CONTENTS Page - SPECIFICATIONS SPECIFICATIONS : DML 200 SPECIFICATIONS : DMLV 20 SELECTION CHART 202 SELECTION CHART : 80DML 203 SELECTION CHART : 00DML 204 SELECTION CHART : 50DML 205 SELECTION CHART : 80DMLV 206 SELECTION CHART : 00DMLV 207 PERFORMANCE CURVE 80DML52.2 208 PERFORMANCE CURVE 80DML53.7 209 PERFORMANCE CURVE 00DML53.7 20 PERFORMANCE CURVE 00DML55.5 2 PERFORMANCE CURVE 00DML57.5 22 PERFORMANCE CURVE 00DML5 23 PERFORMANCE CURVE 00DML55 24 PERFORMANCE CURVE 00DML522 25 PERFORMANCE CURVE 50DML55.5 26 PERFORMANCE CURVE 50DML57.5 27 PERFORMANCE CURVE 50DML5 28 PERFORMANCE CURVE 50DML55 29 PERFORMANCE CURVE 50DML522 220 PERFORMANCE CURVE 80DMLV52.2 22 PERFORMANCE CURVE 80DMLV53.7 222 PERFORMANCE CURVE 00DMLV55.5 223 PERFORMANCE CURVE 00DMLV57.5 224 PERFORMANCE CURVE 00DMLV5 225 PERFORMANCE CURVE 00DMLV55 226 PERFORMANCE CURVE 00DMLV522 227 - CONSTRUCTIONS SECTIONAL VIEW 80DML52.2 300 SECTIONAL VIEW 80 (00) (50) DML (3.7 7.5 kw) 30 SECTIONAL VIEW 00 (50) DML ( 22 kw) 302 SECTIONAL VIEW : 80DMLV52.2 303 SECTIONAL VIEW : 00DMLV (3.7 7.5 kw) 304 SECTIONAL VIEW : 00DMLV ( 22 KW) 305 SECTIONAL VIEW KIT CONNECTOR LM80 (OPTIONAL) 306 SECTIONAL VIEW KIT CONNECTOR LL00 (OPTIONAL) 307 00
CONTENTS Page - DIMENSIONS DIMENSIONS OF PUMPS : DML 400 DIMENSIONS OF PUMPS : DMLV 40 DIMENSIONS KIT CONNECTOR LM80 (OPTIONAL) (DML) 402 DIMENSIONS KIT CONNECTOR LM80 (OPTIONAL) (DMLV) 403 DIMENSIONS KIT CONNECTOR LL00 (OPTIONAL) (DML) 404 DIMENSIONS KIT CONNECTOR LL00 (OPTIONAL) (DMLV) 405 - TECHNICAL DATA TECHNICAL DATA : MOTOR 500 TECHNICAL DATA : AUTO CUT 50 TECHNICAL DATA MINIATURE THERMAL PROTECTORS 502 TECHNICAL DATA : MECHANICAL SEAL AND CABLE 503 0
SPECIFICATIONS : DML PUMP Discharge [ mm ] 80-50 Motor Power [ kw ] 2.2-22 Scope Capacity [ m 3 /h ] 2-330 Performance Head [ m ] 4-40 Type Sewage Liquid Maximum temperature [ C ] 40 Maximum diameter of solids [ mm ] 76 Length fibrous shape [ mm ] 500 mm Submergence Maximum [ m ] 8 Minimum Refer to low water level (L.W.L.) in dimensions Construction Impeller Non-clog single channel Mechanical seal Oil lubrificated, double mechanical seals Casing Impeller Shaft 403 Stainless steel Motor frame Materials Fasteners 304 Stainless steel Mechanical seal Upper Faces: Carbon / Ceramic/NBR Lower Faces: SiC / SiC/NBR Lubrificating Oil: Turbine Oil VG32 (SAE0W/20W) Accessories Kit connector Applicable standard of test ISO 9906 annex A MOTOR Type Air filled dry submersible Three Phase No. of Poles 4 Insulation Class Class F Protection degree IP 68 Nominal Speed [ min - ] 450 Motor Frequency [ Hz ] 50 Voltage [ V ] 380/400/45 Starting DOL (2.2 kw) Delta (3.7 to 22kW) Protection In built overload protection (2.2 kw) Miniature thermal protector (3.7 to 22 kw) Bearings Sealed ball bearing with permanent grease Cable Lenght [ m ] 0 200
