/- 6B Hinge 63BOA Offset with Single Hinge 3 Accessories: Flushpull 0 67BA Guide Flushbolts with SF190//600 6B Double Narrow bolt and Hinge keep F371 & F3734 Aluminium F371 door mounting kit 60B F371 68BA Guide with Single Hinge Refer to page *3 for Doors hinge Folding installation. to the Left Channel 94(X) or 94T Hinges for hangers and guides must be ordered separately. Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides. *2 Doors Folding to the Left 94(X) or 94T * For other options see Guide to Quantities, pages 47-4

26 PACER EXTERIOR ENDFOLD FOR ALUMINIUM DOORS 48 Track 600 Track BA/0 with 6B Double Hinge (mm or mm) 130 Stainless Steel Strap Bolt Ø 12mm Doors not by PCH Nut Lock Nut Plastic Cover 67BA Guide with 6B Double Hinge 26 Channel 94(X) or Threshold 94T Outside Track 600 Inside 4 7mm Packer - S7 Plastic Cover Lock Nut 4 Nut Plan: 3 Doors Folding to the Right Ø 12mm 67BA/2 with 6B Hinge (mm or mm) Doors not by PCH 10 Stainless Steel Roller Guide Spindle Threshold 94T Swing Door Even Even 17 26

27 16 CAPACITY 4 Ø 16 7 Maximum door weight: 6kg 19 Maximum door height: Plan: 3 Doors Folding to the Right 3000mm Maximum door width: Door thickness: APPLICATIONS 900mm 3mm-0mm 6B Double Hinge (mm or mm) oors not by PCH Top-hung Pacer gear for end folding exterior doors in aluminium. Pacer Endfold offers four-wheeled hangers with an offset option to cover a wide range of residential S/7 Packer (optional) and commercial applications. In applications with an even number of leaves folding left and right meeting in the Swing Door centre of Even the opening, an offset Even hanger is required BA/2 DOOR TYPES Pacer Exterior Endfold is suitable for both residential and commercial aluminium doors. Fixing components are not supplied as standard for aluminium doors. 94(X) Alternative Guiding System TECHNICAL INFORMATION Track: Anodised aluminium & mill finish options 600 Available in 00mm, 00mm, 3000mm, 300mm, 00mm and 6000mm lengths Brackets: Face fix (fixed at 00mm intervals) 1B Joining track 1BX Squared Joint Mitred Joint *s: *Guides: Intermediate hanger for aluminium doors with no hinge 148mm/0mm strapbolt 62BA/148 62BA/0 End hanger for aluminium doors with no hinge 104mm/mm strapbolt 63BA/104 63BA/ Offset end hanger for all doors with no hinge 114mm strapbolt 63BOA/114 63BOA/114 Intermediate guide for aluminium doors with no hinge 10mm/2mm spindle 67BA/10 67BA/2 End guide for aluminium doors with no hinge 110mm/180mm spindle 68BA/110 68BA/180 Guide Channel: Brass 94 Aluminium 94X Aluminium threshold/guide channel 94T Hinges: mm single hinge for timber doors 6B//1 mm double hinge for timber doors 6B/ mm single hinge for timber doors 6B//1 mm double hinge for timber doors 6B/ -mm double hinge for timber doors 6B/- Accessories: Flushpull 0 Narrow bolt and keep F371 & F3734 Aluminium door mounting kit 60B 7mm packer S/7 (optional, depending on frame and track layout) Hinges for hangers and guides must be ordered separately. Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides. * All with stainless steel strapbolt/spindle. For aluminium doors use in conjunction with a 60B mounting kit. Consult with PCH Technical Department for extrusion compatibility. 27

