V graph Y. The three circuit elements are a metal wire at constant temperature, a semiconductor diode and a filament lamp.

Similar documents
7. What is the current in a circuit if 15 coulombs of electric charge move past a given point in 3 seconds? (1) 5 A (3) 18 A (2) 12 A (4) 45 A

Chapter 13: Electric Circuits

Series and Parallel Circuits

AP1 Electricity. 1. A student wearing shoes stands on a tile floor. The students shoes do not fall into the tile floor due to

Circuit symbol. Each of the cells has a potential difference of 1.5 volts. Figure 1. Use the correct answer from the box to complete the sentence.

1. The diagram below represents magnetic lines of force within a region of space.

Review Questions PHYS 2426 Exam 2

Objectives 200 CHAPTER 4 RESISTANCE

PHYSICS 111 LABORATORY Experiment #3 Current, Voltage and Resistance in Series and Parallel Circuits

People s Physics Book

AP Physics Electricity and Magnetism #4 Electrical Circuits, Kirchoff s Rules

Electrical Fundamentals Module 3: Parallel Circuits

Σ I in = Σ I out E = IR 1 + IR 2 FXA 2008 KIRCHHOFF S LAWS 1. Candidates should be able to : LAW 1 (K1)

Ohm's Law and Circuits

V out = V in x R 2 (R 1 + R 2 ) V o = V i R 1 FXA 2008 POTENTIAL DIVIDER CIRCUIT 1. Candidates should be able to : SUPPLYING A FIXED PD

Resistors in Series and Parallel

MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

Wires & Connections Component Circuit Symbol Function of Component. Power Supplies Component Circuit Symbol Function of Component

Physics. Cambridge IGCSE. Workbook. David Sang. Second edition Cambers & Sibley: IGCSE Physics Cover. C M Y K

Chapter 7 Direct-Current Circuits

Force on Moving Charges in a Magnetic Field

Lab 3 - DC Circuits and Ohm s Law

Series and Parallel Circuits

Series and Parallel Circuits

Candidate Number. General Certificate of Education Advanced Level Examination June 2010

PS-6.2 Explain the factors that determine potential and kinetic energy and the transformation of one to the other.

STUDY MATERIAL FOR CLASS Physics- CURRENT ELECTRICITY. The flow of electric charges in a particular direction constitutes electric current.

CURRENT ELECTRICITY - I

GRADE 11A: Physics 5. UNIT 11AP.5 6 hours. Electronic devices. Resources. About this unit. Previous learning. Expectations

Current, Resistance and Electromotive Force. Young and Freedman Chapter 25

Physics, Chapter 27: Direct-Current Circuits

13.10: How Series and Parallel Circuits Differ pg. 571

Solutions to Bulb questions

Chapter 22 Further Electronics

ELECTRICAL CIRCUITS. Electrical Circuits

Experiment #3, Ohm s Law

Eðlisfræði 2, vor 2007

AS COMPETITION PAPER 2007 SOLUTIONS

Aircraft Electrical System

ELECTRIC FIELD LINES AND EQUIPOTENTIAL SURFACES

CHAPTER 28 ELECTRIC CIRCUITS

Exercises on Voltage, Capacitance and Circuits. A d = ( ) π(0.05)2 = F

DIRECT CURRENT GENERATORS

Objectives. Electric Current

Physics 121 Sample Common Exam 3 NOTE: ANSWERS ARE ON PAGE 6. Instructions: 1. In the formula F = qvxb:

Modified True/False Indicate whether the statement is true or false. If false, change the identified word or phrase to make the statement true.

General Physics (PHY 2140)

Candidate Number. General Certificate of Education Advanced Level Examination June 2012

Chapter 19. Electric Circuits

A-level PHYSICS (7408/1)

Student Exploration: Circuits

The purposes of this experiment are to test Faraday's Law qualitatively and to test Lenz's Law.

