Specification Data CH30004 02/98 Control Valves A Complete ine of Heavy Duty, Balanced, Cage Guided, Globe Valves with Noise Control o-db Trim
Table of Contents Foreword... 2 Numbering System... 3 Ratings/Connections... 3 General Data... 4 Allowable Pressure Drop Page Index... 4 Temperature Range/Seat eakage... 5 C V and F versus Travel... 5-8 Construction... 9 Materials... - 13 Allowable Pressure Drops... 14-27 Dimensions... 28-31 Weights... 32 Accessories and Options... 33 Sales Offices and Distribution Centers... 3 Foreword Masoneilan s heavy-duty control valve line, engineered to handle the most demanding process conditions, exceeds the capabilities of regular valves. Broad Temperature Ranges for size, the provides effective control throughout a broad range of process temperatures from -19 C to +5 C. Higher Allowable Pressure Drops control valves provide exceptional and dependable performance over a wide range of pressure drops typical of severe services. Greater Capacity with ow Recovery Masoneilan s control valves have the highest capacities of contemporary cage-type globe valves. These unusually high capacities are attained with minimum pressure recovery, as indicated by high critical flow (F ) factors. High-Performance Materials are Standard Without exception, the materials we specify as standard on the have been tested and selected to provide trouble-free operation in services with high pressures and extreme temperatures. Therefore, specification is simplified and longevity on any application is assured. Variety of High Performance ngineered Trim Packages Available with full area as well as reduced C V capacities, trim options include : o-db Single Stage trim - provides excellent noise attenuation on gas and steam services and cavitation protection on liquid services. o-db Double Stage trim - designed for noise control on gas or steam at high pressure drop ratios. For more information regarding NAC conformance, cavitation, critical pressure drop, and VRT trim, consult your Masoneilan representative or refer to the following publications : 1. Masoneilan Handbook for Control Valve Sizing (Bulletin OZ00) 2. Masoneilan Noise Control Manual (Bulletin OZ3000) Trade names noted throughout are for reference only. Masoneilan reserves the right to supply trade named material or its equivalent. 2
Numbering System 1st 2nd 1st 2nd 3rd 4th 5th 4 1 Type Body Series Seal Type Control Characteristic Trim Type 37 Spring Diaphragm : direct, air to close (fail open action) 38 Spring Diaphragm : reverse, air to open (fail closed action) 87 Spring Diaphragm : direct, air to close (fail open action) 88 Spring Diaphragm : reverse, air to open (fail closed action) 41 Cage Guided Globe O. Undefined 3. Pressure nergized PTF Seal Ring 4. Auxiliary Shutoff Plug 5. Metal Seal Ring. PTF Seal Ring 9. Graphite Seal Ring 0. Undefined 1. inear 2. qual % 0. Undefined 1. Standard 2. o-db Single Stage 3. o-db Single Stage with Diffuser 4. o-db Double Stage Ratings/Connections Threaded Socket Weld Butt Weld RF & RTJ mm Valve inch 50 2 80 to 200 3 to 8 250 to 400 to ANSI Class 150 to and equivalent PN ANSI Class 2500 and equivalent PN 80x50x80 0x50x0 0x80x0 3x2x3 4x2x4 4x3x4 to to 400x300x400 x12x Note : For AFNOR and DIN connections, consult Masoneilan 3
General Data Standard Valve (41300, 41400, 4, 400 and 41) Body type : high-capacity globe flow direction : see Allowable Pressure Drop Table o-db trim : flow to open for gas or steam o-db trim with diffuser : flow to close for gas or steam cavitation service : flow to close C V ratio : 0:1 standard capacity trim 50:1 o-db and reduced capacity trim Bonnet type : stud bolted, extended Trim cage : cylindrical ported or o-db plug : pressure balanced cage guided with metal, PTF, or graphite seal ring ; pressure balanced cage guided, with spring loaded internal auxiliary tight shutoff plug Flow Characteristic standard trim : linear, equal percentage o-db Double Stage Valve (41314) flow direction : flow to open gas or steam only C V ratio : 50:1 Trim cage : two-stage o-db plug : Flow Characteristic standard trim : type : handwheel : pressure balanced cage guided with pressure energized PTF seal ring linear spring diaphragm, optional Allowable Pressure Drop Page Index Model F.T.C./Page F.T.O./Page Model F.T.C./Page F.T.O./Page 41311-20, 21, 22, 41312-20, 21, 22, 41321-20, 21, 22, 41314 -, 25 411 17, 2, 27 421 17, 2, 27 412 19 2, 27 413 19 2, 27 41411 14, 15-41421 14, 15-41412 - 41413-41511 17, 2, 27 41521 17, 2, 27 41512 19 2, 27 41513 19 2, 27 41911 17, 2, 27 41921 17, 2, 27 41912 19 2, 27 41913 19 2, 27 4
Temperature Range/Seat eakage Seat eakage per Valve Temperature Range ( C) Model IC 534-4 and Type mm inch Minimum Maximum ANSI / FCI 70.2 Class 41300 50-400 2 - -4 + 2 IV & V Standard IV 41400 50-400 2 - -19 + 5 Single Stage V (optional) o-db 50-0 2-4 -19 + 5 II Anti-Cavitation 4 150-400 - -19 + 5 III 400 50-400 2 - -29 + 149 IV 41 50-0 2-4 -19 + 5 III 150-400 - -19 + 5 IV o-db Double Stage 41314 50-400 2 - -4 + 2 IV & V C v and F versus Travel Standard Trim (Single Stage) Models 41411, 41511, 411 and 41911 Flow Characteristic : INAR Percent of Travel 20 30 40 50 0 70 80 90 0 F 0.94 0.94 0.93 0.93 0.92 0.92 0.91 0.91 0.90 0.90 Valve ANSI Class Orifice Travel and Diameter mm inch equivalent PN (mm) (mm) Rated C V 50 2-2500 4.7 20.3 1.4 2.7 4.2 8 12.5 14 15.5 2 4.9 8.3 13 19 25 30 35 38 40 50 2 300, 2.7 5.1 7.9 11 15 19 2 29 30 3.5 38.1 80 3 2500 4 8 14 22 34 4 5 5 72 75 80 3 300-5.4 30 38 45 51 59 0 88.9 50.8 0 4 2500 8 17 28 4 70 95 115 134 148 155 0 4 300-9 25 3 47 0 71 81 93 95 111.3 50.8 150 2500 12 32 55 8 122 15 4 208 22 0 150 150-20.3 2 42 58 74 93 119 142 5 130.0 200 8 2500 50.8 20 54 90 145 205 20 305 345 375 400 200 8 150-5.1 38.1 15 40 75 1 145 190 250 3 35 415 3.5 30 85 145 5 330 415 495 550 40 250 150-203.2 38.1 20 50 80 130 0 0 290 370 440 5 7.2 50 130 0 370 5 50 770 80 940 00 300 12 150-7.7 50.8 30 70 140 200 270 350 450 570 80 770 95.25 70 0 320 520 7 9 80 1200 1320 1400 400 150-330.2 3.5 30 130 0 298 4 548 730 50 1280 1. 0 20 40 740 20 1300 1540 1720 80 2000 5
