DIMMING COMPATIBILITY: TRACK, WALL SCONCE & PURE LIGHT LAMP 70 O2 LED Track Fixture Series: CTL8051 Compatible with most Electronic Low Voltage and Electronic Low Voltage (ELV) Triac (Incandescent) Triac (Incandescent) Dimmers Lutron Faedra Lutron Skylark Leviton Trimatron Lutron NovaT Lutron Maestro Leviton SureSlide Leviton Acenti Leviton True Torch Leviton Illumitech Cooper Aspire O2 LED Track Fixture Series: CTL8052 and CTL8053 Utlizes the Lutron HiLume A-Series Dimming Driver Compatible Lutron Dimming Controls The following is a general list of compatible Lutron HiLume dimming controls. For specific Lutron part numbers, please refer to www.lutron.com or contact Contech Lighting Technical Support Lutron NovaTa Lutron RadioRA 600W Lutron HomeWorks QS 600W Lutron RPM-4U Module Lutron Maestro Wireless Lutron Radio RA 1000W Lutron HomeWorks QS 1000W Lutron RPM-4A Module Lutron RadioRA 2 1000W Lutron HomeWorks QS Adaptive Dimmer Lutron HomeWorks 600W Dimmer Lutron Stanza Lutron RadioRA 2 Adaptive Dimmer Lutron HomeWorks QS WPM Lutron HomeWorks 1000W Dimmer Lutron HomeWorks WPM Lutron Grafik Eye QS Lutron Grafik Eye 3000 O2 Mini LED Track Fixture Series: CTL8061, CTL8062, and CTL8063 and Triac (Incandescent) Dimmers Lutron Skylark Lutron Diva Lutron Skylark Lutron Maestro Leviton Sureslide Lutron Diva Lutron NovaT Leviton Vizia Leviton Illumatech Leviton Illumatech Optica and LED Cylinder Fixture Series: CTL802818L, CTL802927L, CTL8001, CTL8002, LIR8001, LIR8002 and Triac (Incandescent) Dimmers Lutron Faedra Lutron Skylark Leviton SureSlide Lutron NovaT Lutron Maestro Leviton Illumitech Leviton Acenti Leviton True Torch Cooper Aspire Leviton Trimatron Optica Mini LED Track Fixture Series: CTL804L2 Compatible with most Electronic Low Voltage, Electronic Low Voltage (ELV) Triac (Incandescent) Magnetic Low Voltage and Triac (Incandescent) Dimmers Leviton Sure Slide Leviton Trimatron Deluxe Lutron Skylark Lightolier Sunrise Leviton Decora Lutron Diva Lutron Diva Lightolier MultiSet Pro Lutron Arinadi Magnetic Low Voltage (MLV) Lutron Skylark LED Linear Wall Lighter Fixture Series: CTL170 and CTL171 and Triac (Incandescent) Dimmers Lutron Skylark Lutron Diva Lutron Skylark Lutron Maestro Leviton Sureslide Lutron Diva Lutron NovaT Leviton Vizia Leviton Illumatech Leviton Illumatech Pure Light PAR38 LED Lamp (E26 Base) Products: CL6EM, CL8EM, CTL838/2LEM, CTL8038LEM, CTL5038LEM, CTL603LEM, RL38LEM, RL38ICLEM, RL38ICRLEM, RA638VLEM, RAN38LEM Compatible with most Electronic Low Voltage Dimmers Electronic Low Voltage (ELV) Lutron Faedra Lutron NovaT Lutron Maestro Leviton Acenti Lutron Diva Leviton Sureslide Quadris 12W LED Wall Sconce: WS07512LD and Triac (Incandescent) Dimmers Lutron Faedra Lutron Skylark Leviton SureSlide Lutron NovaT Lutron Maestro Leviton Illumitech Leviton Acenti Leviton True Torch Cooper Aspire Leviton Trimatron 8W LED Pendant: CRS8 Series and Triac (Incandescent) Dimmers. Lutron Faedra Lutron Skylark Leviton SureSlide Lutron NovaT Lutron Maestro Leviton Illumitech Leviton Acenti Leviton True Torch Cooper Aspire Leviton Trimatron Testing has been performed on these dimmers, however, this does not imply any warranty of compatibility or performance.
