Wheels, Tires, & Brakes Proudly Distributed By
Dual Flange Wheel Assemblies Chrome or polished stainless steel spokes are laced to chrome rims and hubs. The 16" wheel assemblies feature our Europeanmanufactured chrome 16" rims. The hubs feature thicker spoke flanges, and rotor flanges held to.001" runout with either 5/16" or 7/16" holes on both sides. All hubs accept any stock sprocket/rotor or rotor/rotor combination for greater flexibility when building custom wheel combinations. They include all internal spacers, seals and washers, and bearing end play is set at the factory. Wheel assemblies will bolt-on to most models from 73-85. Note: Wheels fit the rear of most models from 86-99 when installed with a CC #19722 spacer (OEM 40932-81) between the belt pulley or sprocket and the hub. Wheels with 7/16" Flange Holes 18687 16" x 3.00" with stainless steel spokes.................$399.99 Wheels with 5/16" Flange Holes 19675 16" x 3.00" with stainless steel spokes.................$379.99 18695 21" x 2.15" with stainless steel spokes.................$385.99 Front Axle Spacer for FXWG Models Replacement right or left axle spacers for FXWG models. May also be used when fitting other wheels (such as CC # s 19687 or 19694) to late model front ends.sold in packs of 5. 19696 80-83 left spacer (repl. OEM 41594-73)...................$3.60 19697 83 right spacer (repl. OEM 41607-83)....................$3.50 Chrome Dual Flange Wheel Hubs Complete chrome hub assemblies for the front or rear of most Harley- Davidson models from 73-99. 7/16" or 5/16" holes in both flanges, all internal components and bearing preload set at the factory. 19678 Front or rear hub with 7/16" holes in both flanges for models from 73-85 (repl. OEM 43540-73A).....................$159.99 19776 Rear hub with 7/16" Pulley /Sprocket side flange holes & 3/8" Brake Rotor side flange holes for models from 86-99 (repl. OEM 40976-86)......................................$164.99 19800 Front hub with 5/16" holes in both flanges (repl. OEM 43663-80A)................................................$189.99 19718 Rebuild kit (includes bearings, cones, seals, spacers, washers and retaining rings)...................................$29.99 26051 Timken bearing and cone (repl. OEM 9052)..............$9.99 26138 Bearing only...........................................$6.99 26137 Cone only.............................................$4.99 19682 Outer bearing spacers (repl. OEM 41196-73) sold in pairs..$7.99 54331 Rubber oil seals (repl. OEM 47519-58) pack of 10.........$1.30 54207 Rubber oil seal (repl. OEM 47519-83A) pack of 10.........$1.80 19684 Hub washers (repl. OEM 43559-73) sold in pairs...........$1.99 19685 Hub retainer rings (repl. OEM 11027) sold in pairs........$8.49 19686 Spacer 4.420" (repl. OEM 43601-78) Orange..............$7.99 19688 Spacer 4.434" (repl. OEM 43602-78) Yellow...............$7.99 19689 Spacer 4.448" (repl. OEM 43603-78) White...............$7.99 Belt Pulley and Sprocket Spacer This part was used on many Big Twin models from 80-85. It was most commonly used on belt drive models to achieve the proper spacing of the rear belt pulley to the wheel. This spacer is required for use on our rear wheels when used in many different applications. Fits Big Twin and Sportster models. 19722 Replaces OEM 40932-81...............................$10.49 U.S. Patent #4,880,280 64012 Wheels with Timken-Style Star Hubs for 36-66 Big Twins A wide selection of stock replacement and custom wheels with chrome or polished stainless steel spokes laced to our patented Star Hub with Timken-style bearings (CC #64012). Bearing preloads are set at the factory. These complete wheel assemblies fit the front or rear of most Big Twin models from 36-66 when the appropriate Custom Chrome Axle and Hardware kit is used. The stock brake axle sleeve for the appropriate application is also required. Though the Axle Kits will work with Original Equipment Star Hubs, the Original Equipment axles will not work with Custom Chrome Wheel Assemblies with Star Hubs. Complete Wheel Assemblies 18547 16" x 3.00" with stainless steel spokes.............. $399.99 18541 21" x 2.15" with stainless steel spokes.............. $389.99 Star Hub with Timken-Style Bearings 64012 Complete Star Hub assembly....................... $179.99 Axle and Hardware Kits 64057 Front for models from 36-48........................ $46.99 64058 Front for models from 49-66........................ $39.99 64066 Rear for models from 36-57......................... $49.99 64067 Rear for models from 58-66......................... $39.99 Replacement Spokes 08019 16" spoke set. Chrome............................. $42.99 08219 16" spoke set. Stainless steel....................... $109.99 08023 21" spoke set. Chrome............................. $45.99 08223 21" spoke set. Stainless steel....................... $139.99 08025 19" spoke set Chrome.............................. $42.99 08225 19" spoke set Stainless steel........................ $124.99 *New style lacing pattern. Replacement Parts 64002 Bearing spacer (2.410" orange) sold each............. $5.49 64087 Bearing spacer (2.424" yellow) sold each.............. $5.49 64003 Bearing and race (two complete sets)................ $20.99 64005 Bearing only (pair)................................. $13.99 23999 Steel oil seal (1.625" O.D.) pair....................... $3.99 64007 Chrome axle spacer (sold each)....................... $5.99 64008 Retaining ring (pair)................................. $2.99 19620 Outer cover without hole for zerk fitting (repl. OEM 43566-35TA).............................................. $8.99 19568 Hub cover screw/lockwasher kit (pack of 5)............ $4.99 TRAN.02 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