Cv and F versus Travel Standard Trim (Single Stage) Models 41421, 41521, 421 and 41921 Flow Characteristic : QUA PRCNTAG Percent of Travel 20 30 40 50 0 70 80 90 0 F 0.94 0.94 0.94 0.94 0.94 0.94 0.93 0.92 0.92 0.90 Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V 50 2-2500 4.7 20.3 0.5 0.7 1 1.5 2.7 5 7.9.5 12. 14 0.7 1.3 2.2 3.. 12. 19.8 2.4 31.5 35 50 2 300, 0.9 1.3 1.8 2.9 4.9 9.4 14.7 19..4 2 3.5 38.1 80 3 2500 1.2 2.3 4.2.8 12.3.4 3.7 49 58.5 5 80 3 300-2 2.8 3.9.2. 20.1 31.2 42.2 50.4 5 88.9 50.8 0 4 2500 3 5 9 15 2 50 79 5 12 140 0 4 300-3 5 17 32 51 8 81 90 111.3 50.8 150 2500 4 8 14 43 81 127 170 203 225 150 150-5 7 27 52 81 8 130 144 130.0 50.8 200 8 2500 7 13 37 8 130 203 271 3 30 200 8 150-5.1 3.5 8 12 25 43 83 130 174 207 0 11 21 37 0 9 207 3 433 5 575 250 150-203.2 7.2 17 32 58 94 170 3 508 78 8 300 12 150-7.7 95.25 45 81 131 8 454 711 949 1134 120 41300 Series (Single Stage) Model 41311 Flow Characteristic : INAR Percent of Travel 20 30 40 50 0 70 80 90 0 F 0.94 0.94 0.93 0.93 0.92 0.92 0.91 0.91 0.90 0.90 Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V 50 2-4.7 20.3 1.4 2.7 4.2 8 12.5 14 15.5 2 4.9 8.3 13 19 25 30 35 38 40 50 2 3.5 38.1 2.7 5.1 7.9 11 15 19 2 29 30 4 8 14 22 34 4 5 5 72 75 80 3-88.9 50.8 5.4 30 38 45 51 59 0 8 17 28 4 70 95 115 134 148 155 0 4-111.3 50.8 9 25 3 47 0 71 81 93 95 12 32 55 8 122 15 4 208 22 0 150-130.0 50.8 20 52 92 144 204 20 308 344 37 400 200 8-5.1 3.5 32 83 147 0 32 4 493 550 02 40 250-203.2 7.2 50 130 0 30 5 50 770 80 940 00 300 12-7.7 95.3 70 2 322 504 714 9 78 1204 13 1400 400 300, 330.2 1. 0 20 40 740 20 1300 1540 1720 80 2000
Cv and F versus Travel 41300 Series (Single Stage) Model 41321 Flow Characteristic : QUA PRCNTAG Percent of Travel 20 30 40 50 0 70 80 90 0 F 0.94 0.94 0.94 0.94 0.94 0.94 0.93 0.92 0.92 0.90 Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V 50 2-4.7 20.3 0.7 1.3 2.2 3.. 12. 19.8 2.4 31.5 35 50 2 3.5 38.1 1.2 2.3 4.2.8 12.3.4 3.7 49 58.5 5 80 3-88.9 50.8 3 5 9 15 2 50 79 5 12 140 0 4-111.3 50.8 4 8 14 43 81 127 170 203 225 150-130.0 50.8 7 13 37 8 130 202 272 3 30 200 8-5.1 3.5 12 21 3 59 9 207 322 434 5 575 250-203.2 7.2 32 57 93 171 3 504 80 8 300 12-7.7 95.3 25 45 79 130 9 454 70 951 1134 120 o-db /Anti-cavitation (Single Stage) Model 41312 Flow Characteristic : INAR Percent of Travel 20 30 40 50 0 70 80 90 0 F 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 Valve ANSI Class Orifice and Diameter Travel Rated C V mm inch equivalent PN (mm) (mm) 50 2-4.7 20.3 50 2 3.5 38.1 80 3-88.9 50.8 0 4-111.3 50.8 150-130.0 3.5 200 8-5.1 7.2 250-203.2 88.9 300 12, 7.7 1. 400 330.2 1. 1.2 2.4 3. 4.8.0 7.2 8.4 9..8 12 2.5 5 7.5 12.5 15 17.5 20 22.5 25 3 9 12 15 21 27 30 2.5 5 7.5 12.5 15 17.5 20 22.5 25 5 15 20 25 30 35 40 45 50 7 13 20 2 33 39 4 52 59 5 5 9 14 27 32 3 41 45 19 29 38 48 57 7 7 8 95 12 3 48 0 72 84 9 8 120 7 14 21 28 35 42 49 5 3 70 15 29 44 58 73 87 2 1 131 145 20 40 0 80 0 115 135 155 175 195 11 21 32 42 53 3 74 84 95 5 21 42 3 84 5 12 147 8 9 2 30 0 90 120 150 0 2 0 270 300 35 3 95 12 158 9 221 252 284 315 50 0 150 200 250 300 350 400 450 500 73 145 2 290 33 435 508 580 53 725 120 0 30 480 720 840 90 80 1200 7
C v and F versus Travel o-db/anti-cavitation (Single Stage) Models ➀ 41412 41512 412 41912 41413 41513 413 41913 Flow Characteristic : INAR Percent of Travel 20 30 40 50 0 70 80 90 0 F 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 0.94 Valve ANSI Class Orifice and Diameter Travel mm inch equivalent PN (mm) (mm) Rated C V 50 2-2500 4.7 20.3 50 2 300, 80 3 2500 80 3 300-0 4 2500 0 4 300-150 2500 150 150-200 8 2500 3.5 38,1 88.9 50,8 111.3 50,8 130.0 3,5 200 8 150-5.1 7.2 250 150-203.2 88.9 300 12 150-7.7 1. 400 150-330.2 1. ➀ Where diffuser is added on high capacity trim, overall C V is reduced as much as 15%. 1.2 2.4 3. 4.8.0 7.2 8.4 9..8 12 2.5 5 7.5 12.5 15 17.5 20 22.5 25 3 9 12 15 21 27 30 2.5 5 7.5 12.5 15 17.5 20 22.5 25 5 15 20 25 30 35 40 45 50 7 13 20 2 33 39 4 52 59 5 5 9 14 27 32 3 41 45 19 29 38 48 57 7 7 8 95 12 3 48 0 72 84 9 8 120 7 14 21 28 35 42 49 5 3 70 15 29 44 58 73 87 2 1 131 145 20 40 0 80 0 115 135 155 175 195 11 21 32 42 53 3 74 84 95 5 21 42 3 84 5 12 147 8 9 2 30 0 90 120 150 0 2 0 270 300 31 47 2 78 93 9 1 140 155 32 3 95 12 15 9 221 252 284 315 50 0 150 200 250 300 350 400 450 500 25 50 75 0 125 150 175 200 225 250 50 0 150 200 250 300 350 400 450 500 5 130 195 20 325 390 455 520 585 50 70 145 215 290 30 435 505 580 50 725 120 0 30 480 720 840 90 80 1200 o-db (Double Stage) Model 41314 Flow Direction : FOW TO OPN Flow Characteristic : INAR Percent of Travel 20 30 40 50 0 70 80 90 0 F 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 0.95 Valve ANSI Class Nominal and Orifice Travel Diameter mm inch equivalent PN (mm) (mm) Rated C V 50 2-4.7 38.1 3.5 7 11 14 21 25 28 32 35 80 3-88.9 50.8.5 13 20 2 33 39 4 52 59 5 0 4-111.3 3.5 13 25 38 50 3 75 88 0 113 125 150-130.0 3.5 15 30 45 0 75 90 5 120 135 150 200 8-5.1 7.2 30 0 90 120 150 0 190 220 250 300 250-203.2 1. 41 82 1 4 205 287 328 39 4 300 12, 7.7 1. 0 120 0 0 300 30 420 480 540 400 330.2 1. 80 0 0 320 400 480 50 40 720 800 8
