www.atos.com Table A60/E Axial piston pumps type PVP variable displacement, by a full line of mechanical controls PVPH4046 PVP are variable displacement axial piston pumps for high pressure operation, with low noise level, suitable for hydraulic oils or synthetic fluids having symilar lubricating characteristics. The actual displacement is dependent on the lenght of stroke of the pumping pistons. This lenght of stroke is determined by the position of the swashing plate that is achieved by two servo pistons with differential areas, against a spring. The rotating barrel forces the pistons in a circular path in and out of the barrel and fluid displacement takes place. Typical section on side shows version H with manual pressure compensator and venting solenoid valve. The available hydraulic controls are shown in sections. The wide range of electrohydraulic proportional controls is shown in tab. A70. SAE J744 mounting flange and shaft (see note ). Max displacement: 29467388 cm 3 /rev. Max pressure: 280 bar working 350 bar peak. MODEL ODE PVP X2E 4 046 / 3044 / D I X 24D 0 /* Variable displacement axial piston pump Eventual suffix for double pumps X2E = with a fixed displacement pump type PFE (see tab. A005) Series number Synthetic fluids: WG = waterglycol PE = phosphate ester See notes in section Type of control (see section ): = manual pressure compensator H = manual pressure compensator, with venting R = remote pressure compensator L = load sensing (pressure & flow) LW= constant power (combined pressure & flow) For electrohydraulic proportional controls, see table A70 Size: 3 = for displacement 029 4 = for displacement 046 5 = for displacement 073 and 090 Supply voltage, see section : 00 = solenoid valve without coils (only for OI solenoid) X = without connector See section for available connectors, to be ordered separately Solenoid of pilot valve: I = solenoid OI (DHI) for A and D supply Max displacement of axial piston pump: 029 = 29 cm 3 /rev 046 = 46 cm 3 /rev 073 = 73 cm 3 /rev 090 = 88 cm 3 /rev Type of PFE (for double pumps), see tab. A005 ) pumps with ISO 309/2 mounting flange and shaft (option /M) are available on request 2 OPERATG HARATERISTIS Direction of rotation (viewed at the shaft end) D = clockwise S = counterclockwise Shaft (SAE Standard) (): = keyed (7/8 for 029 for 046 /4 for 073 and 090) 5 = splined (3 teeth for 029 5 for 046 4 for 073 and 090) Pump model PVP*3029 PVP*4046 PVP*5073 PVP*5090 External load position Displacement [cm 3 /rev] 29 46 73 88 Theoretical max flow at 450 rpm [l/min] 42 66,7 05,8 27,6 Max working pressure / Peak pressure[bar] 280/350 280/350 280/350 250/35 Min/Max inlet pressure [bar abs.] 0,8 / 25 0,8 / 25 0,8 / 25 0,8 / 25 Max pressure on drain port [bar abs.],5,5,5,5 Power consumption at 450 rpm and at [kw] 9,9 3,6 50, 54, maximum pressure and displacement Type Type 5 Type Type 5 Type Type 5 Type Type 5 Max torque on the first shaft [Nm] 200 90 230 330 490 620 490 620 Max permissible load Fax 000 500 2000 2000 [N] on drive shaft Frad 500 500 3000 3000 Speed rating [rpm] 600 3000 600 2600 600 2200 600 850 Fax = axial load Frad = radial load Notes: For speeds over 800 rpm the inlet port must be under oil level with adequate pipes. Maximum pressure for all models with option /WG is 60 bar, with option /PE is 90 bar. Max speed with options /WG and /PE is 2000/900/600/500 rpm respectively for the four sizes. A60
3 MA HARATERISTIS OF VARIABLE DISPLAEMENT AXIAL PISTON PUMP TYPE PVP Installation position Ambient temperature Fluid Recommended viscosity Any position. The drain port must be on the top of the pump. Drain line must be separated and unrestricted to the reservoir and extended below the oil level as far from the inlet as possible. Suggested maximum line lenght is 3 m. from 20 to +70 Hydraulic oil as per D 5524...535; for other fluids see section 5 00 mm 2 /sec at 40 (ISO VG 5 00). Maximum startup viscosity: 000 mm 2 /sec Fluid contamination class ISO 6/3 (filters at 0 µm value with ß0 75 recommended) Fluid temperature 20 +60 20 +50 (seals /WG) 20 +80 (seals /PE) 3. oils characteristics (for version H) Insulation class H onnector protection degree IP 65 Relative duty factor 00% Supply voltage and frequency See electric feature Supply voltage tolerance ± 0% 4 ELETRI ONNETORS AORDG TO D 43650 FOR