Fuel Storage & Control Systems Generator Packaging & Enclosures Options Include: Double-Walled & Fire Rated Tanks, Hurricane Rated & Sound Attenuated Enclosures phoenixproducts 1727 Bennett Street, Jacksonville, FL 32206 904-354-1858 904-354-7929 Fax phoenix.sales@phoenixprods.com www.phoenixprods.com
fueltanks Aboveground & Sub Base Tanks Envirovault & Fire-Steel UL2085 Protected Aboveground Tanks True double-wall construction with lightweight concrete filled interstitial space UL 2085 listed and labeled Protected aboveground tank for flammable and combustible liquids Fire, vehicle impact and ballistic rated Meets requirements for secondary containment, leak monitoring, spill containment, and overfill protection Inner and outer tanks constructed per UL 142 Steel aboveground tanks for flammable and combustible liquids Six inches of lightweight concrete protection between inner and outer tanks provides minimum two-hour fire rating High-build polyester epoxy glassflake impregnated coating used for salt water submersion protection on offshore platforms, 20,000 hour ASTM B117 salt spray tested Primary and emergency vents standard All fittings and protrusions are stainless steel Steel support channel allow visual tank bottom inspection and air circulation Designed to meet or exceed national, state and local codes No exposed concrete Exceeds liability insurance requirements Engineered for seismic IBC standards Integral earthquake and hurricane tie downs Leak detection space provided Meets NFPA 30 and 30A Options Stairs and platforms (aluminum/galvanized steel) meeting OSHA standards with handrails Stainless steel inner and outer tanks Fuel heaters Stainless steel inner and outer tanks Multiple internal compartments Stainless steel accessory equipment boxes and top/remote fill boxes Fuel monitoring and control systems Tank top hand rails approved by OSHA Day tanks with supply and return pumps Custom color matching Fuel polishing systems Dispensing equipment
PowerTank & Double-Wall UL142 Secondary Containment Tanks Steel aboveground tanks for flammable and combustible liquids UL 142 listed and labeled protected aboveground tank for flammable and combustible Meets requirements for secondary containment, leak monitoring, spill containment, and overfill protection No external cross beams or side supports to interfere with generator placement or stairs and walkways Supports generator sets up to 80,000 pounds, with or without enclosures Primary and emergency vents standard Rounded corners allowing proper adherence of industrial grade enamel coating Steel support channel allow visual tank bottom inspection and air circulation Designed to meet or exceed national, state and local codes NFPA 30, 30A, 37 & 110 True double-wall construction for UL certification Exceeds liability insurance requirements Engineered for seismic rating Earthquake and hurricane tie downs Leak detection space provided Options Stairs and platforms (aluminum/galvanized steel) meeting OSHA standards with handrails Fuel heaters Stainless steel fittings, protrusions and fill boxes Stainless steel inner and outer tanks Custom color matching Over-fill spill protection Fuel polishing systems Dispensing equipment Fuel monitoring and control systems Day tanks with supply and return pumps Tank top hand rails approved by OSHA Manway access Remote fill
generatorenclosures Genset Enclosures Weather Proof, Sound Attenuated, High Velocity-Hurricane Zone & Agency for Health Care Administration Fully weather, corrosion and wind load resistant all aluminum enclosure Interlocking aluminum panels, make a lightweight and corrosion resistant housing Standing seam sloped roof, mill-finish aluminum Fixed intake louvers with expanded aluminum and gravity dampers on discharge provide water intrusion prevention Weather-proof gasket and stainless steel hardware on 36-inch doors with padlocking handles Reinforced door and roof structure Wind load rating 150 MPH Optional 200 MPH ALL ALUMINUM, CORROSION, WEATHER, WIND & MISSILE-IMPACT RESISTANT ENCLOSURES Optional Certifications Miami-Dade County Notice of Acceptance Department of Business and Professional Regulations Florida Building Code SUPERIOR STRUCTURAL DESIGN & MISSILE IMPACT PROTECTION
