BARN & FENCE PAINT NO. 25 BARN RED Smooth or rough sawn exterior vertical wood surfaces such as plywood, fences, shingles, shakes, siding. laminates, masonry and stucco surfaces. AVAILABLE IN: Gallon Only No. 25 Barn Red* *Stock Color TINT BASE / MAX TINT* No. 25 128 oz. *NOT TINTABLE Flat. Sheen Level 10.0 20.0 @ 85º Smooth Surfaces First Coat - 400 sq. ft. per gallon Second Coat 500 sq. ft. per gallon Rough Surfaces First Coat 200 sq. ft. per gallon Second Coat 250 sq. ft. per gallon 4 mils wet, 1.40 mil dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 6-8 Hours No. 434 Int./Ext. Oil-Based Primer No. 436 Exterior Water Based Primer Alkyd / Acrylic 37% 47.5% 10.0 1bs. <98 g/l Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: 3/8-3/4 Nap. Depending on New or Weathered Surfaces: Remove mill glaze, loose wood fibers and deteriorated latex or oil-based finishes with BEHR No 64 15 Minute Quik-Fix Deck Finish Remover & Wood Resurfacer. Rinse. Remove mildew with BEHR No. 62 Multi-Surface Deck-Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse Follow the steps above with BEHR No. 63 Cleaner, Brightener Conditioner to open wood grain, neutralize and rejuvenate the natural color of the wood. Rinse thoroughly Previously Coated: - Previously coated surfaces in good condition should be thoroughly cleaned before recoating. Use No. 62 & No 63 as listed above. Do not use if temperature is below 50ºF or if rain is expected within 24 hours. Intermix multiple containers to ensure color and sheen uniformity. Applying 2 coats will provide maximum performance and added protection. Airless spray is recommended for experienced applicators only. Copyright 1999-2006 Behr Process Corporation Revised 9/06
BARN & FENCE PAINT NO. 35 HIGH HIDE WHITE Smooth or rough sawn exterior vertical wood surfaces such as plywood, fences, shingles, shakes, siding. laminates, masonry and stucco surfaces. AVAILABLE IN: Gallon Only No. 35 High Hide White* *Stock Color TINT BASE / MAX TINT* No. 35 128 oz. *NOT TINTABLE Flat Sheen Level 10.0-20.0 @ 85º* Smooth Surfaces First Coat - 400 sq. ft. per gallon Second Coat 500 sq. ft. per gallon Rough Surfaces First Coat 200 sq. ft. per gallon Second Coat 250 sq. ft. per gallon 4 mils wet, 1.40 mil dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 6-8 Hours No. 434 Int./Ext. Oil-Based Primer No. 436 Exterior Water Based Primer Alkyd / Acrylic 35% 51% 11.2 1bs. <96 g/l Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: 3/8-3/4 Nap. Depending on New or Weathered Surfaces: Remove mill glaze, loose wood fibers and deteriorated latex or oil-based finishes with BEHR No 64 15 Minute Quik-Fix Deck Finish Remover & Wood Resurfacer. Rinse. Remove mildew with BEHR No. 62 Multi-Surface Deck-Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse Follow the steps above with BEHR No. 63 Cleaner, Brightener Conditioner to open wood grain, neutralize and rejuvenate the natural color of the wood. Rinse thoroughly Previously Coated: - Previously coated surfaces in good condition should be thoroughly cleaned before recoating. Use No. 62 & No 63 as listed above.. Do not use if temperature is below 50ºF or if rain is expected within 24 hours. Intermix multiple containers to ensure color and sheen uniformity. Applying 2 coats will provide maximum performance and added protection. Airless spray is recommended for experienced applicators only. Copyright 1999-2006 Behr Process Corporation Revised 9/06