SPECIFICATIONS : DMLV PUMP Discharge [ mm ] 80-00 Motor Power [ kw ] 2.2-22 Scope Capacity [ m 3 /h ] 2-68 Performance Head [ m ] 29,4-40 Type Sewage Maximum temperature [ C ] 40 Liquid Maximum diameter of solids [ mm ] Equivalent to the pump diameter Length fibrous shape [ mm ] Ø 80 : 400 mm Ø 00 : 500 mm Submergence Maximum [ m ] 8 Minimum Refer to low water level (L.W.L.) in dimensions Construction Impeller Vortex Mechanical seal Oil lubrificated, double mechanical seals Casing Impeller Shaft 403 Stainless steel Motor frame Materials Fasteners 304 Stainless steel Mechanical seal Upper Faces: Carbon / Ceramic/NBR Lower Faces: SiC / SiC/NBR Lubrificating Oil: Turbine Oil VG32 (SAE0W/20W) Accessories Kit connector Applicable standard of test ISO 9906 annex A MOTOR Type Air filled dry submersible Three Phase No. of Poles 4 Insulation Class Class F Protection degree IP X8 Nominal Speed [ min - ] 450 Motor Frequency [ Hz ] 50 Voltage [ V ] 380/400/45 Starting DOL (2.2 kw) Delta (3.7 to 22kW) Protection In built overload protection (2.2 kw) Miniature thermal protector (3.7 to 22 kw) Bearings Sealed ball bearing with permanent grease Cable Lenght [ m ] 0 20
SELECTION CHART Pump: 80 DML 5 2.2 2.2 3.7 OUTPUT kw 5.5 7.5 5 PUMP TYPE DML (Sewage pump) 22 DMLV (Vortex pump) OUTLET DIAMETER OF ELBOW 80 00 50 Kit connector (accessory) : LM 80 OUTLET PUMP DIAMETER 80 00 TYPE LM LL 202
SELECTION CHART : 80DML 80DML PUMP TYPE DML kw HP Q= Capacity [l/min] 0 200 400 600 800 000 200 400 600 [m 3 /h] 0 2 24 36 48 60 72 84 96 H=Total manometric head [ m ] 80DML52.2 2.2 3-3..2 9.6 8.2 7. 6.2 5.5 4.9 4 80DML53.7 3.7 5-7.9 5.8 4.2 2.8.7 0.7 9.7 8.8 7.9 203
SELECTION CHART : 00 DML 00DML PUMP TYPE DML kw HP Q= Capacity [l/min] 0 500 000 300 600 900 2200 2400 2500 [m 3 /h] 0 30 60 78 96 4 32 44 50 H=total manometric head [ m ] 00DML53.7 3.7 5-7.9 3.5 0.7 9.3 7.9 6.5 5 4 _ 00DML55.5 5.5 7.5-22 7.9 4.9 3.4.9 0.6 9.3 8.5 _ 00DML57.5 7.5 0-25.3 20.6 8 6.7 5.5 4.2 3 2. _ 00DML5 5-30.3 27.5 25.2 23.7 22.2 20.7 9. 8 7.5 00DML55 5 20-35 33.5 3.3 29.8 28.3 26.7 25. 24 23.4 00DML522 22 30-40 38.5 36.4 34.9 33.3 3.7 30 28.7 28 204
SELECTION CHART 50DML 50DML PUMP TYPE kw HP Q= Capacity DML [l/min] 0 000 2000 2500 3000 3400 4000 4500 5000 5500 [m3/h] 0 60 20 50 80 204 240 270 300 330 H=total manometric head [ m ] 50DML55.5 5,5 7,5-22 4,9 0, 8 5,9 3,9 - - - - 50DML57.5 7,5 0-25,3 8 3,7,6 9,5 7,5 4 - - - 50DML5 5-30,3 25,2 20,2 7,5 4,7 2,2 8,6 5,4 - - 50DML55 5 20-35 3,3 26, 23,4 20,6 8,2 4,8,9 8,6-50DML522 22 30-40 36,4 3, 28 25,2 22,9 9,5 6,8 3,8 0,5 205
SELECTION CHART : 80DMLV 80DMLV PUMP TYPE DMLV kw HP Q= Capacity [l/min] 0 200 400 600 800 000 200 400 [m 3 /h] 0 2 24 36 48 60 72 84 H=Total manometric head [ m ] 80DMLV52.2 2,2 3-0,7 9,9 9,0 8,0 6,8 5,6 4,0-80DMLV53.7 3,7 5-2,8 2,0,4 0,7 9,9 9, 8,0 6,4 206
SELECTION CHART : 00DMLV 00DMLV PUMP TYPE DMLV kw HP Q= Capacity [l/min] 0 600 800 000 200 400 700 2000 2400 2800 [m 3 /h] 0 36 48 60 72 84 02 20 44 68 H=Total manometric head [ m ] 00DMLV5,5 5,5 7,5-3,2, 0,6 0, 9,7 9, 7,9 6,4 - - 00DMLV57,5 7,5 0-6,8 5,4 4,9 4,3 3,7 3,0,6 0,0 7,0-00DMLV5 5-20,6-8,8 8,2 7,6 6,9 5,8 4,5 2,4 9,9 00DMLV55 5 20-24,9 - - 23,4 23,0 22,5 2,7 20,7 9,0 6,0 00DMLV522 22 30-32, - - 29,4 29, 28,7 28,2 27,5 26,5 25,0 207