TRANSFORMER/DRIVER MATRIX FOR MCT-3LED FIXTURE & MRL-3LED PENDANTS This matrix is designed to provide multiple options to powering the MCT-3LED fixture and MRL-3LED pendants. All transformers and drivers must be installed according to National Electrical Code and local building codes. Due to minimum wattage requirements of many electronic transformers, ConTech offers a low wattage Electronic Transformer option, as well as Magnetic Transformers and Drivers. MOUNTING OPTION Mono-Point (MLA-18 or MLA-19) # OF FIXTURES/ TOTAL WATTAGE ELECTRONIC TRANSFORMER MAGNETIC TRANSFORMER 1 Fixture/Up to 4.7W RS1260MLED LVT-150 Up to (2) Fixtures/ Total of 9.4W Up to (3) Fixtures/ Total of 14.1W Up to (4) Fixtures/ Total of 18.8W 5-10 Fixtures/ Total of 23.5W - 47W 11 or More Fixtures/ Total of 51.7W+ DRIVER LED10CV12 RS1260M LED LVT-150 LED10CV12 RS1260M LED LVT-150 LED25 12V RS1260M LED LVT-150 LED25 12V LRT-181, LRT-363, MLA-60 LRT-181, LRT-363, LVT-151, LVT-151 24V, LVT-175-DC, LVT-303, LVT-303 24V, LVT-303-DC, MLA-60, MLA-415, MLA-830 LVT-1200-C-24, LVT-150, LVT-300, LVT-300 277V, LVT-300-24, LVT-500-C, LVT-600-24, LVT-600-277V-24, LVT-600-C LVT-1200-C-24, LVT-150, LVT-300, LVT-300 277V, LVT-300-24, LVT-500-C, LVT-600-24, LVT-600-277V-24, LVT-600-C LED60WDC12V LED100WDC12V 71
DIMMING COMPATIBILITY: 4" & 6" LED DOWNLIGHTS The following ConTech Recessed LED Products are compatible with the dimmers listed below. 4" and 6" 1000 Series: Standard, 0-10V DC and LUTRON Hi-Lume Dimming 4" and 6" 2000 Series: 0-10V DC and LUTRON Hi-Lume Dimming 6" 2700 Series: 0-10V DC and LUTRON Hi-Lume Dimming STANDARD TRIAC DIMMING 4" 1000 SERIES and 6" 1000 SERIES 120V AC Dimming: Incandescent (INC) and Magnetic Low Voltage (MLV) Dimmers Standard 120V AC line voltage dimmers for incandescent and magnetic low voltage loads adjust the light with forward phase control, where the dimmer chops the forward part of the AC wave to deliver less or more power to the light source. No neutral wire connection required. 120V AC Dimming: Electronic Low Voltage (ELV) Dimmers Standard 120V AC line voltage dimmers for electronic low voltage loads adjust the light with reverse phase control, where the dimmer chops the back part of the AC wave to deliver less or more power to the light source. Neutral wire connection required. These systems are typically dimmable to 10%. LED Dimming performance may vary based on dimmer model, manufacturer, circuit wiring and circuit loading. Consult dimmer manufacture for the latest dimmer information. Recommended Dimmers Standard Dimmers: Lutron Skylark Series (Part #s S-600, S2-LH) Lutron Maestro Series (Part # MAW-600) Cooper Aspire Series (Part # 9530XXX) Leviton Illumitech Series (Part # IPI06-XXX) Leviton Trimatron Series (Part #s 6602-X, 6681-X, 6683-X, 6684-X, 700-X, and 705-X) Leviton SureSlide Series (Part # 6631) Leviton True Torch Series (Part # 6606-1LM) Electronic Low Voltage Dimmers: Lutron Nova T Series (Part # NTELV-600) Lutron Faedra (Part # FAELV-500-XX) Leviton Acenti (Part # ACE06-XXX) Dimmer maximum load rating with LED may differ from published traditional source dimmer ratings. Consult manufacturer for maximum dimmer information. 