FLAT ROOF PAINT No. 65 WHITE REFLECTIVE New or old Unglazed Tile, Masonry Shingle, Anchored Gravel, Aluminum/Metal Materials, Composition Sheets, Asphalt Shingle, Concrete or Cement Block, Urethane Foam, Slate or Wood shaken Wood shake Roofs. It is not intended to waterproof or repair roof leak. This product is intended to brighten roofs and reflect heat. No. 65 White No. 65 126 oz. White 4 oz Custom colors plus computer color matching Flat. *Sheen Level 0-4.0 @ 85º 250 (23m 2 ) sq. ft. per gallon on rough surfaces. 350 (32m 2 )sq. ft. per gallon for second coat. 350 (32m 2 ) sq. ft. per gallons on smooth surfaces. 450 (42m 2 ) sq. ft. for second coat. 4 mils wet, 1.3 mils dry @77 F & 50% humidity* *Longer dry time may be needed in cooler temperatures or higher humidity. To Touch: 2 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water-Based Primer No. 434 Oil-Based Primer 100% Acrylic 35% 53% 11.8 1bs. <250 g/l Or of unused product call 1-800- CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: 1 Nap roller. Depending on the surface If spraying only, thin no more ½ pint of water per gallon Replace brittle or cracked shingles. Clean all roof surfaces. Previously coated surface should be wire brushed or scraped to remove all loose coating. Remove mildew with No. 62 Multi-Surface Deck-Prep Cleaner and Mildew Stain Remover or bleach and water. On galvanized metal, use a diluted solution of No. 991 Concrete Etcher & Rust Remover to prepare surface. If applying on wood shake, clean with No. 63 Wood Cleaner Brightener Conditioner. Follow directions on products labels. Rinse. Allow to dry for 24 hours. Prime all metal, asphalt and wood surfaces. Use product when surface and air temperature are between 50-90 F. Intermix multiple containers, to ensure color and sheen uniformity. Apply starting at the top of the roof working down. Always maintain a wet edge. Copyright 1999-2006 Behr Process Corporation Revised 9/06
FLAT ROOF PAINT No. 66 DEEP BASE New or old Unglazed Tile, Masonry Shingle, Anchored Gravel, Aluminum/Metal Materials, Composition Sheets, Asphalt Shingle, Concrete or Cement Block, Urethane Foam, Slate or Wood shaken Wood shake Roofs. It is not intended to waterproof or repair roof leak. This product is intended to brighten roofs and reflect heat. No. 66 Deep Base No. 66 116 oz. Deep Base 14 oz Custom colors plus computer color matching Flat. *Sheen Level 0-4.0 @ 85º 250 (23m 2 ) sq. ft. per gallon on rough surfaces. 350 (32m 2 )sq. ft. per gallon for second coat. 350 (32m 2 ) sq. ft. per gallons on smooth surfaces. 450 (42m 2 ) sq. ft. for second coat. 4 mils wet, 1.3 mils dry @77 F & 50% humidity* *Longer dry time may be needed in cooler temperatures or higher humidity. To Touch: 2 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water-Based Primer No. 434 Oil-Based Primer 100% Acrylic 31% 44% 11.8 1bs. 17gm/l Material (Includes Water) 50 gm/l Coating (Excludes Water) Or of unused product call 1-800- CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: 1 Nap roller. Depending on the surface If spraying only, thin no more ½ pint of water per gallon Replace brittle or cracked shingles. Clean all roof surfaces. Previously coated surface should be wire brushed or scraped to remove all loose coating. Remove mildew with No. 62 Multi-Surface Deck-Prep Cleaner and Mildew Stain Remover or bleach and water. On galvanized metal, use a diluted solution of No. 991 Concrete Etcher & Rust Remover to prepare surface. If applying on wood shake, clean with No. 63 Wood Cleaner Brightener Conditioner. Follow directions on products labels. Rinse. Allow to dry for 24 hours. Prime all metal, asphalt and wood surfaces. Use product when surface and air temperature are between 50-90 F. Intermix multiple containers, to ensure color and sheen uniformity. Apply starting at the top of the roof working down. Always maintain a wet edge. Copyright 1999-2006 Behr Process Corporation Revised 9/06
ELASTOMERIC MASONRY, STUCCO &BRICK PAINT NO. 68 WHITE Excellent adhesion on new or previously painted exterior vertical surfaces made of stucco, masonry, concrete, concrete block, cement, adjacent or metal trims. No. 68 White Custom colors plus computer color matching available. TINT BASE / MAX TINT* No. 68 120 oz. White 8 oz. Flat *Sheen Level 3.5-5.5 @85º 75-125 sq. ft. per gallon 10 mils wet, 5 mils dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 4-6 Hours Recoat: 24 Hours Cured: 30 Days No. 436 Exterior Water Based Primer 100% Acrylic 48% 60% 10.8 1bs. 44gm/l Material (Includes Water) 84 gm/l Coating (Excludes Water) Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.025-.029 Conventional Spray: Brush: Nylon/Polyester blend Roller: 1 1/4 Nap. Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck- Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Cracks and gaps wider than 1/16 should be routed open, dusted, primed and packed with an elastomeric patching compound prior to product application. Scuff sand glossy surfaces before priming. Prime all chalky, glossy or bare surfaces with BEHR Exterior 100% Acrylic Latex Primer & Sealer. Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Apply one coat of about 10 mils wet film thickness. After 24 hours, a second coat of 10 mils wet film thickness must be applied. A third coat may be required to achieve a final dry mil thickness of about 10-15 mils. Airless Spray: Tip size and atomization pressure will vary depending upon specific equipment used, the viscosity of the coating and temperatures at the time of application.. Copyright 1999-2006 Behr Process Corporation Revised 9/06
INT/EXT MASONRY, STUCCO & BRICK FLAT PAINT NO. 270 WHITE Great for new or old, previously coated interior or exterior vertical surfaces such as brick, masonry, stucco, concrete, cement, slate, stone, cinder block, adobe and clay. No. 270 White Custom colors plus computer color matching available. TINT BASE / MAX TINT* No. 270 126 oz. White 4 oz. Flat *Sheen Level 0-3.5 @85º Rough: 250-300 sq. ft. per gallon Smooth: up to 400 sq. ft. per gallon 4 mils wet, 1.20 mils dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water Based Primer Acrylic Latex 31% 46% 10.8 1bs. 36gm/l Material (Includes Water) 100 gm/l Coating (Excludes Water) Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: ¾ - 1 Nap. Depending on the surface If spraying only, thin no more than ½ pint of water per gallon. Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck- Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Scuff sand glossy surfaces. Patch holes and cracks. Caulk joints and seams. Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Certain colors may require multiple coats. Apply using a high quality roller cover, nylon/polyester brush or airless sprayer. Copyright 1999-2007 Behr Process Corporation Revised 9/07
INT/EXT MASONRY, STUCCO & BRICK FLAT PAINT NO. 271 PASTEL BASE Great for new or old, previously coated interior or exterior vertical surfaces such as brick, masonry, stucco, concrete, cement, slate, stone, cinder block, adobe and clay. No. 271 Pastel Base Custom colors plus computer color matching available. TINT BASE / MAX TINT* No. 271 120 oz. Pastel Base 8 oz. Flat *Sheen Level 0-3.5 @85º Rough: 250-300 sq. ft. per gallon Smooth: up to 400 sq. ft. per gallon 4 mils wet, 1.30 mils dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water Based Primer Acrylic Latex 33% 47% 10.6 1bs. 36gm/l Material (Includes Water) 100 gm/l Coating (Excludes Water) Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: ¾ - 1 Nap. Depending on the surface If spraying only, thin no more than ½ pint of water per gallon. Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck- Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Scuff sand glossy surfaces. Patch holes and cracks. Caulk joints and seams. Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Certain colors may require multiple coats. Apply using a high quality roller cover, nylon/polyester brush or airless sprayer. Copyright 1999-2007 Behr Process Corporation Revised 9/07
INT/EXT MASONRY, STUCCO & BRICK SATIN PAINT NO. 280 WHITE Great for new or old, previously coated interior or exterior vertical surfaces such as brick, masonry, stucco, concrete, cement, slate, stone, cinder block, adobe and clay. No. 280 White Custom colors plus computer color matching available. TINT BASE / MAX TINT* No. 280 126 oz. White 4 oz. Satin *Gloss Level 15.0-25.0 @ 60º Sheen Level 35.0-45.0 @85º Rough: 250-300 sq. ft. per gallon Smooth: up to 400 sq. ft. per gallon 4 mils wet, 1.30 mils dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water Based Primer Acrylic Latex 32.5% 43.5% 10.1 1bs. 56gm/l Material (Includes Water) 150 gm/l Coating (Excludes Water) Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: ¾ - 1 Nap. Depending on the surface If spraying only, thin no more than ½ pint of water per gallon. Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck- Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Scuff sand glossy surfaces. Patch holes and cracks. Caulk joints and seams. Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Certain colors may require multiple coats. Apply using a high quality roller cover, nylon/polyester brush or airless sprayer. Copyright 1999-2007 Behr Process Corporation Revised 9/07
INT/EXT MASONRY, STUCCO & BRICK SATIN PAINT NO. 2-280 WHITE Great for new or old, previously coated interior or exterior vertical surfaces such as brick, masonry, stucco, concrete, cement, slate, stone, cinder block, adobe and clay. No. 2-280 White Custom colors plus computer color matching available. TINT BASE / MAX TINT* No. 2-280 126 oz. White 4 oz. Satin *Gloss Level 15.0-25.0 @ 60º Sheen Level 30.0-45.0 @85º Rough: 250-300 sq. ft. per gallon Smooth: up to 400 sq. ft. per gallon 4 mils wet, 1.30 mils dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water Based Primer Acrylic Latex 33% 44% 10.03 1bs. <50 gm/l Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: ¾ - 1 Nap. Depending on the surface If spraying only, thin no more than ½ pint of water per gallon. Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck- Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Scuff sand glossy surfaces. Patch holes and cracks. Caulk joints and seams. Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Certain colors may require multiple coats. Apply using a high quality roller cover, nylon/polyester brush or airless sprayer. Copyright 1999-2007 Behr Process Corporation Revised 9/07
INT/EXT MASONRY, STUCCO & BRICK SATIN PAINT NO. 281 PASTEL BASE Great for new or old, previously coated interior or exterior vertical surfaces such as brick, masonry, stucco, concrete, cement, slate, stone, cinder block, adobe and clay. No. 281 Pastel Base Custom colors plus computer color matching available. TINT BASE / MAX TINT* No. 281 118 oz. Pastel Base 12 oz. Satin *Gloss Level 15.0-25.0 @ 60º Sheen Level 30.0-45.0 @85º Rough: 250-300 sq. ft. per gallon Smooth: up to 400 sq. ft. per gallon 4 mils wet, 1.30 mils dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water Based Primer Acrylic Latex 32% 41% 9.6 1bs. 56gm/l Material (Includes Water) 149 gm/l Coating (Excludes Water) Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: ¾ - 1 Nap. Depending on the surface If spraying only, thin no more than ½ pint of water per gallon. Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck- Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Scuff sand glossy surfaces. Patch holes and cracks. Caulk joints and seams. Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Certain colors may require multiple coats. Apply using a high quality roller cover, nylon/polyester brush or airless sprayer. Copyright 1999-2007 Behr Process Corporation Revised 9/07
INT/EXT MASONRY, STUCCO & BRICK SATIN PAINT NO. 2-281 PASTEL BASE Great for new or old, previously coated interior or exterior vertical surfaces such as brick, masonry, stucco, concrete, cement, slate, stone, cinder block, adobe and clay. No. 2-281 Pastel Base Custom colors plus computer color matching available. TINT BASE / MAX TINT* No. 2-281 118 oz. Pastel Base 12 oz. Satin *Gloss Level 10.0-20.0 @ 60º Sheen Level 25.0-40.0 @85º Rough: 250-300 sq. ft. per gallon Smooth: up to 400 sq. ft. per gallon 4 mils wet, 1.30 mils dry @77 F & 50% humidity* temperatures or in higher humidity. To Touch: 2-3 Hours Recoat: 4 Hours Cured: Two Weeks No. 436 Exterior Water Based Primer Acrylic Latex 32% 41% 9.6 1bs. <50 gm/l Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip:.015-.017 Brush: Nylon/Polyester blend Roller: ¾ - 1 Nap. Depending on the surface If spraying only, thin no more than ½ pint of water per gallon. Remove all loose, peeling paint using a scraper