PRISM Low VOC Single Stage Color Flat (76), Satin (77), Semi-Gloss (78), & Gloss (79)

Transcription

1 PRISM Low VOC Single Stage Color Flat (76), Satin (77), Semi-Gloss (78), & Gloss (79) Product Data Sheet PRODUCT DESCRIPTION Prism Low VOC Single Stage Color is a two-component urethane coating. This premium single stage system utilizes two mixing clears (6410 & 6411) to reach multiple gloss levels (Flat, Satin, Semi- Gloss, and Gloss). Prism Low VOC Single Stage has high performance qualities that include extreme durability, resistance to stone chipping, and a chemical / solvent resistant finish. Prism Low VOC Single Stage Color can be taped in one hour and is ideal for use when applying multiple colors or striping. Prism Low VOC Single Stage Color was designed for Fleet Refinish, OE, and Sign Manufacturing segments. SUITABLE PRIMERS Tec/BASE Surfacers and, TP530, TP531, TP532 Complete Color Surfacer System, TP520 series & TP527 Series 3.5/2.1 DTM Epoxy Primers, 5220, 5221, 5523, 5225, 5226, 5227, 5273, 5274, TP570, TP DTM Urethane Primers, 5204, 5205, 5206, 5211, 5212 SURFACE PREPARATION Bare Substrates Choose appropriate Martin Senour primer and refer to product recommendations. Wash surfaces with a mild detergent in hot water. Rinse well and wipe dry with clean cloth. Solvent clean with Martin Senour Surface Cleaner V800, 6383, 6384, or 6388, and wipe dry with a clean cloth. Grind repair area to remove paint and all rust as needed. Sand all areas to be refinished and featheredge all broken film areas. Treat bare metal with a Martin Senour conditioner or etching primer. Check local regulations to verify etching primers are VOC exempt. Prepainted Substrates: 1. Complete body work and priming according to product recommendations for appropriate Martin Senour primer. 2. Finish sand repair area with 320 grit treated sandpaper on a random orbital sander. 3. Re-clean thoroughly with V800, 6383, 6384 or For best results on larger repairs, seal the area to be painted with an appropriate Martin Senour primer (for the above products refer to the appropriate product data page for complete information). NOTE: Please check local VOC regulations before selecting any surface cleaners 2015 The Martin Senour Company Page 1 of 6 MA5241 Cleveland, OH /03/2015

2 MIXING RATIO Stir or shake Prism Low VOC Single Stage Color thoroughly before mixing. Flat (76): Utilizing 6410 mixing clear, mix 5 parts color with 1 part 6496 Hardener. Satin / Semi-Gloss (77 / 78): Utilizing 6410 mixing clear, mix 4 parts color with 1 part 6496 Hardener. Gloss (79): Utilizing 6411 mixing clear, mix 3 parts color, with 1 part 6496 Hardener, with up to 10% 6588 Reducer. Add 3 oz 6597 Accelerator per sprayable gallon for accelerated dry times. Flat (76) Flat Mixing Ratio Satin (77) & Semi-Gloss (78) Mixing Ratio Gloss (79) Mixing Ratio 5 Parts Prism 76 intermix + 1 Part 6496 Hardener 4 Parts Prism 77 or Part 6496 Hardener 3 Parts Prism 79 intermix Part 6496 Hardener Up to 10% 6588 Reducer Optional: For 76, 77 & 78 Mixing options, add up to ½ part reducer 6588 or CS5 to lower viscosity. POT LIFE Time: Temperature: Reduced Gloss: F High Gloss: 2 75 F APPLICATION Overall Adjust air pressure at the gun to psi for siphon, gravity or pressure feed (adjust pot pressure to 5-10 psi for 8-14 fluid ounces per minute delivery). For HVLP adjust to 5-10 psi at the cap. For Pressure/Siphon feed, apply 2 medium coats at a gun distance of 8-10 inches. Spray to hiding. For HVLP, apply 1 full wet coat with 70% overlap, applying the second coat in a cross-coat method. Recommended dry film thickness is mils. Clean spray gun immediately after use with Gun and Equipment Cleaner. Repair Repair process must be performed using a two-gun method. Apply Prism Low VOC Single Stage Color over the repaired area carrying out the wet edge just beyond the repair. Allow Prism Low VOC Single Stage Color to dry minutes. Apply a second coat to achieve proper hiding and blending of the color into the repaired area and lightly feather the outer edge. Immediately after feathering the final coat, melt the feathered edge with a wet-on-wet application using Tec/Blend Plus TBS8 of TBS11 1K Urethane Blending Solvent The Martin Senour Company Page 2 of 6 MA5241

