Introduction Application Modular I/O system with IP20 degree of protection, particularly suitable for user-specific and complex automation tasks Can be expanded with S7-300 automation system signal, communication and function modules Applicable Ex analog input or output modules with HART optimize the for use in process engineering Can be used in redundant systems (S7-400H, S7-400F/FH) Consists of a PROFIBUS DP or PROFINET interface module IM 153, up to 8 or 12 I/O modules of the S7-300 automation system (structure with bus connection or with active bus modules), and a power supply if applicable Modules can be replaced during operation (hot swapping) with the bus modules active Transmission rates up to 12 Mbit/s Ex approval to Cat. 3 for Zone 2 acc. to ATEX100 a Failsafe digital in/outputs as well as analog inputs for safetyoriented signal processing in accordance with PROFIsafe Support of modules with expanded user data, e.g. HART modules with HART minor variables Technical specifications General technical data Cables and connections Degree of protection Screw and spring-loaded connections in permanent wiring IP20 Ambient temperature on vertical wall (preferred mounting position) with horizontal assembly 0 to +60 C with other assembly 0 to +40 C Relative humidity 5 to 5% (RH stress level 2 according to IEC 1131-2) Atmospheric pressure 75 to 1080 hpa Mechanical stress Vibrations IEC 68, parts 2 6: 10-57 Hz (const.amplitude 0.075 mm) 57-150 Hz (constant acceleration 1 g) Shock IEC 68, parts 2 27 half-sine, 15 g, 11 ms /11
Interface modules IM 153-1/153-2 The system with various interface modules is available for the decentralized use of S7-300 I/O modules. Depending on the application purpose, the best suited IM in terms of costs and functions can be selected: IM 153-1 Standard The IM 153-1 is one reasonably priced variant that is best suited for most applications in the manufacturing environment. It permits the use of up to 8 S7-300 I/O modules. IM 153-2 High Feature For higher requirements in manufacturing technology, such as the use of F-technology or the highest performance in conjunction with clock synchronization, the IM 153-2 High Feature is available. This IM is also designed for use with the PCS 7 in the field of manufacturing applications. This IM can be redundantly used and supports typical functions as they are required in the control field. These include, for example, clock synchronization or time stamping with an accuracy of up to 1ms. Technical specifications 6ES7 153-1AA03-0XB0 6ES7 153-2BA02-0XB0 6ES7 153-2BA82-0XB0 General information Vendor identification (VendorID) 801Dh 801Eh 801Eh Supply voltage 24 V DC permissible range, lower limit (DC) 20.4 V 20.4 V 20.4 V permissible range, upper limit (DC) 28.8 V 28.8 V 28.8 V permissible range (ripple included), 20.4 V 20.4 V 20.4 V lower limit (DC) permissible range (ripple included), 28.8 V 28.8 V 28.8 V upper limit (DC) External protection for supply cables not necessary 2.5 A 2.5 A (recommendation) Mains buffering Mains/voltage failure stored energy 5ms 5ms 5ms time Input current Current consumption, max. 350 ma; at 24 V DC 650 ma 650 ma Rated value at 24 V DC 625 ma Inrush current, typ. 2.5 A 3A 3A I²t 0.1 A² s 0.1 A² s 0.1 A² s Output voltage Rated value, 5 V DC Output current for backplane bus (5 V DC), max. 1A 1.5 A 1.5 A Power losses Power loss, typ. 3W 5.5 W 5.5 W Address area Addressing volume Outputs 128 byte 244 byte 244 byte Inputs 128 byte 244 byte 244 byte /12
Interface modules IM 153-1/153-2 Technical specifications (continued) Hardware configuration Number of modules per DP slave interface, max. Time stamping Accuracy 8 12 12 1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules Number of message buffers 15 15 Messages per message buffer 20 20 Number of stampable digital inputs, max. 6ES7 153-1AA03-0XB0 6ES7 153-2BA02-0XB0 6ES7 153-2BA82-0XB0 128; Max. 128 signals/station; max. 32 signals/slot 1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules 128; Max. 128 signals/station; max. 32 signals/slot Time format RFC 111 RFC 111 Time resolution 0.466 ns 0.466 ns Time interval for transmitting the message 1 000 ms 1000ms buffer if a message is present Time stamp on signal change rising / falling edge as signal entering or exiting rising / falling edge as signal entering or exiting Interfaces Interface physics, RS 485 Interface physics, FOC No No No PROFIBUS DP Node addresses 1 to 125 permitted 1 to 125 permitted 1 to 125 permitted Automatic detection of transmission speed PROFIBUS DP, output current, max. 0 ma 70 ma 70 ma Transmission procedure RS 485 RS 485 RS 485 Transmission rate, max. 12 Mbit/s 12 Mbit/s 12 Mbit/s SYNC capability FREECE capability Direct data exchange ; Sender ; Sender ; Sender (slave-to-slave communication) PROFIBUS DP -pin sub D socket -pin sub D -pin sub D 1st interface DP slave GSD file (for DPV1) SIEM801D.GSD; SI04801.GSG SI0480E.GSG SI01801D.GSG Automatic baud rate search Communication functions Bus protocol/transmission protocol PROFIBUS DP to EN 50170 PROFIBUS DP to EN 50170 PROFIBUS DP to EN 50170 Isolation Isolation checked with Isolation voltage 500 V Isolation voltage 500 V Isolation voltage 500 V Degree and class of protection IP20 Ambient conditions Operating temperature Min. 0 C 0 C -25 C max. 60 C 60 C 60 C Air pressure Operating altitude above sea level, 3 000 m 3 000 m 3000m max. Dimensions Width 40 mm 40 mm 40 mm Height 125 mm 125 mm 125 mm Depth 117 mm 117 mm 117 mm Weight Weight, approx. 360 g 360 g 360 g /13