or sandpaper. Wash off all chalk, dirt, grease, soap and oil-build-up with mild detergent; remove mildew with BEHR No. 62 Multi-Surface Deck- Prep Cleaner & Mildew Stain Remover or bleach and water. Rinse and allow to dry. Scuff sand glossy surfaces. Patch holes and cracks. Caulk joints and seams. Use product when surface and air temperature are between 50º- 90ºF. Intermix multiple containers to ensure color and sheen uniformity. Certain colors may require multiple coats. Apply using a high quality roller cover, nylon/polyester brush or airless sprayer. Copyright 1999-2007 Behr Process Corporation Revised 9/07
Walls subject to hydrostatic pressure. Ideal for above or below grade Walls, Retaining Walls, Garage Walls, Masonry INTERIOR/EXTERIOR Walls, Cinder Blocks, Stucco, Brick, Foundations CONCRETE & MASONRY and Landscape Walls. Apply to dry or slightly damp WATERPROOFING PAINT surfaces. Not for use on floors or walls with active No. 870 WHITE water leaks. No. 870 White No. 870 White 126 oz White - 4oz Flat. *Gloss Level <5% @ 60º On rough porous masonry, 75 100 sq. ft. (7-9m2) per gallon. On smoother surfaces, 100 125 sq. ft. (9-12m2) per gallon. 13 mils wet, 6 mils dry @77 F(25 C) and 50% humidity* temperatures and in higher humidity. To Touch: 1 Hour Recoat: 4 Hours Full Cure: 7-14 Days Acrylic 44% 60% 11.7 1bs. 123 g/l Material (includes water) 219 g/l Coatings (includes water) Or Use soap and water. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP or visit www.earth911.org. SURFACE PREPARATION New or Unpainted Surfaces: New concrete must cure for a minimum of 30 days. Test for loose, flaking concrete by pressing a piece of masking or cellophane tape at various places, then pull it off with an abrupt action. If the tape does not pull the concrete from the surface, it can be painted. If the existing concrete is removed, the loose concrete should be removed down to a sound substrate. All holes or cracks must be properly patched with fast setting hydraulic cement. Remove mildew stains with No. 62 Premium Mildew Stain Remover. Follow all label instructions. All surfaces must be clean and free of dirt, dust, efflorescence and oil. Clean surface with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. TOOLS Airless Spray: Filter: Remove Tip:.023-.025 Fluid pressure: 2,200-3,200 psi Conventional Spray: Brush: Nylon/Polyester Blend Roller: 3/8" to 3/4" Nap. Depending on the surface Con d Previously Painted Surfaces: BEHR No. 870 Concrete & Masonry Waterproofing Paint provides best results when applied to bare or untreated surfaces. Previously Painted Surfaces In Good, Repaintable Condition May Be Painted With Behr No. 870, However, Behr Will Not Guarantee The Results. Test for loose, flaking paint by pressing a piece of masking or cellophane tape at various places, then pull it off with an abrupt action. If the tape does not pull the paint from the surface, it can be painted. If the existing paint is removed, the loose paint should be removed down to a sound substrate by wire brushing or sanding. For Interior or Exterior application; remove deteriorated coating prior to application. Follow all label instructions. Follow all preparation instructions under New or Unpainted Surfaces above. Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air temperature are between 50-90ºF (10-32ºC). Apply to dry or slightly damp masonry walls. Wipe off any visible moisture with a dry cloth before painting. Two coats minimum are required: First Coat: Using a brush or roller, work the waterproofer onto the masonry wall surface making certain to cover any pores or voids. Second Coat: Using a brush or roller, cover the entire surface. Properly fill any voids left after the first coat. Additional spot application may be needed depending on the porosity of the surface. Important: If leaking is still present after two coats, it indicates that voids or pinholes are still open. Re-apply product to these areas. Do Not Thin product or apply at a greater spread rate. Copyright 1999-2008 Behr Process Corporation Revised 2/08
