Product Information MSS Sensor with Quickon Connector 171V62AQ Contents: 1. Specification... 2 2. Product description... 3 3. General Information... 4 4. Application... 4 5. Product Advantage of the MSS- Sensors with Quickon 171V62AQ... 4 6. Availability... 4 7. Connection example... 5 Produktinformation MSS-Sensor mit Quickon Anschluss_e.doc - 1 -
1. Specification Protection class : IP67 (IEC529) Temerature range : -25...+75 C Current limiting resistor: 22 Ohm Material housing: PBT black Operating magnet: 30420000 Air gaps for reliable switching function at 20 C: switch on: max. 4 mm switch off: min. 16 mm minimum air gap: 0,5 mm For other suitable magnets, please consult the factory We reserve the right to change the specification. Circuit shown without power applied. Sensor shown not operated. Produktinformation MSS-Sensor mit Quickon Anschluss_e.doc - 2 -
2. Product description Principle function of the MSS- Sensors 171V62AQ New in the elobau machine safety product group is the sensor 171V62AQ. This is an M30 sensor in PBT material with a 2 normally open contact system and a Quickon connector. The seal on this Quickon connector plug is modified by elobau so that 2 cables can be inserted, enabling these sensors to be daisy- chained (similar to a bus- system). Several sensors can be interconnected (see connection example in section 7). The Quickon plug has the big advantage that you no longer need a defined cable length or a mating connector. On these Quickon connectors the individual wires are inserted directly into the clamp contacts (direct at the sensor) without the need to strip the insulation. By closing the connector cover the wires are fixed into the clamp contacts. Only the cable needs cutting to the prescribed length. This sensor you can operate with all elobau MSS central control units which have a 2 normally open contact system. You can reach up to category 4 according to the machine safety standard EN 954-1depending on the central control unit specified. This new sensor can be operated with the following elobau MSS central control units. The numbers of sensors per sensor input is dependent of the cable length and the cross section of the wire. The lower numbers refer to a maximum- cable length of approx. 500m with a cross section of 0,4mm² per wire: 471M41H31 CAT. 4 max. 25 sensors connected per sensor input 462M51H11 CAT. 4 max. 25 sensors connected per sensor input 462M41H31 CAT. 4 max. 25 sensors connected per sensor input 462M51H21 CAT. 4 max. 25 sensors connected per sensor input 462M41H34 CAT. 4 max. 25 sensors connected per sensor input 462151H1 CAT. 4 max. 3 sensors connected per sensor input 462141H1 CAT. 4 max. 3 sensors connected per sensor input 462151E1 CAT. 3 max. 3 sensors connected per sensor input 462141E1 CAT. 3 max. 3 sensors connected per sensor input Produktinformation MSS-Sensor mit Quickon Anschluss_e.doc - 3 -
3. General Information The MSS- sensor 171V62AQ and a 2 normally open contact system central control unit can reach up to category 4 according to the machine safety standard EN 954-11 (in depending on the central control- unit specified). Ensure that all applicable European directives and national statutory requirements/directives are followed. The product must be used in the original state without any unauthorised changes or modifications. 4. Application The equipment is only to be used for the protection against safety hazards depending upon the safety assessment of individual machines. Potential customers include all general mechanical and electrical engineering industries. 5. Product Advantage of the MSS- Sensors with Quickon 171V62AQ Fulfils the requirements of EN 954-1 / Category 4 (depending on the central control- unit specified) High protection class (IP67) Simplified wiring Installation only requires a non shielded 2-wire cable between the sensors. Economical solution 6. Availability Q I / 2005 (provisional) Produktinformation MSS-Sensor mit Quickon Anschluss_e.doc - 4 -
7. Connection example Produktinformation MSS-Sensor mit Quickon Anschluss_e.doc - 5 -