PERFORMANCE CURVE 80DML52.2 Impeller diameter = 79 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 208
PERFORMANCE CURVE 80DML53.7 Impeller diameter = 20 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 209
PERFORMANCE CURVE 00DML53.7 Impeller diameter = 20 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 20
PERFORMANCE CURVE 00DML55.5 Impeller diameter = 232 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 2
PERFORMANCE CURVE 00DML57.5 Impeller diameter = 248 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 22
PERFORMANCE CURVE 00DML5 Impeller diameter = 286 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 23
PERFORMANCE CURVE 00DML55 Impeller diameter = 309 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 24
PERFORMANCE CURVE 00DML522 Impeller diameter = 330 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 25
PERFORMANCE CURVE 50DML55.5 Impeller diameter = 232 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 26
PERFORMANCE CURVE 50DML57.5 Impeller diameter = 248 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 27
PERFORMANCE CURVE 50DML5 Impeller diameter = 286 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 28
PERFORMANCE CURVE 50DML55 Impeller diameter = 309 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 29
PERFORMANCE CURVE 50DML522 Impeller diameter = 330 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 220
PERFORMANCE CURVE 80DMLV52.2 Impeller diameter = 85 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 22
PERFORMANCE CURVE 80DMLV53.7 Impeller diameter = 204 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 222
PERFORMANCE CURVE 00DMLV55.5 Impeller diameter = 2 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 223
PERFORMANCE CURVE 00DMLV57.5 Impeller diameter = 23 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 224
PERFORMANCE CURVE 00DMLV5 Impeller diameter = 25 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 225
PERFORMANCE CURVE 00DMLV55 Impeller diameter = 268 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 226
PERFORMANCE CURVE 00DMLV522 Impeller diameter = 300 mm Rotation speed 450 min - Test fluid : clean water at 20 C Applicable standard of test : ISO 9906 annex A 227
SECTIONAL VIEW : DML 80 DML 52.2 50Hz N PART.NAME MATERIAL 00 Pump Casing 06 Mechanical Seal Cover 02 Impeller No.FOR UNIT N PART.NAME MATERIAL No.FOR UNIT 802 Stator - 8 Submersible Cable - 2 84 Motor Frame 080 Bushing Steel 86 Power Side Bracket 07 Wearing ring Bronze 87 Opposite Side Bracket Mechanical seal - 830 Shaft EN.4006 (AISI403) 74 Discharge Bend 849- Ball Bearing - 93 Oil Plug NBR/Stainless Steel set 849-2 Ball Bearing - 2 Airvent Valve Brass 876 Auto Cut - 3 Stainless steel A2-70 275 Impeller Bolt 904 Lifting Hanger Steel class ISO 3506/ 80 Rotor - 907 Bearing Cover Steel 300
