Gege Mortise Door Locks
Main Door Lock Parts and Main Dimensions 2 Door lock - main parts Door lock - main dimensions 1 Forend 2 Lock case 3 Lock latch 4 Latch retaining spring 5 Lock hub 6 Follower spring 7 Lock bolt 8 Latch lever Retainer 10 Latch stop (for series 121.WZ and 127) 2 Forend length B Forend width C Forend thickness D Case height E Case width F Case thickness G Center distance H Backset K Distance to center Follower hole E H Rear backset Symbol legend Bit key Flat key WC- and Bathroom Latch configuration Eurorofile cylinder Europrofile cylinder with with latch lever Swiss Round cylinder
Direction determination Single leaf door inwards Door lock with latch lever Hinges Door furniture Lever handles hole part Lever handle pin part inside Knob Rigid handle Left inward (LI) Single leaf door outwards Door lock with latch lever Hinges Door furniture Lever handles hole part Lever handle pin part inside Knob Rigid handle Left outward (LO) 3 Single leaf door inwards Door lock with latch lever Hinges Door furniture Lever handles hole part Lever handle pin part inside Knob Rigid handle Right inward (RI) Single leaf door outwards Door lock with latch lever Hinges Door furniture Lever handles hole part Lever handle pin part inside Knob Rigid handle Right outward (RO)
Gege Door Lock Series 101 Silencio For inside doors up to 40 kg door weight Silencio mortise door lock with Delrin latch for exceptionally quiet door closing. The wear and UV resistant latch enables the latch to fall quietly into the striking plate Models ward key (KB), WC- and bathroom doors (WC), Euro profile cylinder without latch lever (PZ), latch lock (FA) Requirements and dimensions according to EN 1220, usage category 1, protection grade 1. latch is /changeable, single throw bolt (model PZ double throw). Case and cover are made of plate steel 1.2 mm thick ELO zinc plated Forend mm in decor (DS), (R) model. 4 101.KB 101.PZ T.4_101PZ.jpg Style Center distance Backset H Case width E Rear backset Flat key KB 0 50 80 30 WC WC 0 50 80 30 Europrofile cylinderwithout latch lever Europrofile cylinder without latch lever PZ 88 50 80 30 PZ 85 50 80 30 Latch lock FA --- 50 80 30 Europrofile cylinder without latch lever PZ 0 50 80 30 Forend Surface finish Hub Latch lever Fire protection 8,5 --- --- 8,5 --- --- 8,5 --- --- 8,5 --- --- 8,5 --- ---
Gege Door Lock Series 121 For inside doors up to 40 kg door weight Models bit key (BB), ward key (KB), WC- and bathroom doors (WC) Europrofile cylinder without latch lever (PZ), Europrofile cylinder with latch lever (WZ) Requirements and dimensions according to EN 1220 Models BB, KB, WC: Usage category 1, protection grade 1. Model PZ: Usage category 1, protection grade 1 Model WZ: Usage category 3, protection grade 2 Latch can be changed to /; for KB, BB, WC single throw bolt; for PZ, WZ double throw bolt Case and lid are made of plate steel 1.2 mm thick ELO zinc plated Forend in in decor (DS), (R) style or square (E) models. Model WZ: Fire resistance rating 30 minutes (T 30), with CE-marking according to EN 1220, Annex ZA 5 Forend square or 121.BB 121.WZ 121.WZ Style Center distance Backset H Case width E Rear backset Forend Surface finish Hub Latch lever Fire protection Bit key BB 0 50 80 30 /square --- --- Flat key KB 0 50,60,70 80,0,100 30 /square --- --- WC-Cylinder WC 0 50,60,70 80,0,100 30 /square --- --- Europrofile cylinder without latch lever PZ 88 50,60,70 80,0,100 30 /square --- --- Europrofile cylinder without latch lever PZ 85 50,60 80,0 30 /square --- --- Europrofile cylinder without latch lever PZ 0 50,60 80,0 30 /square --- --- Europrofile cylinder with latch lever WZ 88 50,60,70 80,0,100 30 /square Europrofile cylinder with latch lever WZ 85 50,60 80,0 30 /square Europrofile cylinder with latch lever WZ 0 50,60 80,0 30 /square Special models Forend: 230 x 18 x 3 mm 250 x 20 x 3 mm 250 x 22 x 3 mm
Gege DIN Door Lock Series 170 For inside up to 40 kg door weight - Center distance 72 mm (78 mm for WC model) Models bit key (BB), WC- and bathroom doors (WC), Euro profile cylinder without latch lever (PZ), Euro profile cylinder with latch lever (WZ) Requirements according to DIN 18251 Grade 2, BN1220 Latch with latch stop, / changeable Double throw lock, WC model single throw. Case and lid are made of plate steel 0.04 in thick ELO zinc plated Lock forend 235 x 18 x 3 mm or mm in decor (DS), (R) model. 6 170.BB 170.PZ 170BB Style Forend mm Center distance Backset H Case width E Rear backset Forend Surface finish Hub Latch lever Fire protection Bit key BB 72 55 85 30 WC WC 78 55 85 30 Europrofile cylinder Europrofile cylinder PZ 72 55 85 30 WZ 72 55 85 30 8,0 --- Forend 235 x 18 x 3 mm Bit key BB 72 55 85 30 WC WC 78 55 85 30 Europrofile cylinder Europrofile cylinder PZ 72 55 85 30 WZ 72 55 85 30 235 x 18 x 3 235 x 18 x 3 235 x 18 x 3 235 x 18 x 3 8,0 --- Special models Forend: 220x20x3 mm,, yellow zinc plated Forend: 235x24x3 mm, stainless steel, square Backset: 50,60 WC center distance: 72 mm in Latch lock: Latch lock with latch lever WZ: Fire retardant