VERSION H The connectors must be ordered separately ode of connector SP666 SP667 Function onnector IP65, suitable for direct connection to electric supply source As SP666 connector IP65 but with builtin signal led, suitable for direct connection to electric supply source 5 ELETRI FEATURES FOR VERSION H Type of solenoid OI External supply nominal voltage ±0% () DIRET URRENT ALTERNATE URRENT 6 D 2 D 24 D 48 D 0/50 A (2) 20/60 A 230/50 A (2) 230/60 A Type of connector SP666 or SP667 SP666 or SP667 Power consumption (3) 33 W 60 VA (4) ode of spare coil SPOU6D /80 SPOU2D /80 SPOU24D /80 SPOU48D /80 SPOI0/50/60A /80 SPOI20/60A /80 SPOI230/50/60A /80 SPOI230/60A /80 olour of coil label brown green red silver yellow white light blue silver () For other supply voltages available on request see technical table E00. (2) oil can be supplied also with 60 Hz of voltage frequency: in this case the performances are reduced by 0 5% and the power consumption is 55 VA. (3) Average values based on tests performed at nominal hydraulic condition and ambient/coil temperature of 20. (4) When solenoid is energized, the inrush current is approx 3 times the holding current. Inrush current values correspond to a power consumption of about 50 VA. 6 STALLATION POSITION VERTIAL STALLATION D B B B B A The pump is supplyed whit drain open, and D plugged. Before installation fill the pump with hydraulic oil for at least 3/4 of its volume, keeping it in horizontal position. With exception of pump mounted below the oil level, we recomend to interpose a baffle plate between inlet and drain line. SIDE THE TANK Minimum oil level equal or above the pump mounting surface. A 200mm SIDE THE TANK Minimum oil level below the pump mounting surface. Minimum inlet pressure = 0,8 bar absolute B 800mm, = 200mm OUTSIDE THE TANK, above oil level Minimum inlet pressure = 0,8 bar absolute B 800mm, = 200mm HORIZONTAL STALLATION A SIDE THE TANK SIDE THE TANK OUTSIDE THE TANK, above oil level OUTSIDE THE TANK, below oil level Minimum oil level equal or above the pump mounting surface. A 200mm Minimum oil level below the pump mounting surface. Minimum inlet pressure = 0,8 bar (absolute) B 800mm, = 200mm Minimum inlet pressure = 0,8 bar (absolute) B 800mm, = 200mm = 200mm : inlet line D: drain line A: minimum distance between inlet and drain line B+: permissible suction height : inlet line immersion dept
7 DIAGRAMS at 450 rpm (based on mineral oil ISO VG 46 at 50 ) 7. Noise level curves Ambient noise levels measured in compliance with ISO 442 oleohydraulics Test procedure to define the ambient noise level Pumps Shaft speed: 450 rpm. = Qmax = Qmin PVP*3029 PVP*4046 PVP*5073 and PVP*5090 7.2 Operating limits = Volumetric efficiency 4 = Power consumption with full flow 2 = Overall efficiency 5 = Power consumption at pressure compensation 3 = Flow versus pressure curve PVP*3029 PVP*4046 PVP*5073 Flow [l/min] Efficiency [%] 3 4 5 2 Power consumption [kw] Flow [l/min] Efficiency [%] Power consumption [kw] Flow [l/min] Efficiency [%] Power consumption [kw] Noise level [db] Noise level [db] Noise level [db] 4 3 5 2 3 5 4 2 7.3 Response times PVP*5090 7.3. Response times and pressure peack due to variation 0% 00% 0% of the pump displacement, obtained with an istantaneously opening and shutoff of the delivery line. Pump type T (ms) T2 (ms) PVP*3029 3 9 PVP*4046 44 20 PVP*5073 50 25 Swashing plate angle αmax αmin Flow [l/min] Efficiency [%] 3 4 5 2 Power consumption [kw] PVP*5090 53 28 Time [ms] 7.3.2 Variation of inlet pressure and reduction of displacement with increasing speed rating Speed rating [rpm/rpmmax] Inlet pressure [rbar abs.] Displacement rating [cm 3 /cm 3 max] A60
