UNIVERSAL REMOTE CONTROL INSTRUCTION MANUAL One for All SetTopBox TV Home Theater
Universal Remote Control Key Map 2 1 4 3 6 5 10 14 16 19 8 12 15 18 7 9 11 13 17 23 21 22 20 24 25 26 29 27 28 30 31 1
No. Key Description STB Mode (or no TV/AUDIO programmed) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Menu Tools Next Previous Play/Pause Stop Power TV Forward Rewind REC List REC Back Guide Cursor Up OK Cursor Right Cursor Left Cursor Down VOD Vol +/ CH +/ Home Audio Numeric Keypad Subtitle Media Info TV/Radio Mute Color Function Keys Menu Tools Next Previous play/pause Stop Power Toggle Forward Rewind Rec List Record Back Guide Up OK Right Left Down VOD Vol+/or PT CH+/ TV/IRD Audio Numerics Subtitle Media Info TV/Radio Mute or PT Red Green Yellow Blue TV programmed only TV Power Toggle TV Source TV Vol+/ TV CH+/ TV>STB TV Mute TV/AUDIO Mode AUDIO programmed only TV+AUDIO programmed TV Power toggle AUX Power toggle TV Source TV Vol+ TV Mute TV Vol AUX Vol+/ AUX Vol+/ TV CH+/ TV>STB TV>STB AUX Mute AUX Mute AUX Source AUX Source AUX Power AUX Power 2
Universal Remote Control Programming for Etisalat Set Top Boxes The default Set Top Box protocol may be programmed in the field using the following procedure: Press the <Home> key, <REC> key and <OK> key simultanously for 3 sec, STB indicator LED will give a conformation blink and remain on. Release the keys and press a <Digit> key to select the Default Protocol. Refer to the table below for the protocol selection. The LED will blink, indicating that the Default STB Protocol has been programmed; the number of blinks corresponds to the Protocol number selected, i.e. 1 blink for Protocol 1, 2 blinks for Protocol 2, etc. Sr. No. SW Keys STB Model LED Confirmation 1 Digit2 Humax (evision logo) Two blinks 2 Digit4 Airties Four blinks 3 Digit5 Kaon (Etisalat logo) Five blinks 4 Digit6 Kaon (evision logo) Six blinks 5 Digit7 Huawei Seven blinks 6 Digit8 Pace Eight blinks 7 Digit9 Humax (Etisalat logo) Nine blinks 3
The Set top box protocol can be changed in the field to retune the RCU to another STB using the following procedure: Press and hold key Home and the relevant digit key together for a minimum of 3 seconds, until the STB indicator LED blinks two times (of 500 ms each). The new STB protocol is now programmed to nonvolatile memory. Power on the STB and try out the dedicated STB buttons. If there is no reaction on the STB, repeat the previous steps, for each code listed below. Protocol Keys STB protocol number 1 Home + Digit2 Humax (evision logo) 2 Home + Digit4 Airties 3 Home + Digit5 Kaon (Etisalat logo) 4 Home + Digit6 Kaon (evision logo) 5 Home + Digit 7 Huawei 6 Home + Digit 8 Pace 7 Home + Digit 9 Humax (Etisalat logo) 4
Quick Start Guide to set up the remote of your TV * 1. Switch on your TV 2. Press and hold the TV button on your remote for 5 seconds. The TV button will light up. 3. Look up the 4digit code for your brand in the adjacent shortlist of brands. (Look at page no. 6) Enter the 4digit codes using the digit buttons. 4. Press and hold the Power button. Release the button immediately as soon as the TV switches off. (This step normally takes between 5 and 60 seconds). 5. Switch On your TV. Try out the volume channel buttons on your remote. If those buttons are not working on your remote control, repeat step4. until some button works. Note: You can also learn the butttons from your original remote. See next pages for details. 6. Press the TV button twice (2x) to finish setup Important: If you made a mistake: Press the TV button twice to exit setup. The red light under the TV button turns off. Restart from the beginning 5
Shortlist of brands* Brands Name Bang & Olufsen BenQ Blue Sky Bush Carrefour Daewoo Firstline Funai Grundig Hitachi Insignia JVC Lg Loewe Metz Mivar Nokia Panasonic Philips Pioneer RCA Samsung Sanyo Sharp Sony Toshiba Vizio Brand Number 0314 0359 0395 0445 0492 0692 1008 1056 1162 1251 1368 1464 1628 1660 1810 1857 2017 2153 2195 2212 2351 2448 2462 2550 2679 3021 3211 If your brand is missing in this shortlist, look at the complete BRAND LIST at the end of the user manual Use '9999' as 4digit code in case you cannot find your brand in the BRAND LIST int the user manual. Note that 9999 may result in a long setup (up to 15 minutes) * For the full list of TV brands, visit www.etisalat.ae/elife 6
