Series 1000 Desk Products Installation Instructions Return Worktop Rectangular Desk Peninsula Bridge Worktop Bow Front Desk Grand Peninsula Corner Desk - Straight Front L-Return Desk - Straight Front Radius Panel Worktop - Verse Wire Manager Tray Corner Desk - Radius Front L-Return Desk - Radius Front Maxon Furniture Inc. an HNI Corporation company www.maxoninfo.com Customer Service 1-800-876-4274 REV. - September 2005 SHEET 1 OF 6
Rectangular/Bow Front Desks Pre-assembly notes on Series 1000 Installation and Application: - Peninsulas are not intended for "stand-alone" use and must be attached to at least one Return Worktop or Bridge Worktop. - Return Worktops and Bridge Worktops with modesty panels cannot be connected to Desks with C-Legs. - Wire manager trays are 2.5" deep and should not be installed behind pedestals or lateral files. Steps 1-4: 1. With the worktop face down on the floor, attach one end panel or C-leg to the worktop with four If using a C-leg, see the separate instructions for pre-assembling C-legs. Head 2. Attach the modesty panel to the leg with black truss head screws (two for half modesties, three for full modesties). 3. Attach the modesty panel to the worktop with four 4. Attach the second leg to the worktop as in step 1 and to the modesty panel as in step 2. Steps 5-6: 5. The optional wire manager tray can be installed anyplace under the worktop. Suggested location is against the modesty panel - use a long screwdriver to remove two screws, align the tray holes with the modesty holes, then re-install the screws. 6. The leveling glides should be adjusted the same amount, then turn the desk upright and adjust the glides as necessary to achieve a level worktop. SHEET 2 OF 6
A Corner Desk is shown. An L-Return Desk is similar but will have a Full Depth End Panel or C-Leg installed on the long end of the desk. Steps 1-4: 1. With the worktop face down on the floor, attach one end panel to the worktop with two 2. Attach the modesty panel to the end panel with black truss head screws (two for half modesties, three for full modesties). 3. Attach the modesty panel to the worktop with four panhead screws. 4. Attach the corner post to the modesty panel with black truss head screws - leaving the second set of holes facing the inside of the unit. Corner Desks / L-Return Desks Head Steps 5-10: 5. Attach the second modesty panel to the corner post with black truss head screws. Head 6. Attach the modesty to the worktop with four 7. Attach the second end panel or C-leg to the modesty panel with black truss head screws. 8. Attach the second leg to the worktop with panhead screws. 9. The optional wire manager tray can be installed anyplace under the worktop. Suggested location is against the modesty panel - use a long screwdriver to remove two screws, align the tray holes with the modesty holes, then re-install the screws. 10. The leveling glides should be adjusted the same amount, then turn the desk upright and adjust the glides as necessary to achieve a level worktop. SHEET 3 OF 6
Step 1: Peninsulas Peninsulas are not intended for "stand-alone" use and must be attached to at least one Return Worktop or Bridge Worktop. 1. Attach the 9" x 9" mounting plate to the column leg with two 1/4-20 x 1" machine screws. 1/4-20 x 1" Machine Steps 2-4: 2. With the worktop face down on the floor, attach one end panel leg to the worktop with two 3. Attach the modesty panel to the end panel with black truss head screws (two for half modesties, three for full modesties). 4. Attach the modesty panel to the worktop with four Steps 5-10: 5. Attach the second end panel leg to the modesty panel with black truss head screws. 6. Attach the second leg to the worktop with two panhead screws. SHEET 4 OF 6 7. Attach the column leg/plate assembly from step 1 to the worktop with four 8. The leveling glides should be adjusted the same amount, then turn the unit upright and adjust the glides as necessary to achieve a level worktop.
Return Worktops NOTE: Return Worktops with modesty panels cannot be connected to Desks with C-Legs (use a No Modesty (-NM) Return Worktop instead. - Wire manager trays are 2.5" deep and should not be installed behind pedestals or lateral files. Steps 1-4: 1. With the worktop face down on the floor, attach the end panel or C-leg to the worktop with four If using a C-leg, see the separate instructions for pre-assembling C-legs. 2. Attach the modesty panel or gusset to the leg with black truss head screws (two for half modesties and gussets, three for full modesties). 3. Attach the modesty panel or gusset to the worktop with panhead screws (four for modesties, two for gussets). 4. If attaching to a Desk with End Panels, attach two Modesty Brackets to the Return Modesty with black truss head screws, otherwise proceed to step 5. Steps 5-6: 5. Attach two Universal Flat Brackets to the Desk or other unit with Set the Return Worktop upright and onto the Flat Brackets and secure with Attach the modesty panel to the Desk's End Panel using the Modesty Brackets and secure with black truss head screws (if attaching to a Corner Desk, L-Return, or Peninsula, then do not use the Modesty Brackets - screw directly through the end of the modesty panel into the holes of the mating End Panel - see page 6 Bridge Worktops for an example). 6. Adjust the leveling glides as necessary. Modesty Attaching Bracket SHEET 5 OF 6
Bridge / Radius Panel Worktop NOTE: Bridge Worktops with modesty panels cannot be connected to Desks with C-Legs (use a No Modesty (-NM) Bridge Worktop instead. Bridge Worktop Steps 1-3: 1. Attach two Universal Flat Brackets to each Desk or other unit that the Bridge will connect onto with Set the Bridge Worktop onto the Flat Brackets and secure with 2. Attach the modesty panel (if so equipped) to the Bridge Worktop with four panhead screws, then attach the modesty panel to the Desks' End Panels using the Modesty Brackets and secure with black truss head screws. If attaching to a Corner Desk, L-Return, or Peninsula, then do not use the Modesty Brackets - screw directly through the end of the modesty panel into the holes of the mating End Panel. 3. Adjust the leveling glides as necessary on the connected units. Modesty Attaching Bracket Radius Panel Worktop Steps 1-3: 1. Attach two Universal Flat Brackets to each Desk or other unit that the Worktop will connect onto with Set the Worktop onto the Flat Brackets and secure with 2. Slide a Panel Attaching Bracket between the fabric and the radius panel frame. Slide the Bracket up against the Worktop and secure with panhead screws. The second Bracket may have to be flipped over to attach correctly to the panel and Worktop. SHEET 6 OF 6 Panel Attaching Bracket 3. Adjust the leveling glides as necessary on the connected units.