Copyright 2013 Pacific Architectural Millwork All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without permission by Pacific Architectural Millwork.
Slide & Seal AW6700 Section Contents Section Contents... 1 Product Overview... 3 Introduction... 3 Wood Species... 3 Glazing Options... 3 Other Options... 3 Product Parameters... 4 Hardware Images... 4 Standard Jamb Depths... 7 Sample Configurations... 8 Clad Muntin Detail... 9 PXX XXP: Exterior Elevation... 10 PXX XXP: Vertical Section at Lead Panel... 11 PXX XXP: Plan Section... 12 PXX XXP: Plan Section (Retracted Panels)... 13 PXX XXP: Head Detail at Lead Panel... 14 PXX XXP: Sill Detail at Lead Panel (Flush Drain Track)... 15 PXX XXP: Sill Detail at Lead Panel (Flush Track)... 16 PXX XXP: Sill Detail at Lead Panel (Low Flush Track)... 17 PXX XXP: Interlocker Detail at Jamb... 18 PXX XXP: Interlocker Detail... 19 PXX XXP: Meeting Panel Detail... 20 OXXO: Exterior Elevation... 21 OXXO: Vertical Section at Lead Panel... 22 OXXO: Plan Section... 23 OXXO: Head Detail at Lead Panel... 24 OXXO: Sill Detail at Lead Panel (Flush Drain Track)... 25 OXXO: Sill Detail at Lead Panel (Flush Track)... 26 OXXO: Sill Detail at Lead Panel (Low Flush Track)... 27 OXXO: Jamb Detail at Fixed Panel... 28 OXXO: Interlocker Detail... 29 OXXO: Meeting Stiles Detail... 30 H7100: Elevation Detail... 31 H7100: Cross Section Detail... 32 1
Meeting Detail (Inside Corner OXX-XXO)... 33 Meeting Detail (Outside Corner OXX-XXO)... 34 Meeting Detail (Inside Corner PXX-XXP)... 35 Meeting Detail (Outside Corner PXX-XXP)... 36 2
Product Overview Introduction Introducing the next step in the evolution of the sliding door: the patent-pending Slide & Seal AW6700 system, available exclusively from Pacific Architectural Millwork. The innovative hardware at the heart of the Slide & Seal automatically seals your door when it reaches the closed position. An independently-operating bottom gasket automatically drops and seals each panel with the surface of the floor, while a mechanism in the head track tilts the panels slightly outward, creating a weather-resistant enclosure around the perimeter. The Slide & Seal AW6700 improves upon Lift & Slide hardware in nearly every way: Simple operation No more bulky and expensive handles needed to operate each panel No need to remove and store handles when you want to stack flush into a pocket Adjustable hardware allows for fine-tuning in the field and self-corrects for variations in the floor surface Motorized option for fully-automated panels that seal The proprietary H7100 handle is crafted out of solid bronze, and remains recessed in the face of the panel until you press the lower part of the handle. The counter-weighted handle then pivots and drops into the open position, allowing you to operate the panels comfortably. And because each panel seals automatically, only one handle per lead panel (with matching exterior flush pull) is required for the entire system. Wood Species Our standard wood species are the following: Pine Vertical Grain Douglas Fir African Mahogany Alternative and exotic wood species are also available. See the Wood Species page in the General Info section. Glazing Options Standard glazing for the Slide & Seal TM AW6700 is 1-1/4 overall tempered insulated glass. Custom glazing and tinted glass are available. Ratings NFRC: 0.40 U-value (1-1/4 Tempered LowE3 IG with Argon) AAMA: Meets/exceeds AAMA LC-PG30-SGD Product Class (w/flush Drain Track option) Other Options The Slide & Seal AW6700 can be purchased with a variety of options such as 1-3/4 aluminum or all-wood screens, wood louvers, simulated divided lites, and intermediate vertical or