Interface modules IM 153-1/153-2 Technical specifications (continued) belongs to product Dimensions Width Height Depth Weight Weight, approx. 6ES7 15-7HD10-0XA0 7 mm 2 mm 30 mm 133 g 6ES7 15-7HA00-0XA0 6ES7 15-7HB00-0XA0 6ES7 15-7HC00-0XA0 Dimensions Width 7 mm 7 mm 7 mm Height 2 mm 2 mm 2 mm Depth 30 mm 30 mm 30 mm Weight Weight, approx. 111 g 140 g 127 g Ordering data Order No. Order No. IM 153-1 interface module Slave interface for connecting PROFIBUS bus connector an to PROFIBUS DP 0 outgoing cable, terminating Standard temperature range 6ES7 153-1AA03-0XB0 resistor with disconnecting function, IM 153-2 interface module up to 12 Mbit/s, FastConnect Slave interface for connecting an Without PG interface to PROFIBUS DP; 1 unit 6ES7 72-0BA52-0XA0 also for use in redundant systems 100 units 6ES7 72-0BA52-0XB0 High Feature 6ES7 153-2BA02-0XB0 With PG interface High Feature with extended 6ES7 153-2BA82-0XB0 temperature range 1 unit 6ES7 72-0BB52-0XA0 100 units 6ES7 72-0BB52-0XB0 Active IM 153 /IM 153 bus module 6ES7 15-7HD10-0XA0 For two IM 153-2 High Feature modules for designing redundant systems Bus module for To accommodate a power supply and an IM 153 module for the hotswapping function during RUN, incl. bus module cover To accommodate two 40-mm wide I/O modules for the hot-swapping function To accommodate one 80-mm wide I/O module for the hot-swapping function redundancy bundle Comprising two IM 153-2 High Feature modules and one IM 153/IM 153 bus module 6ES7 15-7HA00-0XA0 6ES7 15-7HB00-0XA0 6ES7 15-7HC00-0XA0 6ES7153-2AR03-0XA0 SIMATIC DP DIN rail for Accommodates up to 5 bus modules; for hot-swapping function Length: 483 mm (1 ) Length: 530 mm Length: 620 mm Length: 2000 mm SIMATIC S7-300 mounting rail Length: 160 mm Length: 480 mm (1 ) Length: 530 mm Length: 830 mm Length: 2000 mm S7 Manual Collection Electronic manuals on DVD, multi-language: S7-200, TD 200, S7-300, M7-300, C7, S7-400, M7-400, STEP 7, Engineering Tools, Runtime Software, SIMATIC DP (Distributed I/O), SIMATIC HMI (Human Machine Interface), SIMATIC NET (Industrial Communication) S7 Manual Collection, update service for 1 year Scope of delivery: Current DVD "S7 Manual Collection" and the three subsequent updates 6ES7 15-1GA00-0XA0 6ES7 15-1GF30-0XA0 6ES7 15-1GG30-0XA0 6ES7 15-1GC00-0XA0 6ES7 30-1AB60-0AA0 6ES7 30-1AE80-0AA0 6ES7 30-1AF30-0AA0 6ES7 30-1AJ30-0AA0 6ES7 30-1BC00-0AA0 6ES7 8-8XC01-8YE0 6ES7 8-8XC01-8YE2 /14
Interface modules IM 153-4 PN To connect to PROFINET IO (via copper line, RJ45) as an IO device 2 versions: - IM 153-4 PN STANDARD - IM 153-4 PN HIGH FEATURE: supports, in contrast to the STANDARD version, the operation of PROFIsafe F and HART modules Integrated 2-port switch 12 modules per station Usable I/O quantity structure: 12 bytes each Active bus backplane to hot-swap modules available as an option Baud rate 10 Mbit/s / 100 Mbit/s (autonegotiation / full duplex) I&M functions in accordance with PROFIBUS International guideline order no. 3.502, Version V1.1 Note: Micro Memory Card with at least 64 KB required if not all the stations in the network support LLDP (Link Layer Discovery Protocol; proximity detection). Technical specifications 6ES7 153-4AA01-0XB0 6ES7 153-4BA00-0XB0 General information Vendor identification (VendorID) 002AH 002AH Device identifier (DeviceID) 0302H 0302H Supply voltage 24 V DC permissible range, lower limit (DC) 20.4 V 20.4 V permissible range, upper limit (DC) 28.8 V 28.8 V permissible range (ripple included), 20.4 V 18.5 V lower limit (DC) permissible range (ripple included), upper limit (DC) 28.8 V 30.2 V External protection for supply cables (recommendation) In a construction with grounded reference potential, a fuse is necessary for redundant interface modules (Recommendation: 2.5 A) In a construction with grounded reference potential, a fuse is necessary for redundant interface modules (Recommendation: 2.5 A) Mains buffering Mains/voltage failure stored energy 5ms 5ms time Input current Current consumption, max. 600 ma 600 ma Inrush current, typ. 4A 4A I²t 0.0 A² s 0.0 A² s Output voltage Rated value, 5 V DC Output current for backplane bus (5 V DC), max. 1.5 A 1.5 A Power losses Power loss, typ. 6W; Typical 6W; Typical Address area Addressing volume Outputs 12 byte 12 byte Inputs 12 byte 672 byte; Extended HART user data Hardware configuration Number of modules per DP slave interface, max. 12 12 /15