Body S/A Construction 1 2 3 22 21 4 5 7 8 9 11 13 14 15 Balance Plug Construction 4, 400, 41 Series DN 50 to DN 400 (2" to ") (DN 50 to DN 0 Shown) 19 20 17 12 12 Pilot Balanced Construction 41400 Series DN 50 to DN 0 (2" to 4") Pilot Balanced Construction 41400 Series DN 150 to DN 400 (" to ") 9
Materials Carbon and ow Alloy Steel Version Ref. No Temperature Range Description -29 C +343 C +427 C +454 C +5 C Standard Materials 1 Valve plug stem Martensitic St. St. Type 17-4 PH ASTM A 38 Gr 0 2 Packing flange stud Austenitic St. St. Type 304 3 Packing flange nut Austenitic St. St. Type 304 4 Packing flange Carbon steel zinc plated 5 Packing spacer Austenitic St. St. Type 303 Packing KVAR + PTF GRAPHIT 7 Bonnet CARBON ST ASTM A 2 Gr WCC Body CHROM-MOYBDNUM ST ASTM A 217 Gr WC 8 Valve body nut ASTM A 194 Gr 2H ASTM A 194 Gr 4 9 Plug pin Austenitic Stainless Steel Valve body gasket Spiral wound 3 St. St. with graphite filler 11 Seal ring type See page 12 12 Plug spring (41400 only) INCON X750 13 14 15 17 19 Seat ring Austenitic St. St. Type 3 with hardfacing Seat ring gasket Valve plug Spiral wound 3 St. St. with graphite filler Martensitic St. St. Type 17-4 PH Cage Martensitic St. St. Type CANM Chromium-plated Flat spring ( " to ") Martensitic St. St. Type 17-4 PH Retaining ring (41400 only) INCON X750 (2 to 4") St. St. Type 3 w. hardfacing (" to ") St St type CA NM w. hardfacing Martensitic St. St. Type CANM Nitrited Martensitic St. St. Type CANM Nitrited INCON X750 + shot peening 20 Auxiliary plug (41400 only) (2" to 4") Martensitic St. St Type 4 ( to " ) Martensitic St. St. Type CANM with hardfaced and chromium-plated Martensitic St. St. Type CANM with hardfaced and chromium-plated 21 Valve body stud ASTM A 193 Gr B7 ASTM A 193 Gr 22 Guide bushing Martensitic St. St. Type 440 C Packing follower Austenitic St. St. Type 303
Materials Stainless Steel Version Temperature Range Ref. No Description -19 C -1 C -4 C -29 C +149 C +343 C +427 C +454 C +5 C Standard Materials 1 2 3 4 5 Valve plug stem Packing flange stud Packing flange nut Packing flange Packing spacer Packing ASTM A 38 Gr 0 Martensitic St. St. Type 17-4 PH Austenitic St. St. Type 304 Austenitic St. St. Type 304 Stainless Steel Austenitic St. St. Type 303 KVAR + PTF ASTM A 38 Gr 0 GRAPHIT 7 Bonnet Body AUSTNITIC STAINSS ST TYP 3 8 Valve body nut ASTM A 194 Gr 8M ASTM A 194 Gr 4 ASTM A 194 Gr 2H ASTM A 194 Gr 4 9 11 Plug pin Valve body gasket Seal ring type 3 Stainless Steel Spiral wound 3 St. St. with graphite filler See page 12 12 Plug spring (41400 only) INCON X750 (2 to 4") St. St. Type 3 13 Seat ring Austenitic St. St. Type 3 with hardfacing with hardfacing (" to ") St. St. Type CANM with hardfacing 14 15 17 19 20 Seat ring gasket Spiral wound 3 St. St. with graphite filler Valve plug Martensitic St. St. Type 17-4 PH Cage Martensitic St. St. Type CANM Chrome-plated Consult Masoneilan Consult Masoneilan Flat spring ( " to ") INCON X750 +shot peening Martensitic St. St. Type 17-4 PH INCON X750 + shot peening Retaining ring INCON X750 (41400 only) (2" to 4") Martensitic St. St. Type 4 Auxiliary plug Martensitic St. St. Type CANM Martensitic St. St. Type CANM (" to ") Martensitic St. St. Ty. CANM (41400 only) with hardfaced and chromium-plated with hardfaced and chrome-plated w. hardfaced & chromium-plated 21 Valve body stud ASTM A 193 Gr 8M ASTM A 320 Gr 7 ASTM A 193 Gr B7 ASTM A 193 Gr 22 Guide bushing Austenitic St. St. Ty. 3 w. hardfacing Martensitic St. St. Type 440 C Packing follower Austenitic St. St. Type 303 11
Seal Ring Construction 41300 Series has a Pressure nergized Polymeric Seal Ring. 41400 and 4 Series has a Metal Seal Ring. eakage Class Ranging from Class II to Class V are obtainable with temperatures ranging from -19 C to +5 C. PUG CAG 3 35 31 PUG CAG 400 Series has a TF Seal Ring and a Resilient Inner Ring. eakage Class IV is standard with temperatures ranging from -29 C to +149 C. 41 has a Graphite Seal Ring and Metal Inner Ring. eakage Class IV is standard with temperatures ranging from -19 C to +5 C for " to " and Class III for 2" to 4". 41 40 4 45 PUG CAG PUG CAG DN 50 - DN 400 (2" - ") Materials of Construction Temperature Range -19 C -4 C -29 C +149 C +2 C +343 C +5 C Ref. No. Description Materials 31 Seal Ring PTF + 25% graphite and GIOY spring 35 xternal Seal Ring Ni-Resist ASTM A439 Type D3 3 Internal Seal Ring Ni-Resist ASTM A439 Type D3 Ni-Resist ASTM A439 Type D3 Nitrited 40 xternal Seal Ring PTF (Bronze) 41 Internal Seal Ring Nordel 45 xternal Seal Ring Graphite 4 Internal Seal Ring Ni-Resist Cast Iron ASTM A439 Type D3 Temperature Range -19 C -4 C -29 C +149 C +2 C +343 C +5 C 12
Optional Trim Types 41512-412- 41912 Single Stage Multi-hole ow Noise and Cavitation Protection DN 50 - DN 0 Shown (2" - 4") 41413 Multi-hole, ow Noise and Cavitation Protection Trim with Internal Diffuser DN 150 - DN 400 (" - ") 41311 Pressure nergized Seal DN 150 - DN 400 Shown (" - ") 41314 Double Stage High Attenuation, ow Noise Trim DN 50 - DN 0 Shown (2" - 4") 13