Front Wheel Assemblies for Sportster, Dyna Glide, FX and FXR Models from 77-99 Stock replacement and custom wheels with chrome or polished stainless steel spokes laced to a chrome hub and a 19" or 21" drop center rim with rolled edge. Wheel assemblies are available for most models from 77-99. All wheel assemblies are complete with axle spacer, seals and bearings which have had their preload set at the factory. For all Sportster, FX and FXR models with dual disc narrowglide front ends from 77-83 18711 19" x 2.50" with stainless steel spokes.................$385.99 18712 21" x 2.15" with stainless steel spokes.................$385.99 For all Sportster, Dyna Glide, FX and FXR models with single or dual disc narrowglide front ends from 84-99 18707 19" x 2.50" with stainless steel spokes.................$385.99 18708 21" x 2.15" with stainless steel spokes.................$385.99 Chrome Front Hubs Include the chrome hub and all of its internal components with properly spaced bearings. For all Sportster, FX and FXR models with dual disc narrowglide front ends from 77-83 19710 Complete hub assembly (repl. OEM 43600-78)..........$174.99 19714 Left bearing spacer (repl. OEM 43488-77)................$4.99 19715 Spacer 2.564" (violet) replaces OEM 43623-78............$6.99 19716 Spacer 2.550" (pink) replaces OEM 43624-78.............$6.99 19717 Spacer 2.536" (gold) replaces OEM 43625-78.............$6.99 19693 Rebuild kit (includes bearings, cones, seals, and left-hand spacer)...............................................$31.99 54332 Steel oil seal (repl. OEM 47519-72) pack of 10............$1.10 54207 Rubber oil seal (repl. OEM 47519-83A) pack of 10.........$1.80 26051 Timken bearing and cone (repl. OEM 9052)..............$9.99 *Note: Modifications to caliper pin and additional rotor spacers may be required for clearance. For Sportster, Dyna Glide, FX and FXR models (except FXLR) with single or dual disc narrowglide front ends from 84-99 19709 Complete hub assembly (repl. OEM 43619-84)..........$174.99 19585 Right bearing spacer (repl. OEM 43358-83)...............$4.99 19715 Spacer 2.564" (violet) replaces OEM 43623-78............$6.99 19716 Spacer 2.550" (pink) replaces OEM 43624-78.............$6.99 19717 Spacer 2.536" (gold) replaces OEM 43625-78.............$6.99 54332 Steel oil seal (repl. OEM 47519-72) pack of 10............$1.10 54207 Rubber oil seal (repl. OEM 47519-83A) pack of 10.........$1.80 26051 Timken bearing and cone (repl. OEM 9052)..............$9.99 Front Wheel Assemblies for Sportster and FX Models from 74-77 A selection of stock replacement and custom front wheels for all 74-77 Sportster and FX models (except 77 FXS and XLCR) with single disc narrow glide front ends. Available with either chrome or polished stainless steel spokes laced to a chrome hub and a 19" or 21" Drop Center rim with rolled edge. Each wheel assembly is complete with axle spacer, seals and bearings with their preload set at the factory. 18552 19" x 2.50" with stainless steel spokes.............. $359.99 18553 21" x 2.15" with stainless steel spokes.............. $344.99 Chrome Front Hub Assembly for Models from 74-77 A complete assembly including the chrome hub and all of its internal components with properly spaced bearings. Hub fits the front wheel on Sportster and FX models from 74-77 (except 77 FXS and XLCR). 19551 Complete hub assembly (repl. OEM 43600-74)....... $174.99 19583 2.166" center bearing spacer (repl. OEM 43745-73).... $5.99 19594 Left bearing spacer (repl. OEM 43548-74)............. $4.99 19693 Rebuild kit (includes bearings, cones, seals, and left-hand spacer)............................................ $31.99 54332 Steel oil seal (repl. OEM 47519-72) pack of 10......... $1.10 26051 Timken bearing and cone (repl. OEM 9052)........... $9.99 Chrome Rear Hub AssemblyRear Wheel Assemblies for Big Twins from 67-72 Complete wheel hub assembly includes the chrome hub and all of its internal components with properly spaced bearings. The hub fits the front or rear wheel of all FL models from 67-72 and the rear of FX models from 71-72. 19554 Complete hub assembly (repl. OEM 43540-67A)...... $185.99 19559 Bearing spacer (repl. OEM 43549-67).................. $4.99 19560 Bearing locknut (repl. OEM 43542-67)................ $8.99 19562 Hub spacer (repl. OEM 41196-55)..................... $3.99 54324 Rubber oil seal (repl. OEM 41210-55) Sold in packs of 10................................................... $1.30 26133 Hub bearing (repl. OEM 43577-67)................... $29.99 www.customchrome.com TRAN.03
08007 40-Spoke Extra-Wide Offset Dual Flange Rear Hubs Pulley side is offset.875" further out than standard 73-85-style hubs. Eliminates the need for pulley spacers on most applications, and places the bearings farther apart for greater stability. Helps to eliminate bent axles often associated with using standard hubs for wide applications using large pulley spacers. 19543 Sold each...........................................$179.99 688056 16" Drop Center Rim 3"-wide drop-center rim to fit 5.00/5.10 x 16" motorcycle tires. 08007 Chrome 40-hole rim (repl. OEM 43007-40A).............$78.99 688056 Black 40-hole rim (repl. OEM 43007-40A)................$72.99 15940 56410 15942 08776 Custom Chrome Rims These 40-hole drop center rims are formed from a high-strength steel alloy and given a coating of show-quality chrome that will stay looking great for years. They re the finest stock replacement rims available anywhere. Lace them with our twisted spokes for a truly custom look! 56410 16" x 3.00" for use with steel hubs used from 81-96 (replaces OEM 43085-81)MCV..................................$129.99 08776 18" x 5.75" for custom applications....................$149.99 Note: The CC #56410 16" x 3.00" rim requires the use of a metal center valve tube (CC #1571517). Chrome Front Rims 19" Rim Exclusive to Custom Chrome. This show-chromed 19" x 2.50" Rolled- Edge drop center rim is styled like the classic drop center, and the rolled edge gives your front wheel additional strength. Another first for this rim is the duplication of the OEM spoke dimple pattern which permits effortless lacing to disc wheel hubs. 15940 Replaces OEM 43018-73...............................$85.99 21" Rim This show chrome drop center rim with a fully-rolled edge is the same size (21" x 2.15") and has the same spoke pattern as the Original Equipment 21" rim. 15942 Replaces OEM 43662-80B..............................$95.99 TRAN.04 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
08250 Custom Chrome Spoke Sets Custom Chrome s spoke sets use nothing but the best 6/8 gauge carbon and polished stainless steel materials, but we ve put a new twist on them for a great custom look. Flat spokes are our regular spokes with the body rolled for a flattened profile. Add a few twists for the great-looking twisted sets that create wheels that throw light in all directions in a kaleidoscope of colors and highlights. Flat, twisted and regular round spokes come in polished stainless steel and chrome-plated carbon steel sets. Tips On Choosing Spokes On the following pages are the variety of stock and custom rims and hubs available from Custom Chrome or Harley-Davidson. Use the illustrations to determine hub and rim combination, then select the spoke set to complete your wheel. For example: an aluminum 74-77 front hub for FX models laced with Twisted stainless steel spokes to a chrome 21" Akront drop center aluminum rim for an FXWG (shown in illustration J ), uses CC #08215 spoke set. The rim illustration guide shows basic rim shape, and position of the spoke holes in relation to each other. This should help identify the rim you have or want to buy. 08252 Replacement Spoke Nipples (6mm Square) 08250 Set of chrome nipples (42) extralong..................... $0.30 08253 Set of stainless steel nipples (42) extra-long................ $0.76 08252 Set of chrome nipples (42) stocklength................... $0.27 08251 Set of stainless steel nipples (42) stock-length.............. $0.74 Easy Reference Spoke Chart Replacement Spokes with Nipples for Most Stock-Style 40-Spoke Wire Wheels For Steel Dual or Single Flange Front or Rear Hubs: 08019 16" spoke set. Chrome...............$42.99 08219 16" spoke set. Stainless steel........$109.99 08012 16 Twisted spoke set. Chrome.......$84.99 08212 16 Twisted spoke set. Stainless steel $159.99 08025 19" spoke set Chrome...............$42.99 08225 19" spoke set Stainless steel.........$124.99 08013 19 Twisted spoke set. Chrome.......$89.99 08213 19 Twisted spoke set. Stainless steel $149.99 08023 21" spoke set. Chrome.........$45.99 08223 21" spoke set. Stainless steel.. $139.99 08014 21 Twisted spoke set. Chrome $97.99 08214 21 Twisted spoke set. Stainless steel............................ $179.99 For Aluminum Front Hubs* : 08042 19" spoke set Chrome*........ $47.99 08242 19" spoke set Stainless steel*.. $139.99 08016 19 Twisted spoke set. Chrome* $89.99 08026 21" spoke set. Chrome*........ $45.99 08226 21" spoke set. Stainless steel* $139.99 08015 21 Twisted spoke set. Chrome $99.99 Part #19544 Hub Spokes for Sportster Models with Rear Spool Hub When used with any of the six spoke sets listed below, this rear hub will fit any Sportster or K model (except XLCR) from 55-78. For all steel 15" drop center rims (rim illustration E ) Chrome Price Stainless Price 08048 $37.99 08248 $112.99 Round spoke set For all steel 16" drop center rims (rim illustration E ) Chrome Price Stainless Price 08019 $42.99 08219 $109.99 16" spoke set. Chrome Fits all steel 18" drop center rims (rim illustration E ) Chrome Price Stainless Price 08029 $42.99 08229 $125.99 Round spoke set Spokes for Sportster and FX Models with Front Drum Hub For Sportster or FX models from 64-72. Fit OEM 43002-70 steel 19" drop center rims (rim illustration H ) Chrome Price Stainless Price 08028 $47.99 08228 $119.99 Round spoke set Fit all steel 19" custom rims (rim illustration F ) and 19" Akront aluminum rims Chrome Price 08040 $46.99 Round spoke set Fit all steel 21" custom and drop center rims (rim illustrations F and J ) and 21"Akront aluminum rims Chrome Price 08041 $42.99 Round spoke set Rim Illustrations Illustration E Illustration F Illustration G Illustration H Illustration J www.customchrome.com TRAN.05
17936 19672 17938 17929 19686 17934 Late Model Wheel Hub Spacers and Bearing Shims These parts are accurate reproductions of the Original Equipment pieces used on 5-speed Dresser models from 82-99, and most other models from 92-99. Installing them in your wheels will permit you to set your wheel bearing end play tighter, resulting in improved rideability with better cornering and less straight-line weaving. Hub Spacers Sold each. 17929 2.424" spacer for narrow hub (repl. OEM 43613-92).......$3.99 17938 4.308" spacer for wide hub (repl. OEM 43608-82).........$8.99 17936 Wheel bearing spacer washer (repl. OEM 43650-82).......$4.99 Wheel Bearing Shims Sold in packs of 10. 17931.032" shim (repl. OEM 43290-82).........................$1.00 17932.016" shim (repl. OEM 43291-82).........................$1.00 17933.008" shim (repl. OEM 43292-82).........................$1.00 17934.004" shim (repl. OEM 43293-82).........................$1.00 17935.002" shim (repl. OEM 43294-82).........................$1.00 140006 19715 Wheel Bearing Spacers Just what you need to redo the bearings on your hub. Available in different lengths. Sold each. Steel Dual Flange Hub Spacers 19686 Spacer 4.420" (repl. OEM 43601-78) Orange..............$7.99 19688 Spacer 4.434" (repl. OEM 43602-78) Yellow...............$7.99 19689 Spacer 4.448" (repl. OEM 43603-78) White...............$7.99 Cast Wheel Hub Spacers 19672 4.420" (repl. OEM 43604-78) red........................$7.99 19673 4.434" (repl. OEM 43605-78) yellow.....................$7.99 19674 4.448" (repl. OEM 43606-78) white......................$7.99 Aluminum Front Hub Spacers 56241 2.148" (repl. OEM 43635-74) gold and violet.............$7.99 56239 2.162" (repl. OEM 43633-74) red and white..............$7.99 19583 2.166" center bearing spacer (repl. OEM 43745-73).......$5.99 56240 2.177" (repl. OEM 43634-74) green and orange...........$7.99 19717 Spacer 2.536" (gold) replaces OEM 43625-78.............$6.99 19716 Spacer 2.550" (pink) replaces OEM 43624-78.............$6.99 19715 Spacer 2.564" (violet) replaces OEM 43623-78............$6.99 54331 54332 54324 54207 Wheel Seals Fits the spoked rear wheels on 55-78 Sportster and K models; 67-72 FLs and 71-72 FXs. 54324 Rubber oil seal (repl. OEM 41210-55) Sold in packs of 10...$1.30 140006 Steel oil seal (repl. OEM 41210-55) Sold in packs of 5......$1.20 Fits the spoked rear wheel on FLs, FXs and FXRs from 73-83 and XLs from 79-83; spoked front on FLs and FXWGs 80-83; cast front or rear on FLs 80-84; cast front or rear (brake side only) on FLTs and FLHTs from 82-84. Also fits the swingarm on all Big Twin drum brake models from 58-72. 54331 Rubber oil seals (repl. OEM 47519-58) pack of 10.........$1.30 Fits the cast rear and spoked or cast front wheels on FXs (except FXWG), FXRs and XLs from 73-83; cast front and rear wheels on FLs from 73-79; cast rear wheel (sprocket side only) on FLT/FLHT from 80-83 Also fits the swingarm on 4-speed FX Big Twin disc brake models from 73-86. 54332 Steel oil seal (repl. OEM 47519-72) pack of 10............ $1.10 Fits the cast or spoked front and rear wheels on most models from 83-99. 54207 Rubber oil seal (repl. OEM 47519-83A) pack of 10.........$1.80 19718 19693 Wheel Hub Rebuilding Kits Contains all of the necessary bearings, seals and spacers to rebuild either cast wheels or aluminum front hubs. Fit Sportster, FX and FXR models from 73-83, or the steel dual-flange wheels on most models from 73-82. 19693 Aluminum hubs and front mag wheels.................$31.99 19718 Steel dual-flange hubs.................................$29.99 TRAN.06 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