Interface modules IM 153-4 PN Technical specifications (continued) 6ES7 153-4AA01-0XB0 6ES7 153-4BA00-0XB0 Communication functions Bus protocol/transmission protocol PN IO PN IO Interrupts/diagnostics/ status information Diagnostics indication LED Connection to network LINK (green) Transmit/receive RX/TX (yellow) Isolation Isolation checked with 500 V DC Between Profinet and 24 V supply: 1500 V AC Between functional grounding and 24 V supply: 500 V DC Degree and class of protection IP20 Ambient conditions Operating temperature Min. 0 C 0 C max. 60 C 60 C Air pressure Operating altitude above sea level, 2 000 m 2 000 m max. Dimensions Width 40 mm 40 mm Height 125 mm 125 mm Depth 118 mm 118 mm Weight Weight, approx. 215 g; approx. 215 g Ordering data Order No. Order No. IM 153-4 PN interface module S7 Manual Collection 6ES7 8-8XC01-8YE0 I/O device to connect an to PROFINET Standard 6ES7 153-4AA01-0XB0 High Feature 6ES7 153-4BA00-0XB0 Bus modules for To accommodate a power supply 6ES7 15-7HA00-0XA0 and an IM 153 module for the hotswapping function during RUN, incl. bus module cover To accommodate two 40-mm wide 6ES7 15-7HB00-0XA0 I/O modules for the hot-swapping function To accommodate one 80-mm wide 6ES7 15-7HC00-0XA0 I/O module for the hot-swapping function SIMATIC Micro Memory Card 64 KB 1) 6ES7 53-8LF20-0AA0 SIMATIC DP DIN rail for Accommodates up to 5 bus modules; for hot-swapping function Length: 483 mm (1 ) 6ES7 15-1GA00-0XA0 Length: 530 mm 6ES7 15-1GF30-0XA0 Length: 620 mm 6ES7 15-1GG30-0XA0 Length: 2 000 mm 6ES7 15-1GC00-0XA0 SIMATIC S7-300 mounting rail Length: 160 mm 6ES7 30-1AB60-0AA0 Length: 480 mm (1 ) 6ES7 30-1AE80-0AA0 Length: 530 mm 6ES7 30-1AF30-0AA0 Length: 830 mm 6ES7 30-1AJ30-0AA0 Length: 2000 mm 6ES7 30-1BC00-0AA0 Electronic manuals on DVD, multi-language: S7-200, TD 200, S7-300, M7-300, C7, S7-400, M7-400, STEP 7, Engineering Tools, Runtime Software, SIMATIC DP (Distributed I/O), SIMATIC HMI (Human Machine Interface), SIMATIC NET (Industrial Communication) S7 Manual Collection 6ES7 8-8XC01-8YE2 update service for 1 year Scope of delivery: Current DVD "S7 Manual Collection" and the three subsequent updates Industrial Ethernet FC RJ45 Plug 180 RJ45 plug connector for Industrial Ethernet with a rugged metal housing and integrated insulation displacement contacts for connecting Industrial Ethernet FC installation cables; with 180 cable outlet 1 unit 6GK1 01-1BB10-2AA0 10 units 6GK1 01-1BB10-2AB0 50 units 6GK1 01-1BB10-2AE0 Industrial Ethernet FastConnect installation cables FastConnect standard cable 6XV1 840-2AH10 FastConnect trailing cable 6XV1 840-3AH10 FastConnect marine cable 6XV1 840-4AH10 Industrial Ethernet FastConnect Stripping Tool 6GK1 01-1GA00 1) To operate the IM153-4, an MMC is required with at least 64 KB memory. Cards with higher memory capacity may also be used. /16
SIPLUS interface modules SIPLUS IM 153-1/153-2 Note: SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme specific information was added. SIPLUS IM 153-1 SIPLUS IM 153-2 SIPLUS IM 153-2 Order No. 6AG1 153-1AA03-2XB0 6AG1 153-2BA02-2XY0 6AG1 153-2BA02-7XB0 Order number based on 6ES7 153-1AA03-0XB0 6ES7 153-2BA02-0XB0 6ES7 153-2BA02-0XB0 Ambient temperature range -40...+70 C Start-up temperature -25 C -25... +60 C -40... +70 C Start-up temperature -25 C Compliant with the standards for electronic equipment used on rolling stock (EN 50155, temperature T1, category 1). No No Conformal coating Technical data Coating of the printed circuit boards and the electronic components The technical data of the standard product applies except for the ambient conditions. SIPLUS bus module for accommodating a PS and an IM 153 for accommodating two 40 mm wide I/O modules Order No. 6AG1 15-7HA00-2XA0 6AG1 15-7HB00-7XA0 Order number based on 6ES7 15-7HA00-0XA0 6ES7 15-7HB00-0XA0 Ambient temperature range -40... +70 C -40... +70 C Compliant with the standards for electronic equipment used on rolling stock (EN 50155, temperature T1, category 1). No Conformal coating Technical data Coating of the printed circuit boards and the electronic components The technical data of the standard product applies except for the ambient conditions. SIPLUS bus module for accommodating an 80 mm module for accommodating two IM 153-2 Order No. 6AG1 15-7HC00-2XA0 6AG1 15-7HD10-2XA0 Order number based on 6ES7 15-7HC00-0XA0 6ES7 15-7HD10-0XA0 Ambient temperature range -40... +70 C -40... +70 C Compliant with the standards for electronic equipment used on rolling stock (EN 50155, temperature T1, category 1). No Conformal coating Technical data Coating of the printed circuit boards and the electronic components The technical data of the standard product applies except for the ambient conditions. /17