28 FLEXIROL INTERIOR CENTREFOLD FOR TIMBER DOORS Suspended Ceiling Bracket with Vertical Adjustment 3S/ /61 73 Track Grub Screw Adjustable Nut 19 Drill Ø 18mm Hole 60mm Deep Butts 3/3 100 x 7 Note: No offset to butts on post Plan 1 A C B 3 1/2 leaves hinged to p As Plan 1 Guide 106N/94 Guide 106N/94 Channel 94X Channel 94(X ) 28

29 CAPACITY Maximum door weight: Maximum door height: Maximum door width: Door thickness: APPLICATIONS 1kg 0mm 10mm 43mm-7mm Note: No offset to butts on post Rebated Joints Plan 1 Plan 2 Plan 3 Top-hung Flexirol gear and fittings for centre folding timber partition doors. Leaves are hung centrally and can fold to one or both sides. For applications hinged to the jamb, 3 1 /2, 1 /2 or 7 1 /2 leaves can be used with the half-leaf hinged to the jamb. For best operation of floating units,, 7 or 9 leaves should be used. Any access door should be hinged separately to the jamb. A C Track 0 A DOOR TYPES Heavy commercial timber doors. TECHNICAL INFORMATION Track: Guide 106N/94 0 (see components section for range of finishes) Channel 94(X ) Brackets: Face fix (fixed at 00mm intervals) 1A/0 Soffit fix 3S/0 B 3 1 /2 leaves hinged to post. As Plan 1 leaves floating folding. As Plan 2 All full leaves are of equal width. A pivoting half-leaf (dimension C) is half the width of a full leaf (dimension A), less half of the leaf thickness (dimension B). Note: s and guides are to be fitted to alternate leaves only. 1 /2 leaves hinged to post. As Plan 3 s: Timber doors 6/61 Guides: Nylon roller guide 106N/94 Guide Channel: Brass 94 Aluminium 94X Aluminium threshold/guide channel 94T Hinges: Butt hinges - 100x7 3/3 Accessories: Flushpull 0 Flushbolts SF190//600 Narrow bolt and keep F371 & F

30 17 FLEXIROL INTERIOR ENDFOLD FOR TIMBER DOORS 6/ 98 Top Pivot /0P P 73 Locking Bolt Adjustable Nut Grub Screw Drill Ø 18mm Hole 60mm Deep Drill Ø 18mm Hole 60mm Deep 4 Clearance 3mm /0P 6/ Butts 3/3 100x7 Radius required: which side depends on swing direction Ø 6.mm Door Thickness 43-7 Top View of Pivot /0P Guide R/94 4 6/ Channel 94(X) 28 Bottom Pivot 3 Socket Ø Channel 94(X) Note: No offs butts on 30

31 Top Pivot /0P CAPACITY Plan 1 Plan 2 Plan Locking Bolt Maximum door weight: Maximum door height: Maximum door width: Door thickness: 1kg 0mm 10mm 43mm-7mm 4 4 Leaves Starting with Pivot Leaves Starting with Pivot No. is Swing Leaf 100 min 6 Leaves Floating to Left 4 4 Clearance 3mm APPLICATIONS Top-hung Flexirol gear and fittings for end folding timber partition doors. Leaves can be hung to the left or right of an opening or hung as floating units. DOOR TYPES /0P 6/ Side to Open Plan 4 4 Leaves to Either Side Starting with Pivots Side to Open Side to Open Bottom Pivot 3 Socket Ø Radius required: which side depends on swing direction 4 Heavy commercial timber doors. Ø 6.mm TECHNICAL INFORMATION Top View of Pivot /0P Track: 0 (see component section for range of finishes) 19 3 Note: s and guides are to be fitted to alternate leaves only. Brackets: Face fix 1A/0 (fixed at 00mm max.intervals) R/94 (Bottom) 7 Soffit fix 3S/0 /0P Hinged to Post 14Option 12 4 s: Timber doors 6/ (Top) 6/ /0P Pivots: Timber doors /0P B 4 Ø 4 X A Guides: Brass end guide roller R/ Note: Butt hinges on posts are not offset 74 Ø Ø All leaves are of equal width except the leaf hinged to the post Guide Channel: Brass 94 Note: Situation The Hinged dimension to Post for the leaf hinged to the post (X) is, Aluminium No offset 94X to A, less B (half the leaf thickness), less 4mm. Channel butts on post Aluminium 94(X) threshold/guide channel 94T A Formula: X=(A-B)-4mm Hinges: Butt hinges - 100x7 3/3 Side to Open Even -/- 4m Even Even -/- Half Door Thickness (A) Accessories: Flushpull 0 Flushbolts SF190//600 Narrow bolt and keep F371 & F