INT/EXT CONCRETE BONDING PRIMER No. 880 Use on Interior or Exterior surfaces such as: Concrete, Masonry, Stucco, Cinder Block and any Porous Stone or Brick. Not designed for use on wood, metal or silicone treated surfaces. Do not use on coated surfaces. Use only on porous surfaces. Note: Some Surfaces May Appear Slightly Darker After Product Dries. AVAILABLE IN: Gallon Only No. 880 Milky and dries clear No. 880 128 oz. Not Tintable Gloss Sheen Level 15-20 @ 60º 350-400 sq. ft. (33-37 m2) per gallon depending on texture and porosity. @77 F & 50% humidity. Must apply a topcoat after at least 8 hours, but before 30 days. To Touch: 2-4 Hours Recoat: 8 Hours Epoxy 16% 15% 8.6 1bs. 37 gm/l Material (Includes Water) 187 gm/l Coating (Excludes Water) Or Commercial Brush Cleaner. Recycle or dispose of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: 60 mesh Tip: 015-.017 Conventional Spray: Not Recommended Brush: Nylon/Polyester blend or Pad Applicator Roller: 3/8-1/2 Nap. Depending on the surface New concrete must cure for a minimum of 30 days prior to priming. Patch all holes and cracks and allow to dry. For touch-ups where surface coatings have failed, completely remove any loose or peeling paint. Do not apply over previously coated surfaces. Remove all dirt, grease and oil with No. 990 Concrete Cleaner & Degreaser. Refer to product label for specific instructions. Etch dense, smooth concrete using BEHR No. 991 Concrete Etcher & Rust Remover. Refer to product label for specific instructions. DO NOT THIN. Stir paint before and occasionally during application. Use product when air and surface temperatures are between 50-90 F (10-32 C). Initial foaming will disappear upon drying. Copyright 1999-2006 Behr Process Corporation Revised 9/06
Basement & Masonry Waterproofing Paint No. 875 Walls subject to hydrostatic pressure. Ideal for above or below grade basement walls, retaining walls, masonry walls, cinder blocks, stucco, brick, foundations and landscape walls. No. 875 White No. 875 White 126 oz White Base - 4oz Flat. *Gloss Level <5% @ 60º On rough porous masonry, 75 100 sq. ft. (7-9m2) per gallon. On smoother surfaces, 100 125 sq. ft. (9-12m2) per gallon. 13 mils wet, 6 mils dry @77 F(25 C) and 50% humidity* temperatures and in higher humidity. To Touch: 1 Hours Recoat: 4 Hours Full Cure: 7-14 Days Acrylic 44% 60% 11.7 1bs. 123 g/l Material (includes water) 219 g/l Coatings (includes water) Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: Remove Tip:.023-.025 Fluid pressure: 2,200-3,200 psi Conventional Spray: Brush: Nylon/Polyester Blend Roller: 3/8" to 3/4" Nap. Depending on the surface All surfaces must be clean and free of dirt, dust, efflorescence, oil and previous coatings. Clean surface with No. 990 Concrete Cleaner & Degreaser. All holes or cracks must be properly patched with a fast setting hydraulic cement. Eliminate mildew stains with BEHR No. 62 Multi-Surface Deck-Prep Cleaner & Mildew Stain Remover or bleach and water. Remove efflorescence with BEHR No. 991 Concrete Etcher & Rust Remover. For Exterior application; use BEHR No. 64 15 Minute Quik-Fix Deck Finish Remover & Wood Resurfacer to remove latex or oilbase finishes. For Interior application; use a chemical stripper designed for interior use. New concrete must be completely cured (minimum 30 days) before application. Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air temperature are between 50º 90ºF (10º-32ºC). Apply to dry or lightly damp masonry walls. Two coats minimum are required: First Coat: Using a brush, work the waterproofer into the pores of the masonry. Second Coat: Using a brush, roller or sprayer, cover the entire surface. Properly fill any voids left after first coat. Additional spot application may be needed depending on the porosity of the surface. Important: If leaking is still present after two coats, it indicates that voids or pinholes are still open. Reapply product to these areas. Do not under apply. Copyright 1999-2007 Behr Process Corporation Revised 2/07