Enclosure Options Motorized air intake and discharge dampers Stainless steel hold-downs Sound attenuation Three point door latches with padlocking handles Reinforcements at all corners and openings 200 MPH wind load construction PE signed & sealed drawings Interior silencer Interior AC and DC lights with timer switch Exterior emergency stop station Electrical and lighting systems Custom paint matching AHCA Compliance High Velocity Hurricane Zone Rating PROTECTIVE ENCLOSURES FOR ALL GENERATOR SIZES
moreproducts Falcon Enclosures & Tanks High quality, economical Fuel Storage and Enclosures for Generators 300kW and Lower UL 142 Listed, FDEP Compliant both inner and outer tanks are completely sealed and pressure tested Meets requirements for secondary containment, leak monitoring, spill containment, and overfill protection Supports generators up to 300KW Accommodates Phoenix Products and factory generator enclosures, both weather-proof and sound attenuated Fill cap, primary vents and emergency vents package standard Steel 2-inch channel supports, allow visual inspection of tank bottom as well as air movement to prevent condensation induced corrosion Black satin industrial grade enamel paint Spill containment with spring-loaded drain valve Leak sensor probe Low and high fuel level floats Interlocking aluminum panels, make a lightweight and corrosion resistant housing Standing seam sloped roof, mill-finish aluminum Fixed intake louvers with expanded aluminum and gravity dampers on discharge provide water intrusion prevention Weather-proof gasket and stainless steel hardware on 36-inch doors with padlocking handles Reinforced door and roof structure Wind load rating 120 MPH; Optional 150 MPH Diesel Director Day Tanks UL 142 double wall secondary containment tanks Optional UL 2085 interstitial concrete filled double wall tanks with 2-hour fire rating Supply & return pumps Control panel with high and low level alarms Leak sensor Emergency and Primary vents Gauge stick Float fuel level Mechanical leak sensor Spare fittings ports Tank drains with ball valve Lockable fill cap Phoenix Products coating system Optional OSHPD certification Diesel Director Remote Fillport Ground level connection to fuel truck fill hose Single or multiple tanks Spill containment Optional control panel and 2, 3 or 4 inch fill pipe sizes with or without booster pumps Lockable, weatherproof stainless steel enclosure Hand pump discharge Two-point alarm for high and leak indication Optional control panel with tank selector, automatic ball valves, digital capacity display Optional stainless steel base stand Additional ball valves UL listed Optional flanged automatic valves Optional fusible link fire valves Optional high capacity pump and motor for fuel transfer from gravity trucks
aboutus About Phoenix Products Based in Jacksonville, Florida, Phoenix Products was established in 1991 as a fuel tank supplier. Our heritage differentiates us from other generator packagers because of our expertise in fueling systems. In fact, we pioneered several innovative fueling alternatives, now widely used and required by many regulatory agencies. For example, our patented Fire-Steel Generator Base Tank, which was the first UL2085 listed base tank, is now a regulatory requirement in many jurisdictions. Also, our Pipe Daytank System allows placement of emergency power systems in locations where it once was impractical or simply not allowed. We understand that fueling systems are an integral part of any Emergency Power System design; not an afterthought. Built to Last Phoenix Products is a pioneer in the use of aluminum structures for enclosure design. Most competitive generator packages are built with steel housings. Our interlocking panel design provides the corrosion resistance of aluminum, yet provides the structural integrity of up to a 200 MPH wind rating, and sound attenuation options up to 45 dba reduction. One Call Does It All With more than 20 years of experience and customers in a variety of environments, we are familiar with virtually every possible requirement or expectation. Our fabrication technicians are highly trained, extremely talented and willing to take on challenging builds. So if you have a special need or custom request, just ask. Phoenix Products is committed to providing superior product design, exceptional quality, timely delivery and competitive pricing. 1727 Bennett Street, Jacksonville, FL 32206 904-354-1858 904-354-7929 Fax phoenix.sales@phoenixprods.com www.phoenixprods.com
phoenixproducts 1727 Bennett Street, Jacksonville, FL 32206 904-354-1858 904-354-7929 Fax phoenix.sales@phoenixprods.com www.phoenixprods.com