32 FLEXIROL EXTERIOR ENDFOLD FOR TIMBER DOORS Track 0 Clearance Double Seal (Wind and Waterproof) High Sound Deduction 6A/2 with 6B Hinge (mm or mm) Nut Lock Nut 37 Inside Outside Inside Outside Cram Plate Pre Drill Hole Ø 6mm Hinge 6B 8 3 Do A W C 43-7 Lock Nut Nut Guide 67BA Hinge Sleeve Angle Profile not by PCH Double Seal (Wind and Waterproof) High Sound Deduction Not by PCH 94T* *94T=Cut Version NOT Standard or Supplied by PCH 94(X) 32

33 CAPACITY 98 1 Even X Even X X X 73 Clearance 4 Max. door weight: 1kg Track 0 Max. door height: 0mm Max. door width: 10mm Door thickness: 43mm-7mm 8 APPLICATIONS Inside 60 Top-hung Flexirol gear and fittings for heavy end folding 6A/2 with 6B Hinge (mm or mm) Nut timber doors. Leaves can be hung to the left or 37 right of Lock Nut an opening. DOOR TYPES Outside Inside Double Seal (Wind and Waterproof) High Sound Deduction Outside 6B Opening Width F371 6B 6A/2 with Double Hinge 67BA with Double Hinge Opening Width 6B 6A/2 and Single H F371 6 S H Cram Heavy commercial timber doors. Plate Pre Drill Hole Ø 6mm Channel 94(X) or 94T Hinge 6B 8 TECHNICAL INFORMATION 3 Track: Aluminium Door Width A is Door Width B or C + 1mm A B C B and C Same Width Outside Inside A B 42 A+ 1mm Out Ins Brackets: Face fix (fixed at 00mm intervals) 1A/0 s: Lock Nut Nut Guide 67BA Guides: 94T* Joining track 1 Even Even 3S/0 X X Intermediate or end hanger for timber/ aluminium doors with 2mm strapbolt, Opening Width Hinge no hinge Sleeve 6A/2 23 Intermediate guide for timber doors with 8 6B 10mm spindle, no hinge Double Seal (Wind and Waterproof) High Sound Deduction Angle Profile not by PCH End guide for timber doors with 110mm spindle, no hinge Double Seal (Wind and Waterproof) High Sound Deduction Not by PCH *94T=Cut Version NOT Standard or Supplied by PCH 94(X) Guide Channel: 37 Brass 94 Aluminium Aluminium threshold/guide channel F371 67BA/10 Inside Hinges: mm single hinge for timber doors 6B//1 Outside Pre Drill Hole Ø 6mm 6B 68BA/110 6/ / B BF A/2 with Double Hinge BA with Double Hinge 8 3 Ø 10 3 Doors Folding to the Left* 2 Doors Folding to th 17 X Opening Width X 8 6B 6A/2 and Single Hinge F B and Single Hinge Track Length = Opening Width +mm mm double hinge for timber doors Channel 94(X) or 94T 6B/ mm single hinge for timber doors Outside 6B//1 Outside mm double hinge for Door timber Width doors A B C 6B/ B and C Inside A B Inside A is Door A+ Width B or Same -mm double hinge for timber doors C + 1mm Width 6B/- 42 1mm Accessories: Flush pull 3 Doors Folding 0 to the Left* 2 Doors Folding to the Left* Flush bolts 6/ /63 333/ B BF 39- *For other options see Hinge Installation page 6. Narrow flush bolt and keep F371 & F3734 Aluminium door mounting kit 60B X 94T 6B B Ø Ø Angle Profile not by PCH * All with stainless steel strapbolt/spindle. Hinge Sleeve Refer to page 60 for hinge installation. 8 Double Seal (Wind and Waterproof) High Sound Deduction Not by PCH Ø B B Ø Ø T Standard or Supplied by PCH 94(X) Hinges for hangers and guides must be ordered separately. Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides. 33