Turn on the TV/Audio Press and hold the <<TV>> key for 3 seconds; until the setup LED lights up. This enables the protocol and brand selection function for the TV device, the mode LED will remain on. To enable selection for AUX device, press <Mute> key after hold <<TV>> key for 3 secs, the TVmode led will give a Setup Confirmation blink. Release the key and enter the 4digit Brandid (please refer to brand ID table guide) for the TV/AUX by pressing each digit key in sequence. With the first 3 digits, the deviceled will give a reverse blink. At the fourth digit, the device LED gives two reverse blinks and remains on (the search will include all code sets that are linked to the selected brand, or it will search through all code sets in the universal database if brand number 0000 was selected). Press the <<POWER>> or <<MUTE>> key continuously; after 5 secs a power or mute IRcommand is transmitted for the next universal codeset in the codeset list for the selected brand. The deviceled will turn off durin tranmission of the IRcommand. When the <<POWER>> or <<MUTE>> key is held continuously then subsequent universal codesets will be selected automatically and a sequence of standby or mute IRcommand of the next universal codeset is transmitted. In the case that brand number 0000 was selected the whole database of either TV or Aux is scanned. The deviceled shows a reverse blink for each transmission. 7
Press TV twice to confirm the code. The code that was selected when TV was pressed twice or when 4 sec timeout happened is the code that will be programmed into the remote. The RC will give a setup confirmation blink and go back to normal operation. All LEDs are turned off. Remarks. Universal code number 0000 will trigger a search through all codes available in the remote independent of the brand. Timeout for 4 seconds happened if the user hasn t pressed the TV key twice to confirm the code. The code will be programmed into the remote; the RC will give a setup confirmation blink and go back to normal operation. During the setup, if user wants to restart TV device setup, can press and holding the <<TV>>key for 3 sec (step ii);if user want to restart AUX device, can press <Mute> after holding the <<TV>>key for 3 sec, then the setup start from the beginning of the auto setup again (step iii). * For the full list of Audio devices programming codes, visit www.etisalat.ae/elife 8
In the case that brand number 0000 was selected the whole database of either TV or Aux is scanned. The deviceled shows a reverse blink for each transmission. Note that the search sequence continues by going through the whole list after scanning through the brand list when all codesets for the brand are tested. It only stops when all codesets of the whole database are tested. When the TV/AUX turns off or mute, the user must release the POWER or MUTE key. The user should switch the TV/AUX on again with the original or the universal remote control it device turn off. Now all keys can be tried out with the universal remote control (inverse blinking if a universal functioncode is available under the key) including the POWER and MUTE key. Press <<POWER>> or <<MUTE>> for 5 secs to continue the codeset selection (item iv, above). If the 4 digit code is wrong or if another key than the <<POWER>> or <<MUTE>> key is pressed after the 4 digits, Auto brand search will be exited and the unit will not change the universal codeset number for the respective device. Exiting a successful setup is via pressing the TV mode key twice or after timeout. 9
After TV/Aux is also setup in addition to Etisalat STB setup with the remote, the remote control will control the volume of the TV/Aux only and the STB volume control will not be managed from the remote any more. In case one prefers however to continue to control the volume via the STB and want the volume control to work for TV/Aux when selecting TV (pressing TV) and volume control to work for STB when selecting STB (pressing Home), the following need to be performed once. Press Home and Mute simultaneously for 5 seconds until the light under the TV keys blinks twice. With the above steps you can toggle between TV/Aux and STB and there will be volume control for TV while in TV mode and Volume control for STB when in STB/Home mode. 10
For more information, please call 101 or visit www.etisalat.ae/elife