Allowable Pressure Drops for 41400 Series Flow To Close Models 41411 and 41421 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV (V Optional) Kevlar PTF Packing Valve - mm (inch) Rated C V bench net supply P bench net supply P AIR TO OPN AIR TO COS ANSI Class and equivalent PN Travel ine qual % 150 300,, 2500 (mm) full reduced full reduced range range range range 50 50 (2) (2) 50 80 (2) (3) 80 80 0 (3) (3) (4) 0 0 150 (4) (4) () 20.3 38.1 50.8 50.8 40 35 14 75 5 2 30 155 140 5 0 0 225 90 95 11-4- 2.0 29 3-15 3-22 1.9 29 21-45 14-45 3.8 57.5-30 -37 3.0 57.5 11-7- 2.0 48 3-15 3-19 1. 48 21-45 17-45 3.8 9-30 -34 2.8 9-30 3-30 2.7 153 3-15 3-1.5 77 11-8- 1.9 77-30 -33 2.7 153-30 4-30 2.7 220 - - - - 11-9- 1.9 1 - - - - 11-4- 1.9 28 3-15 3-22 1.9 28 21-45 14-45 3.7 5-30 -37 3.0 5 11-7- 1.9 4 3-15 3-19 1. 4 21-45 17-45 3.7 93-30 -34 2.8 93-30 3-30 2. 148 3-15 3-1.5 74 11-8- 1.9 74-30 -33 2.7 148 11-5- 2.0 32 3-15 3-21 1.8 32 21-45 15-45 3.8 4-30 -3 2.9 4 11-7- 2.0 51 3-15 3-19 1. 51 21-45 17-45 3.8 2-30 -34 2.7 2-30 3-30 2.7 147 3-15 3-1.5 73 11-8- 2.0 73-30 -33 2.7 147 11-5- 2.0 31 3-15 3-21 1.8 31 21-45 15-45 3.8 2-30 -3 2.9 2 11-7- 2.0 49 3-15 3-19 1. 49 21-45 17-45 3.8 99-30 -34 2.7 99-30 3-30 2.7 142 3-15 3-1.5 71 11-8- 2.0 71-30 -33 2.7 142 - - - - 21-45 21-48 3.8 142 21-45 13-45 3.8 70 3-15 3-1.9 35 - - - - -30-38 3.1 70 11-5- 2.0 51 3-15 3-21 1.7 50 21-45 15-45 3.8 1-30 -3 2.9 1 21-45 13-45 3.8 7 3-15 3-1.9 34 - - - - -30-38 3.1 7 11-5- 1.9 48 3-15 3-21 1.7 48 21-45 15-45 3.8 97-30 -3 2.9 97 21-45 13-45 3.9 0 3-15 3-1.9 30 - - - - -30-38 3.1 0 11-5- 2.0 43 3-15 3-21 1.7 43 21-45 15-45 3.8 8-30 -3 2.9 8 21-45 13-45 3.8 5 3-15 3-1.9 28 - - - - -30-38 3.1 5 21-45 15-45 3.8 81 3-15 3-21 1.7 40.5 - - - - -30-3 2.9 81 - - - - 21-45 21-51 4.0 81 Nominal bench range of actuator used for specifying actuator on valve data sheet Actual bench range of valve/actuator assembly, resulting from combined pilot plug load force and actuator nominal bench range Model 87/88 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 14
Allowable Pressure Drops for 41400 Series Flow To Close Models 41411 and 41421 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV (V Optional) Kevlar PTF Packing Model 87/88 and 37/38 s Valve - mm (inch) Rated C V Travel AIR TO OPN AIR TO COS ANSI Class and equivalent PN inear qual % bench net supply P bench net supply P 150 300,, 2500 (mm) full reduced full reduced range range range range 150 150 150 200 () () () (8) 200 200 200 (8) (8) (8) 250 250 250 () () () 300 300 300 (12) (12) (12) 400 400 400 () () () 50.8 400 -- 30 144 20.3 5 3.5 40 575 0 38.1 415 7.2 00 38.1 5 95.25 1400 120 50.8 770 1. 2000 3.5 1280 21-45 12-45 4.1 71 3-15 3-2.0 20 - - - - -30-39 3.1 4 11-5- 2.2 0 3-15 3-21 1.8 31.5 21-45 15-45 4.1 2-30 -3 2.9 8 - - - - 3-15 3-29 2.4 4.1 - - - - 11-11-37 3.0 20 21-45 12-45 4.1 28 3-15 3-2.0 7.8 - - - - 11-11-32 2. 34 11-5- 2.8 0 3-15 3-21 1.8 12 - - - - 11-11-29 2.4 49 21-45 9-45 4.1 37 3-15 3-28 2.3 12 - - - - -30-43 3.4 29 21-45 12-45 4.1 70 3-15 3-2.0 19.5 - - - - -30-39 3.1 45 21-45 9-45 4.1 8.9 3-15 3-28 2.3 4.4 - - - - 11-11-3 2.9 22 21-45 12-45 4.1 27 3-15 3-2.0 7.3 - - - - 11-11-32 2. 32 9-41 3-42 4.0 52 7-38 7-48 3.9 45-50 3-50 4.1 15 4-45 4-5 4.1 2 9-44 4-44 4.1-40 -47 3.8 55-40 3-42 4.1 8 4-50 4-57 4.1 3 21-45 9-45 4.1 5.9 3-15 3-28 2.3 2.9 - - - - -30-43 3.4 7.2 - - - - 11-11-3 2.9 14 21-45 12-45 4.1 9.1 3-15 3-2.0 4.8 - - - - -30-39 3.1 11 - - - - 11-11-32 2. 21 9-28 3-29 2.7 19-27 -38 3.0 - - - - 3-45 3-5 4.1 12 11-50 -50 4.1 14-28 -3 2.9 34-28 3-30 2.9 3 3-25 3-33 2. 21-45 9-45 4.1 3.4-30 -43 3.4 4.8 - - - - 11-11-3 2.9 9. 21-45 12-45 4.1 5.5-30 -39 3.1 7.3 - - - - 11-11-32 2. 14 12-30 5-30 2.8 8.9 3-15 3-2 2.1.8 - - - - -30-41 3.3 14-30 3-32 3.1 20 3-15 3-2.0 9.3 - - - - -30-38 3.1 20 21-45 12-45 4.1 1. -30-39 3.1 4.2 - - - - 11-11-32 2. 8.2 Nominal bench range of actuator used for specifying actuator on valve data sheet Actual bench range of valve/actuator assembly, resulting from combined pilot plug load force and actuator nominal bench range Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 15
Allowable Pressure Drops for 41400 Series o-db/anti-cavitation Flow to Close Models 41412 and 41413 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV (V Optional) Kevlar PTF Packing Valve - mm (inch) Rated C V bench net supply P bench net supply P AIR TO OPN AIR TO COS ANSI Class and equivalent PN Travel High 150 300,, 2500 (mm) Capacity Standard Reduced range range range range 50 50 20.3 30 25 12 (2) (2) 50 80 38.1 5 50 25 (2) (3) 80 80 0 (3) (3) (4) 50.8 120 95 45 0 0 150 50.8 195 145 70 (4) (4) () 150 150 150 200 () () () (8) 200 200 200 (8) (8) (8) 250 250 250 () () () 3.5 300 2 5 7.2 500 315 155 88.9 50 500 250 300 300 300 1. 725 (12) (12) (12) 400 400 1. 1200 () () Model 87/88 and 37/38 s 11-4- 1.9 28 3-15 3-22 1.9 28 21-45 14-45 3.7 5-30 -37 3.0 5 11-7- 1.9 47 3-15 3-19 1. 47 21-45 17-45 3.7 94-30 -34 2.8 94-30 3-30 2. 150 3-15 3-1.5 75 11-8- 1.9 75-30 -33 2.7 150 11-5- 2.0 31 3-15 3-21 1.8 31 21-45 15-45 3.8 2-30 -3 2.9 2 11-7- 2.0 50 3-15 3-19 1. 50 21-45 17-45 3.8 0-30 -34 2.7 0-30 3-30 2.7 143 3-15 3-1.5 72 11-8- 2.0 72-30 -33 2.7 143 21-45 13-45 3.8 8 3-15 3-1.9 34 - - - - -30-38 3.1 8 11-5- 1.9 49 3-15 3-21 1.7 49 21-45 15-45 3.8 98-30 -3 2.9 98 21-45 13-45 3.8 58 3-15 3-1.9 29 - - - - -30-38 3.1 58 11-5- 2.0 41 3-15 3-21 1.7 41 21-45 15-45 3.8 83-30 -3 2.9 83 21-45 12-45 4.1 83 3-15 3-2.0 2.5 - - - - -30-39 3.1 0 11-5- 2.1 59.5 3-15 3-21 1.8 41 21-45 15-45 4.1 119-30 -3 2.9 87 9-41 3-42 3.8 9 5-4 5-57 4.1 5-40 3-40 3. 3-43 -54 4.1 71-40 3-42 3.8 115-40 -47 3.8 14-30 -30 2. -30-41 3.3 39 13-27 5-27 2.3 15 5-43 5-54 4.1 39.5 9-30 4-30 2.8 44-30 -38 3.0 54.5 12-48 7-48 4.1 45 7-28 7-3 2.9 45 12-30 5-30 2.8 19-30 -41 3.3 30-34 3-34 3.4 30 - - - - -30 3-32 3.1 44-30 -38 3.1 43 12-30 5-30 2.9 13-30 -41 3.3-34 3-34 3.5 21 - - - - -30 3-32 3.3 32-30 -38 3.1 25 Nominal bench range of actuator used for specifying actuator on valve data sheet Actual bench range of valve/actuator assembly, resulting from combined pilot plug load force and actuator nominal bench range Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.