0-10V DC DIMMING 4" 1000 and 2000 SERIES 6" 1000, 2000 and 2700 SERIES 0-10V DC Dimming is a common type of dimming for many commercial applications. Many local codes require the contractor to separate the low and line voltage wiring in the junction box. 0-10V DC Low voltage dimming operates using two low voltage dimming wires that are separate from the 120V or 277V AC power. The 0-10V dimmer switch sends a variable output voltage to the fixture based upon the dimming level. 10V Corresponds to undimmed operation, 5V to 50% and so on. Switching on/off is controlled with the line voltage power (120V or 277V AC) input to the dimmer and then dimming operation is controlled with the 0-10V DC low voltage wiring connection between the dimmer and the LED driver. The control signal runs on two low voltage control wires (color coded violet and gray). These systems are typically dimmable to 15%. LED Dimming performance may vary based on dimmer model, manufacturer, circuit wiring and circuit loading. Consult dimmer manufacture for the latest dimmer information. Recommended Dimmers Lutron DVTV Leviton IP710 LUTRON Hi-Lume DIMMING 4" 1000 and 2000 SERIES 6" 1000, 2000 and 2700 SERIES Lutron Hi-Lume LED A-Series drivers offer high-performance, continuous dimming from 1% - 100%. For a complete list of compatible dimmers and controls, please visit www.lutron.com. NOTES: Consult factory for additional dimming information. Testing has been performed on these dimmers, but this does not imply any warranty of compatibility. 72
NON-DIMMING & DIMMING DRIVERS: ACCENT LIGHTING Because LEDs operate at a lower current than traditional light sources, most LED fixtures must be powered by an LED driver. When selecting a driver, follow these steps: 1. Verify the appropriate current (typically 350mA or 700mA) 2. Select a driver with enough usable wattage for the fixtures you ve selected. 120V AC INPUT 18AWG solid or tinned stranded wire OUTPUT (+) RED (-) BLACK LED DRIVER HOT (BLACK) NEUTRAL (WHITE) WIRE NUT BLACK LED LEAD RED LED LEAD 18-2 CLASS II PLENUM WIRE 18" Included with driver. Additional length available; Part No: 18-2 SOL CL2P LEDs in series should be connected with black wire of one LED to red wire of next LED, etc. All codes requiring Class II splice compartments must be followed. MODEL OUTPUT CURRENT WATTAGE RANGE NON-DIMMING DRIVERS INPUT VOLTAGE. MOUNTING DISTANCE NON-DIMMING DRIVERS DIMMING DRIVERS LENGTH WIDTH HEIGHT LED3503 350mA 1.0W 3.2W 100-240V 65-1/2' 2" 1-5/8" 7/8" LED3512 350mA 1.0W 11.5W 120V 108' 5-1/4" 7/8" 7/8" LED3513 350mA 6.3W - 12.6W 100-240V 65-1/2' 6-5/8" 1-5/8" 1-1/4" LED3518 350mA 10.5W - 18.9W 100-240V 65-1/2' 4-1/8" 2-3/4" 1-1/4" LED7003 700mA 2.0W - 3.5W 100-240V 65-1/2' 2" 1-5/8" 7/8" LED7012 700mA 5.6W - 12.6W 100-240V 65-1/2' 6-5/8" 1-5/8" 1-1/4" LED7017 700mA 2.0W - 16.8W 120V 108' 5-1/4" 1-5/8" 7/8" LED7018 700mA 8.4W - 18.9W 100-240V 65-1/2' 4-1/4" 2-3/4" 1-1/4" DIMMING DRIVERS LED3518D 350mA 2.0W - 14.7W 120V 65' 7-3/4" 1-3/4" 1-1/4" LED7036D 700mA 3.9W - 29.4W 120V 65' 7-3/4" 1-3/4" 1-1/4" Drivers