SECTIONAL VIEW : DML 80 (00) (50) DML (3.7 7.5kW) 50Hz N PART.NAME MATERIAL No.FOR No.FOR N PART.NAME MATERIAL UNIT UNIT 00 Pump Casing Submersible Cable 8- (power) - 2 06 Mechanical Seal Cover Submersible Cable 8-2 (signal) - 02 Impeller 84 Motor Frame 080 Bushing Steel 86 Power Side Bracket 07 Wearing ring Bronze 87 Opposite Side Bracket Mechanical seal - 830 Shaft EN.4006 (AISI403) 74 Discharge Bend 849- Ball Bearing - 93 Oil Plug NBR/Stainless Steel set 849-2 Ball Bearing - 2 Airvent Valve Brass 856 Thermal Protector - 3 Stainless steel A2-70 275 Impeller Bolt 904 Lifting Hanger Steel class ISO 3506/ 80 Rotor - 907 Bearing Cover Steel 802 Stator - 30
SECTIONAL VIEW : DML 00 (50) DML ( 22kW) 50Hz N PART.NAME MATERIAL No.FOR No.FOR N PART.NAME MATERIAL UNIT UNIT 00 Pump Casing Submersible Cable 8- (power) - 2 06 Mechanical Seal Cover Submersible Cable 8-2 (signal) - 02 Impeller 84 Motor Frame 080 Bushing Steel 86 Power Side Bracket 07 Wearing ring Bronze 87 Opposite Side Bracket Mechanical seal - 830 Shaft EN.4006 (AISI403) 74 Discharge Bend 849- Ball Bearing - 93 Oil Plug NBR/Stainless Steel set 849-2 Ball Bearing - 2 Airvent Valve Brass 856 Thermal Protector - 3 Stainless steel A2-70 275 Impeller Bolt 904 Lifting Hanger Steel class ISO 3506/ 80 Rotor - 907 Bearing Cover Steel 802 Stator - 302
SECTIONAL VIEW : DMLV 80 DMLV 52.2 50Hz N PART.NAME MATERIAL No.FOR UNIT N PART.NAME MATERIAL 00 Pump Casing 8 Submersible Cable - 2 06 Mechanical Seal Cover 84 Motor Frame 02 Impeller 86 Power Side Bracket 080 Bushing Steel 87 Opposite Side Bracket Mechanical seal - 830 Shaft EN.4006 (AISI403) 74 Discharge Bend 849- Ball Bearing - 93 Oil Plug NBR/Stainless Steel set 849-2 Ball Bearing - 275 Impeller screw Stainless steel A2-70 class ISO 3506/ 876 Auto Cut - 80 Rotor - 904 Lifting Hanger Steel 802 Stator - 907 Bearing Cover Steel No.FOR UNIT 303
SECTIONAL VIEW : DMLV DMLV (3.7 7.5kW) 50Hz N PART.NAME MATERIAL No.FOR No.FOR N PART.NAME MATERIAL UNIT UNIT 00 Pump Casing Submersible Cable 8- (power) - 2 06 Mechanical Seal Cover Submersible Cable 8-2 (signal) - 02 Impeller 84 Motor Frame 080 Bushing Steel 86 Power Side Bracket Mechanical seal - 87 Opposite Side Bracket 74 Discharge Bend 830 Shaft EN.4006 (AISI403) 93 Oil Plug NBR/Stainless Steel set 849- Ball Bearing - 275 Impeller screw Stainless steel A2-70 class ISO 3506/ 849-2 Ball Bearing - 80 Rotor - 904 Lifting Hanger Steel 802 Stator - 907 Bearing Cover Steel 304
SECTIONAL VIEW : DMLV DMLV ( 22kW) 50Hz N PART.NAME MATERIAL No.FOR No.FOR N PART.NAME MATERIAL UNIT UNIT 00 Pump Casing Submersible Cable 8- (power) - 2 06 Mechanical Seal Cover Submersible Cable 8-2 (signal) - 02 Impeller EN-GHJL-200-EN 56 ( kw) 84 Motor Frame EN-GJS-400 -EN 563 (5-22 kw) 080 Bushing Steel 86 Power Side Bracket Mechanical seal - 87 Opposite Side Bracket 74 Discharge Bend 830 Shaft EN.4006 (AISI403) 93 Oil Plug NBR/Stainless Steel set 849- Ball Bearing - 275 Impeller screw Stainless steel A2-70 class ISO 3506/ 849-2 Ball Bearing - 80 Rotor - 904 Lifting Hanger Steel 802 Stator - 907 Bearing Cover Steel 305