Allowable Pressure Drops for 4, 400 and 41 Series Flow To Close Models 41511, 41521, 411, 421, 41911 and 41921 4 eakage : IC 534-4 and ANSI/FCI 70.2, Class II (2" - 4") 400 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV 41 eakage : IC 534-4 and ANSI/FCI 70.2, Class III (2" - 4") Kevlar PTF Packing Model 87/88 Valve - mm (inch) Rated C V Travel ANSI Class and equivalent PN inear qual % 150 300,, 2500 (mm) full reduced full reduced range range 50 50 20.3 (2) (2) 50 80 38.1 (2) (3) 80 80 0 (3) (3) (4) 0 0 150 (4) (4) () 50.8 50.8 40 35 14 75 5 2 30 155 140 5 0 0 225 90 95 AIR TO OPN AIR TO COS bench supply P bench supply P 3-15 1.3 28 3-15 1.3 28-30 2. 55-30 2.5 55 3-15 1.3 4 3-15 1.3 4-30 2. 92-30 2.5 92 3-15 1.3 73.5 3-15 1.3 73.5-30 2. 147-30 2.5 147 3-15 1.3 27 3-15 1.3 27-30 2. 55-30 2.5 55 3-15 1.3 4 3-15 1.3 4-30 2. 91-30 2.5 91 3-15 1.3 73 3-15 1.3 73-30 2. 14-30 2.5 14 3-15 1.3 30.5 3-15 1.3 30.5-30 2. 1-30 2.5 1 3-15 1.3 49 3-15 1.3 49-30 2. 97.5-30 2.5 97.5 3-15 1.3 70 3-15 1.3 70-30 2. 140-30 2.5 140 3-15 1.3 30 3-15 1.3 30-30 2. 0-30 2.5 0 3-15 1.3 48 3-15 1.3 48-30 2. 9.5-30 2.5 9.5 3-15 1.3 9 3-15 1.3 9-30 2. 139-30 2.5 139 3-15 1.3 33 3-15 1.3 33-30 2..5-30 2.5.5 3-15 1.3 48 3-15 1.3 48-30 2. 9-30 2.5 9 3-15 1.3 33 3-15 1.3 33-30 2. 5-30 2.5 5 3-15 1.3 47 3-15 1.3 47-30 2. 94-30 2.5 94 3-15 1.3 28 3-15 1.3 28-30 2. 55-30 2.5 55 3-15 1.3 40 3-15 1.3 40-30 2. 80-30 2.5 80 3-15 1.3 27 3-15 1.3 27-30 2. 54.5-30 2.5 54.5 3-15 1.3 39 3-15 1.3 39-30 2. 78-30 2.5 78 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 17
Allowable Pressure Drops for 4, 400 and 41 Series Flow To Close Models 41511, 41521, 411, 421, 41911 and 41921 4 eakage : IC 534-4 and ANSI/FCI 70.2, Class III (" - ") 400 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV 41 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV (" - ") Kevlar PTF Packing Model 87/88 and 37/38 s Valve - mm (inch) Rated C V AIR TO OPN AIR TO COS bench supply P bench supply P ANSI Class and equivalent PN Travel inear qual % 150 300,, 2500 (mm) full reduced full reduced range range 3-15 1.5 39 3-15 1.3 2.5-30 2.9 78-30 2.5 0 50.8 400 30 144 3-15 1.5 5 3-15 1.3 41 150 150 150 200-30 2.9 112-30 2.5 87 () () () (8) 3-15 1.8 39 3-15 1.3 13-30 3.5 78-30 2.5 28 20.3 5 3-15 1.7 5 3-15 1.3 19.5-30 3.5 112-30 2.5 42 3-15 1.4 3-15 1.3 19-30 2.8 48-30 2.5 4 3.5 40 575 0 3-15 1.4 34 3-15 1.3 31-30 2.7 9-30 2.5 9 200 200 200 3-15 1.7-30 2.5 19 (8) (8) (8) -30 3.3 48 21-45 3. 48 38.1 415 3-15 1.7 34 3-15 1.3 13-30 3.3 9-30 2.5 29 11-2.3 34 11-1.9 34 - - - 21-45 3. 9-27 2.5 32-27 2.2 33-48 4.1 38-48 3. 0 7.2 00 9-41 3.7 49 7-38 2.8 49-40 3.7 82-40 3.0 81.5-52 4.1 20-52 3.9 84 250 250 250-30 3.4 3-30 2.5 13 () () () - - - 21-45 3. 3 38.1 5 3-15 1.7 2 3-15 1.3 8.8-30 3.4 51.5-30 2.5 20 - - - 11-1.9 2 - - - 21-45 3. 51.5 95.25 1400 120-27 2. -27 2.0-28 2. 35-28 2.1 35-30 3.4 27-30 2.5 300 300 300 - - - 21-45 3. 27 (12) (12) (12) 3-15 1.7 19.5 3-15 1.3.7 50.8 770-30 3.4 39-30 2.5 15 - - - 11-1.9 19.5 - - - 21-45 3. 39 1. 2000-30 2.7 15 3-15 1.2 8.0 - - - -30 2.2 15 3-15 1.3 9.8 3-15 1.1 9.8-30 2. 20-30 2.1 20 400 400 400-30 3.4-30 2.5.1 () () () - - - 21-45 3. 3-15 1.7 12 3-15 1.3 4.0 3.5 1280-30 3.4-30 2.5 9.2 - - - 11-1.9 12 - - - 21-45 3. Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.