34 FLEXIROL EXTERIOR ENDFOLD FOR ALUMINIUM DOORS 98 Track 0 73 Outside Track 0 Strap Bolt Stainless Steel 4 Inside 100 6A/2 4 6B Double Hinge (mm or mm) Plan: 3 Doors Folding to the Left Nut M12 Lock Nut M12 Swing Door Ø 12mm Doors not by PCH Doors not by PCH Even Even Centre to Centre Hinge Distance 6A/2 with 6B Double Hinge Track 0 27 Plastic Cover Lock Nut M12 Nut M12 6B Double Hinge (mm or mm) Roller Guide 67BA/ Threshold 94T 67BA/2 with 6B Double Hinge 94(X) or 94T 34

35 CAPACITY Maximum door weight: Maximum door height: Maximum door width: Door thickness: APPLICATIONS 1kg 0mm 10mm 43mm-7mm 12 67BA/1 67BA/ BA Top-hung Guide Flexirol gear and fittings for end folding with aluminium 6B doors. Leaves can be hung to the left Double or right of Hinge an opening DOOR TYPES Channel 94(X) or Threshold 94T Flexirol Exterior Endfold is suitable for aluminium doors. Fixing components are not supplied as standard for aluminium doors. Outside TECHNICAL INFORMATION Inside Track: Aluminium 0 4 Brackets: Face fix (fixed at 00mm intervals) 1A/0 Joining track 3S/0 4 Ø Ø 16 Doors not by PCH *s: Plan: 3 Doors Folding to the Right *Guides: Intermediate or end hanger for timber/ aluminium doors with 2mm strapbolt, no hinge 6A/2 Intermediate guide for aluminium with 10mm spindle, no hinge End guide for aluminium doors with 110mm spindle, no hinge 67BA/2 68BA/180 6B Double Hinge (mm or mm) S/7 Packer (optional) Guide Channel: Brass 94 Swing Door Aluminium Even Even Aluminium threshold/guide channel 94X 94T 10 67BA/2 Hinges: mm single hinge for timber doors 6B//1 mm double hinge for timber doors 6B/ mm single hinge for timber doors 6B//1 mm double hinge for timber doors 6B/ -mm double hinge for timber doors 6B/- 94(X) Alternative Guiding System Accessories: Flushpull 0 Narrow bolt and keep F371 & F3734 7mm packer S/7 (optional, depending on frame and track layout) * All with stainless steel strapbolt/spindle. For aluminium doors use in conjunction with a 60B mounting kit. Consult with PCH Technical Department for extrusion compatibility. Hinges for hangers and guides must be ordered separately. Use a single hinge for end hangers and guides, double hinge for intermediate hangers and guides. 3

36 36

37 FLEXIROL MULTIDIRECTIONAL DOOR SYSTEMS The Henderson series of multidirectional door systems offers the designer unparalleled flexibility without compromising on the practicality of the application. The Flexirol multidirectional system offers two degrees of movement to provide this flexibility. The Flexirol system offers a choice of two hangers providing either 90º or 13º maximum movement to a maximum weight of 00kg depending on the choice of hanger. This system offers the options of curved track and track coloured to any BS colour, as well as a variety of plated finishes. The multidirectional range is ideal for shopfronts, internal partitions, movable walls, conference rooms and any situation requiring the flexibility of a stacking system. 37