SECTIONAL VIEW : KIT CONNECTOR LM80 (Optional) N PART.NAME MATERIAL No.FOR UNIT N PART.NAME MATERIAL 7- Gasket NBR Rubber 35 Washer AISI 304 Stainless Steel 2 7-2 Gasket Aramide fibers 74 Discharge Bend 20- Bolt AISI 304 Stainless Steel 4 74 Sliding Guide Spheroidal graphite cast iron EN-GJS-400 - EN 563 20-3 Bolt AISI 304 Stainless Steel 2 742- QCD Body 20-4 Bolt & Nut AISI 304 Stainless Steel 4 743 Suspension Bar AISI 304 Stainless Steel 28- Nut AISI 304 Stainless Steel 2 747- Guide Pin Steel 4 28-2 Nut AISI 304 Stainless Steel 2 747-2 Guide Support Steel 30- Set Screw AISI 304 Stainless Steel Note: Those parts with item number indicated in a are supplied with the pump. No.FOR UNIT 306
SECTIONAL VIEW : KIT CONNECTOR LL00 (Optional) N PART.NAME MATERIAL No.FOR UNIT 7- Gasket NBR Rubber 35 Washer AISI 304 Stainless Steel 2 7-2 Gasket Aramide fibers 74 Discharge Bend 20- Bolt AISI 304 Stainless Steel 4 74 Sliding Guide Spheroidal graphite cast iron EN-GJS-400 - EN 563 20-3 Bolt AISI 304 Stainless Steel 2 742- QCD Body 20-4 Bolt & Nut AISI 304 Stainless Steel 4 742-2 QDC Flange 20-6 Bolt AISI 304 Stainless Steel 4 743 Suspension Bar AISI 304 Stainless Steel 28- Nut AISI 304 Stainless Steel 2 747- Guide Pin Steel 4 28-2 Nut AISI 304 Stainless Steel 2 747-2 Guide Support Steel 30- Set Screw AISI 304 Stainless Steel N PART.NAME Note: Those parts with item number indicated in a are supplied with the pump. MATERIAL No.FOR UNIT 307
DIMENSIONS OF PUMPS : DML Note: ) L.W.L (Low water Level) is limited: to 0 minutes operation at low water level. 2) It is limited to 30 minutes operation with water level below top of motor. Discharge Flange Dimensions PN 0 According to EN 092-2 DA DG DE DF DT No.DN DD 80 38 60 200 22 8 00 58 80 220 24 8 50 22 240 285 26 22 PUMP TYPE DML DIMENSIONS DA kw A B C D E F H J L L2 WEIGHT [kg] 80 DML52.2 2.2 668 547 80 80 542 385 80DML53.7 3.7 320 57 285 308 20 279 87 727 627 00DML53.7 3.7 582 425 35 33 89 00DML55.5 5.5 2 658 38 470 88 360 339 824 255 30 724 00DML57.5 7.5 25 00 00DML5 60 75 455 530 22 420 355 938 35 329 778 00DML55 5 66 00DML522 22 795 497 550 245 440 358 02 335 342 84 226 50DML55.5 5.5 27 75.5 38 527.5 88 385 369 824 255 30 724 50DML57.5 7.5 32 50DML5 50 66 808.5 455 587.5 22 445 385 938 35 329 778 50DML55 5 72 50DML522 22 852.5 497 607.5 245 465 388 02 335 342 84 232 400
DIMENSIONS OF PUMPS : DMLV ) L.W.L (Low water Level) is limited: to 0 minutes operation at low water level. 2) It is limited to 30 minutes operation with water level below top of motor. Discharge flange dimensions PN 0 According to EN 092-2 PUMP TYPE DMLV DIMENSIONS DA kw DE DF DG DT N D A B C D E F H J L L2 80DMLV52.2 2,2 60 200 38 22 8 8 58 285 375 43 275 254 660 200 200 560 70 80 80DMLV53.7 3,7 60 200 38 22 8 8 58 285 375 43 275 254 72 200 200 620 80 00DMLV55.5 5,5 80 220 58 24 8 22 584 308 430 54 320 305 860 25 250 760 05 00DMLV57.5 7,5 80 220 58 24 8 22 64 352 465 76 355 305 860 250 250 760 20 00DMLV5 00 80 220 58 24 8 22 64 352 465 76 355 305 970 250 250 80 50 00DMLV55 5 80 220 58 24 8 22 728 426 55 23 405 305 970 300 250 80 80 00DMLV522 22 80 220 58 24 8 22 728 426 55 23 405 305 045 300 250 865 235 Weight [kg] 40