Allowable Pressure Drops for Single Stage Series Anti-cavitation Trim Flow To Close Models 41512, 41513, 412, 413, 41912 and 41913 4 eakage : IC 534-4 and ANSI/FCI 70.2, Class II (2" - 4") 4 eakage : IC 534-4 and ANSI/FCI 70.2, Class III (" - ") 400 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV 41 eakage : IC 534-4 and ANSI/FCI 70.2, Class III (2" - 4") 41 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV (" - ") Kevlar PTF Packing Valve - mm (inch) Rated C V AIR TO OPN AIR TO COS ANSI Class and equivalent PN Travel High bench supply P bench supply P 150 300,, 2500 (mm) Capacity Standard Reduced range range 50 50 (2) (2) 50 80 (2) (3) 80 80 0 (3) (3) (4) 0 0 150 (4) (4) () 150 150 150 200 () () () (8) 200 200 200 (8) (8) (8) 250 250 250 () () () 300 300 300 (12) (12) (12) 400 400 () () 20.3 30 25 12 38.1 5 50 25 50.8 120 95 45 50.8 195 145 70 3.5 300 2 5 7.2 500 315 155 88.9 50 500 250 1. 725 1. 1200 Model 87/88 and 37/38 s 3-15 1.3 27 3-15 1.3 27-30 2. 55-30 2.5 55 3-15 1.3 4 3-15 1.3 4-30 2. 91-30 2.5 91 3-15 1.3 73 3-15 1.3 73-30 2. 14-30 2.5 14 3-15 1.3 5 3-15 1.3 5-30 2. 2-30 2.5 2 3-15 1.3 30 3-15 1.3 30-30 2. 0-30 2.5 0 3-15 1.3 48 3-15 1.3 48-30 2. 9.5-30 2.5 9.5 3-15 1.3 9 3-15 1.3 9-30 2. 139-30 2.5 139 3-15 1.3 33 3-15 1.3 33-30 2. 5.5-30 2.5 5.5 3-15 1.3 47 3-15 1.3 47-30 2. 94-30 2.5 94 3-15 1.3 27 3-15 1.3 27-30 2. 55-30 2.5 55 3-15 1.3 39 3-15 1.3 39-30 2. 79-30 2.5 79 3-15 1.5 48 3-15 1.3 33-30 2.9 95-30 2.0 74 3-15 1.4 8.5 3-15 1.0 51-30 2.9 137-30 2.0-48 4.1 2.5 3-13 1.1 22 15-50 4.1 38 3-35 2.8 48.5 - - - -48 3.8 89-30 2.7 34 3-15 1.3 19 - - - -30 2.2 35 9-40 3. 5 3-25 1.9 43 12-48 4.1 59 - - - -30 2.9 30 3-9 0.8 7. -34 3.2 27 3-15 1.3 - - - -30 2.5 31-30 2.9 40 3-15 1.1 20 - - - -30 2.1 41-30 3.0 21 3-9 0.8 5.4-34 3.3 19 3-15 1.3 11 - - - -30 2.5 22-30 3.0 29 3-15 1.3 14 - - - -30 2.5 29.5 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 19
Allowable Pressure Drops for 41300 Series Flow To Open Models 41311, 41321 and 41312 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV Kevlar PTF Packing Model 87/88 Valve ANSI Class and Travel equivalent PN (mm) Rated (1) C V AIR TO OPN (2) Allowable pressure drops Bench range AIR TO COS Allowable pressure drops Bench range 3-15 Bench range - 30 Supply Supply mm inch 3-15 - 30 11-21 - 45 1.4 1.7 2.4 2.8 3.1 75, 30 50 2 38.1 5 5, 50 O 14.5 3 - - 9 3 9 3 - ou 25 DB 50 2 20.3 40, 35 30, 25 ou 12 O DB - 83 8 172.5 57 8 57 138.5 172.5 57.5 139 144 258 115.5 144 115.5 1.5 258 80 3 50.8 155, 0 140 120, 95 ou 45 O DB 31 142.5 129.5 258 1 129.5 1 7 258 91 205.5.5 258 171.5.5 171.5 258-0 4 50.8 0, 95 225 195, 145 ou 70 O DB 4.5 113.5 8 2 81.5 8 81.5 2-58 198 15 258 152 15 152 258-150 50.8 3.5 400 30 300, 2 ou 5 O DB - 81 88.5 177.5 50.5 88.5 50.5 171 177.5 28.5 148.5 128 219 113 128 113 219-200 8 3.5 40 575-37 5 132.5 11 5 11 5.5 132.5-91.5 95.5 175 9 95.5 9 152 175 (1) : inear : qual percentage (2) Supply pressure is 0.4 bar (5 psi) over bench range o-db Trim Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 20
Allowable Pressure Drops for 41300 Series Flow To Open Models 41311, 41321 and 41312 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV Kevlar PTF Packing Models 41311 and 41321 Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V (1) AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P 250 300 400 12 300 7.2 95.3 1. 00 1400 120 2000 8-30 2.4 138 3-13 1.4 2.5 3-13 1.7 7.5-27 2.4 78-27 2.8 138-27 2.2 75 3-14 1.4.5-33 2.8 95 3-14 1.7 70.5-27 2.4 47.5-27 2.8 95-30 2.4 41 3-15 1.7 40 12-30 2.4 78 3-15 2.1 57-30 2.8 39-30 3.1 78 (1) : inear ; : qual percentage Model 41312 Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P 200 250 300 400 8 12 7.2 88.9 1. 1. 315 500 725 1200 8-30 2.4 14.5 3-13 1.4 88 15-50 3.8 175 3-13 1.7 89.5-27 2.4 97-27 2.8 15.5-27 3.1 175-30 2.4 4.5 3-15 1.4 7.0-30 2.4 13 3-15 1.7 90.5-30 2.8 113.5-30 3.1 138-30 2.4 75 3-15 2.1 75 12-30 2.4 95-30 2.8 74-30 3.1 95-30 2.4 41 3-15 1.7 40 12-30 2.4 78 3-15 2.1 57-30 2.8 39-30 3.1 78 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 21
Allowable Pressure Drops for 41300 Flow To Open Models 41311, 41321 and 41312 eakage : IC 534-4 and ANSI/FCI 70.2, Class V Kevlar PTF Packing Model 87/88 Valve ANSI Class and Travel equivalent PN (mm) Rated C V (1) AIR TO OPN (2) Allowable pressure drops Bench range AIR TO COS Allowable pressure drops Bench range 3-15 Bench range - 30 Supply Supply mm inch 3-15 - 30 11-21 - 45 2.1 2.4 2.8 3.1 3.5 3.8 75, 30 50 2 38.1 5 5, 50 O - - - 3 3 - - 3 - - ou 25 DB 50 2 20.3 40, 35 30, 25 ou 12 O DB - - - 172.5 31.5 8-31.5 172 - - - 130.5 258 144 - - 258 - - 80 3 50.8 155, 0 140 120, 95 ou 45 O DB - - 35 258 129.5 - - 194.5 258 - - -.5 258.5 - - 258 - - 0 4 50.8 0, 95 225 195, 145 ou 70 O DB - - - 2 81 8-81 2 - - - 9 258 15 - - 258 - - 150 50.8 3.5 400 30 300, 2 ou 5 O DB - - - 0.5-88.5 - - 134.5 177.5 - - 15 219 128 - - 178 219-200 8 3.5 40 575 - - - 33.5-7.5 5-7.5 120 - - - 175 51 95.5-51 175 - (1) : inear : qual percentage (2) Supply pressure is 0.4 bar (5 psi) over bench range o-db Trim Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 22
Allowable Pressure Drops for 41300 Series Flow To Open Models 41311, 41321 and 41312 eakage : IC 534-4 and ANSI/FCI 70.2, Class V Kevlar PTF Packing Models 41311 and 41321 Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V (1) AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P 250 300 400 12 300 7.2 95.3 1. 00 1400 120 2000 15-50 3.8.5 3-13 2.4.5 20-50 3.8 138 3-13 2.8 7.5-27 3.5 45.5-27 3.8 138 - - - 3-14 3.1 70.5-27 3.8 37-45 3.5 95-28 3.5 95-50 3.8 52 3-15 3.1 7 (1) : inear : qual percentage Model 41312 Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P 200 250 300 400 8 12 7.2 88.9 1. 1. 315 500 725 1200 15-50 3.8 111 3-13 2.4 89.5 20-50 3.8 175-27 3.1 21-27 3.5 143-27 3.8 175 - - - 3-15 2.8 77.5 3-15 3.1 90.5 19-4 3.5 138-30 3.1 8.5-30 3.5 138 - - - 3-15 3.1 38 3-15 3.5 75-50 3.8 95 3-15 2.8 95-50 3.8 52 3-15 3.1 7 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.