38 FLEXIROL 90º MULTIDIRECTIONAL SYSTEM FOR TIMBER AND ALUMINIUM DOORS Top Pivot /0P / / Ball Bearing House Ø Adjustable Nut Grub Screw 10-6 Drill Hole Ø 18 x 0 6 Grub Screw Drill Hole Ø 18 x 0 Adjustable Nut Drill Hole Ø M18 x 0 Grub Screw / Drill Hole Ø M18 x 0 Bottom Pivot Narrow Bolt F Cover x 4 x 3 3 Pivot Socket Ø Bottom Pivot /0P 28 Keep F3734

39 R R3.10 R3.10 l Bearing ouse Ø 0 Adjustable Nut Bearing ouse Adjustable Nut Cover x 4 x Top Pivot Bottom /0P Pivot /0P 6 CAPACITY Maximum door weight: 100kg (2 hangers per leaf) 17. 0kg (1 hanger per leaf) Maximum door height: 6000mm Bottom Pivot Narrow Bolt F371 2 Maximum door width: 6000mm Door thickness: mm-100mm Maximum swing door width: 10mm Pivot Socket Ø APPLICATIONS Top Pivot /0P Grub Screw Bottom Pivot / /61 Lightweight partitions for internal and external Grub Screw 10- Grub Screw Adjustable applications 6requiring Nut 10- / /61 90º movement. 6 6Drill Hole Ø 18 x 0 DOOR TYPES Drill Hole Commercial timber and aluminium doors. Ø M18 x 0 TECHNICAL INFORMATION Track: Grub Screw 10-6Drill Hole Ø 18 x 0 Drill Hole Ø 18 x 0 Bottom Pivot Keep F (extruded aluminium) Intersects: T junction TW/0 Cross-junction KW/0 Elbows: 90 elbow H90/0 Brackets: Face fix 1A/0 Soffit fix 3S/0 Narrow Bolt F Grub Screw Drill Hole Ø 18 x 0 2 Adjustable Nut Drill Hole Ø M18 x 0 Narrow s: Bolt Angle plate fixing / 2 Concealed fixing /61 Grub Screw Swing Door Sliding Door 90º Configurations System A Swing Direction Jointing Strip 1/180 Jointing 90 Strip Elbow System B H90/0 1/ Elbow H90/0 90 Door Rebates 1H/90 Jointing Strip /61 1H/90 Jointing Strip Example Rebated Doors Swing Door Sliding Door Swing Door Sliding Door System A System A /61 Door Needs Radius / Swing Direction System C System D Swing Door System E System C System D Pivot /0P Clearance Jointing Strip 1/180 2H/90 Track/ Guide / 2H/90 Track/ Guide / Door Needs Radius Swing Direction Door Needs Radius / / System C 18 Jointing Strip 90 1/180 T-Junction TW/0 90 Jointing 90 T-JunctionStrip TW/0 1H/90 90 Jointing Strip 1H/90 18 Swing Door Swing Door Pivot /0P Pivot /0P 4 Seal Not By PCH 2 Seal Not By PCH Clearance Clearance over x 4 x 3 ttom ivot 0P over 4 x 3 tom vot 0P Pivot Socket Ø Pivot Socket Ø Pivots: Pivot set /0P Keep F Accessories: 3 30 Track stop HH3/301 Flushpull 0 Keep F3734 Flushbolts SF190//600 System B System B System D System E System E Narrow bolt and keep F371 & F3734 Door closers Floor spring closer 7410 Transom closer 600 (complete with 0mm of 0 track) Swing/slide floor spring