SIPLUS interface modules SIPLUS IM 153-1/153-2 (continued) Ambient conditions Relative humidity Biologically active substances, compliance with EN 60721-3-3 Chemically active substances, compliance with EN 60721-3-3 Mechanically active substances, compliance with EN 60721-3-3 Air pressure (depending on the highest positive temperature range specified) For technical documentation on SIPLUS, see: http://www.siemens.com/siplus-extreme 100%, condensation/frost permissible. No commissioning if condensation present. Class 3B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3C4 incl. salt spray in accordance with EN60068-2-52 (degree of severity 3). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation! 1 080... 75 hpa (-1 000... +2 000 m) see ambient temperature range 75... 658 hpa (+2 000... +3 500 m) derating 10 K 658... 540 hpa (+3 500... +5 000 m) derating 20 K Ordering data IM 153-1 interface module Slave interface for connecting an to PROFIBUS DP Standard temperature range IM 153-2 interface module Slave interface for connecting an to PROFIBUS DP; also for use in redundant systems High Feature, -25... +60 C High Feature, -40... +70 C Active IM 153/IM 153 bus module For two IM 153-2 High Feature modules for designing redundant systems Bus module for To accommodate a power supply and an IM 153 for the hot-swapping function during RUN, incl. bus module cover To accommodate two 40 mm wide I/O modules for the hot-swapping function To accommodate one 80 mm wide I/O module for the hot swapping function Order No. 6AG1 153-1AA03-2XB0 6 AG1 153-2BA02-2XY0 6 AG1 153-2BA02-7XB0 6 AG1 15-7HD10-2XA0 6AG1 15-7HA00-2XA0 6AG1 15-7HB00-7XA0 6AG1 15-7HC00-2XA0 See SIMATIC IM 153-1/153-2, page /14 /18
SIPLUS interface modules SIPLUS IM 153-4 PN IO For connection of as IO Device to PROFINET IO (copper, RJ-45) 2 versions: - IM 153-4 PN STANDARD - IM 153-4 PN HIGH FEATURE: additionally to the STANDARD version, operation of PROFIsafe F and HART modules Integrated 2-port switch 12 modules per station Usable I/O quantity structure: 12 bytes each Active backplane bus for hot swapping of modules optionally available Baud rate 10 Mbit/s / 100 Mbit/s (Autonegotiation/Full Duplex) I&M functions according to PNO-Guideline Order-No. 3.502, Version V1.1 Notes: Micro Memory Card with min. 64 KB required if not all participants in the network support LLDP (Link Layer Discovery Protocol; neighbor detection). SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme-specific information was added. SIPLUS ET 200 M IM 153-4 PN Order number 6AG1 153-4AA01-7XB0 Order No. based on 6ES7 153-4AA01-0XB0 Ambient temperature range -25 C... + 70 C Conformal coating Coating of the printed circuit boards and the electronic components Technical data The technical data of the standard product applies except for the environmental conditions. Ambient conditions Relative humidity 5 100 % Condensation permissible Biologically active substances Conformity with EN 60721-3-3, Class 3B2 mold and fungal spores (except fauna) Chemically active substances Conformity with EN 60721-3-3, Class 3C4 incl. salt mist and ISA S71.04 severity level G1; G2; G3; GX 1)2) Mechanically active substances Conformity with EN 60721-3-3, Class 3S4 including conductive sand, dust 2) Air pressure (depending on the highest positive temperature range specified) 1) ISA-S71.04 severity level GX: Long-term load: SO 2 < 4.8 ppm; H 2 S <. ppm; Cl < 0.2 ppm; HCl < 0.66 ppm; HF < 0.12 ppm; NH < 4 ppm; O 3 < 0.1 ppm; NOX < 5.2 ppm Limit value (max. 30 min/d): SO 2 < 17.8 ppm; H2S < 4.7 ppm; Cl < 1.0 ppm; HCl < 3.3 ppm; HF < 2.4 ppm; NH < 247 ppm; O 3 < 1.0 ppm; NOX < 10.4 ppm 2) The supplied plug covers must remain in place over the unused interface when operated in atmospheres containing corrosive gases! The technical documentation on SIPLUS can be found here: http://www.siemens.com/siplus-extreme Ordering data SIPLUS ET 200 M interface connection IM 153-4 PN (extended temperature range and medial exposure) IO Device to connect an to PROFINET 1) 1080... 75 hpa (-1000 +2000 m) See ambient temperature range 75... 658 hpa (+2000... +3500 m) derating 10 K 658 540 hpa (+3500 +5000 m) derating 20 K Order No. 6AG1 153-4AA01-7XB0 See SIMATIC interface module IM 153-4 PN, page /16 1) To operate the IM153-4, an MMC is required with at least 64 KB memory. Cards with higher memory capacity may also be used. /1
I/O modules Digital/analog modules Digital modules Analog modules Digital inputs/outputs For flexible adaptation of the controller to the respective task For connecting digital sensors and actuators For further information, see SIMATIC S7-300, chapter 5. Analog inputs and outputs For solving even more complex tasks with analog process signals For connecting analog actuators and sensors without additional measuring amplifiers For further information, see SIMATIC S7-300, chapter 5. /200