3 APPLICATION CONTINUED Buffing Blend Area Allow finish to cure according to recommended drying schedule. If sanding is needed for dirt or smoothing the blend area, use 2000 to 2500 grit wet paper. Buff blend area by machine with a quality micro-finishing compound followed by machine glaze. Hand glaze if needed. EQUIPMENT Gun Type Nozzle Air Pressure Conventional Siphon Feed mm psi Conventional Gravity Feed mm psi Conventional Pressure Feed mm at 8-14 oz/min psi HVLP Gravity Feed mm 5-10 psi at cap HVLP Pressure Feed mm at 8-14 oz/min 5-10 psi at cap Reduced Pressure Gravity Feed mm Follow Recommendations Reduced Pressure Feed mm Follow Recommendations THEORETICAL COVERAGE Square Foot 1 mil Dry (white) 715 FT 2 /gal DRYING SCHEDULE Air Dry Times with 3 oz 6597 Accelerator Dry Film Thickness during testing 3.5 mils Handslick Prism 76 Prism 77 Prism 78 Prism Minutes 12 Minutes 12 Minutes 14 Minutes Tack Free 3 Hours 5 Hours 5.5 Hours 2.5 Hours Dust Free 3 Hours 5.5 Hours 5.5 Hours 2.5 Hours Nib Sandable 3.5 Hours 5.5 Hours 5.5 Hours 3 Hours Tape Free 5 Hours 5.5 Hours 5.5 Hours 3.5 Hours 2015 The Martin Senour Company Page 3 of 6 MA5241

4 DRYING SCHEDULE - CONTINUED NOTES: Prism Low VOC Single Stage Color can be recoated with itself up to 72 hrs without scuff sanding. After 72 hrs scuff sanding is required. TECHNICAL DATA Prism 76 Force Dry Times with 3 oz 6597 Accelerator Dry Film Thickness during testing 3.5 mils Prism 76 Prism 77 Prism 78 Prism 79 Handslick 10 Minutes 12 Minutes 12 Minutes 14 Minutes Tack Free 5 Minutes 5 Minutes 5 Minutes 5 Minutes Dust Free 5 Minutes 5 Minutes 5 Minutes 5 Minutes Nib Sandable 5 Minutes 15 Minutes 15 Minutes 5 Minutes Tape Free 15 Minutes 75 Minutes 60 Minutes 5 Minutes Mixing Ratio by Volume 5:1 Pot Life 1-2 hours Max VOC(with 5:2: Ready to Spray Volume Solids 49.5% Recommended Dry Film Thickness sq ft/gal Gloss 60 Gloss will vary Prism 77 Mixing Ratio by Volume 4:1 Pot Life 1-2 hours Max VOC(with 5:2: Ready to Spray Volume Solids 44.6% Recommended Dry Film Thickness sq ft/gal Gloss Prism 78 Mixing Ratio by Volume 4:1 Pot Life 1-2 hours Max VOC(with 5:2: Ready to Spray Volume Solids 44.6% Recommended Dry Film Thickness sq ft/gal Gloss Prism 79 Mixing Ratio by Volume 3:1 Pot Life 2 hours Max VOC(with 5:2: Ready to Spray Volume Solids 57.8% Recommended Dry Film Thickness sq ft/gal Gloss 20 or Gloss Levels may vary based on color, application and film build The Martin Senour Company Page 4 of 6 MA5241

5 PERSONAL PROTECTION Read label, directions, and MSDS before use. Refer to MSDS for specific information. Wear a NIOSH approved organic vapor respirator when using this product. Wear a NIOSH approved dust particulate mask when sanding, mixing, or applying this product. Keep product, paint, and overspray off of the skin, wear goggles, coveralls, and chemical protective gloves when using this product. REGULATORY DATA Prism 76 As Packaged As Applied Density % by Wt. % by Vol. % by Wt. % by Vol. Volatiles Water Exempt Compounds VOC Total VOC Less Exempt Lb/Gal KG/L Lb/Gal KG/L HAPs Prism 77 & 78 As Packaged As Applied Density % by Wt. % by Vol. % by Wt. % by Vol. Volatiles Water Exempt Compounds VOC Total VOC Less Exempt Lb/Gal KG/L Lb/Gal KG/L HAPs Prism 79 As Packaged As Applied Density % by Wt. % by Vol. % by Wt. % by Vol. Volatiles Water Exempt Compounds VOC Total VOC Less Exempt Lb/Gal KG/L Lb/Gal KG/L HAPs The Martin Senour Company Page 5 of 6 MA5241