Allowable Pressure Drops for 41300 Series Flow To Open Model 41314 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV Kevlar PTF Packing Valve mm inch ANSI Class and Travel equivalent PN (mm) Rated C V AIR TO OPN (1) Allowable pressure drops Bench range 3-15 - 30 11-21 - 45 Bench range 3-15 Supply Model 87/88 AIR TO COS Allowable pressure drops Bench range - 30 Supply 1.4 1.7 2.4 2.8 3.1 50 2 38.1 35 57.5 139 144 258 115.5 144 115.5 1.5 258 80 3 50.8 5 88 209.5 3 258 174.5 3 174.5 258-0 4 3.5 125 31 142.5 129.5 258 1 129.5 1 7 258 91 205.5.5 258 171.5.5 171.5 258-150 3.5 150 4.5 113.5 8 2 81.5 8 81.5 2-58 198 15 219 152 15 152 219 - (1) Supply pressure is 0.4 bar (5 psi) over bench range Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V Bench range AIR TO OPN Supply P Bench range AIR TO COS Supply P 200 250 300 400 8 12 7.2 1. 1. 1. 300 4 800 8-30 2.4 14.5 3-13 1.4 88 15-50 3.8 175 3-13 1.7 89.5-27 2.4 97-27 2.8 15.5-27 3.1 175-30 2.4 4.5 3-15 1.4 2.5-30 2.4 132.5 3-15 1.7 88-30 2.8 2-30 3.1 138-30 2.4 75 3-15 2.1 75 12-30 2.4 95-30 2.8 74-30 3.1 95-30 2.4 41 3-15 1.7 40 12-30 2.4 78 3-15 2.1 57-30 2.8 39-30 3.1 78 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information.
Allowable Pressure Drops for 41300 Series Flow To Open Models 41314 eakage : IC 534-4 and ANSI/FCI 70.2, Class V Kevlar PTF Packing Valve mm inch ANSI Class and Travel equivalent PN (mm) Rated C V AIR TO OPN (1) Allowable pressure drops Bench range 3-15 - 30 11-21 - 45 Allowable pressure drops Bench range 3-15 Supply Model 87/88 AIR TO COS Bench range - 30 Supply 2.1 2.4 2.8 3.1 3.4 50 2 38.1 35 - - 130.5 258 144-87.5 258-80 3 50.8 5 - - 3 258 3-5 258-0 4 3.5 125 - - 35 258 129.5 - - 194.5 258 - -.5 258.5-173.5 258-150 3.5 150 - - - 2 81 8-81 2 - - 9 219 15-1.5 219 - (1) Supply pressure is 0.4 bar (5 psi) over bench range Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P 200 250 8 7.2 1. 300 4 15-50 3.8 111 3-13 2.4 89.5 20-50 3.8 175-27 3.1 21-27 3.5 143-27 3.8 175 - - - 3-15 2.8 51 3-15 3.1 88 19-4 3.5 138-30 3.5 7.5 300 400 12 1. 1. 800 - - - 3-15 3.1 38 3-15 3.5 75-50 3.8 95 3-15 2.8 95-50 3.8 52 3-15 3.1 7 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 25
Allowable Pressure Drops for 4, 400 and 41 Series Flow To Open Models 41511, 41521, 411, 421, 41911 and 41921 Models 41512, 41513, 412, 413, 41912 and 41913 4 eakage : IC 534-4 and ANSI/FCI 70.2, Class II (2" - 4") 4 eakage : IC 534-4 and ANSI/FCI 70.2, Class III (" - ") 400 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV 41 eakage : IC 534-4 and ANSI/FCI 70.2, Class III (2" - 4") 41 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV (" - ") Kevlar PTF Packing Model 87/88 Valve mm inch 50 50 80 0 150 200 250 300 400 2 2 3 4 8 12 ANSI Class and Travel equivalent PN (mm) 38.1 20.3 50.8 50.8 50.8 3.5 3.5 38.1 50.8 3.5 Rated C V 75, 30 5 5, 50 ou 25 40, 35 30, 25 ou 12 155, 0 140 120, 95 ou 45 0, 95 225 195, 145 ou 70 400 30 300, 2 ou 5 40 575 5 770 1280 (1) O DB O DB O DB O DB O DB AIR TO OPN (2) Allowable pressure drops Bench range 3-15 - 30 11-21 - 45 Allowable pressure drops Bench range 3-15 Supply AIR TO COS Bench range - 30 Supply 1.7 2.4 2.8 3.1 3.5 3.8-20 4 97.5 4-4 74 97.5-12 43 77.5 3 77.5-78.5 3 - - 2 7.5 3-3 - 3 - - - - 12.5 42 95.5 3 44.5 3 5 90.5 97.5 7.0 3 81.5 159.5 75 81.5 75 114 152 3.5 70.5 129.5 253 120.5 129.5 120.5 0.5 1 258 3.5.5 53 9 52.5 53 52.5 80.5 7.5 9 12.5 43.5 79 158 77.5 79 77.5 1.5 155 158-15.5 27.5 59.5 27.5-3.5 59.5 - - 7.0 29.5 42 87 42-59 87 - - - 15.5 3.5.5-3.5 - - - 4.5 31.5 25 54 25-54 - - - - 5.0 11.5 27 11.5-21 27 - - -.5 41.5-38.5 41 - - - 1.5 9.0 22 9.0-13.5 22 - - - 9.5 15 33.5 15-2.5 33.5 - - - - 5.0 12 5.0-7.0 12 - - - 4.0 8.0 8.0-15.5 - - - - 3.5 8.5 3.0 3.5 3.0 8.5 - - - 1.0.0 13.0-8.5 13 - - (1) : inear ; : qual percentage (2) Supply pressure is 0.4 bar (5 psi) over bench range o-db Trim Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 2
Allowable Pressure Drops for 4, 400 and 41 Series Flow To Open Models 41511, 41521, 411, 421, 41911 and 41921 Models 41512, 41513, 412, 413, 41912 and 41913 4 eakage : IC 534-4 and ANSI/FCI 70.2, Class III (" - 12") 400 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV 41 eakage : IC 534-4 and ANSI/FCI 70.2, Class IV (" - 12") Kevlar PTF Packing Models 41511, 41521, 411, 421, 41911 and 41921 Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V (1) AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P 250 7.2 00-48 3.8 3-13 3.8 13.5 8-30 3.8 31-40 3.1 28-40 3.8 1 300 12 95.25 1400 120-27 2.4 8.5 3-30 3.8 22.5-28 2.4.5-28 3.8.5 400 1. 2000-34 2.8 12-30 3.4 13.5-30 2.4 9.5 3-15 1.7 8.5-30 3.1 19 (1) : inear : qual percentage Models 41512, 41513, 412, 413, 41912 and 41913 Model 37/38 Valve mm inch ANSI Class and equivalent PN Travel (mm) Rated C V AIR TO OPN Bench Supply P range AIR TO COS Bench range Supply P 200 250 300 400 8 12 7.2 88.9 1. 1. 315 500 725 1200-48 3.8 3-13 3.8 17 15-50 3.8 0 3-35 3.8 1.5-52 3.8 40.5-40 3.8 79-30 2.8 3-15 3.8 17-30 3.8 34.5 9-30 2.4 41.5-30 3.5 49 13-50 3.8 71-34 2.8 17.5-30 3.5.5-30 2.8.5 3-15 1.7 12-30 3.1 2-34 2.8 12-30 3.5 13.5-30 2.4 9.5 3-15 1.7 8.5-30 3.1 19 Note : Inlet pressure must not exceed the quoted rating for the selected pressure class. Values in italics correspond to throtling delta P limitation for stability. Shutoff delta P is greater, consult Masoneilan. All pressure drops ( P) shown within this publication reflect actuator capability and shutoff class shown for a particular trim type. It does not imply proper application with regards to cavitation, noise, critical pressure drop, etc. Consult Masoneilan Handbook for Control Valve Sizing OZ00 for more information. 27