I/O modules Analog input module with HART Can only be plugged into with IM 153-2 and IM 153-2 FO 8 AI HART Redundancy switching Firmware update HART minor variables Technical specifications 6ES7 331-7TF01-0AB0 Supply voltage Load voltage L+ Rated value (DC) 24 V Reverse polarity protection Input current from load voltage L+ (without load), 20 ma max. from backplane bus 5 V DC, max. 120 ma Power losses Power loss, typ. 1.5 W Analog inputs Number of analog inputs 8 permissible input current for current 40 ma input (destruction limit), max. Input ranges (rated values), currents 0 to 20 ma Cable length Cable length, shielded, max. 800 m Analog value creation Measurement principle Sigma Delta Integrations and conversion time/ resolution per channel Resolution with overrange 16 bit (bit including sign), max. Integration time, parameterizable Integration time, ms 20 ms@50 Hz/ 16.6 ms@60 Hz/ 100 ms@100 Hz Interference voltage suppression 60 / 50 / 10 Hz for interference frequency f1 in Hz Encoder Connection of signal encoders for current measurement as 2-wire transducer for current measurement as 4-wire transducer 6ES7 331-7TF01-0AB0 Errors/accuracies Operational limit in overall temperature range Current, relative to input area +/- 0,15 % Basic error limit (operational limit at 25 C) Current, relative to input area +/- 0,1 % Isochronous mode Isochronous operation (application No synchronized up to terminal) Interrupts/diagnostics/ status information Alarms Diagnostic alarm Limit value alarm Diagnostic messages Diagnostic information readable Galvanic isolation Galvanic isolation analog inputs between the channels No between the channels, in groups of 8 between the channels and the backplane bus Isolation Isolation checked with 500 Connection method required front connector 20-pin Dimensions Width 40 mm Height 125 mm Depth 117 mm Weight Weight, approx. 205 g /201
I/O modules Analog input module with HART Ordering data Order No. Order No. SM 331 HART 6ES7 331-7TF01-0AB0 analog input module 8 inputs, 0/4 20 ma, HART for with IM 153-2 interface module Front connectors 20-pin, with screw contacts -1 unit 6ES7 32-1AJ00-0AA0-100 units 6ES7 32-1AJ00-1AB0 20-pin, with spring contacts -1 unit 6ES7 32-1BJ00-0AA0-100 units 6ES7 32-1BJ00-1AB0 LK 33 cable guide 6ES7 33-4AA00-0AA0 Mandatory for operation in hazardous areas SIMATIC DP mounting rail for For mounting of up to 5 bus modules for Length: 483 mm (1") 6ES7 15-1GA00-0XA0 Length: 530 mm 6ES7 15-1GF30-0XA0 SIMATIC S7-300 mounting rail Length: 160 mm 6ES7 30-1AB60-0AA0 Length: 480 mm (1") 6ES7 30-1AE80-0AA0 Length: 530 mm 6ES7 30-1AF30-0AA0 Length: 830 mm 6ES7 30-1AJ30-0AA0 Length: 2000 mm 6ES7 30-1BC00-0AA0 Label cover (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM Labeling strips (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM Labeling sheets for machine printing for modules with 20-pin front connector, DIN A4, for printing with laser printer; 10 units petrol light beige yellow red 6ES7 32-2XY00-0AA0 6ES7 32-2XX00-0AA0 6ES7 32-2AX00-0AA0 6ES7 32-2BX00-0AA0 6ES7 32-2CX00-0AA0 6ES7 32-2DX00-0AA0 /202
I/O modules Analog output module with HART For plugging into exclusively with IM 153-2 and IM 153-2 FO 8 AO HART Redundancy switching Firmware update HART minor variables Technical specifications 6ES7 332-8TF01-0AB0 Supply voltage Load voltage L+ Rated value (DC) 24 V Input current from load voltage L+ (without load), 350 ma max. from backplane bus 5 V DC, max. 110 ma Power losses Power loss, typ. 6W Analog outputs Number of analog outputs 8 Current output, no-load voltage, max. 24 V Output ranges, current 0 to 20 ma -20 to +20 ma No 4 to 20 ma Load impedance (in rated range of output) with current outputs, max. 750 with current outputs, inductive load, 10 mh max. Cable length Cable length, shielded, max. 800 m Analog value creation Integrations and conversion time/ resolution per channel Resolution with overrange 16 bit (bit including sign), max. Settling time for resistive load 0.1 ms for inductive load 0.5 ms 6ES7 332-8TF01-0AB0 Errors/accuracies Operational limit in overall temperature range Current, relative to output area +/- 0,2 % Basic error limit (operational limit at 25 C) Current, relative to output area +/- 0,1 % Interrupts/diagnostics /status information Substitute values connectable Alarms Diagnostic alarm Diagnostic messages Diagnostic information readable Galvanic isolation Galvanic isolation analog outputs between the channels and the backplane bus Isolation Isolation checked with 500 V DC Connection method required front connector 20-pin Dimensions Width 40 mm Height 125 mm Depth 117 mm Weight Weight, approx. 220 g /203