horizontal rails. Choose from several different track options: Standard Stainless Steel Flush Track (3/16 projection above finish floor; not recommended for wood floors) Flush Drain Track (standard flush track with adjustable-height stainless steel interior drain) Low Stainless Steel Flush Track (required only for special floor conditions) NOTE: Standard/Low Flush tracks are not warranted against air, water, or dust infiltration. With proper maintenance, the Flush Drain track is warranted against water penetration up to 4.59 psf. Contact Pacific Architectural Millwork for additional options. 3
Product Parameters Max Frame Height 144 Min Panel Height 60 Min Panel Width 31-1/2 Max Panel Width 108 (Depending on height height/width ratio should be kept at 2.5 or less for optimal panel operation) Max Glass Size 60 sq ft (Depending on height/weight ratio) Max Opening 30 (larger openings available upon review) Muntin Width 1-1/4 standard (SDL) (SDL option requires Contemporary interior edge detail) Panel Thickness 2-5/8 Screen Thickness Aluminum - 1-3/4" (w/kynar finish) Wood - 1-3/4" (Panel Height<96") Wood - 2-1/4" (Panel Height>96") Stile/Rail Width 3-3/4 Aluminum Finishing Anodized or Custom Color-Matched Kynar TM Finishes Available Edge Detail Exterior Aluminum: Contemporary Interior Wood: Traditional or Contemporary Hardware Images H7100 Handle Oil-Rubbed Bronze Satin Nickel Optional exterior key cylinders* (doors will not stack flush in pocket with this option) Exterior flush pull and interior thumb-turn are standard. 4
5
/ 6
Standard Jamb Depths Contact Pacific Architectural Millwork for jamb depths on systems that include louvers and/or screens (will be shown on shop drawings). JAMB DEPTHS FRAME CONFIGURATION DEPTH² FIXED - ONE SIDE OX 7-9/16 O2X 11 O3X 14-7/16 O4X 17-7/8 O5X 21-5/16 FIXED - SPLIT PANELS O2XO 7-9/16 O4XO 11 O6XO 14-7/16 O8XO 17-7/8 O10XO 21-5/16 CENTER FIXED XOX 7-9/16 2XO2X 11 3XO3X 14-7/16 4XO4X 17-7/8 5XO5X 21-5/16 JAMB DEPTHS FRAME CONFIGURATION DEPTH² POCKET I.D. POCKETING - ONE SIDE¹ PX 4-1/8 5-1/16 P2X 7-9/16 8-1/2 P3X 11 11-15/16 P4X 14-7/16 15-3/8 P5X 17-7/8 18-13/16 POCKETING - SPLIT PANELS¹ P2XP 4-1/8 5-1/16 P4XP 7-9/16 8-1/2 P6XP 11 11-15/16 P8XP 14-7/16 15-3/8 P10XP 17-7/8 18-13/16 Notes: 1 P = Pocket Enclosure 2 Does not include ¼ shim at either side of sill 7
Sample Configurations You can order your Slide & Seal AW6700 in either fixed, pocket, or zero-post corner configurations. The following drawings show some sample configurations. Configuration Key P3X-3XP (PXXX XXXP) P Pocket O Fixed Panel X Moving Panels As viewed from Exterior 8
Clad Muntin Detail 9
PXX XXP: Exterior Elevation 10
PXX XXP: Vertical Section at Lead Panel 11
PXX XXP: Plan Section 12
PXX XXP: Plan Section (Retracted Panels) 13
PXX XXP: Head Detail at Lead Panel 14
PXX XXP: Sill Detail at Lead Panel (Flush Drain Track) 15
PXX XXP: Sill Detail at Lead Panel (Flush Track) 16
PXX XXP: Sill Detail at Lead Panel (Low Flush Track) 17
PXX XXP: Interlocker Detail at Jamb 18
PXX XXP: Interlocker Detail 19
PXX XXP: Meeting Panel Detail 20
OXXO: Exterior Elevation 21
OXXO: Vertical Section at Lead Panel 22
OXXO: Plan Section 23
OXXO: Head Detail at Lead Panel 24
OXXO: Sill Detail at Lead Panel (Flush Drain Track) 25
OXXO: Sill Detail at Lead Panel (Flush Track) 26
OXXO: Sill Detail at Lead Panel (Low Flush Track) 27
OXXO: Jamb Detail at Fixed Panel 28
OXXO: Interlocker Detail 29
OXXO: Meeting Stiles Detail 30
H7100: Elevation Detail 31
H7100: Cross Section Detail 32
Meeting Detail (Inside Corner OXX-XXO) 33
Meeting Detail (Outside Corner OXX-XXO) 34
Meeting Detail (Inside Corner PXX-XXP) 35
Meeting Detail (Outside Corner PXX-XXP) 36