Experiment #5, Series and Parallel Circuits, Kirchhoff s Laws

VCE Physics and VCE Systems Engineering: Table of electronic symbols

Chapter 5. Parallel Circuits ISU EE. C.Y. Lee

Circuits. The light bulbs in the circuits below are identical. Which configuration produces more light? (a) circuit I (b) circuit II (c) both the same

Lecture Notes: ECS 203 Basic Electrical Engineering Semester 1/2010. Dr.Prapun Suksompong 1 June 16, 2010

Complete tests for CO 2 and H 2 Link observations of acid reactions to species

TEACHER S CLUB EXAMS GRADE 11. PHYSICAL SCIENCES: PHYSICS Paper 1

Fig. 1 Analogue Multimeter Fig.2 Digital Multimeter

Chapter 7. DC Circuits


Resistors in Series and Parallel

AS COMPETITION PAPER 2008

3.- What atom s particle moves through a conductor material? 4.- Which are the electric components of an elemental electric circuit?

EXPERIMENT 7 OHM S LAW, RESISTORS IN SERIES AND PARALLEL

PHYSICS PAPER 1 (THEORY)

Digital Energy ITI. Instrument Transformer Basic Technical Information and Application

Energy, Work, and Power

Candidate Number. General Certificate of Education Advanced Level Examination June 2014

Voltage Drop (Single-Phase)

Junior Cert Science Numeracy Resources

Objectives. Capacitors 262 CHAPTER 5 ENERGY

Resistors in Series and Parallel Circuits

Solution Derivations for Capa #11

BSNL TTA Question Paper-Instruments and Measurement Specialization 2007

Episode 126: Capacitance and the equation C =Q/V

ELECTRICAL FUNDAMENTALS

45. The peak value of an alternating current in a 1500-W device is 5.4 A. What is the rms voltage across?

Time allowed: 1 hour 45 minutes

Physics 133: tutorial week 4 Ohm s law, electrical power, emf and internal resistance.

E/M Experiment: Electrons in a Magnetic Field.

Lab 2: Resistance, Current, and Voltage

HOW TO USE MULTIMETER. COMPILE BY: Dzulautotech

Basic Principles of. Electricity. Basic Principles of Electricity. by Prof. Dr. Osman SEVAİOĞLU Electrical and Electronics Engineering Department

Method 1: 30x Method 2: 15

Tutorial 12 Solutions

G482 Electrons, Waves and Photons; Revision Notes Module 1: Electric Current

Series and Parallel Resistive Circuits Physics Lab VIII

CLASS TEST GRADE 11. PHYSICAL SCIENCES: PHYSICS Test 3: Electricity and magnetism

Modern Physics Laboratory e/m with Teltron Deflection Tube

Lab E1: Introduction to Circuits

Forms of Energy. Freshman Seminar

Measurement of Capacitance

Introduction to Electricity & Magnetism. Dr Lisa Jardine-Wright Cavendish Laboratory

Light Bulbs in Parallel Circuits

Course description: Introduces the student to basic electricity with an emphasis on Ohms Law.

The Electrical Properties of Materials: Resistivity

Magnetic Fields and Their Effects

PHYS 222 Spring 2012 Final Exam. Closed books, notes, etc. No electronic device except a calculator.

Transcription:

1 1 The graphs show the variation with potential difference of the current for three circuit elements. graph X graph Y graph Z The three circuit elements are a metal wire at constant temperature, a semiconductor diode and a filament lamp. Which row of the table correctly identifies these graphs? metal wire semiconductor filament at constant temperature diode lamp X Z Y Y X Z Y Z X Z X Y 2 The filament of a 24, 1 W electric lamp heats up from room temperature to its operating temperature. s it heats up, its resistance increases by a factor of 16. What is the resistance of this lamp at room temperature? 36 Ω 58 Ω 1.5 kω 9.2 kω 3 The diagrams show connected wires which carry currents 1, 2, 3 and 4. The currents are related by the equation 1 + 2 = 3 + 4. To which diagram does this equation apply? 1 3 4 2 3 1 1 4 2 3 1 4 2 2 3 4

2 4 n the circuit below, the battery converts an amount E of chemical energy to electrical energy when charge passes through the resistor in time t. Which expressions give the e.m.f. of the battery and the current in the resistor? e.m.f. current E /t E t E/ /t E/ t 5 potential divider is used to give outputs of 2 and 3 from a 5 source, as shown. +5 R 1 +3 R 2 +2 R 3 What are possible values for the resistances R 1, R 2 and R 3? R 1 / k Ω R 2 / k Ω R 3 / k Ω 2 1 5 3 2 2 4 2 4 4 6 1