40 FLEXIROL 13º MULTIDIRECTIONAL SYSTEM FOR TIMBER AND ALUMINIUM DOORS 98 6/ 6/61 73 Top Pivot /0P 10- Ball Bearing House Ø Adjustable Nut 6 Grub Screw 10- Drill Hole Ø 18 x 0 Grub Screw 6 Drill Hole Ø 18 x 0 Adjustable Nut Grub Screw Drill Hole Ø 18 x Bottom Pivot Narrow Bolt F Cover x 4 x 3 3 Pivot Socket Ø Bottom Pivot /0P 28 Keep F3734

41 CAPACITY Swing Door Sliding Door Swing Direction 13º Configurations Door Needs Radius Swing Door Pivot /0P Adjustable Nut Ball Bearing - House Adjustable 28Ø Nut ll Bearing House Ø Cover x 4 x 3 Bottom Cover Pivot x /0P 4 x 3 ottom ivot /0P Bottom Pivot Pivot Socket Ø Top Pivot /0P Top Pivot /0P 6 6 Maximum door weight: 00kg (2 hangers per leaf) Narrow Bolt 0kg (1 hanger per leaf) F371 2 Maximum door height: 6000mm Maximum door width: 6000mm 6/ 6/61 Door thickness: mm-100mm Maximum 6/ swing door width: 6/61 10mm Grub Screw 10- Grub Screw Adjustable Nut APPLICATIONS Grub Screw 6 6 Multidirectional Flexirol Drill Hole is ideally Drill suited Hole to hotels, Ø 18 x 0 Ø 18 x 0 conference 13 centres, shopfronts, 18 showrooms, Drill Hole Drill Hole Ø 18 x 0 Ø 18 x 0 and other applications that requires high performance and the flexibility of 13º movement. Drill Hole Ø 18 x 0 Drill Hole Ø 18 x DOOR TYPES Heavy commercial timber and aluminium doors. TECHNICAL INFORMATION Track: Keep F (extruded aluminium) Intersects: 13 right-hand 4R/0 13 left-hand 4L/0 Bottom Pivot Narrow Bolt F Elbows: Narrow Bolt 13 swept elbow H13/0 F swept elbow H90C/0 for 13 hanger Brackets: Face fix 1A/0 Pivot Socket Ø 23 Soffit fix 3S/0 Bottom Pivot Grub Screw 3 30 Keep F3734 Adjustable Nut Grub Screw 6 s: Angle plate fixing 6/ 3 30 Keep Concealed fixing 6/61 F3734 Pivot Socket Ø Pivots: Pivot set /0P Grub Screw / Swept Elbow H13/0 Door 1H/13Rebates Accessories: Track stop HH3/301 Flushpull 0 Flushbolts SF190//600 Narrow bolt and keep F371 & F3734 Door closers Floor spring closer 7410 Transom closer 600 System A 1/180 Intersect Right 4R/0 1/180 Intersect 13 Right 4 4R/01H/13 1H/ H/13 1H/4 (Top View) Track Guide 2H/13 (Top View) 1/ Swept Elbow H13/0 Track System 13 Guide C Elbow 2H/ Elbow System A System C 13 Intersect System B Left 4L/0 Intersect Left 13 4L/ Swept System D Elbow H90C/0 90 Swept Elbow 90 System H90C/0 E /180 1H/13 1/ / 6/ Example Rebated Doors Swing Direction 6/ 6/61 Swing Door Door Needs Radius Swing Swing Direction Door Door Needs Radius Swing Door Sliding Door Swing Door Sliding Door System A System C Stop HH3/ System E System B System B 6/ System E System D System D 4 4 1H/13 1H/13 Pivot /0P 178 Pivot /0P Clearance 2 Clearance 2 Clearance 23- Adjustable Nut 23- Adjustable Nut 41

42 HINGE INSTALLATION Standard Fixing to Post (Flush) Hinge 6B/ 3 Door Just Folding *Single Sealed Door Rubber Sealing not by PCH Cram Plate Standard Fixing to Post (Flush) Hinge 6B/ 3 *Double Sealed Door Standard Fixing to Post (Flush) Hinge 6B/ Hinge 6B Hinge 6B/ Hinge 6B/- 1 Distance from the edge of the door leaf to the centre of the hinge Hinge 6B/ COMPONENTS HINGES 6B/ 6B/- 6B/

