USB2.0 to Ethernet adapter Quick Installation Guide Version 1.0 July, 2006
Multi-Languages QIG in Driver CD ============================= Český: Anglického průvodce rychlou instalací naleznete na přiloženém CD s ovladači Deutsch: Finden Sie bitte das englische QIG beiliegend in der Treiber CD (German) Español: Incluido en el CD el QIG en Ingles. Français: Veuillez trouver l anglais QIG ci-joint dans le CD driver Italiano: Incluso nel CD il QIG in Inglese. Magyar: Az angol telepítési útmutató megtalálható a mellékelt CD-n Nederlands: De engelstalige QIG treft u aan op de bijgesloten CD Polski: Skrócona instrukcja instalacji w języku angielskim znajduje się na załączonej płycie CD Português: Incluído no CD o QIG em inglês. Русский: Найдите QIG на анлийском языке на приложеном CD Türkçe: Ürün ile beraber gelen CD içinde Türkçe Hızlı Kurulum Kılavuzu'nu bulabilirsiniz
English Introduction Thank you for purchasing the USB2.0 10/100Mbps to Fast Ethernet Adapter. This unique cable adapter allows you to connect your computer into Internet in the fast and easy way. Specifications Standards IEEE 802.3 10Base-T and 802.3u 100Base-TX Compliant USB specification 1.0 /1.1 and 2.0 compliant Connection Mode Full or Half duplex for both 10Mbps and 100Mbps Media Supported Category-3, 4, 5 for 10Base-T and Category 5 for 100Base-TX LEDs Link/Active LED indicator Feature USB specification revision 1.0/1.1 and 2.0 full speed compliant Complies with IEEE 802.3 10Based-T and 802.3u 100Base-TX USB interface to desktop/notebook PC without power adapter RJ-45 connector to 10Mbps or 100Mbps Ethernet networks 10/100Mbps Auto-Sense Full/Half Duplex auto-negotiation for both 10Base-T and 100Base-TX Compatible with Windows 98SE / ME / 2000 / XP Device Installation Guide Follow the steps below on installing the USB2.0 10/100 Fast Ethernet adapter cable: Step1. Please connect the male B-connector of 1.5M USB2.0 cable to the female USB B-connector of USB2.0 Fast Ethernet Adapter and RJ-45 connector of networking cable to another end of USB2.0 Fast Ethernet Adapter. Step2. Connect the male A-connector of 1.5M USB2.0 cable to an available USB2.0 port on the computer or an available USB2.0 port on the USB2.0 HUB plugged into the computer.
Driver installation for Windows 98SE / Me Step1. Power on the computer. New Hard Ware Found window comes up to request you to insert the driver diskette, and click OK. Step2. Select Search the proper files of driver, and click Next. Step3. Insert the driver disc into the computer. Select CD-ROM Devices or specify a Location link D:\Driver\EU-4206, and click Next. Step4. The driver will be found, and click Next to proceed. Step5. The system will ask windows 98SE original disk. Step6. Please insert the disk, and the system will install driver automatically. Step7. Click Finished completing installation. Step8. Windows 98SE / Me will find the driver and automatically configure the USB Fast Ethernet Adapter. Step9. Reboot the computer and remove the driver disc. The driver will take effect. Step10. Check if the device is complete install in your computer My Computer (right key on the mouse) content Hardware Device Manager.
Driver installation for Windows 2000 Step1. Power on the computer. When the New Hardware Found Wizard window comes up, click Next to install the driver. Step2. Select Search the proper files of driver, and click Next. Step3. Insert the driver disc into the computer. Select CD-ROM Devices or specify a Location link D:\Driver/EU-4206, and click Next. Step4. The driver will be found, and click Next to proceed. Step5. Click Finished to complete installation. Step6. Windows 2000 will automatically configure the USB Fast Ethernet Adapter. Step7. Reboot the computer and remove the driver disc. The driver will take effect. Step8. Check if the device is complete install in your computer My Computer (right key on the mouse) content Hardware Device Manager.
Driver Installation for Windows XP Step1. Power on the computer. When the New Hardware Found Wizard windows comes up, select install from a list or a specific location (Advanced), and click Next. Step2. Insert the driver disc into the computer. Select CD-ROM Devices or specify a Location link D:\Driver/EU-4206, and click Next. Step3. Windows XP will find the driver and request to continue installing and copying needed files. Step4. Click Finished to complete the installation. Step5. A dialogue box will appear above the taskbar showing New network device installed. Step6. Reboot the computer and remove the driver disc. The driver will take effect. Step7. Check if the device is complete install in your computer Star My Computer (right key on the mouse) content Hardware Device Manager