DIMENSIONS KIT CONNECTOR LM80 Applicable Models 80 (00) DML 52.2, 53.7 Note: ) For detailed dimensions of the pumps, refer to separate dimension data sheets. 2) The discharge bend supplied with the pump are used with the QDC. 3) The weight in dimension tables refers only to the weight of the QDC. Discharge Flange Dimensions PN 0 According to EN 092-2 DA DG DE DF DT No.DN DD 80 38 60 200 22 8 8 00 58 80 220 24 PUMP TYPE DML A P P2 G G2 F H H2 L L6 BN BN2 D E KIT CONNECTOR WEIGHT [ kgf ] 80 DML 52.2 80 DML 53.7 492 75 90 25 65 295 75 230 00DML53.7 95 300 279 7 75 90 5 55 LM80 7 402
DIMENSIONS KIT CONNECTOR LM80 Applicable Models 80DMLV 52.2 80DMLV53.7 Note: ) For detailed dimensions of the pumps, refer to separate dimension data sheets. 2) The discharge bend supplied with the pump are used with the QDC. 3) The weight in dimension tables refers only to the weight of the QDC. Discharge Flange Dimensions PN 0 According to EN 092-2 PUMP TYPE DMLV A P P2 G G2 F H H2 H3 L L6 BN BN2 D E KIT CONNECTOR WEIGHT [ kgf ] 80 DMLV52.2 468 75 90 25 65 285 75 230 280 200 3 75 90 5 55 80 DMLV53.7 468 75 90 25 65 285 75 230 280 200 3 75 90 5 55 LM80 7 403
DIMENSIONS KIT CONNECTOR : LL00 (DML) Applicable Models 00 (50) DML Note: ) For detailed dimensions of the pumps, refer to separate dimension data sheets. 2) The discharge bend supplied with the pump are used with the QDC. 3) The weight in dimension tables refers only to the weight of the QDC. Discharge Flange Dimensions PN 0 Acoording to EN 092-2 DA DG DE DF DT No.DN DD 00 58 80 220 24 8 8 50 22 240 285 26 22 PUMP TYPE DML A P P2 G G2 F H H2 L L6 BN BN2 BM BY BW DM I D E KIT CONNECTOR WEIGHT [ kgf ] 00DML55.5 628 30 3 00DML57.5 00DML5 20 370 72 329 5 00DML55 00DML522 765 342 2 05 05 85 240 265 50DML55.5 628 30 3 50DML57.5 50DML5 235 400 72 329 5 50DML55 50DML522 765 342 2 00 40 220 80 230 800 000 800 000 700 9 75 LL00 46kg 404
DIMENSIONS KIT CONNECTOR : LL00 (DMLV) Applicable Models DMLV Note: ) For detailed dimensions of the pumps, refer to separate dimension data sheets. 2) The discharge bend supplied with the pump are used with the QDC. 3) The weight in dimension tables refers only to the weight of the QDC. PUMP TYPE DMLV A H3 L KIT CONNECTOR WEIGHT [ kgf ] Discharge Flange Dimensions PN 0 According to EN 092-2 00DMLV55,5 554 335 250 00DMLV57,5 6 335 250 00DMLV5 6 335 250 00DMLV55 698 335 300 00DMLV522 698 335 300 LL00 46 405