3 6 When four identical lamps P,, R and S are connected as shown in diagram 1, they have normal brightness. P P R S diagram 1 R S diagram 2 When the four lamps are connected as shown in diagram 2, which statement is correct? The lamps do not light. The lamps are less bright than normal. The lamps have normal brightness. The lamps are brighter than normal. 7 What physical quantity would result from a calculation in which a potential difference is multiplied by an electric charge? electric current electric energy electric field strength electric power 8 The current in a component is reduced uniformly from 1 m to 2 m over a period of 8. s. What is the charge that flows during this time? 16 m 32 m 48 m 64 m 9 The sum of the electrical currents into a point in a circuit is equal to the sum of the currents out of the point. Which of the following is correct? This is Kirchhoff s first law, which results from the conservation of charge. This is Kirchhoff s first law, which results from the conservation of energy. This is Kirchhoff s second law, which results from the conservation of charge. This is Kirchhoff s second law, which results from the conservation of energy.

4 1 The diagram shows a potential divider connected to a 9. supply of negligible internal resistance. 1 kω 9. P 5 kω What range of voltages can be obtained between P and? zero to 1.5 zero to 7.5 1.5 to 7.5 1.5 to 9. 11 The e.m.f. of the cell in the following circuit is 9.. The reading on the high-resistance voltmeter is 7.5. 15 Ω What is the current?.1.5.6 2. 12 The diagram shows an arrangement of four resistors. 1 kω 6kΩ X 6kΩ 1 kω What is the resistance between X and Y? 4kΩ 8kΩ 16 kω 32 kω Y

5 13 The terminal voltage of a battery is observed to fall when the battery supplies a current to an external resistor. What quantities are needed to calculate the fall in voltage? the battery's e.m.f. and its internal resistance the battery's e.m.f. and the current the current and the battery's internal resistance the current and the external resistance 14 The diagram shows a battery, a fixed resistor, an ammeter and a variable resistor connected in series. voltmeter is connected across the fixed resistor. The value of the variable resistor is reduced. Which correctly describes the changes in the readings of the ammeter and of the voltmeter? ammeter voltmeter decrease decrease decrease increase increase decrease increase increase 15 copper wire of cross-sectional area 2. mm 2 carries a current of 1. How many electrons pass through a given cross-section of the wire in one second? 1. x 1 1 5. x 1 6 6.3 x 1 19 3.1 x 1 25 16 cylindrical piece of a soft, electrically-conducting material has resistance R. t is rolled out so that its length is doubled but its volume stays constant. What is its new resistance? R R 2 R 4 R 2

6 17 Kirchhoff s two laws for electric circuits can be derived by using conservation laws. On which conservation laws do Kirchhoff s laws depend? Kirchhoff s first law Kirchhoff s second law charge current charge energy current mass energy current 18 The diagram shows a parallel combination of three resistors. The total resistance of the combination is 3 Ω. 12 Ω 6 Ω What is the resistance of resistor X? 2Ω 3Ω 6Ω 12 Ω X 19 Which electrical component is represented by the following symbol? a diode a light-dependent resistor a resistor a thermistor 2 Which equation is used to define resistance? energy = (current) 2 resistance time potential difference = current resistance power = (current) 2 resistance resistivity = resistance area length

7 21 Which diagram represents the electric field in the vicinity of a positive electric charge of magnitude? 22 The - characteristics of two electrical components P and are shown below. / 2. 1.5 1. P.5 2. 4. 6. 8. / Which statement is correct? P is a resistor and is a filament lamp. The resistance of increases as the current in it increases. t 1.9 the resistance of is approximately half that of P. t.5 the power dissipated in is double that in P.

8 23 The diagram shows a circuit with four voltmeter readings, 1, 2 and 3. 1 R R 2 2R Which equation relating the voltmeter readings must be true? = 1 + 2 + 3 + 1 = 2 + 3 3 = 2( 2 ) 1 = 3 3 24 The diagram shows an arrangement of resistors. X 1 Ω 1 Ω 1 Ω Y 1 Ω What is the total electrical resistance between X and Y? less than 1 Ω between 1 Ω and 1 Ω between 1 Ω and 3 Ω 4 Ω