Gege Door Lock Series 171 For main entrance doors in commercial buildings - Center distance 72 mm Europrofile with latch lever (WZ) and bathroom and WC doors (WC) models Requirements and dimensions according to DIN 18250 Grade 4. With spring entrapped follower, double throw bolt Case and lid are made of plate steel 0.04 in thick ELO zinc plated Forend mm in stainless steel (NR), (R) model.. 7 171.WZ.R65 171.WC.R65 T.12_171WZ.jpg Style Profile cylinder Profile cylinder Profile cylinder Profile cylinder Center distance Backset H Case width E Rear backset WZ 72 65 8 33 WZ 72 65 8 33 WZ 72 80 113 33 WZ 72 80 113 33 Forend Surface finish Stainless steel Stainless steel Stainless steel Stainless steel Hub Latch lever,0,0,0,0 Fire protection WC WC 78 65 8 33 WC WC 78 65 8 33 WC WC 78 80 113 33 WC WC 78 80 113 33 Stainless steel Stainless steel Stainless steel Stainless steel Special models Forend: 235 x 24 x 3 mm square/ Backset: 50, 55, 60 WC center distance: 72 mm
Gege Door Lock Series 10 For inside doors up to 40 kg door weight -center distance 0 mm Models ward key (KB), WC- and bathroom doors (WC), Euro profile cylinder without latch lever (PZ), Euro profile cylinder with latch lever(wz), ward key with latch lever (KBW) Requirements according to EN1220 Latch with latch stop, / changeable Double throw lock, WC model single throw. Case and lid are made of plate steel 0.04 in thick ELO zinc plated Forend 240 x 20 x 3 mm or 240 x 22 x 3 mm in decor (DS). 8 10.WC 10.PZ T.10_10PZ Style Center distance Backset H Case width E Rear backset Forend Surface finish Hub Latch lever Fire protection Flat key KB 0 45 71 26 /square 240 x 20 x 3 240 x 22 x 3 Flat keylatch lever KBW 0 45 71 26 WC-Cylinder WC 0 45 71 26 Europrofile cylinder without latch lever Europrofile cylinder with latch lever PZ 0 45 71 26 WZ 0 45 71 26 /square 240 x 20 x 3 240 x 22 x 3 /square 240 x 20 x 3 240 x 22 x 3 /square 240 x 20 x 3 240 x 22 x 3 /square 240 x 20 x 3 240 x 22 x 3 8,0 --- All dimensions are in mm
Gege Adjustable Striking Plates for inside rebated doors Your problem Environmental conditions can cause tension between the door leaf and door frame which can hinder smooth operation between the mortise door lock and the striking plate. Extensive adjustments on the door are often the consequence. Our solution This problem could be solved with the innovative Gege striking plates SB-VAR. The adjustable striking plates SB.VAR compensate changes and tension on the door leaf. An inlaid part which is attached to the striking base plate with a screw can be adjusted to four different wall thicknesses at the latch. The striking plate can be quickly and easily adjusted conveniently and direct on site at the door. By loosening the screw that holds the adjustment plate on the body, the striking plate can be turned horizontally and vertically to select the appropriate wall thickness. Note: Gege Striking Plate SB.VAR are best suited for use with Gege mortise door locks. The function is therefore only guaranteed when used with Gege mortise door locks series 121 and 101. Adjustment plate Base plate Fastening points 4 adjustable wall thick-
4 -Fold Adjustable Striking Plate SB.VAR For rebated inside doors up to 40 kg door weight Only available with single throw Gege door locks series 121 and 101. Not suitable for fire protection doors. For double throw locks --> break out the bottom of the base plate. Adjustments *) Dimensions 3 mm 3.5 mm 4 mm 5 mm Bolt and latch 210 x 20 x 10 *) Results from the wall thickness of the base plate (2 mm) + the wall thickness of the inlay part. Surface Finishes: yellow zinc plated (GV), stainless steel look (NL), polished solid brass (MP) Visible striking plate height 10 mm Additional door frame bolting with 2 semi- head screws is possible with striking plate SB.VAR. Mill drawing R6 Milling template Article No. 1163261 An MOF top milling head should be used with 30 mm spacing ring and 12 mm milling head 10 4 -fold adjustable Striking Plate SB.VAR.7 For rebated inside doors up to 40 kg door weight with single throw Gege door locks Adjustments *) Dimensions 3 mm 3.5 mm 4 mm 5 mm Bolt and latch 210 x 20 x 12 *) Results from the wall thickness of the base plate (2 mm) + the wall thickness of the inlay part. Surfaces: yellow zinc plated (GV), stainless steel look (NL) Radius: 1.5 mm, 3.5 mm, 5 mm Visible striking plate height 0.31 in Additional door frame bolting with 2 semi- head screws is possible with striking plate SB.VAR.7. Mill drawing Radius: 5 mm 3 mm 1.5 mm Milling template Article No. 1163475 An MOF top milling head should be used with 30 mm spacer ring and 14 mm milling head.