provide constant 350mA or 700mA output DC constant current output Serial connection required from fixture to fixture Short-circuit protection Meets UL, CSA and FCC requirements Class II LED driver must be maintained within an enclosure that meets local building codes and NEC For additional configurations, consult factory Non-Dimming Drivers LED3503-3W/350mA Driver LED7003-3W/700mA Driver LED3513-12W/350mA Driver LED7012-12W/700mA Driver Drivers provide constant current 350mA or 700mA output There must be at least two (2) fixtures on these drivers to operate properly Serial connection required from fixture to fixture Compatible with standard dimmers; leading edge, trailing edge and universal Fully protected: short circuit, input high voltage, inherent thermal protection and over voltage protection Self re-settable Meets UL, CSA and FCC requirements Class II LED driver must be maintained within an enclosure that meets local building codes and NEC For additional configurations, consult factory Dimming Drivers LED3518D - 18W/350mA Dimmable Driver LED7036D - 36W/700mA Dimmable Driver LED3512-12W/350mA Driver LED7017-17W/700mA Driver LED3518-18W/350mA Driver LED7018-18W/700mA Driver LED Driver Accessories 18-2 SOL CL2P - 18-2 Class II Plenum Wire (Sold in Foot Increments) 74
+ + TAPELIGHT DIMMING ConTech LED Tapelight is dimmable utilizing either the TLPDIM10V Dimming Module or the TLPDIMWP Wall Mount Dimmer. The 0-10V Dimming Module (TLPDIM10V) is designed for use with commercially available 0-10V dimmers. 0-10V dimmers are commonly used for LED lighting systems due to their fine performance and reliability. Compatible with quality 0-10V dimmers, this module will dim down to 15%. DC12V POWER SUPPLY 120VAC Cord & Plug or Hard Wire + IN + OPTOTRONIC OT DIM The Wall Mount Dimmer (TLPDIMWP) contains on-board dimming capabilities and dims down to 0%. It has an attractive appearance that blends with most decors and requires no junction box to mount. 120VAC Cord & Plug or Hard Wire POWER SUPPLY DC12V ConTech POWER SUPPLY INPUT VOLTAGE: 12V DC STANDARD OUTPUT WATTS PER FOOT: 1.2 POWER SUPPLY/DISTANCE CHART HIGH OUTPUT WATTS PER FOOT: 1.8 RGB WATTS PER FOOT: 3.9 MODEL NO. TYPE WATTAGE SYSTEM 1 LOAD 2 SYSTEM 1 LOAD 2 SYSTEM 1 LOAD 2 TLP12VP24 Plug -In 24W 30 ft. 20 ft. 30 ft. 13 ft. 20 ft. 6 ft. TLP12VP Plug-In 36W 30 ft. 30 ft. 30 ft. 20 ft. 20 ft. 9 ft. TLP12VHW20 Hardwire 20W 30 ft. 16.5 ft. 30 ft. 11 ft. 20 ft. 5 ft. TLP12VHW60 Hardwire 60W 30 ft. 50 ft. 3 30 ft. 33.3 ft. 3 20 ft. 15.4 ft. 1. Distance from first LED tape section to end of LED tape run. Exceeding this length may result in inconsistent light output from beginning to end of the LED tape run. 2. Overall distance of LED tape under load [illuminated sections]. If exceeded damage to the power supply and LED tape may result. 3. If maximum load run exceeds maximum system run, multiple runs from power supply may be employed as long as maximum load run is not exceeded. POWER SUPPLY WIRING CHART (Copper Wire) Wire Gauge 20 18 16 14 12 Distance* 6 ft. 10 ft. 15 ft. 23 ft. 40 ft. *Power Supply to First LED Tape Section 75