9 25 n the circuit below, P is a potentiometer of total resistance 1 Ω and is a fixed resistor of resistance 1 Ω. The battery has an e.m.f. of 4. and negligible internal resistance. The voltmeter has a very high resistance. The slider on the potentiometer is moved from X to Y and a graph of voltmeter reading is plotted against slider position. P X 4. Y Which graph is obtained? 4 4 2 2 X slider position Y X slider position Y 4 4 2 2 X slider position Y X slider position 26 total charge of 1 flows through a 12 W light bulb in a time of 5 s. What is the potential difference across the bulb during this time?.12 2. 6. 24 Y

1 27 The current in the circuit is 4.8. R X Y What is the rate of flow and the direction of flow of electrons through the resistor R? 3. 1 19 s 1 in direction X to Y 6. 1 18 s 1 in direction X to Y 3. 1 19 s 1 in direction Y to X 6. 1 18 s 1 in direction Y to X 28 p.d. of 12 is connected between P and. 5 Ω X 1 Ω P 2 Ω Y 1 Ω What is the p.d. between X and Y? 4 6 8 29 The potential difference between point X and point Y is 2. The time taken for charge carriers to move from X to Y is 15 s, and, in this time, the energy of the charge carriers changes by 12 J. What is the current between X and Y?.4.11 9. 25 3 power cable X has a resistance R and carries current. second cable Y has a resistance 2R and carries current 2 1. What is the ratio 1 4 power dissipated in Y? power dissipated in X 1 2 2 4

11 31 The diagram shows a low-voltage circuit for heating the water in a fish tank. source heater The heater has a resistance of 3. Ω. The voltage source has an e.m.f. of 12 and an internal resistance of 1. Ω. t what rate does the voltage source supply energy to the heater? 27 W 36 W 48 W 64 W 32 Two wires made of the same material and of the same length are connected in parallel to the same voltage supply. Wire P has a diameter of 2 mm. Wire has a diameter of 1 mm. What is the ratio current in P current in? 4 1 2 1 2 4 33 What is a correct statement of Ohm s law? The potential difference across a component equals the current providing the resistance and other physical conditions stay constant. The potential difference across a component equals the current multiplied by the resistance. The potential difference across a component is proportional to its resistance. The potential difference across a component is proportional to the current in it providing physical conditions stay constant. 34 potential difference is applied between two parallel plates a small distance d apart, and produces an electric field of strength E between the plates. d What is the electric field strength between the plates when both and d are doubled? E /4 E 2E 4E

35 When four identical lamps P,, R and S are connected as shown in diagram 1, they have normal brightness. 12 P P R S R S diagram 1 diagram 2 The four lamps and the battery are then connected as shown in diagram 2. Which statement is correct? The lamps do not light. The lamps are less bright than normal. The lamps have normal brightness. The lamps are brighter than normal. 36 The diagram shows a light-dependent resistor (LR) and a thermistor forming a potential divider. + Under which set of conditions will the potential difference across the thermistor have the greatest value? illumination temperature low low high low low high high high

13 37 The current in a resistor is 8. m. What charge flows through the resistor in.2 s?.16 m 1.6 m 4. m.4 38 cell of e.m.f. 2. and negligible internal resistance is connected to the network of resistors shown. 5. kω 2. kω 2. P 5. kω 3. kω S 1 is the potential difference between S and P. 2 is the potential difference between S and. What is the value of 1 2? +.5 +.2.2.5 39 circuit is set up with an LR and a fixed resistor as shown. 5 k Ω 9 The voltmeter reads 4. The light intensity is increased. What is a possible voltmeter reading? 3 4 6 8

4 n the circuit below, the battery converts an amount E of chemical energy to electrical energy when charge passes through the resistor in time t. 14 Which expressions give the e.m.f. of the battery and the current in the resistor? e.m.f. current E / t E t E / / t E / t 41 battery has an e.m.f. of 3. and an internal resistance of 2. Ω. 3. 2. Ω battery The battery is connected to a load of 4. Ω. 4. Ω What are the terminal potential difference and output power P? / P / W 1..5 1. 1.5 2. 1. 2. 1.5

42 researcher has two pieces of copper of the same volume. ll of the first piece is made into a cylindrical resistor P of length x. x 15 resistor P current ll of the second piece is made into uniform wires each of the same length x which he connects between two bars of negligible resistance to form a resistor. x resistor current wires bar of negligible resistance How do the electrical resistances of P and compare? P has a larger resistance than. has a larger resistance than P. P and have equal resistance. may have a larger or smaller resistance than P, depending on the number of wires made. 43 Which equation is used to define resistance? power = (current) 2 resistance resistivity = resistance area length potential difference = current resistance energy = (current) 2 resistance time 44 Two copper wires X and Y have the same volume. Wire Y is four times as long as wire X. L 4 L X Y resistance of wire Y What is the ratio? resistance of wire X 4 8 16 64