I/O modules Analog output module with HART Ordering data Order No. Order No. SM 332 HART 6ES7 332-8TF01-0AB0 analog output module HART analog output, 8 outputs, 0/4 20 ma, HART for with IM 153-2 Front connector 20-pin, with screw contacts -1 item 6ES7 32-1AJ00-0AA0-100 items 6ES7 32-1AJ00-1AB0 20-pin, with spring-loaded terminals -1 item 6ES7 32-1BJ00-0AA0-100 items 6ES7 32-1BJ00-1AB0 LK 33 cable guide 6ES7 33-4AA00-0AA0 Mandatory for operation in hazardous areas SIMATIC DP mounting rail for For mounting of up to 5 bus modules for Length: 483 mm 6ES7 15-1GA00-0XA0 Length: 530 mm 6ES7 15-1GF30-0XA0 SIMATIC S7-300 mounting rail Length: 160 mm 6ES7 30-1AB60-0AA0 Length: 480 mm 6ES7 30-1AE80-0AA0 Length: 530 mm 6ES7 30-1AF30-0AA0 Length: 830 mm 6ES7 30-1AJ30-0AA0 Length: 2000 mm 6ES7 30-1BC00-0AA0 Label cover 6ES7 32-2XY00-0AA0 (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM Labeling strips 6ES7 32-2XX00-0AA0 (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM S7 Manual Collection Electronic manuals on DVD, multi-language: S7-200, TD 200, S7-300, M7-300, C7, S7-400, M7-400, STEP 7, Engineering Tools, Runtime Software, SIMATIC DP (Distributed I/O), SIMATIC HMI (Human Machine Interface), SIMATIC NET (Industrial Communication) S7 Manual Collection update service for 1 year Scope of delivery: Current DVD "S7 Manual Collection" and the three subsequent updates Labeling sheets for machine printing for modules with 20-pin front connector, DIN A4, for printing with laser printer; 10 units petrol light beige yellow red 6ES7 8-8XC01-8YE0 6ES7 8-8XC01-8YE2 6ES7 32-2AX00-0AA0 6ES7 32-2BX00-0AA0 6ES7 32-2CX00-0AA0 6ES7 32-2DX00-0AA0 /204
I/O modules Ex-analog input module with HART For connecting HART devices in hazardous areas Can only be plugged into 2 AI HART, Ex 2 inputs in 2 channel groups (single-channel isolation) Measurement type/range can be selected for each channel Diagnostics and diagnostic alarm parameterizable Technical specifications 6ES7 331-7TB00-0AB0 Supply voltage Load voltage L+ Rated value (DC) 24 V Reverse polarity protection Input current from backplane bus 5 V DC, max. 100 ma from supply voltage L+, max. 180 ma Output voltage Power supply to the transmitters present Rated value (DC) 15 V; at 22 ma short-circuit proof ; approx. 30 ma No-load voltage (DC) 2.6 V Power losses Power loss, typ. 4.5 W Analog inputs Number of analog inputs 2 permissible input current for current 40 ma input (destruction limit), max. Input ranges Current Input ranges (rated values), currents 0 to 20 ma Input resistance (0 to 20 ma) 50 4 to 20 ma Input resistance (4 to 20 ma) 50 Cable length Cable length, shielded, max. 400 m Analog value creation Measurement principle Sigma Delta Integrations and conversion time/ resolution per channel Resolution with overrange 16 bit; 10 to 15 bits + sign (bit including sign), max. Integration time, parameterizable Integration time, ms 2.5 / 16.67 / 20 / 100 ms Basic conversion time, including integration time, ms Interference voltage suppression for interference frequency f1 in Hz 2.5 / 16.67 / 20 / 100 (1 channel enabled); 7.5 / 50 / 60 / 300 (2 channels enabled) 10 / 50 / 60 / 400 Hz 6ES7 331-7TB00-0AB0 Encoder Connection of signal encoders for current measurement as 2-wire transducer for current measurement as 4-wire transducer Errors/accuracies Linearity error (relative to input area) +/- 0.01 % Temperature error +/- 0.01 % (relative to input area) Crosstalk between the inputs, min. 130 db Repeat accuracy in settled status at +/- 0.05 % 25 C (relative to input area) Operational limit in overall temperature range Current, relative to input area +/- 0,45 %; From 0/4 to 20 ma Basic error limit (operational limit at 25 C) Current, relative to input area +/- 0,1 %; From 0/4 to 20 ma Interference voltage suppression for f = n x (f1 +/- 1%), f1 = interference frequency Series mode interference 60 db (peak value of interference < rated value of input range), min. Common mode interference, min. 130 db Interrupts/diagnostics/ status information Alarms Diagnostic alarm ; Parameterizable Limit value alarm ; Parameterizable, channels 0 and 1 Diagnostic messages Diagnostic functions ; can be set in parameters, red LED, alarm message Diagnostic information readable Overrange ; Red LED, signal Wire break in signal transmitter ; Red LED, signal cable Short circuit of the signal encoder ; Red LED, signal cable HART communication active ; green LED (H) Diagnostics indication LED Group error SF (red) Channel error indicator F (red) /205