19517 19580 19620 19570 19572 19575 19577 19568 19581 19571 19569 19573 19574 19576 19582 19579 Original Equipment-Style Star Hub Replacement Parts 19569 Thrust bearing sleeve (repl. OEM 43556-35)..................................................................................... $15.99 19570 Thick thrust washers (repl. OEM 43563-35) 5 pair................................................................................. $2.20 19571 Adjusting shims (.002") repl. OEM 43560-35 (pack of 50).......................................................................... $0.44 19572 Retainer and rollers (repl. OEMs 24721-30, 9220A)............................................................................... $15.99 19573 Inner thrust washer (repl. OEM 43552-39) pack of 10.............................................................................. $1.50 19574 Bearing collar (repl. OEM 43561-39)............................................................................................. $6.99 19575 Roller bearing sleeve (repl. OEM 43550-35)...................................................................................... $32.99 19576 Brake side retainer and rollers (repl. OEMs 43578-35, 9220A)..................................................................... $17.99 19577 Brake side thrust washers (repl. OEM 43558-39) pack of 10........................................................................ $0.80 19579 Thrust washer lockring (repl. OEM 43554-35) 5 pair............................................................................... $0.90 19580 Brake side cork washer retainers (repl. OEM 43564-35) pack of 25.................................................................. $0.52 19581 Small cork washer (repl. OEM 43570-35) pack of 10............................................................................... $1.00 19517 Gasket and cork washer kit (repl. OEMs 43570-35, 43571-35, 43576-31)................................................................... $2.99 19582 Large brake side cork washers (repl. OEM 43571-35) pack of 10.................................................................... $1.30 19620 Outer cover without hole for zerk fitting (repl. OEM 43566-35TA).................................................................. $8.99 19568 Hub cover screw/lockwasher kit (pack of 5)....................................................................................... $4.99 6"-Long Stainless Steel Wheel Spacer Stock Make your own custom wheel spacers! Stainless steel is rust free! No chrome plating required as with spacers machined from plain steel. Simply cut-to-length and use! 501142 Fits many 3/4"-diameter axle applications (6"-long x 3/4" ID x 1 1/8" OD) $36.99 Star Hub Cover Kit Includes the chrome outer cover, inner cover with grease fitting, gasket and corks, screws and lockwashers. 19578 Fits Star Hubs from 36-66...............$17.99 19698 19699 Axle Sleeves for Star Hubs 19698 Front axle sleeve (brake side) for Big Twins from 49-66 (repl. OEM 43882-48)................................................................. $23.99 19699 Left rear axle sleeve for Big Twins from 36-57 (repl. OEM 41600-36)... $23.99 140350 Hub Rebuild Kits Hub rebuild kits for most Big Twin and Sportster models 36-99 with steel or aluminum hubs. Available with or without bearings, these kits include seals, bearing spacers, center spacers (between bearings) snap rings, washers and gaskets necessary to rebuild the specific hubs listed. Note: Kits do not contain outer axle spacers. With Bearings Price Without Bearings Fits dual flange hubs front and rear on FL models 73-83, front FXWG 80-84 and rear FX models 73-82. Contains 4.434" (yellow) center spacer Price 140350 $34.99 140349 $13.99 www.customchrome.com TRAN.07
I H G F K A Chrome-Plated Front Axles The greatest selection of chrome axles in the industry. Complete assemblies for models as far back as 36. Fully-chromed, including the hardware. Axle shafts are machined from heat-treated chrome moly steel, triple-step chrome-plated, then machine-polished and ground to a finish size tolerance of ±.0005". Axles are available individually or packaged complete with a fully-chromed hardware kit. Photo shows contents of hardware and axle kits as well as the basic axle profile. ILLUS APPLICATION Replaces Axle OEM# Axle Only Price Hardware Only Price Hardware & Axle Kit A Fits EL, FL and UL from 36-48 43872-36 64013 $29.99 64072 $14.99 64057 $46.99 B Fits FL models from 67-71 43875-67 64053 $29.99 64073 $8.99 64059 $32.99 C Fits EL and FL from 49-66 43875-48 64018 $29.99 64073 $8.99 64058 $39.99 D Fits 4-speed FL models from 73-80, and FXWG from 80-83 43875-73 64029 $29.99 64075 $11.99 64060 $32.99 E Fits FL 81-84; FXST, FXSTC, and FXDWG 84; FXWG 84-86; FLT, FLHT, FLHS models 83-99 43346-83 64037 $29.99 64076 $14.99 64061 $35.99 F Fits Sportster, FX and K models from 52-72 43871-52 64054 $29.99 n/a 64062 $28.99 G Fits Sportster and FX models with single disc brake from 73-77 43871-73 n/a 64078 $9.99 64063 $31.99 H Fits Sportster, FX and FXR models with dual disc 64064 43883-77 64049 $29.99 64078 $9.99 brake from 77-83 $31.99 I Fits Sportster, FX and FXR models with 35mm forks from 84-87 43883-84 64089 $29.99 64078 $9.99 64065 $30.99 K Fits FL Softail models 86-99 41584-86A 64099 $29.99 64100 $21.99 64101 $50.99 E D C B Price TRAN.08 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
D E F G H A B C Chrome-Plated Rear Axles The greatest selection of chrome axles in the industry. Complete assemblies for models as far back as 36. Fully-chromed, including the hardware. Axle shafts are machined from heat-treated chromemoly steel, triple-step chrome-plated, then machine-polished and ground to a finish size tolerance of ±.0005". The rear axle nuts are attached to the shaft with a full-penetration weld, then machined smooth before final machine-polishing and plating. Axles are available individually or packaged complete with a fully-chromed hardware kit. Photo shows contents of hardware and axle kits as well as the basic axle profile. ILLUS.. APPLICATION Replaces Axle OEM# Axle Only Price Hardware Only Price Hardware & Axle Kit A Fits EL, FL and UL from 36-57 41552-36 64021 $29.99 64081 $18.99 64066 $49.99 B Fits FL models from 58-66 41552-58A 64027 $29.99 64082 $18.99 64067 $39.99 C Fits FL and FX models from 67-72 41552-67 64051 $29.99 64083 $18.99 64068 $41.99 D Fits 4-speed FL and FX models with rear chain drive from 73-85 41552-73 64039 $29.99 64084 $11.99 64069 $35.99 E Fits 4-speed FL and FX models with rear belt drive from 80-86 41580-79 64046 $29.99 64085 $10.99 64070 $33.99 F Fits Sportster and K models from 52-E 78 41551-52 64043 $29.99 64086 $13.99 64071 $35.99 G Fits Sportster models from 79-03 41563-77A 64090 $29.99 64091 $13.99 64094 $46.99 H Fits all FXR models from 82-94 41110-79A 64095 $29.99 64096 $10.99 64098 $42.99 H Fits all Softail models from 86-06 41110-79A 64095 $29.99 64085 $10.99 64108 $39.99 H Fits all FLT/FLHT/FLHS/FLHR models from 87-01 41110-79A 64095 $29.99 n/a n/a Price www.customchrome.com TRAN.09
