KA0 ILLUSTRATED LUSTR TED ASSEMBLY SE MANUAL HKA0P KA0 IN/OUT shield for Arduino General purpose INPUT - OUTPUT shield for Arduino Features For use with Arduino Due, Arduino Uno, Arduino Mega analog inputs digital input relay contact outputs Indicator leds for relay outputs and digital inputs Specifications Analog inputs: 0..+VDC Digital inputs: dry contact or open collector Relays: V Relay contacts: NO/NC VDC/A max. Dimensions: 8 x mm /.7 x.08
Forum Participate our Velleman Projects Forum Subscribing our newsletter?, visit www.vellemanprojects.eu
Velleman N.V. Legen Heirweg 9890 Gavere (België)
assembly hints. Assembly (Skipping this can lead to troubles! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.. Make sure you have the right tools: A good quality soldering iron (-0W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any fl ux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fl y towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fi ne. For some projects, a basic multi-meter is required, or might be handy. Assembly Hints : Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes, the values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet.. Soldering Hints :. Mount the component against the PCB surface and carefully solder the leads 0.000. Make sure the solder joints are cone-shaped and shiny. Trim excess leads as close as possible to the solder joint - -
DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR VALUE ON THE PARTS LIST! - -
Construction I CONSTRUCTION Zenerdiodes Transistors Ceramic capacitor c... ZD : V ZD : V ZD : V ZD : V ZD : V ZD : V T: BC7B T: BC7B T: BC7B T: BC7B T: BC7B T: BC7B c... C: 00nF (0) Diodes D : N8 D : N8 D : N8 D : N8 Watch the polarity! D : N8 D : N8 D7 : N8 D8 : N8 D9 : N8 D0: N8 D: N8 D: N8 Watch the polarity! C (-) C (-) LED LD : Red LD : Red LD : Red LD : Red LD : Red LD : Red Watch the polarity! LD7 : Green LD8 : Green LD9 : Green LD0 : Green LD : Green LD : Green - - Resistors R... R : K ( - 0 - - B) R : K ( - 0 - - B) R : K ( - 0 - - B) R : K ( - 0 - - B) R : K ( - 0 - - B) R : K ( - 0 - - B) R7 : ( - 7 - - B) R8 : 0K ( - 0 - - B) R9 : ( - 7 - - B) R0 : 0K ( - 0 - - B) R : ( - 7 - - B) R : 0K ( - 0 - - B)
Construction R: R: R: R: R7: R8: R9: R0: R: R: R: R: R: R: R7: R8: R9: R0: 0K 0K 0K ( - 7 - - B) ( - 0 - - B) ( - 7 - - B) ( - 0 - - B) ( - 7 - - B) ( - 0 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) ( - 7 - - B) 7 Terminal blocks 8 x p (INPUTS) 8 Relays 9 Electrolytic capacitors RY RY RY RY RY RY Watch the polarity! C : 00μF! 0 Male header CUT CUT CUT CUT X pins X 8 pins x p (OUTPUTS) -7-
Connection diagram II CONNECTION DIAGRAM OUTPUT MAX. VDC / A DIGITAL INPUTS RELAY OUTPUTS (Max. VDC/A) DIGITAL INPUTS 000000...... ANALOG INPUTS 0... V ANALOG INPUTS ANALOG DOWNLOAD SAMPLE CODE FROM KA0 PAGE ON WWW.VELLEMAN.BE - 8 -
- 9 - SK V V RST SK A0 A A A A A 7 8 SK ARDUINO UNO 7 8 SK 0 7 8 9 0 AREF - V LEDRL LD7 LEDRL LD8 LEDRL LD9 LEDRL LD0 LEDRL LD LEDRL LD R9 R0 R R R R - N8 D N8 D N8 D N8 D N8 D N8 D 7 DI DI DI DI DI DI R R R7 R8 R9 R0 AI AI AI AI AI AI A0 A A A A A.V 0.W ZD.V 0.W ZD.V 0.W ZD.V 0.W ZD.V 0.W ZD.V 0.W ZD BC7 T BC7 T BC7 T BC7 T BC7 T BC7 T 0K R8 0K R0 0K R 0K R 0K R 0K R8 R7 R9 R R R R7 N8 D7 N8 D8 N8 D9 N8 D0 N8 D N8 D LEDRL LD LEDRL LD LEDRL LD LEDRL LD LEDRL LD LEDRL LD K R K R K R K R K R K R 8 9 0 00n C 00μ/-V C SK SK7 SK SK8 SK9 SK0 JP SK JP SK JP SK JP SK JP SK JP SK JP SK7 JP SK8 - AI AI AI AI AI AI - DI DI DI DI DI DI - V RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY RELAY TSCDH RY Schematic diagram
PCB - 0 -
Leds and how to use them Leds feature a specific voltage drop, depending on type and colour. Check the datasheet for exact voltage drop and rated current! Never connect leds in parallel How to Calculate the series resistor: Example: operate a red led (.7V) on a 9Vdc source. Required led current for full brightness: ma (this can be found in the datasheet of the led) Supply voltage (V) - led voltage (V) = series resistance (ohms) required current (A) 9V -.7V = 0 ohm 0.00A Required resistor power handling= voltage over resistor x current passed trough resistor (9V -.7V) x 0.00A = 0.0W closest value : use a k resistor a standard /W resistor will do the job open collector outputs An open collector output can be compared to a switch which switches to ground when operated LEDs in series: Example: x red led (.7V) on 9V battery Required led current for full brightness: ma (this can be found in the datasheet of the led) Example: How to switch an LED by means of an open collector output Supply voltage (V) - (number of leds x led voltage (V)) = series resistance (ohms) required current (A) 9V - ( x.7v) = 780 ohm 0.00A use an 80 ohm resistor
The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu Modifi cations and typographical errors reserved - Velleman nv. HKA0 IP Velleman NV, Legen Heirweg - 9890 Gavere.