6 LABEL CAUTIONS Prism Low VOC Single Stage Color DANGER! FLAMMABLE! VAPOR AND SPRAY MIST HARMFUL, OVEREXPOSURE MAY CAUSE LUNG DAMAGE. MAY CAUSE ALLERGIC RESPIRATORY AND SKIN REACTION, EFFECTS MAY BE PERMANENT. HARMFUL IF INHALED MAY AFFECT THE BRAIN OR NERVOUS SYSTEM, CAUSING DIZZINESS, HEADACHE OR NAUSEA. IRRITATES EYES, SKIN AND RESPIRATORY TRACT. DRIED FILM OF THIS PAINT MAY BE HARMFUL IF EATEN OR CHEWED. Contents are FLAMMABLE. Vapors may cause flash fires. Keep away from heat, sparks, and open flame. During use and until all vapors are gone: Do not smoke-extinguish all flames, pilot lights, and heaters Turn off stoves, electric tools and appliances, and any other sources of ignition. VAPOR AND SPRAY MIST HARMFUL. Gives off harmful vapor of solvents and isocyanates. DO NOT USE IF YOU HAVE CHRONIC (LONG-TERM) LUNG OR BREATHING PROBLEMS, OR IF YOU HAVE EVER HAD A REATINO TO ISOCYANATES. USE ONLY WITH ADEQUATE VENTILATION. WHERE OVERSPRAY IS PRESENT, A POSITIVE PRESSURE AIR SUPPLIED RESPIRATOR (NIOSH approved) SHOULD BE WORN TO PREVENT EXPOSURE. IF UNAVAILABLE, AN APPROPRIATE PROPERLY FITTED APPROVED NIOSH VAPOR/PARTICULATE RESPIRATOR MAY BE EFFECTIVE. Follow respirator manufacturer s directions for respirator use. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage. FIRST AID: IF INHALED: If affected, remove from exposure. Restore breathing, Keep warm and quiet. If on SKIN: Wash affected area thoroughly with soap and water. Remove contaminated clothing. Launder before re-use. If in EYES: Flush eyes with large amounts of water for 15 minutes. Get medical attention. If SWALLOWED: Call Poison Control Center, hospital emergency room, or physician immediately. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. May contain Lean which may cause birth defects, kidney, central and peripheral nervous system damage and blood effects. May contain Lead Chromate which can cause cancer. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN. Do not apply on toys and other children s articles, furniture, or any interior surface of a dwelling or facility which may be occupied or used by children. Do not apply on any exterior surface of dwelling units, such as window sills, porches, stairs, or railings, to which children may be commonly exposed. FOR PROFESSIONAL USE ONLY. SEE MATERIAL SAFETY DATA SHEET Reducer DANGER! HARMFUL OR FATAL IF SWALLOWED. EXTREMELY FLAMMABLE - VAPORS MAY CAUSE FLASH FIRES! HARMFUL IF INHALED - MAY AFFECT THE BRAIN OR NERVOUS SYSTEM, CAUSING DIZZINESS, HEADACHE OR NAUSEA. IRRITATES EYES, SKIN AND RESPIRATORY TRACT. Before using, carefully read CAUTIONS on back panel. Contents are EXTREMELY FLAMMABLE. Keep away from heat, sparks, and open flame. Vapors will accumulate readily and may ignite explosively. During use and until all vapors are gone: Keep area ventilated - Do not smoke - Extinguish all flames, pilot lights and heaters Turn off stoves, electric tools and appliances, and any other sources of ignition. VAPOR HARMFUL. Use only with adequate ventilation. Wear an appropriate properly fitted vapor/particulate respirator (NIOSH approved) during and after application. Follow respirator manufacturer's directions for respirator use. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage Hardener DANGER! HARMFUL OR FATAL IF SWALLOWED. EXTREMELY FLAMMABLE - VAPORS MAY CAUSE FLASH FIRES! HARMFUL IF INHALED - MAY AFFECT THE BRAIN OR NERVOUS SYSTEM, CAUSING DIZZINESS, HEADACHE OR NAUSEA. IRRITATES EYES, SKIN AND RESPIRATORY TRACT. Before using, carefully read CAUTIONS on back panel. Contents are EXTREMELY FLAMMABLE. Keep away from heat, sparks, and open flame. Vapors will accumulate readily and may ignite explosively. During use and until all vapors are gone: Keep area ventilated - Do not smoke - Extinguish all flames, pilot lights and heaters Turn off stoves, electric tools and appliances, and any other sources of ignition. VAPOR HARMFUL. Use only with adequate ventilation. Wear an appropriate properly fitted vapor/particulate respirator (NIOSH approved) during and after application. Follow respirator manufacturer's directions for respirator use. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage The Martin Senour Company Page 6 of 6 MA5241