CC Pyramid Axle Adjusters Forged steel axle carriers are machined to close tolerances to be a snug fit inside the swingarm section eliminating the common problem of swingarm distortion when axle nuts are overtightened. The chrome end caps are made of diecast aluminum and the chrome-steel nuts have a long shank tapped to permit a full range of axle adjustment. They fit all CC chrome 4-speed swingarms as well as the stock swingarms on Sportster models from 79-03 and 73-86 4-speed FL and FX models. They also fit 86 Softail models. Include instructions. Sold in pairs 31112 Replaces OEM 41532-89T..............................$49.99 Chrome Axle Adjuster End Caps Add a beautiful chrome-plated highlight to the ends of your swingarm. Die-cast construction won t distort like the Original Equipment stamped steel plates. Work with your stock axle carriers and increase the range of adjustment. Fit 4-speed Big Twins from 73-86 and Sportster models from 79-96. 31108 Sold in pairs..........................................$18.99 15131 26196 12949 Chrome Rear Wheel Adjusters Choose the rear wheel adjuster for your motorcycle from the selection below. Each kit comes complete and is beautifully chromeplated.sold in pairs. 15131 Fit Sportster and K models from 54-78 (repl. OEM 41531-84T).....................................................$14.99 12949 Fit Big Twin models from 36-72 (repl. OEMs 41576-36, 7800W).....................................................$11.99 26196 Fit all Big Twin models (except Dyna Glide and 87-01 Softail models) from 73-01 and Sportster models from 79-03 (repl. OEM 41530-84T)......................................$16.99 Tire Tubes and Rim Strips A wide section of sizes from quality manufacturers Extra-Wide Inner Tubes The solution for extra-wide tires that require tubes. Butyl rubber construction for good air retention, carefully molded for uniformity. Center valve stem. 07034 200/60 x 16" for use with 180 x 16" and 200 x 16" extra-wide tires.................................................$31.99 07035 180/55 x 18" for use with 170 x 18", 180 x 18" and 200 x 18" extra-wide tires......................................$26.99 629415 200/55 x 17 for use with 200 x 17 wide tires...........$37.99 Imported Tubes 1571515 130-140/90 x 15" Metal Center Valve..................$19.99 1571517 120-130/90 x 16" Metal Center Valve..................$23.99 1571064 5.00"-5.10" x 16" Rubber Side Valve..................$23.99 1571072 5.00"-5.10" x 16" Metal Side Valve....................$23.99 1571520 120-130/90 x 17" Metal Side Valve....................$19.99 1571523 140/90 x 18" Metal Center Valve......................$29.99 1571129 2.75"-3.00" x 19" Metal Center Valve.................$11.49 1571177 3.25"-3.50" x 19" Rubber Center Valve................$12.99 1571144 2.75"-3.00" x 21" Metal Center Valve.................$12.49 1571145 3.25"-3.50" x 21" Metal Center Valve.................$16.49 Extra-Wide Rim Strips 07013 16" center valve (3.1"- wide)............................$2.99 07014 18" center valve (2"-wide)..............................$2.99 Rim Strips 07017 16" side valve..........................................$1.49 07022 16" center valve.......................................$1.49 07019 18" center valve.......................................$1.49 07020 19" center valve.......................................$1.49 07021 21" center valve.......................................$1.49 TRAN.10 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
Speedmaster MK2 AM6 Long lasting, positive steering tire for front wheel fitment only. S Rated for speeds up to 112 mph. Ribbed pattern for classic look. Unique for long life and even wear. Manufactured from a cling rubber. Excellent lateral stability and high mileage. Speedmaster Bias (TT) 1011288 3.25"-19" Blackwall..................................$139.99 1011291 3.50"-19" Blackwall..................................$141.99 1011299 3.00"-21" Blackwall..................................$141.99 SM MK II AM7 The high mileage, high profile tire for rear fitment. Perfect for Harley riders or those seeking traditionally styled tires. S Rated for speeds up to 112 mph. Center rib, flanked by interlocking studs. Cling rubber compound for excellent wet road adhesion. SM MK II AM7 Bias (TT) 1011306 5.00" -16"....................................... $221.99 Gangster The Gangster has all the features of Avon s popular Universal, with the added look of a 2 3/4 wide, white sidewall. A perfect tire for classics and restorations, the Gangster features state-of-the-art rubber compound, blending performance and vintage style. Tubeless construction. Front and rear application. Gangster Bias (TL) 1011241 MT90H-16" Wide Whitewall..........................$356.99 MOTORCYCLE TIRE SIZE CONVERSION CHART FRONT TIRES METRIC ALPHA INCH 80/90 MH90 2.50/2.75 90/90 MJ90 2.75/3.00 100/90 MM90 3.25/3.50 110/90 MN90 3.75/4.00 120/80 4.25/4.50 120/90 MR90 4.25/4.50 130/90 MT90 5.00/5.10 REAR TIRES METRIC ALPHA INCH 110/90 MP85 4.50/4.75 120/90 MR90 4.50/4.75 130/80 5.00/5.10 130/90 MT90 5.00/5.10 140/80 5.50/6.00 140/85 MU85 5.50/6.00 140/90 MU90 5.50/6.00 150/80 MV85 6.00/6.25 150/90 MV85 6.00/6.25 www.customchrome.com TRAN.11
Rear Brake Caliper Kit This kit includes a CC #13012 deluxe chrome single action rear brake caliper, complete with brake pads, mounting bolts, bleeder valve and all internal components. 130501 10" disc brake kit....................................$369.99 4541337 Ferodo 'P compound pad.............................$35.99 8009003 Motor Factory Organic pad set.........................$22.99 12435 Brake MAX pad set..................................$11.99 Rear Brake Calipers Precision-engineered calipers are made of die-cast aluminum that is polished and then chrome-plated or painted wrinkle black. Perfect replacements for the stock unit on Softail, FXR, Sportster, and Dyna Glide models from late 87-99 (replaces OEM 44050-87). 13022 Chrome.............................................$169.99 13030 Black wrinkle........................................$159.99 4541661 Ferodo 'P compound pad set..........................$35.99 8009004 Motor Factory Organic pad set........................$28.99 26484 26483 Complete kit 91484 Rear Brake Caliper Assemblies Chrome-plated, or durable powder-coated replacement rear brake calipers for 4-speed Big Twin models from 73-83. Compatible with either the boomerang support bracket (used as Original Equipment thru 80), or the later Y bracket used from 80-83. Complete with late model square section O-rings and seals, and mounting bushings and pins. Completely rebuildable with Original Equipment or CC parts. 13012 Chrome.............................................$289.99 13017 Gloss black powder coat..............................$269.99 4541337 Ferodo 'P compound pad.............................$35.99 8009003 Motor Factory Organic pad set.........................$22.99 12435 Brake MAX pad set..................................$11.99 Rear Brake Rebuild Kit This kit contains all the parts necessary to repair worn, rattling banana style rear calipers on FL and FX models 73-80. Complete as shown, including an oversized pin to repair badly worn (oval) caliper through holes. 91484 Complete kit (includes hardware kit)...................$87.99 26406 Mounting kit. Fits FL and FX models 73-80..............$19.49 26483 Chrome steel brake anchor. Replaces OEM 44154-73T....$12.99 26484 Mounting bracket only (Includes bushings). Replaces OEM 44166-73.............................................$32.99 12435 Brake MAX pad set..................................$11.99 Disc Rotor Spacer.040"-thick spacer is used to re-establish correct rotor-to-caliper alignment and spacing whenever servicing wheels, brake calipers, supports or rotors on Original Equipment disc brake systems from 73-84. Sold each 25635 Replaces OEM 41814-76................................$6.99 TRAN.12 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
