Controller board and power supply for vivimat III systems Ref: VIVIMAT-3.0 The controller board and power supply vivimat 3.0, is the central core of the vivimat III home automation system. The vivimat III systems, have high expansion capabilities, thanks to the optional modules that can be mounted on the vivimat 3.0 controller board and power supply, and also thanks to the variety of modules that can be connected to the vivimat III control BUS. The vivimat III systems, have high expansion capabilities, thanks to the optional modules that can be mounted on the vivimat 3.0 controller board and power supply, and also thanks to the variety of modules that can be connected to the vivimat III control BUS Technical characteristics External power supply 220VAC/50 o 60Hz Internal power supply 15VDC Internal consumption <100mA Power supply output for components of the vivimat III system 12-14VDC (1,25A con ALM- 0021) *See note. vivimat III systems power supply Temperature range 0-50ºC Battery (optional) hosted by vivimat 3.0 BAT-0190 /1,9Ah Expansion BUS 2 RS - 485 Interfaces BUS / control BUS Communication protocol vivimat III protocol optional Max. modules number per BUS 64* * Depending of the installation BUS load a RS485 repeater might be needed for less than 64 devices. (Include one in the system in case the communication fails)
HARDWARE CAPACITIES: Digital inputs ** 8 Analog inputs (0-10V ) 1 Current input 1 Digital relay outputs (5A @ 230Vac) 4 Transistorized digital outputs 4 Expansion connectors on board 3 Expansion Bus 1 Integrated serial port communication 2 (+3 opt.) Connection to the PSTN (switched tel. network) Integrated GSM connection Optional (MOD-0001 + MOD-0350 Firmware updates via... micro SD Allows remote reprogramming Coming soon SOFTWARE CAPACITY: Alarm zones / Areas 40/20 Climate control zones 10 Scenes 20 Events per scenes 20 Devices/plugs 20 Irrigation areas 50 Individually controlled motorized devices 50 Lighting zones (ON/OFF+Dimmer) 50 Dimming light control Max. number of screens per system 3 MODULES CONNECTED TO THE CONTROLLER BOARDS: Video doorphone system module MOD-0200 (1) Wired IP module MOD-0360 (1) Audio expansion module MOD-0800 (1) Expansion plate MOD-0001 (1) Series expansion module Coming soon GSM module MOD-0350* (1) CONTROL MODULES CONNECTED TO THE CONTROL BUS: RFID tag reader connected to BUS MOD-0046N (8) IR module connected to BUS MOD-0055N (8) Blinds module connected to BUS MOD-0105N (50) Expansion module MOD-0035-N(32) Light dimmer module MOD-0450 (50) Light module ON/OFF MOD-0415 (25) *Required MOD-0001 (NOT INCLUIDED) to connect MODULES CONNECTED TO OUTPUTS: Relay module MOD-0031 (1) Blinds module MOD-0102 (Can also be used as slaves of the MOD-0105-N)
Dimensions and included components COVER CHASSIS 273 mm 215 mm 408 mm 305 mm Standard components: (included) - Ref: ALM-0011 / 0021 / 0022 - Ref: VIVIMAT 3.0 - Packaging documentation Expansion plate 05 06 07 08 +V3 01 02 03 04 GND SIN SOUT GND GND TT +V4 +V1 +V1 +V1 +V1 GND +VA GND +VB CN5A CN5B CN27B TP19 exp. Audio Optional components: - Ref: MOD-0035 - Ref: BAT-0190 - Ref: MOD-0350 - Ref: MOD-0360 - Ref: MOD-0001 - Ref: MOD-0200 - Ref: MOD-0800 CN10 CN3 - USB ETHERNET MAIN BOARD OF VIVIMAT 3.0 CN26 Video-doorphone GSM TAMPER MEMORY CARD A1 -V2 GND B1 A2 +V2 GND B2 IN1 IN2 GND IN3 IN4 IN5 IN6 GND IN7 IN8 GND AIN FIN PHONE LINE
Connections EXTERNAL PHONE INTERNAL PHONE ACTUATORS >5A FIRE ACTUATORS >16A MOD-0031 SOUND OF SCREENS SENSORS POWER SUPPLY GROUND 05 06 07 08 +V3 01 02 03 04 GND SIN SOUT GND GND TT +V4 +V1 +V1 +V1 +V1 GND +VA GND +VB CN27B TP19 CN5A CN5B CN10 CN26 MAIN BOARD OF VIVIMAT 3.0 MEMORY CARD A1 +V2 GND B1 A2 +V2 GND B2 IN1 IN2 GND IN3 IN4 IN5 IN6 GND IN7 IN8 GND AIN FIN PHONE LINE TAMPER CONTROL BUS INTERFACE BUS TEMPERATURE DIGITAL SENSORS CONFIGURATION CONTROL MODULES SCREENS FIRE SENSOR POWER SUPPLY ANTISABOTAGE GENERAL POWER SUPPLY SUPPORT BATTERY - Wiring: Power supply 3x1,5mm2. Tel. 2 pairs of rigid telephone wire. Wiring required for the other elements of the system. See wiring requirements of each element.
Installation recommendations - Installation 1: The BOX-0030 (not included) is embedded in the wall of the housing. With 4 screws we fix the controller board to the BOX-0011. Afterwards, we use 4 screws to fix the cover on the BOX-0011. BOX-0030 vivimat 3.0 controll board Cover - Installation 2: As long as the battery is located at the bottom, the vivimat 3.0 controller board can also be placed vertically. Battery localization - Location: Inconspicuous location, ventilated and accessible for repair. FT_VIVIMAT-3.0_23/11/11_ENG Product manufactured by: Dinitel 2000 S.A. - Avda. Otaola 20 20600 Eibar ( Guipúzcoa ) Spain T. +34 902 111 220 / +34 943 820 458 F. +34 902 124 779 www.domotica-vivimat.com dinitel@dinitel.com