45 n the circuit shown, the 6. battery has negligible internal resistance. Resistors R 1 and R 2 and the voltmeter have resistance 1 kω. 6. 16 R 1 R 2 1 kω 1 kω 1 kω What is the current in the resistor R 2? 2 µ 3 µ 4 µ 6 µ 46 The unknown e.m.f. E of a cell is to be determined using a potentiometer circuit. The balance length is to be measured when the galvanometer records a null reading. What is the correct circuit to use? E E E E

17 47 The graph shows how the current through a lamp filament varies with the potential difference across it. current p.d. Which statement explains the shape of this graph? s the filament temperature rises, electrons can pass more easily through the filament. t takes time for the filament to reach its working temperature. The power output of the filament is proportional to the square of the current through it. The resistance of the filament increases with a rise in temperature. 48 t a circuit junction, a current divides into currents 1, 2 and 3. 1 2 3 These currents are related by the equation = 1 + 2 + 3. Which law does this statement illustrate and on what principle is the law based? Kirchhoff s first law based on conservation of charge Kirchhoff s first law based on conservation of energy Kirchhoff s second law based on conservation of charge Kirchhoff s second law based on conservation of energy

49 The variation with potential difference of the current in a semiconductor diode is shown below. 18 / m 5-2. -1. 1. 2. / -5 What is the resistance of the diode for applied potential differences of +1. and 1.? resistance at +1. at 1. 2 Ω infinite 2 Ω zero.5 Ω infinite.5 Ω zero 5 The combined resistance R T of two resistors of resistances R 1 and R 2 connected in parallel is given by the formula 1 1 1 = + R T R 1 R 2 Which statement is used in the derivation of this formula? The currents through the two resistors are equal. The potential difference across each resistor is the same. The supply current is split between the two resistors in the same ratio as the ratio of their resistances. The total power dissipated is the sum of the powers dissipated in the two resistors separately.

51 n the potentiometer circuit below, the moveable contact is placed at N on the bare wire XY, such that the galvanometer shows zero deflection. 19 X N Y The resistance of the variable resistor is now increased. What is the effect of this increase on the potential difference across the wire XY and on the position of the moveable contact for zero deflection? potential difference across XY position of moveable contact increases nearer to X increases nearer to Y decreases nearer to X decreases nearer to Y 52 Six resistors, each of resistance 5 Ω, are connected to a 2 cell of negligible internal resistance. 2 5 Ω 5 Ω X 5 Ω 5 Ω 5 Ω 5 Ω What is the potential difference between terminals X and Y? 2 Y

2 53 Which electrical quantity would be the result of a calculation in which energy is divided by charge? current potential difference power resistance 54 wire carries a current of 2. amperes for 1. hour. How many electrons pass a point in the wire in this time? 1.2 1 15 7.2 1 3 1.3 1 19 4.5 1 22 55 The diagram shows a circuit in which the battery has negligible internal resistance. 12 6. Ω 3. Ω 2. Ω What is the value of the current? 1. 1.6 2. 3. 56 Which diagram shows a potential divider circuit that can vary the voltage across the lamp?

21 57 The diagram shows currents 1, 2, 3, 4 and 5 in different branches of a circuit. 1 2 3 Which one of the following is correct? 4 5 1 = 2 + 3 2 = 1 + 3 3 = 4 + 5 4 = 5 + 3 58 The diagram shows four heaters and the current in each. Which heater has the greatest power dissipation? 8 2 Ω 6 4 Ω 4 6 Ω 2 59 When a potential difference is applied between the ends of a wire of diameter d and length l, the current in the wire is. 8 Ω What is the current when a potential difference of 2 is applied between the ends of a wire of the same material of diameter 2d and the length 2l? ssume that the temperature of the wire remains constant. 2 4 8