I/O modules Ex-analog input module with HART Technical specifications (continued) Ordering data Order No. Ex(i) characteristics Module for Ex(i) protection Max. values of input circuits (per channel) Co (permissible external capacity), max. Io (short-circuit current), max. Lo (permissible external inductivity), max. Po (power of load), max. Uo (output no-load voltage), max. Um (fault voltage), max. Ta (permissible ambient temperature), max. Galvanic isolation between the channels and backplane bus Galvanic isolation analog inputs Galvanic isolation analog inputs 6ES7 331-7TB00-0AB0 62 nf 6.1 ma 3mH 511 mw 26 V 250 V; DC 0.6 C SM 331 HART analog input module 2 inputs, 0/4 20 ma, HART for with IM 153-2 interface module Front connector 1) 20-pin, with screw contacts 1 unit 100 units LK 33 cable guide Mandatory for operation in hazardous areas SIMATIC DP mounting rail for For mounting of up to 5 bus modules for Length: 483 mm Length: 530 mm 6ES7 331-7TB00-0AB0 6ES7 32-1AJ00-0AA0 6ES7 32-1AJ00-1AB0 6ES7 33-4AA00-0AA0 6ES7 15-1GA00-0XA0 6ES7 15-1GF30-0XA0 Galvanic isolation analog outputs between the channels between the channels and the load voltage L+ Permissible potential difference between the inputs (UCM) 60 V DC/30 V AC Isolation tested with Channels against backplane bus 1500 V AC and load voltage L+ Channels among one another 1500 V AC Load voltage L+ against backplane 500 V DC bus Standards, approvals, certificates FM approval Available soon Use in hazardous areas Type of protection acc. to EN 50020 [EEx ib] IIC (CENELEC) Type of protection acc. to FM Class I, Division 2, Group A, B, C, D T4; Class I, Zone 2, Group IIC T4 Test number KEMA KEMA 7; ATEX303 X Type of protection acc. to KEMA II3 (2) G Eex na [ib] IIC T4 Ambient conditions Operating temperature max. 60 C SIMATIC S7-300 mounting rail Length: 160 mm Length: 480 mm (1") Length: 530 mm Length: 830 mm Length: 2000 mm Label cover (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM Labeling strips (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM Labeling sheets for machine printing for modules with 20-pin front connector, DIN A4, for printing with laser printer; 10 units petrol light beige yellow red 6ES7 30-1AB60-0AA0 6ES7 30-1AE80-0AA0 6ES7 30-1AF30-0AA0 6ES7 30-1AJ30-0AA0 6ES7 30-1BC00-0AA0 6ES7 32-2XY00-0AA0 6ES7 32-2XX00-0AA0 6ES7 32-2AX00-0AA0 6ES7 32-2BX00-0AA0 6ES7 32-2CX00-0AA0 6ES7 32-2DX00-0AA0 Dimensions Width 40 mm Height 125 mm Depth 120 mm Weight Weight, approx. 260 g 1) A connector with spring-loaded terminals cannot be used if the cable guide is used. /206
I/O modules Ex-analog output module with HART For using HART devices in hazardous areas. Can only be plugged into 2 AO HART, Ex 2 current outputs in 2 channel groups (single-channel isolation) Output type and range can be selected for each channel Diagnostics and diagnostic alarm parameterizable Read-back capability of the analog outputs Technical specifications 6ES7 332-5TB00-0AB0 Supply voltage Load voltage L+ Rated value (DC) 24 V Reverse polarity protection Input current from backplane bus 5 V DC, max. 100 ma from supply voltage L+, max. 150 ma Power losses Power loss, typ. 3.5 W Analog outputs Number of analog outputs 2 Voltage output, short-circuit protection Current output, no-load voltage, max. 1 V Cycle time (all channels) max. 5ms Output ranges, current 0 to 20 ma 4 to 20 ma Connection of actuators for current output 2-conductor connection Load impedance (in rated range of output) with current outputs, max. 650 with current outputs, inductive load, 7.5 mh max. Destruction limits against externally applied voltages and currents Voltages at the outputs towards max. 17 V / -0.5 V MANA Current, max. 60 ma / -1 A Cable length Cable length, shielded, max. 400 m Analog value creation Integrations and conversion time/ resolution per channel Resolution with overrange 12 bit; Output value; 8 bit (+ sign) (bit including sign), max. read back value Conversion time (per channel) 40 ms Settling time for resistive load 2.5 ms for capacitive load 4ms for inductive load 2.5 ms 6ES7 332-5TB00-0AB0 Errors/accuracies Output ripple (based on output area, +/- 0.02 % bandwidth 0 to 50 khz) Linearity error (relative to output area) +/- 0.03 % Temperature error +/- 0.01 % (relative to output area) Crosstalk between the outputs, min. 130 db Repeat accuracy in settled status +/- 0.005 % at 25 C (relative to output area) Operational limit in overall temperature range Current, relative to output area +/- 0,55 % Basic error limit (operational limit at 25 C) Current, relative to output area +/- 0,15 % Interrupts/diagnostics/ status information Substitute values connectable ; Parameterizable Alarms Diagnostic alarm ; Parameterizable Diagnostic messages Diagnostic functions ; Parameterizable Diagnostic information readable Diagnostics Overrange Wire break ; as of output value > 0.5 ma Wire break in actuator cable HART communication active ; green LED (H) Diagnostics indication LED Group error SF (red) ; Additional group message per channel Channel error indicator F (red) ; per channel /207