43 TRACK, INTERSECTS AND CURVES 600 CFP 600 FP 600 CFP 600 FP Husky Pacer Flexirol 0 Track A 600 Track Pacer Switch 4R/600 Switch 4L/ Track TrackPacer Curve Pacer 600 Curve Track C 600 C 280 A 280 A O O 4 O Pacer O O 4 (Bottom View) (Bottom View) R 374 R 37 ( PACER CURVES/INTERSECTS Jointing Bracket 1BX (Bottom Views) Bracket 1B 0 Track 0 Track 600 Track 600 Track Pacer Switch Pacer 4R/600 Switch 4R/600 Pacer Switch Bracket Pacer 4L/600 Switch 1B 4L/ Pacer Curve C Ø O Ø 9 34 Ø O 4 O 4 4 O 4 O R/0 1/ L/0 48 Intersect Intersect R 374 Right (Bottom View) (Bottom View) 13 (Bottom Left View) (Bottom 13 View) 4 1H/13 4 1H/4 1A/0 3S/0 FLEXIROL 6 JUNCTIONS/INTERSECTSJointing Jointing Bracket Bracket 1BX 1BX 1A/0 1 (Top View) Track Guide 2H/13 (Top View) (Top Views) Bracket Bracket 1B 1B H13/0 80 H90C/0 13 Swept 90 Swept Pacer Switch 4L/ Elbow 13 Elbow Ø Ø R/0 1/180 1/180 4L/0 4L/0 Bolt Not 1/ Elbow Supplied Intersect Intersect Intersect Intersect Bolt 90 Not Right Right 9 Ø by PCH Supplied Left LeftØ by PCH H/ H/4 1H/4 4 O CFP FP 1H/13 1/ (Top (Top View) View) Track Guide 2H/13 24(Top (Top View) View) 1H/13 Track Guide 2H/13 (Bottom View) Bolt Not H13/0 H90C/0 Pacer Curve 600 C Supplied Bolt Not Swept 280 SweptA Swept Swept by PCH Supplied Elbow Elbow FLEXIROL Elbow Elbow JUNCTIONS/INTERSECTS by PCH 33 1A/0 1A/0 3S/0 3S/0 4 O 1/180 1/ Elbow Elbow Face Fix Bracket 281AN Jointing Bracket 281AX 1 et 1BX H90/0 H90/ TW/0 TW/ Jointing Face Fix Bracket 281AN Jointing Strip 70 Strip 3 8. Strip Strip / /180 Ø.0 1 Ø Ø 9 Ø H/13 1H/13 Bolt Not Bolt Not R 374 1/180 Supplied 1/ Elbow Elbow T-Junction Supplied 34 by 100- by PCH 100- by PCH 1H/13 1H/ Jointing Strip 24.9 Strip H/ Throughout 14.0 Throughout 0 Track Bolt Not 30 Bolt Not 1H/90 Strip Guide Track Supplied Jointing Strip 2H/90 Track/ Guide SuppliedPacer Switch 4R/600 Pacer Switch 4L/600 by by PCH by PCH 98 Pacer track supplied in mill 48 finish as standard. Flexirol track 30 supplied in mill finish and RAL as standard. Face Fix Face Bracket Fix Bracket 281AN 281AN Jointing Jointing Bracket Bracket 281AX 281AX BRACKETS Pacer Bracket 1B Bracket 1B Ø.0 Ø O 4 O Ø.0 Ø (Bottom View) (Bottom View) Pacer 24.9 Jointing Bracket 1BX Jointing 30 Bracket 1BX 70 Bracket 281AX 34 Ø Ø 9 13 Ø A/ S/0 43 1