8 HYDRAULI AND ELETROHYDRAULI ONTROLS Hysteresis and pressure increasing; max 4 bar Manual pressure compensator The pump displacement decreases when the line pressure approaches the setting pressure of the compensator. The pump supplies only the fluid required by the system. Pressure may be steplessly adjusted at the pilot valve. ompensator setting range: 20 350 bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Flow [l/min] H Manual pressure compensator with venting As plus venting function, when a long unloading time is required and heat generation and noise have to be kept at lowest level. ompensator setting range: 20 350 bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Flow [l/min] Hysteresis and pressure increasing; max 4 bar R Remote pressure compensator As, but with remote setting of the compensator by means of a pressure relief valve on the piloting line X. This version can be obtained from version L using a blind plug UNI 5923 M4x2 in pos.l and a restrictor M4 drilled ø 0,75 mm in pos.. ompensator setting range: 20 350 bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Flow [l/min] Hysteresis and pressure increasing; max 4 bar not supplied L Load sensing The pump displacement is automatically adjusted to maintain a constant (load indipendent) pressure drop across an external throttle. hanging the throttle regulation, the pump flow is consequently adjusted. Load sensing control always incorporates an hydraulic compensator to limit the maximum pressure. ompensator setting range: 20 350 bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Differential pressure setting range: 0 40 bar Differential pressure standard setting: 4 bar Flow [l/min] Hysteresis and pressure increasing; max 4 bar not supplied LW onstant power In order to achieve a constant drive torque with varying operating pressure. The swashing angle and therefore the outlet flow is varied so that the product of flow and pressure remains constant. For the best regulation, minimum working pressure is 80 bar. While selecting LW control, the required value of power must be communicated with the order (ex. 0 kw at 450 rpm). Flow [% of max] Minimum power curve 300 Maximum power curve Theoretical power curve
9 DIMENSIONS OF PVP*3029: BASI VERSION ONTROL PORTS DIMENSION = Flange SAE 3000 /4 OUT = Flange SAE 6000 3/4 D, = /2 BSPP = Regulation screw for max displacement,5 cm 3 /rev per turn. Adjustable range 50% to 00% of max displacement. In case of double pump the regulation screw is not always available, please contact our technical office. LET PORT OUTLET PORT OUT DRA PORT DRA PORT Mass: 8 kg SHAFT TYPE SHAFT TYPE 5 SAE B SPLED 3 TEETH 6/32 PITH 30 VOLUTE SPLE TERMEDIATE FLANGE SAE A FOR PFE3 TERMEDIATE FLANGE SAE B FOR PFE4 SAE A SPLED 9 TEETH 6/32 PITH 00 Nm MAX SAE B SPLED 3 TEETH 6/32 PITH 35 Nm MAX OR2325 OR3400 Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted A60
0 DIMENSIONS OF PVP*4046: BASI VERSION ONTROL PORTS DIMENSION = Flange SAE 3000 /2 OUT = Flange SAE 6000 D, = /2 BSPP = Regulation screw for max displacement 2,2 cm 3 /rev per turn. Adjustable range 50% to 00% of max displacement. In case of double pump the regulation screw is not always available, please contact our technical office. LET PORT OUTLET PORT OUT DRA PORT DRA PORT Mass: 24 kg SHAFT TYPE SHAFT TYPE 5 SAE BB SPLED 5 TEETH 6/32 PITH 30 VOLUTE SPLE TERMEDIATE FLANGE SAE A FOR PFE3 TERMEDIATE FLANGE SAE B FOR PFE4 SAE A SPLED 9 TEETH 6/32 PITH 35 Nm MAX SAE B SPLED 3 TEETH 6/32 PITH 250 Nm MAX OR2325 OR3400 Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted
DIMENSIONS OF PVP*5073 and PVP*5090: BASI VERSION ONTROL LET PORT OUTLET PORT OUT DRA PORT PORTS DIMENSION = Flange SAE 3000 2 OUT = Flange SAE 6000 /4 D, = 3/4 BSPP = Regulation screw for max displacement 3,2 cm 3 /rev per turn. Adjustable range 50% to 00% of max displacement. In case of double pump the regulation screw is not always available, please contact our technical office. DRA PORT Mass: 33 kg SHAFT TYPE SHAFT TYPE 5 SAE SPLED 4 TEETH 2/24 PITH 30 VOLUTE SPLE TERMEDIATE FLANGE SAE A FOR PFE3 SAE A SPLED 9 TEETH 6/32 PITH 35 Nm MAX TERMEDIATE FLANGE SAE B FOR PFE4 SAE B SPLED 3 TEETH 6/32 PITH 330 Nm MAX OR2325 OR3400 TERMEDIATE FLANGE SAE FOR PFE5 SAE SPLED 4 TEETH 2/24 PITH 440 Nm MAX OR3400 Drawing show pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted A60
2 DIMENSIONS OF PVP: OTHER ONTROLS VERSION H VERSIONS L, R VERSION LW TIGHTENG TORQUE = 5 Nm max = Regulation screw for max displacement. Adjustable range 50% to 00% of max displacement). In case of double pump the regulation screw is not always available, please contact our technical office. Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted and also the consequently position of the control groups Pump type PVP*3029 PVP*4046 PVP*5073 PVP*5090 Version A B D E Mass (kg) H L R LW H L R LW H L R LW 68 44 44 77 53 53 90 66 66 00 09 22 2 235 258 04 20 22 9,2 20 28 25,2 26 36,9 34,2 35 0/0