26320 26321 Caliper Mounting Stud and Pin Kit Includes brake pad pins, mounting bracket steel pin bushings, mounting stud, locknut and washer for OEM and CC banana calipers from 73-80. 25558 Complete kit (repl. OEM 44331-73) sold each....................$19.99 25190 Pins only (repl. OEM 44124-72) card of 5 pairs.....................$1.40 25913 Large steel pin bushing (repl. OEM 45821-75) sold each...........$3.99 25914 Small steel pin bushing (repl. OEM 45822-74) sold each...........$2.99 Heavy-Duty Rear Caliper Support Spring Reduces rear caliper rattle and mounting pin wear on boomerang supported, Big Twin rear brake calipers from 73-80. Chromed bracket fits easily over the axle so the chromed support spring places steady upward pressure against the caliper. 26320 Sold each....................$8.99 Standard Caliper Support Complete with bracket, spring and button. Fits all rear banana calipers from 73-80. 26321 Sold each...................$11.99 Dual Disc Caliper Bolt Kit Contains 4 chrome sockethead shoulder bolts and nuts. Designed to mount the front dual disc brake calipers on FX, FXR, FXWG and XL models 77-83. Set of 4. 25210 Replaces OEMs 44173-77, 44174-77............................$29.49 28136 25494 26319 26318 25520 Caliper Mounting Bushings This set of American-made caliper mounting bushings will fit all dual disc fork legs from 77-83. Set of two. 25910 Replaces OEMs 46018-77, 46019-77.............................$6.99 13036 Caliper Mounting Y Brackets For 10" Rotor Systems Patterned after the later 11 1/2" caliper support used from 81-83, these unique brackets provide improved support and alignment for 10" rotor systems. Fit all Big Twin rear discs from 73-80. 13036 Chrome....................$129.99 Rear Brake Caliper Anchor Kit Includes the clevis pin, washer, and cotter pin. Fits all FXs from 81-82 and 83 FXE (replaces OEMs 520W, 36718, and 40919-81) 26305 Bag of 5 kits..................$5.00 Brake Caliper Piston Assemblies Rear 28130 Fits FL and FX models from 73-E80 (repl. OEM 44129-73).........$46.99 28135 Fits FL models from 81-84 and FLT or FLHT models from 80-85 (repl. OEM 43946-79) Includes boot and seal. Two required per caliper......$19.99 28132 Fits late 80 FL models, all FX models from late 80-82, and 83 FXE (repl. OEM 44118-80)..............$19.99 Front 28131 Fits FL models from 72-80 (repl. OEM 44109-72A).............$46.99 28132 Fits FL models from late 80-84 (repl. OEM 44118-80)..............$19.99 28133 Fits all single disc Sportster and FX models from 74-77 (repl. OEM 44275-74)...................$19.99 28140 Fits all dual disc Sportster, FX and FXR models from 77-83. Includes the piston, seal and rubber dust boot (repl. OEM 44157-77).........$21.99 Caliper Mounting Pin Rebuild Kit Restores banana calipers to safe service when the caliper support pin has enlarged and egg-shaped the thru-hole in the caliper body. Kit includes a 3" support shaft, hardened washers and two sockethead screws. 25555 Fits all banana calipers 72-83..........................$10.99 www.customchrome.com Brake Fittings and Bleeder Screws Wheel Cylinder Swivel Fitting 26318 Fits all Big Twins from 58-62 (repl. OEM 41745-58) sold each.. $19.99 Wheel Cylinder Bolt 26319 Fits all Big Twins from 58-72 (repl. OEM 41743-58) sold each... $6.99 Bleeder Screws Fits the rear wheel cylinder on all FL and FX models from 58-72; the FL sidecar wheel cylinder from 58-E70; the pieshaped front caliper on all Sportster and FX models from 74-77; the banana caliper on the front and rear of all FL models from 72-79; the banana caliper on the front of 73 Sportster and FX models; the banana caliper on the rear of all FX models from 73-77. Replaces OEM 41749-58. 25494 Bleeder screws (repl. OEM 41749-58) pack of 10............. $1.20 Fits the front calipers of all dual-disc FX, FXR and Sportster, models from 77-83 and FLT/FLHT models from 80-83; the banana caliper and the dual piston caliper on the rear of all FL, FLT and FLHT models from 80-86; the banana caliper on the rear of all FX models from 78-83; the rear caliper of all Sportster models from 77-81; the Hayes rear brake caliper used from 86-03. Replaces OEM 44146-77. 25520 Pack of 10................. $1.30 25554 Chrome-plated (sold each).. $5.99 Brake Caliper Bleeder Screw Repair Kit Has an oversize bleeder screw and seat for banana caliper or drum brak 28136 Complete kit.............. $4.99 TRAN.13
19050 19052 Chrome Rear Brake Backing Plates These backing plates are accurate reproductions of the obsolete and difficultto-find Original Equipment parts. They fit all Big Twin models with hydraulic rear brakes from 58-72 and come complete with brake shoe retaining clips as well as the necessary chrome mounting hardware. 19050 58-62 models (replaces OEM 41650-58)........................ $84.99 19052 Chrome backing plate. Fits Big Twin models 63-72. Replaces OEM 41650-63..........................$79.99 Note: Although every effort has been made to produce a cosmetically perfect part, because of the complexities of polishing these backing plates prior to plating, the chrome may appear to be flawed in some small areas. Brake Linings Replacement brake shoe linings for Original Equipment drum brakes. Includes Rivets. Sold in pairs. 12440 Fit the rear of 38-57 Big Twins with 1 7/16"-wide linings(replaces OEM 41848-38)...................$14.99 12441 Brake linings with rivets. Fits Big Twin rear 58-62 and sidecar 58-up. Replaces OEM 41802-58. Sold in pairs........................$19.99 12443 Brake linings with rivets. Fits Big Twin rear 63-72. Replaces OEM 41808-63. Sold in pairs........$19.99 12439 Brake shoe linings with rivets. Fits front on FL models 49-71 and XL models 54-63. Also fits rear on XL models 54-78. Replaces OEM 44432-54A. Sold in pairs............