Gege Adjustable Striking Plates for rebated inside doors 4 -fold adjustable Striking Plate SB.VAR.ST For rebated inside doors up to 40 kg door weight with single throw Gege door locks For double throw locks --> break out the bottom of the base plate. Adjustments *) s Dimensions 13,2 mm 13.7 mm 14,2 mm 15.2 mm, bolt and latch, bolt and latch *) Results from the wall thickness of the base plate (2 mm) + the wall thickness of the inlay part. Surfaces: yellow zinc plated (GV), stainless steel look (NL): 210 x 20(30) x 16 Visible striking plate height mm in the latch area inside Left or is always determined as seen from the hinge side. Mill drawing Milling template Article No. 1163474 An MOF top milling head should be used with 30 mm spacer ring and 20 mm milling head. 11
Gege Striking Plates SB, angle 27 mm, bolt and latch, with camber Dimensions Square Bolt and latch 210 x 27 x 20 x 1.25 Surfaces: (DS), yellow zinc plated (GV) on request SB.R, angle 27 mm, bolt and latch, with camber Dimensions Radius mm Bolt and latch 210 x 27 x 20 x 1.25 Surfaces: (DS), yellow zinc plated (GV) on request 12 SB.S, angle 10 mm, bolt and latch, with camber Dimensions Square Bolt and latch 10 x 20 x 1.5 Surfaces: (DS), yellow zinc plated (GV) on request SB.SR.6, SB.SR., angle 10 mm, bolt and latch, with camber Dimensions Radius 6 mm Bolt and latch Radius mm Bolt and latch 210 x 10 x 20 x 1.5 210 x 10 x 20 x 1.5 Surfaces: (DS), yellow zinc plated (GV) on request
Gege Striking Plates SB.SR.U, U-form, angle 8 mm, bolt and latch, with camber Dimensions U-form Bolt and latch 10 x 20 x 8 Surfaces: (DS), yellow zinc plated (GV) on request U-form 8 mm with plastic inlay and off set screw, bolt and latch, with camber Dimensions U-form Bolt and latch 10 x 20 x 8 Surfaces: (DS), yellow zinc plated (GV) on request 13 U-form, 8 mm, bolt and latch, with camber Dimensions U-form Bolt and latch 185 x 27 x 8 Surfaces: (DS), yellow zinc plated (GV) on request
Gege Keys and Accessories Bit key for AUSTRIA Key nickel plated, available keyings 1, 2, 5, 6, 27, 28, 3, 40, 5, 60 Article Number Surface 1 2 5 6 27 28 3 40 5 60 BBSL.1 BBSL.2 BBSL.5 BBSL.6 BBSL.27 BBSL.28 BBSL.3 BBSL.40 BBSL.5 BBSL.60 Bit key nickel plated BBSL Flat key for AUSTRIA Key nickel plated, available keyings 110, 120, 230, 240, 350, 360, HS Article Number Surface KBSL.110 KBSL.120 KBSL.230 KBSL.240 KBSL.350 KBSL.360 Flat key nickel plated 14 KBSL.HS Flat key Master Key nickel plated KBSL KBSL.HS View and dimensions for Gege flat and bit keys View Direction View direction Flat Key Bit Key
Notes: 15
Authorized Dealer: Certified Management System ISO 001:Reg No. Q1530367 Technical changes reserved. Kaba GmbH Ulrich-Bremi-Strasse 2 A-3130 Herzogenburg Telephone +43 (0) 2782 808 0* Fax +43 (0) 2782 808 5505 www.kaba.com/cylinders-locks Gege is a registered brand of the Kaba Group Gege Mortise Door Locks, EN, 11/08