Basement & Masonry Waterproofing Paint No. 2-875 Walls subject to hydrostatic pressure. Ideal for above or below grade basement walls, retaining walls, masonry walls, cinder blocks, stucco, brick, foundations and landscape walls. No. 2-875 White No. 2-875 White 126 oz White Base - 4oz Flat. *Gloss Level <5% @ 60º On rough porous masonry, 75 100 sq. ft. (7-9m2) per gallon. On smoother surfaces, 100 125 sq. ft. (9-12m2) per gallon. 13 mils wet, 6 mils dry @77 F(25 C) and 50% humidity* temperatures and in higher humidity. To Touch: 1 Hours Recoat: 4 Hours Full Cure: 7-14 Days Acrylic 44% 60% 11.7 1bs. 48 g/l Material (includes water) 97 g/l Coating (excludes water) Or of paint call 1-800-CLEANUP (U.S.A. only) www.earth911.org TOOLS Airless Spray: Filter: Remove Tip:.023-.025 Fluid pressure: 2,200-3,200 psi Conventional Spray: Brush: Nylon/Polyester Blend Roller: 1/2" to 3/4" Nap. Depending on the surface All surfaces must be clean and free of dirt, dust, efflorescence, oil and previous coatings. Clean surface with No. 990 Concrete Cleaner & Degreaser. All holes or cracks must be properly patched with a fast setting hydraulic cement. Eliminate mildew stains with BEHR No. 62 Multi-Surface Deck-Prep Cleaner & Mildew Stain Remover or bleach and water. Remove efflorescence with BEHR No. 991 Concrete Etcher & Rust Remover. For Exterior application; use BEHR No. 64 15 Minute Quik-Fix Deck Finish Remover & Wood Resurfacer to remove latex or oilbase finishes. For Interior application; use a chemical stripper designed for interior use. New concrete must be completely cured (minimum 30 days) before application. Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air temperature are between 50º 90ºF (10º-32ºC). Apply to dry or lightly damp masonry walls. Two coats minimum are required: First Coat: Using a brush, work the waterproofer into the pores of the masonry. Second Coat: Using a brush, roller or sprayer, cover the entire surface. Properly fill any voids left after first coat. Additional spot application may be needed depending on the porosity of the surface. Important: If leaking is still present after two coats, it indicates that voids or pinholes are still open. Reapply product to these areas. Do not under apply. Copyright 1999-2007 Behr Process Corporation Revised 2/07
INTERIOR/EXTERIOR OIL-BASED SEMI- GLOSS ENAMEL PAINT NO. 3800 ULTRA PURE WHITE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 3800 - Ultra Pure White No. 3800 - Ultra Pure White Ultra Pure White 2 oz Over 1600 custom colors plus computer color matching Semi-Gloss *Gloss Level 45-55 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.6 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resin 53.4% 72.1% 11.06 1bs. 370 g/l Material (Including Water) 370 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08
INTERIOR/EXTERIOR OIL-BASED SEMI- GLOSS ENAMEL PAINT NO. 3830 DEEP BASE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 3830 Deep Base No. 3830 - Deep Base Deep Base - 14 oz Over 1600 custom colors plus computer color matching Semi-Gloss *Gloss Level 45-55 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.6 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resin 55.0% 69.7% 9.84 1bs. 358 g/l Material (Including Water) 358 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08
INTERIOR/EXTERIOR OIL-BASED SEMI- GLOSS ENAMEL PAINT NO. 3850 PASTEL BASE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 3850 Pastel Base No. 3850 - Pastel Base Pastel Base - 8 oz Over 1600 custom colors plus computer color matching Semi-Gloss *Gloss Level 45-55 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.6 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resin 54.0% 72.0% 10.91 1bs. 365 g/l Material (Including Water) 365 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08