22 6 The diagram shows two circuits. n these circuits, only the internal resistances differ. 1.5.5 Ω 1.5 2. Ω 3. Ω circuit X 3. Ω circuit Y Which line in the table is correct? potential difference across 3. Ω resistor power dissipated in 3. Ω resistor greater in X than in Y less in X than in Y greater in X than in Y greater in X than in Y less in X than in Y less in X than in Y less in X than in Y greater in X than in Y 61 n a uniform electric field, which statement is correct? ll charged particles experience the same force. ll charged particles move with the same velocity. ll electric field lines are directed towards positive charges. ll electric field lines are parallel. 62 Which of the following describes the electric potential difference between two points in a wire that carries a current? the force required to move a unit positive charge between the points the ratio of the energy dissipated between the points to the current the ratio of the power dissipated between the points to the current the ratio of the power dissipated between the points to the charge moved 63 Two heating coils X and Y, of resistance R X and R Y respectively, deliver the same power when 12 is applied across X and 6 is applied across Y. What is the ratio R X / R Y? ¼ ½ 2 4

23 64 The resistance of a thermistor decreases significantly as its temperature increases. The thermistor is kept in air. The air is at room temperature. Which graph best represents the way in which the current in the thermistor depends upon the potential difference across it? 65 The diagram shows a junction in a circuit where three wires P, and R meet. The currents in P and are 1 and 3 respectively, in the directions shown. 3 P 1 R How many coulombs of charge pass a given point in wire R in 5 seconds?.4.8 2 1 66 The diagram shows a potentiometer and a fixed resistor connected across a 12 battery of negligible internal resistance. 12 2 Ω 2 Ω output The fixed resistor and the potentiometer each have resistance 2 Ω. The circuit is designed to provide a variable output voltage. What is the range of output voltages? 6 12 6 12 12 2

24 67 The diagram shows a potential divider circuit designed to provide a variable output p.d. 5. kω 9. 5. kω output Which gives the available range of output p.d? maximum output minimum output 3. 4.5 9. 9. 4.5 68 n the circuit shown, the ammeters have negligible resistance and the voltmeters have infinite resistance. 1 3 Ω 2 2 Ω 6 Ω 2 Ω 1 2 The readings on the meters are 1, 2, 1 and 2, as labelled on the diagram. Which is correct? 1 > 2 and 1 > 2 1 > 2 and 1 < 2 1 < 2 and 1 > 2 1 < 2 and 1 < 2

25 69 The graphs show the variation with potential difference of the current for three circuit components. graph X graph Y graph Z The components are a metal wire at constant temperature, a semiconductor diode and a filament lamp. Which row of the table correctly identifies these graphs? metal wire at constant temperature semiconductor diode filament lamp X Z Y Y X Z Y Z X Z X Y 7 The resistance of a device is designed to change with temperature. What is the device? a light-dependent resistor a potential divider a semiconductor diode a thermistor

26 71 Four point charges, each of charge, are placed on the edge of an insulating disc of radius r. The frequency of rotation of the disc is f. r What is the equivalent electric current at the edge of the disc? 4f 4 f 8πrf 2f πr 72 Which graph shows the characteristic of a filament lamp? 73 The diagram shows a circuit containing three resistors in parallel. 12 1 Ω 1 Ω X The battery has e.m.f. 12 and negligible internal resistance. The ammeter reading is 3.2. What is the resistance of X? 2.1 Ω 4.6 Ω 6. Ω 15 Ω

27 74 n electrical component has a potential difference across it and a current through it. graph of against is drawn and is marked in three sections WX, XY and YZ. Y Z X W n which ways does the resistance of the component vary within each of the three sections? WX XY YZ constant decreases increases constant increases increases increases decreases constant increases increases decreases 75 Which circuit has a resistance of 4 Ω between the terminals? 1 Ω 1 Ω 1 Ω 1 Ω 1 Ω 1 Ω 1 Ω 1 Ω 1 Ω 2 Ω 2 Ω 2 Ω 2 Ω 2 Ω 2 Ω 2 Ω 2 Ω

28 76 The diagram represents a circuit. 2 2.2 m 1 1.6 m 1.8 m Some currents have been shown on the diagram. What are the currents 1 and 2? 1 2.2 m 1.8 m.2 m 3.8 m.2 m 2. m.2 m 3.8 m 77 n electric power cable consists of six copper wires c surrounding a steel core s. c c c s c c c 1. km of one of the copper wires has a resistance of 1 Ω and 1. km of the steel core has a resistance of 1 Ω. What is the approximate resistance of a 1. km length of the power cable?.61 Ω 1.6 Ω 16 Ω 61 Ω

29 78 n electron is situated in a uniform electric field as shown in the diagram. electron field What is the direction of the electric force acting on the electron? downwards into the paper upwards out of the paper to the left to the right 79 Which diagram shows the electric field between a positively charged metal sphere and an earthed metal plate? + + + + 8 Which electrical quantity would be the result of a calculation in which energy transfer is divided by charge? current potential difference power resistance 89 Which graph best represents the way the current through a filament lamp varies with the potential difference across it?