Dimensions (mm) Flanged Butt, Socket Weld or Screwed nds Body S/A Pressure Class ANSI Class 150 ANSI Class 300 and equivalent PN and equivalent PN Valve BW BW BW RF RTJ & RF RTJ & RF RTJ & RF RTJ mm inch SW SW SW 50 2 - - 390 27 283 390 28 289 398 375 378 80 3 434 3 334 434 337 340 434 441 445 - - 80x50x80 3x2x3 (a) (a) (a) 0 4 492 39 384 492 394 397 492 511 514 0x50x0 4x2x4 - - (a) (a) (a) 0x80x0 4x3x4 492 511 514 150 451 44 50 473 489 50 508 511 80 714 717 150x80x150 x3x 150x0x150 x4x 200 8 543 55 5 59 584 5 13 854 915 9 200x0x200 8x4x8 200x150x200 8xx8 250 73 8 802 708 7 802 752 755 892 92 95 250x150x250 xx 300 12 737 750 822 775 791 822 819 822 34 1130 1133 300x200x300 12x8x12 400 29 02 57 72 (a) 1111 00 1375 1384 400x300x400 x12x (a) (a) (a) (a) A ANSI Class and equivalent PN ANSI Class and equivalent PN (a) Consult Masoneilan 28
Dimensions (mm) Body S/A A B max C max Pressure Class ANSI Class ANSI Class 2500 and equivalent PN and equivalent PN All All Valve BW BW & RF RTJ & RF RTJ Classes Classes mm inch SW SW 50 2 398 375 378 388 400 403 94 250 80 3 434 40 44 93 300 (a) (a) (a) 80x50x80 3x2x3 (a) (a) (a) 0 4 492 531 533 (a) (a) (a) 112 330 0x50x0 4x2x4 (a) (a) (a) - - - 0x80x0 4x3x4 492 531 533 - - - 150 80 78 774 70 (a) (a) 394 150x80x150 x3x - - - 150x0x150 x4x - - - 200 8 854 972 981 (a) (a) (a) 205 521 200x0x200 8x4x8 - - - 200x150x200 8xx8 - - - 250 892 1178 7 571 - - 250x150x250 xx - 300 12 (a) 12 14 359 2 - - - 300x200x300 12x8x12 (a) (a) (a) 400 (a) 1508 1530 449 94 - - - 400x300x400 x12x (a) (a) (a) Note : For AFNOR and DIN dimensions, consult Masoneilan (a) Consult Masoneilan 29
Dimensions (mm) Shown with optional handwheel Model 87/88 Spring Diaphragm P R S T 292 394 254 228 38 497 277 305 47 717 330 457 549 780 381 457 removal clearance = 150 mm 30
Dimensions (mm) Direct (37) Air to Close Reverse (38) Air to Open Direct (37) Air to Close Type 8A Handwheel Reverse (38) Air to Open Model 37/38 Spring Diaphragm Top-Mounted Handwheel Removal D F Type G H J Clearance Dir. Rev. Dir. Rev. with " Spring 142 527 843 9 8A 203 134 134 with 20" Spring 142 527-1321 8A 203-134 127 99 881 115 8A 305 134 1473 * 1 /2" NPT for No. 31
Weights (kg) Body S/A Weights Valve Flanged Connection Threaded / Welded Connection ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class ANSI Class 150, 300 and and and and 2500 and and and and 2500 and mm inch equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN equivalent PN 50 2 45 45 5 5 9 3 39 39 39 80 3 0 0 147 0 2 84 113 113 1 0 4 5 9 0 8 299 127 5 5 222 150 5 20 52 53 57 4 394 394 471 200 8 4 439 92 8 997 353 701 701 845 250 30 77 1270-547 714 973-300 12 980 15 1497 179-954 1211 1320-400 1454 150 - - - 1412 - - - Model 87/88 Spring Diaphragm Standard With Handwheel 20 27 38 48 95 111 120 154 Model 37/38 Spring Diaphragm Standard With Handwheel Direct Reverse Direct Reverse () 8 7 4 (20) - 204-222 147 5 179 27 32
Accessories and Options Accessories Side Mounted Handwheels For 87/88 s (See Specification Data CR8788 ) Top Mounted Handwheels For 37/38 s (See Specification Data CR3000) 4700 P Series Pneumatic Positioner Instrument signals 0.2-1 and 0.4-2 bar 3-15 and -30 psig Split range 4700 Series lectropneumatic Positioner 8013 Series lectropneumatic Positioner Input range 4-20 ma Split range 77-4 or 77-40 Airset (See Bulletin 78 ) 77- ockup Valve 2'' Gauge 0-2 bar 49 Rotary lectric Switches 49-1 (1-Switch SPDT) 49-2 (2-Switches SPDT) 49-3 Potentiometer Position Transmitter 49-4 (1-Proximity Detector) 49-5 (2-Proximity Detectors) 49- (1-Switch DPDT) 49-7 (2-Switches DPDT) 49-8 Opto-electronic Position Transmitter (See Specification Data CS7050 ) Other imit Switches 7000 lectropneumatic (I/P) Transducer Input range 4-20 ma Split range Output 0.2-1 bar, adjustable 0.4-2 bar, adjustable 3-15 psi, adjustable -30 psi, adjustable (See TS-Model 7000) Smart Valve Interface (SVI ) Smart Positioner and Smart Valve Process Controller Input range 4-20 ma Split range HART Communication (See Brochure BW00 ) ValVue Software Calibration, Configuration, Diagnostic, and Operator Interface Tool (See Brochure BW00 ) Solenoid Valves Options xtension Bonnets nvironmental Capabilities ( Packing) ubricator & Isolation Valve Other Flange Facings imit Stops Body Drain Plug Reducer and Nipple Connections NAC Compliance Custom Trim Materials U.O.P. Trim Materials Other Materials Soft Seat (IC 534-4 and ANSI Class VI) Non-Destructive xamination Oxygen Cleaning lectric s For additional Accessories and Options, consult Masoneilan 2700 Controllers (See Bulletin 213 ) 33
Notes 34
Notes 35