TECHNICAL DATA : MOTOR Output kw 2,2 3,7 5,5 7,5 5 22 Phase Poles Insulation Class Voltage [V] 400 400 690 400 690 400 690 400 690 400 690 400 690 Full Current [ A ] 5,2 8,4 4,8 2,6 7,3 6,9 9,8 23,8 3,7 3 7,9 42 24,2 Load Efficiency % 69,5 72,7 74,5 79 77,4 80,2 86,5 Power factor % 87,6 87,4 84,3 80,9 85,8 86,8 87,3 Locked Rotor Torque % 204 226-252 - 256-70 - 95-72 - Start Current [ A ] 25,7 48, - 82,6-6,5-36 - 2,9-38,5 - N starts per hour 20 Voltage Tolerance Frequency Tolerance GD 2 [ kgxm 2 ] 0,020 3 4 F ±0% ±5% 0,030 0,059 0,076 0,20 0,60 0,340 500
TECHNICAL DATA AUTO CUT Applicable to 2.2 kw The three pole auto-cuts model is illustrated below. The Auto-Cut consists on: 3 sets of contacts, snap-acting disk, 3 heaters, 3 terminals and calibration bolt and nut, all enclosed in a bakelite housing. The Auto-Cut is installed directly over the motor winding of the motor where it not only senses over heating of the winding but also axcess amperage draw by each winding. Figure 2 shows the Auto-Cut in its normal operating condition (contact closed). When actuating temperature is reached, the snap acting disc opens to interrupt the circuit as shown in figure 3 and stops the motor. When the motor temperature cools down to the safe operating temperature, the snap acting disc resets automatically to the original position as shown in figure 2 and the motor restart! Auto-Cut Part Numbers Phase Power kw Auto-Cut Three 2,2 KA-33-GCLXL02 50
TECHNICAL DATA MINIATURE THERMAL PROTECTORS Applicable from 3.7 to 22 kw A Miniature Thermal Protector (MTP) is embedded in each winding of the motor as illustrated below, and provides automatic cut off with manual reset. When the temperature of the windings increases and reaches the MTP acting point, an external motor protection circuit (not supplied) is activated. Specification Model Klixon 9700K-46-25 Type of contact b (Normally-Closed, Acting-Open) Acting temperature 50 C (+/-5) Re-setting temperature Contact rating 00 C DC24V-8A DC230V-3A 502
TECHNICAL DATA kw Type Diameter [mm] Model DML Mechanical Seal Lubrication Capacity [cm 3 ] DMLV Type Lower side Bearings Upper side 2,2 3,7 30 EAN-30 00 5307ZZ 6205ZZ 5,5 Turbine Oil 40 EAN-40 600 780 7,5 SAE 0W or SAE 20W (Turbine Oil #32) 2900 3380 5 45 EAN-45 5309ZZ 530ZZ 6306ZZ 6308ZZ 22 3000 3550 532ZZ 6309ZZ No. Part Material Rubber part (motor side) NBR 2 Stationary seal ring (motor side) Ceramic 3 Rotary seal ring (motor side) Carbon Graphite 4 Spring EN.430 (AISI304) 5 Rotary seal ring (pump side) Silicon Carbide 6 Stationary seal ring (pump side) Silicon Carbide 7 Rubber part (pump side) NBR kw Starting method Length of cable Cable material Power Cable Number & size of conductor Protector Cable Cross section conductor area Overall diameter [mm] Cross section conductor area Overall diameter [mm] 2,2 DOL 0m H07RN-F 4x,5 mm 2,2 - - 3,7 Y 0m H07RN-F 4x,5 mm 2 x 2 cables,2 2x mm 2 8,7 5,5 Y 0m H07RN-F 4x,5 mm 2 x 2 cables,2 2x mm 2 8,7 7,5 Y 0m H07RN-F 4x,5 mm 2 x 2 cables,2 2x mm 2 8,7 Y 0m H07RN-F 4x4 mm 2 x 2 cables 5,4 2x mm 2 8,7 5 Y 0m H07RN-F 4x4 mm 2 x 2 cables 5,4 2x mm 2 8,7 22 Y 0m H07RN-F 4x6 mm 2 x 2 cables 8, 2x mm 2 8,7 503