$14.99 Accel Rear Brake Wheel Cylinders and Rebuild Kits Quality assemblies featuring precisionmachined rugged cast steel housings, heavy-duty rubber cups and seals, and a unique compression spring that eliminates cup extenders. Fits Big Twin rear brake models from 58-72. Wheel Cylinder 25495 58-62 (repl. OEM 41740-58)..$59.99 Rebuild Kits 25522 63-72 (repl. OEM 41748-63)...$29.99 25494 Bleeder screws (repl. OEM 41749-58) pack of 10................$1.20 Chrome Brake Drums with Sprockets 19055 Chrome brake drum with sprocket. Fits Big Twin models 36-57. Replaces OEM 41400-37*.............$143.99 19057 Brake drum with sprocket. Chrome. Fits Big Twin models 58-62. Replaces OEM 41400-58C*...........$149.99 19059 Brake drum with sprocket. Chrome. Fits Big Twin models 63-66. Replaces OEM 41400-63*.............$149.99 19061 Brake drum with sprocket. Chrome. Fits Big Twin models 67-72. Replaces OEM 41400-67*.............$193.99 19063 Fits Sportster models from 54-78 (except XLCR) repl. OEM 41401-52...........................$149.99 Brake Shoes Brake shoes with linings for models with Original Equipment drum brakes from 49-78. Sold in pairs. Front Brake Shoes 17386 Fit Sportster and K models from 54-63 and all Big Twins from 49-71 (replaces OEM 44401-49TB)...$36.99 Rear Brake Shoes 12606 Brake shoes. Fits Big Twin rear 38-57. Replaces OEM 41805-38. Sold in pairs......................$36.99 19319 Brake shoes. Fits Big Twin rear 58-62 and sidecar 58-97. Replaces OEM 41801-58A. Sold in pairs......$27.99 19312 Brake shoes. Fits Big Twin rear 63-72. Replaces OEM 41801-63. Sold in pairs............................$29.99 17386 Fit Sportster and K models (except XLCR) from 54-78 (replaces OEM 44401-49TB).................$36.99 TRAN.14 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
WHEELS, TIRES & BRAKES 130481 56404 56405 26319 19068 12432 19996 130323 130624 12443 12441 130361 12606 19055 12433 130367 130368 12434 19052 19057 19059 19061 19522 Mechanical Brake Parts 36-57 130369 19319 19312 19522 Hydraulic Brake Parts 58-72 Listed below in CC part number order. 12441 Brake linings with rivets. Fits Big Twin rear 58-62 and sidecar 58-up. Replaces OEM 41802-58. Sold in pairs $19.99 12443 Brake linings with rivets. Fits Big Twin rear 63-72. Replaces OEM 41808-63. Sold in pairs $19.99 19052 Chrome backing plate. Fits Big Twin models 63-72. Replaces OEM 41650-63 $79.99 19057 Brake drum with sprocket. Chrome. Fits Big Twin models 58-62. Replaces OEM 41400-58C* $149.99 19059 Brake drum with sprocket. Chrome. Fits Big Twin models 63-66. Replaces OEM 41400-63* $149.99 19061 Brake drum with sprocket. Chrome. Fits Big Twin models 67-72. Replaces OEM 41400-67* $193.99 19312 Brake shoes. Fits Big Twin rear 63-72. Replaces OEM 41801-63. Sold in pairs $29.99 19319 Brake shoes. Fits Big Twin rear 58-62 and sidecar 58-97. Replaces OEM 41801-58A. Sold in pairs $27.99 19522 Chrome brake drum mounting bolts. Fits Big Twins 41-72. Replaces OEM 43530-35A. Sold in 5 pack $14.99 19996 Brass 2-piece rear wheel cylinder swivel fitting. Fits Big Twin models 58-72. Replaces OEM 41750-63 $24.99 26319 Rear wheel cylinder bolt. Fits rear brake swivel on FL models 58-72. Replaces OEM 41743-58. Sold each $6.99 130323 Copper crush washers. Fits rear brake swivel bolt on Big Twins 58-72. Replaces OEM 41744-58. Sold in 10-packs $0.80 130367 Return spring, brake shoe upper. Fits Big Twins 58-62. Replaces OEM 41836-58. Sold in 5-packs $4.00 130368 Return spring, brake shoe upper. Fits Big Twins 63-72. Replaces OEM 41836-63. Sold in 5-packs $4.00 130369 Return spring, brake shoe lower. Fits Big Twins 63-72. Replaces OEM 41837-63. Sold in 5-packs $4.00 130481 Bleeder valve, 1/4". Fits Big Twins 58-72. Replaces OEM 4174958. Sold in 10-packs $1.60 *Note: Chrome must be removed from inside drum before installation to prevent damage to linings. Listed below in CC part number order. 12432 Chrome lever, brake cam. Fits Big Twin models 36-57. Replaces OEM 41929-39 $15.99 12433 Chrome lever, single hole (left side). Fits Big Twin models 36-57. Replaces OEM 42556-36 $12.99 12434 Chrome lever, double hole (right side). Fits Big Twin models 36-57.Replaces OEM 42560-37 $13.99 12606 Brake shoes. Fits Big Twin rear 38-57. Replaces OEM 4180538. Sold in pairs $36.99 19055 Chrome brake drum with sprocket. Fits Big Twin models 36-57. Replaces OEM 41400-37* $143.99 19068 Chrome lever, brake cam. Fits XL models 54-72. Replaces OEM 44307-52 $15.99 19522 Brake drum mounting bolts. Chrome. Fits Big Twin models 36-72. Replaces OEM 43530-35. Sold in 5 pack $14.99 130361 Clevis, brake rod. Chrome. Fits Big Twin models 35-57. Replaces OEM 42273-30 $9.99 *Note: Chrome must be removed from inside drum before installation to prevent damage to linings. 26056 12439 130317 130380 19530 19053 19522 140358 17386 140359 Front Drum Brake Parts (Left Side Brake) Listed below in CC part number order. 12439 Brake shoe linings with rivets. Fits front on FL models 49-71 and XL models 54-63. Also fits rear on XL models 54-78. Replaces OEM 44432-54A. Sold in pairs $14.99 17386 Brake shoes. Fits front on FL models 49-71 and XL models 54-63. Also fits rear on XL models 54-78. Replaces OEM 44401-49TB. Sold in pairs $36.99 19053 Chrome brake drum. Fits FL models 67-71. Replaces OEM 44111-67* $149.99 19522 Chrome brake drum mounting bolts. Fits FL models 41-72. Replaces OEM 43530-35A. Sold in 5 pack $14.99 19530 Chrome brake drum. Fits FL models 49-66. Replaces OEM 44111-48* $94.99 26056 Chrome hand lever assembly. Fits brake side on FL, FX and XL models 41-71 and clutch side on FL models 52-67 (small cable hole) $13.99 130380 Chrome cable tube and fitting.14 long. Fits FL models 49-71. Replaces OEM 45202-50 and 45205-49 $10.99 *Note: Chrome must be removed from inside the drum before installation to prevent damage to linings. w w w.cu sto m c h ro m e.co m TRAN.15