3 9 battery of negligible internal resistance is connected to two 1 Ω resistors in series. 6. 1 Ω 1 Ω What charge flows through each of the 1 Ω resistors in 1 minute?.3.6 3. 18 91 potential divider consists of a fixed resistor R and a light-dependent resistor (LR). R What happens to the voltmeter reading, and why does it happen, when the intensity of light on the LR increases? The voltmeter reading decreases because the LR resistance decreases. The voltmeter reading decreases because the LR resistance increases. The voltmeter reading increases because the LR resistance decreases. The voltmeter reading increases because the LR resistance increases. 92 Two wires P and have resistances R P and R respectively. Wire P is twice as long as wire and has twice the diameter of wire. The wires are made of the same material. What is the ratio R P? R.5 1 2 4

31 93 The circuit is designed to trigger an alarm system when the input voltage exceeds some preset value. t does this by comparing out with a fixed reference voltage, which is set at 4.8. 15 k Ω in 1 k Ω out out is equal to 4.8. What is the input voltage in? 4.8 7.2 9.6 12 94 potentiometer is used as shown to compare the e.m.f.s of two cells. driver cell metre rule.7 m.9 m X Y The balance points for cells X and Y are.7 m and.9 m respectively. f the e.m.f. of cell X is 1.1, what is the e.m.f. of cell Y?.69.86.99 1.4 95 Two wires P and made of the same material and of the same length are connected in parallel to the same voltage supply. Wire P has diameter 2 mm and wire has diameter 1 mm. What is the ratio 1 4 current in P? current in 1 2 2 1 4 1

32 96 When four identical resistors are connected as shown in diagram 1, the ammeter reads 1. and the voltmeter reads zero. diagram 1 diagram 2 6. 6. The resistors and meters are reconnected to the supply as shown in diagram 2. What are the meter readings in diagram 2? voltmeter reading / ammeter reading / 1. 3..5 3. 1. 6. 97 The charge that a fully-charged 12 car battery can supply is 1 k. The starter motor of the car requires a current of 2 for an average period of 2. s. The battery does not recharge because of a fault. What is the maximum number of times the starter motor of the car can be used? 21 25 42 25 98 particle has a charge of 4.8 1 19. The particle remains at rest between a pair of horizontal, parallel plates having a separation of 15 mm. The potential difference between the plates is 66. What is the weight of the particle? 2.1 1 14 N 2.1 1 15 N 2.1 1 17 N 1.1 1 23 N

99 The graph shows how the electric current through a conducting liquid varies with the potential difference across it. t which point on the graph does the liquid have the smallest resistance? 33 1 n electrical component has the following circuit symbol. What does this symbol represent? variable resistor (rheostat) fuse light-dependent resistor thermistor 11 Three resistors are connected in series with a battery as shown in the diagram. The battery has negligible internal resistance. 12 Ω 6. 18 Ω 15 Ω What is the potential difference across the 18 Ω resistor? 1.6 2.4 3.6 6.

12 n the circuit below, the reading T on the voltmeter changes from high to low as the temperature of the thermistor changes. The reading L on the voltmeter changes from high to low as the level of light on the light-dependent resistor (LR) changes. 34 T L The readings on T and L are both high. What are the conditions of temperature and light level? temperature light level low low low high high low high high 13 The e.m.f. of the battery is 9.. The reading on the high-resistance voltmeter is 7.5. 9. 15 Ω What is the current?.1.5.6 2.

35 14 The potential difference across a resistor is 12. The current in the resistor is 2.. 4. passes through the resistor. What is the energy transferred and the time taken? energy / J time / s 3. 2. 3. 8. 48 2. 48 8. 15 thermistor and another component are connected to a constant voltage supply. voltmeter is connected across one of the components. The temperature of the thermistor is then reduced but no other changes are made. n which circuit will the voltmeter reading increase?