ATX12V / EPS12V Power Supply TG-I460R (460W+460W) TG-I550R (550W+550W) User Manual
Table of Contents 1 Introduction 2 General specification 3 Installation 4 Pin assignment & function of connectors 5 Drawing Warranty 3 (Three) years manufacture s warranty. Date code indicating week and year of manufacture All brand names and trademarks are the property of their respective owners. All above specifications are subject to change without prior notice!
Introduction The TG-I460R & TG-I550R series (Mini Redundant Power Supply) Switching Mode Power Supply is compliant with the latest EPS12V Ver. 2.9 and ATX12V Ver. 2.2. The TG-I460R & TG-I550R, high reliability power supplies are designed for 4U rackmount server and server tower. These high-density units meet the electrical and mechanical requirements and diversified into various applications. Features Universal AC input power With active power factor correction (PFC) Protection circuits designed-in Meet EPS12V Ver. 2.9 and ATX12V Ver. 2.2 specification Backward compatibility, -5V available Industrial DIN-connector for reliability Automatic thermal control (Fan speed control) PS2 size with redundant configuration Standard PC connection / wiring interface Hot-Swap / Hot-Plug application Power failure alarm & signals MTBF (Demonstrated) greater than 100,000 hours 3 years warranty
2. Specification 2.1 The range of AC input voltage 100-240 VAC with active Power Factor Correction (PFC) 2.2 DC output characteristics During operation the maximum load shall not be exceeded 460 / 550 Watts. The total load on +5V and +3.3V shall not be exceeded 180 watts for 550W and 220 watts for 460W. 460W+460 550W+550 Voltage / Function Min Current W Max. W Max. Current Current +5VDC 0A 35A 30A +3.3VDC 0A 22A 24A +12VDC 0A 32A 41A -5VDC 0A 0.5A 0.5A -12VDC 0A 1A 1A 5VSB 0.1A 2A 2A 2.3 Operating Environment Maximum operating temperature is 40 ºC Maximum operating Humidity is 90% RH 2.3 LED Instructions There is a LED indicated power supply s status within Module s front panel. Power Status Stand by Power ON Power Fault Configure 2-1: LED Instructions LED Color Amber Green Red
Description and Illustration for Connectors: a. ATX12V 24Pin Main Power Connector Pin Signal Color Orange +3.3VDC 13 1 +3.3VDC Orange BRN. +3.3VS 13 Blue -12VDC 14 2 +3.3VDC Orange COM 15 3 COM Green PS-ON 16 4 +5VDC Red COM 17 5 COM COM 18 6 +5VDC Red COM 19 7 COM White -5VDC 20 8 PG Gray Red +5VDC/+5VS 21 9 +5VSB Purple Red +5VDC 22 10 +12VDC Yellow Red +5VDC 23 11 +12VDC Yellow 4 12 +3.3VDC Orange b. P4 optional +12V connector (4 Pin) COM 1 Yellow +12VDC 3 Yellow +12VDC 4 c. EPS +12V connector (8Pin) COM 1 COM 3 COM 4 Yellow +12VDC 5 Yellow +12VDC 6 Yellow +12VDC 7 Yellow +12VDC 8 d. (HDD) Drive connector (4 Pin) COM 3 Red +5VDC 4
e. (FDD) Floppy connector (4 Pin) COM 3 Red +5VDC 4 Switching Power Supply User Manual f. SATA connector (5 Pin) Red +5VDC 3 COM 4 Orange +3.3VDC 5 g. PCI-E connector (6 Pin) Yellow +12VDC 2 Yellow +12VDC 3 COM 4 COM 5 COM 6 g. Signal cable connector (2 Pin) Signal Type Color Orange Total PFD Blue PW1 PFD Yellow PW2 PFD Alarm Reset White Description Power Failure Detection for power modules, TTL Signal Power Dailure Detection for Module 1, TTL Signal Power Dailure Detection for Module 2, TTL Signal Short can cancel the buzzer for alarm, sam as Front panel reset SW WARNING: Please turn off the main on/off switch and do not plug the individual power supplies input cables before install the power
Installation Firstly, make sure that your computer is turned off when you are fitting this power supply into an existing system, and then remove the main power cord. Open the case of your PC; remove all connectors from the drive and motherboard. Release the four screws and remove the old power supply. Place the power supply in the case and fix it with four screws. Connect all drives and the motherboard to power supply. (Describing as Descriptions and illustration connectors ) and make sure that the push button in the case is connected to the motherboard.