INTERIOR/EXTERIOR OIL-BASED SEMI- GLOSS ENAMEL PAINT NO. 3860 ACCENT BASE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 3860 Accent Base No. 3860 - Accent Base Accent Base 14 oz Over 1600 custom colors plus computer color matching Semi-Gloss *Gloss Level 45-55 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.6 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resin 55.7% 71.9% 10.0-12.0 1bs. 352 g/l Material (Including Water) 352 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08
INTERIOR/EXTERIOR OIL-BASED HIGH- GLOSS ENAMEL PAINT NO. 8800 ULTRA PURE WHITE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 8800 - Ultra Pure White No. 8800 - Ultra Pure White Ultra Pure White 2 oz Over 1600 custom colors plus computer color matching High-Gloss *Gloss Level >88 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.5 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resins 52.0% 68.0% 9.8 1bs. 379 g/l Material (Including Water) 379 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08
INTERIOR/EXTERIOR OIL-BASED HIGH- GLOSS ENAMEL PAINT NO. 8830 DEEP BASE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 8830 Deep Base No. 8830 - Deep Base Deep Base - 14 oz Over 1600 custom colors plus computer color matching High-Gloss *Gloss Level >88 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.5 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resins 52% 61% 8.2 1bs. 379 g/l Material (Including Water) 379 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08
INTERIOR/EXTERIOR OIL-BASED HIGH- GLOSS ENAMEL PAINT NO. 8850 PASTEL BASE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 8850 Pastel Base No. 8850 - Pastel Base Pastel Base 8 oz Over 1600 custom colors plus computer color matching High-Gloss *Gloss Level 45-55 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.5 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resins 52% 67% 9.6 1bs. 379 g/l Material (Including Water) 379 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08
INTERIOR/EXTERIOR OIL-BASED HIGH- GLOSS ENAMEL PAINT NO. 8860 ACCENT BASE AVAILABLE IN: Quart & Gallon Properly prepared Interior or Exterior surfaces such as: Wood, Drywall, Plaster, Masonry, Metal, Well-bonded Wallpaper, Brick, Stucco, Aluminum and Cinder Block. Do not use on horizontal surfaces. No. 8860 Accent Base No. 8860 - Accent Base Accent Base 14 oz Over 1600 custom colors plus computer color matching High-Gloss *Gloss Level >88 @ 60º 500-550 sq. ft. (46-51 m2) per gallon over primed smooth surfaces and 350-400 sq. ft. (33-37 m2) per gallon over primed rough surfaces. 2.9 mils wet, 1.5 mils dry @77 F & 50% humidity Longer dry time required in cooler temperatures and higher humidity. To Touch: 4-5 Hours Recoat: 24 Hours Cured: 7 Days N0. 436 Acrylic Primer & Sealer No. 434 Oil-Based Primer & Sealer Alkyd Resins 52% 63% 8.6 lbs. 379 g/l Material (Including Water) 3790 g/l Coating (Excludes Water) 104 F (40º C) Or Use mineral spirits. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call 1-800- CLEANUP (U.S.A. only) or visit www.earth911.org. TOOLS Airless Spray: Filter: 60 mesh Tip:.013 -.015 Brush: High Quality China Bristle Brush Roller: 1/4-3/8" Nap. Depending on the surface Allow new stucco, plaster and masonry to cure for 30 days. CLEAN: For interior and exterior surfaces, remove dirt, oil and grease stains with No. 990 Concrete & Masonry Cleaner/Degreaser. To remove mildew stains, use BEHR No. 62 Premium Mildew Stain Remover. Remove all loose and peeling paint; scuff sand glossy surfaces; caulk; repair imperfections and sand smooth. For exterior surfaces, powerwash to remove chalk. Etch galvanized metal with BEHR No. 991 Concrete & Masonry Cleaner/Etcher. Follow all label instructions. PRIME: Use BEHR N0. 436 100% Acrylic Primer & Sealer or BEHR N0. 434 Oil-Based Primer & Sealer. Follow all label instructions. DO NOT THIN. Stir before and during application. When working with more than one can of the same product, intermix to ensure color uniformity. Use adequate ventilation during application & drying process. Certain colors may require more than one coat to achieve complete hide and coverage. Use product when air and surface temperatures are between 40 90 F (4-32 C). Copyright 1999-2008 Behr Process Corporation Revised 2/08