020538 110531 Chrome Brake Line Fittings These brake line fittings are used on handlebar mounted master cylinder and front or rear brake line tees. Fit many models from 72-81. Sold in packs of 5. 020538 Plug 1/8" NPT (repl. OEM 42311-58)....................$3.00 110531 Straight male 1/8" NPT to female 3/8"-24 inverted flare (repl. OEM 63609-72)........................................$1.80 Rear Backing Plate Wheel Cylinder Swivel Fitting Brass fitting replaces the stock piece perfectly. For the rear brake on models from 63-72. Sold each. 19996 Replaces OEM 41750-63...............................$24.99 Master Cylinder and Tee Fitting This 90 right-angle fitting connects the front brake line to the handlebar master cylinder and brake tee. Fits many models from 72-81. 28190 Replaces OEM 43307-78 (pack of 5)......................$4.00 Crush Washers Top-quality washers are made in the USA for the following applications. Sold in packs of 10. 56236 10 mm 82-E89 (repl. OEM 41731-82)......................$0.70 56237 12 mm 84-E91 (repl. OEM 45583-83)......................$0.70 56242 Crush washers, 10 mm, Brake line for Big Twins from 58-72 (repl. OEM 41744-58) Pack of 10...............................$1.00 26447 26448 Universal Stop Light Switch Sold on a display card of 10, or individually. 12287 Sold each.............................................$6.49 12288 Card of 10.............................................$5.60 26440 26435 26429 Chrome Replacement Stop Light Switches Stamped steel construction and heavy-gauge support plates. Ideal for replacing worn stock parts during a restoration project or when building a ground-up full custom. 26447 Fits FX, FXE and FXS models 73-77 (repl. OEM 72005-73A) pushoff style..............................................$15.49 26448 Fits Sportster models 75-76 (repl. OEM 72004-75) pull-on style.....................................................$15.99 26435 Fits Big Twin models 37-57, 45" WL models 37-57 and Servicars 37-50 (repl. OEM 72003-34T) pull-on style...............$22.99 26440 Fits Sportster models 67-74 (repl. OEM 72004-70T) push-off style............................................... $10.99 26429 Fits Sportster and K models 52-66 (repl. OEM 72004-52) pushoff style..............................................$10.99 TRAN.16 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
Front for 5-Speed Touring Models 80-83 and Rear for Sportster Models 77-81 Replaces OEM 44099-77. Brake pad kits for the rear of all Sportster models from 79-81 and XLCR s from 77-78. Also fits the front of all FLT and FLHT models from 80-83 (repl. OEM 43395-80), but you must order two of each part number for a complete brake service on these dual disc models. 8009020 Motor Factory Organic.......$28.99 Rear 82-E87 Replaces OEM 44209-82. Brake pad kits for the rear Girling caliper on all models (except FLT and FLHT models) from 82-E87. 8009021 Motor Factory Organic.......$23.49 Dual Disc Front 77-83 Replaces OEM 44098-77. For all dual disc Sportster, FX and FXR models from 77-83. Packaged 2 pads to a kit (2 sets required for a complete brake service). 8009019 Motor Factory Organic pad set (2 required)................. $24.99 Front and Rear 72-84 Replaces OEMs 44005-78, 44135-74. Brake pad kits for 72-84 front and rear disc brake banana caliper applications. Each kit contains two pads. Fits 73 FX and XL models single disc front brake; FL models single disc front brake 73-84; FL models rear disc brake 73-80; FX models 73-83 rear disc brake.) 8009003 Motor Factory Organic pad set.......................... $22.99 Note: We recommend the replacement of the caliper O-rings and seals whenever replacing brake pads in these calipers. Single Disc Front 74-77 (Kayaba Forks ONLY) Replaces OEM 44281-74. Brake pad kit for all Sportster and FX models with single disc pie-shaped front brake calipers. Each kit contains two pads and four rivets. 12438 Motor Factory Organic........$9.99 Rear for Touring Models from 80-85 Replaces OEM 43957-80. Fit the large dual piston rear caliper on 4-and 5-speed Touring models from 80-85. 18504 Motor Factory Organic.... $19.99 www.customchrome.com TRAN.17
These fine Jammer products are found in the 2014 Custom Chrome Catalog Use the Dealer Locator at customchrome.com to find your local Custom Chrome Dealer TRAN.18 *Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary. Please see Cautionary Information in back of catalog.
General Warnings. Motorcycle riding is a dangerous activity. The only way to be sure to avoid injury is not to ride! Even if you use the finest and best-maintained equipment, wear a helmet and protective clothing, and take all possible precautions, it is not possible to avoid every risk. Motorcycle accidents frequently result in serious injury, including death. Please do not operate a motorcycle or other motor vehicle when you are tired or under the influence of alcohol or drugs, or when your perception is impaired for any other reason. At all times, please wear a helmet, ride carefully and within posted speed limits, and obey all other traffic regulations and instructions from law enforcement personnel. Custom Chrome, sells aftermarket motorcycle parts for Harley-Davidson and other brands. If you do not have the necessary experience and skill, please have a qualified mechanic install any new or replacement part on your motorcycle. The failure to install properly and test any new or replacement component could adversely affect your motorcycle s operation and result in an accident, including a fatal accident. Federal and state laws and regulations impose restrictions on modifying the engine, ignition, exhaust and other components of a motorcycle intended for on-road use. In addition, these laws and regulations impose requirements on windshields, brake components, lighting, and other equipment on your motorcycle. Accordingly, certain parts in this catalog are for competition or display purposes only. In general, those parts are indicated by a Competition mark: a checkered flag in a yellow oval. If you are a retail customer, you are responsible to know the laws and regulations that govern the modification of your motorcycle. Custom Chrome is not responsible if you modify your motorcycle or any component in violation of law. If you have any questions regarding a particular component, please consult your dealer or a qualified motorcycle mechanic. The following is additional information relating to components for sale in various sections of this catalog. This information is not exclusive if you have any questions regarding the installation or use of any component, please contact your dealer, a qualified mechanic, or Custom Chrome s customer service department. This symbol appearing throughout our catalog means that the specified items are high-performance exhaust, carburetor, ignition, or engine components and are not legal for use on pollution or noise-controlled vehicles (except in organized and sanctioned racing or competition events). It is a violation of federal law and the law in every state to install or use any of these components on motorcycles that are licensed for street use or used on public roads. Penalties are substantial. CCI offers these components solely for competition, display, or other off-road use, and is not responsible for any illegal application or use thereof. COPYRIGHT 1982-2014 BY CUSTOM CHROME - A DIVISION OF DAE-IL USA, INC. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED, STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS; ELECTRONIC, MECHANICAL, PHOTOCOPYING, RECORDING, OR OTHERWISE WITHOUT PRIOR WRITTEN PERMISSION OF THE PUBLISHER. www.customchrome.com TRAN.19
155 East Main Ave. Suite 150 Morgan Hill, CA 95037