I/O modules Ex-analog output module with HART Technical specifications (continued) Ordering data Order No. 6ES7 332-5TB00-0AB0 Ex(i) characteristics Module for Ex(i) protection Max. values of output circuits (per channel) Co (permissible external capacity), 230 nf max. Io (short-circuit current), max. 66 ma Lo (permissible external inductivity), 7.5 mh max. Po (power of load), max. 506 mw Uo (output no-load voltage), max. 1 V Um (fault voltage), max. 60 V; DC Ta (permissible ambient 60 C temperature), max. Galvanic isolation between the channels and backplane bus Galvanic isolation analog outputs Galvanic isolation analog outputs between the channels between the channels and the load voltage L+ Permissible potential difference between the outputs (UCM) 60 V DC/30 V AC between M internally and the outputs 60 V DC/30 V AC Isolation tested with Channels against backplane bus 1500 V AC and load voltage L+ Channels among one another 1500 V AC Load voltage L+ against backplane 500 V DC bus Standards, approvals, certificates FM approval Available soon Use in hazardous areas Type of protection acc. to EN 50020 [EEx ib] IIC (CENELEC) Type of protection acc. to FM Class I, Division 2, Group A, B, C, D T4; Class I, Zone 2, Group IIC T4 Test number KEMA 7 ATEX 235 X Type of protection acc. to KEMA II3 (2) G Eex na [ib] IIC T4 Dimensions Width 40 mm Height 125 mm Depth 120 mm Weight Weight, approx. 280 g SM 332 HART analog output module HART analog output, 8 outputs, 0/4 20 ma, HART for with IM 153-2 Front connectors 20-pin, with screw contacts 1 unit 100 units LK 33 cable guide Mandatory for operation in hazardous areas SIMATIC DP mounting rail for For mounting of up to 5 bus modules for Length: 483 mm (1") Length: 530 mm SIMATIC S7-300 mounting rail Length: 160 mm Length: 480 mm (1") Length: 530 mm Length: 830 mm Length: 2000 mm Label cover (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM Labeling strips (10 units, spare part) for signal modules (not 32-channel modules), function modules and CPU 312 IFM Labeling sheets for machine printing for modules with 20-pin front connector, DIN A4, for printing with laser printer; 10 units petrol light beige yellow red S7 Manual Collection Electronic manuals on DVD, multi-language: S7-200, TD 200, S7-300, M7-300, C7, S7-400, M7-400, STEP 7, Engineering Tools, Runtime Software, SIMATIC DP (Distributed I/O), SIMATIC HMI (Human Machine Interface), SIMATIC NET (Industrial Communication) 6ES7 332-5TB00-0AB0 6ES7 32-1AJ00-0AA0 6ES7 32-1AJ00-1AB0 6ES7 33-4AA00-0AA0 6ES7 15-1GA00-0XA0 6ES7 15-1GF30-0XA0 6ES7 30-1AB60-0AA0 6ES7 30-1AE80-0AA0 6ES7 30-1AF30-0AA0 6ES7 30-1AJ30-0AA0 6ES7 30-1BC00-0AA0 6ES7 32-2XY00-0AA0 6ES7 32-2XX00-0AA0 6ES7 32-2AX00-0AA0 6ES7 32-2BX00-0AA0 6ES7 32-2CX00-0AA0 6ES7 32-2DX00-0AA0 6ES7 8-8XC01-8YE0 S7 Manual Collection update service for 1 year 6ES7 8-8XC01-8YE2 Scope of delivery: Current DVD "S7 Manual Collection" and the three subsequent updates /208
I/O modules SIPLUS analog input module with HART Can only be plugged into with IM 153-2 and IM 153-2 FO 8 AI HART Redundant connection Firmware update HART secondary variables Note: SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme specific information was added. SIPLUS analog input module with HART Order No. 6AG1 331-7TF01-7AB0 6AG1 331-7TF01-4AB0 Order No. based on 6ES7 331-7TF01-0AB0 6ES7 331-7TF01-0AB0 Ambient temperature range -25 C +70 C 0 C +60 C Conformal coating Coating of the printed circuit boards and the electronic components Technical data The technical data of the standard product applies except for the ambient conditions. Ambient conditions Relative humidity 100%, condensation/frost permissible. No commissioning if condensation present. Biologically active substances, compliance with EN 60721-3-3 Chemically active substances, compliance with EN 60721-3-3 Mechanically active substances, compliance with EN 60721-3-3 Air pressure (depending on the highest positive temperature range specified) For technical documentation on SIPLUS, see: http://www.siemens.com/siplus-extreme Class 3B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3C4 incl. salt spray in accordance with EN60068-2-52 (degree of severity 3). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation! 1 080...75 hpa (-1 000 +2 000 m) See ambient temperature range 75 658 hpa (+2 000 +3 500 m) Derating 10 K 658...540 hpa (+3 500... +5 000m) Derating 20 K Ordering data Order No. SM 331 HART analog input module (extended temperature range and medial exposure) 8 inputs, 0/4 20 ma, HART for with IM 153-2 interface module 8 inputs, 0/4 20 ma, HART for with IM 153-2 interface module; medial exposure only 6AG1 331-7TF01-7AB0 6AG1 331-7TF01-4AB0 See SIMATIC SM 331 analog module with HART, page /202 /20
I/O modules SIPLUS analog output module with HART Pluggable exclusively in with IM 153-2 and IM 153-2 FO 8 AO HART Redundant connection Firmware update HART secondary variables Note: SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme specific information was added. SIPLUS S7-300 SM332 8AO HART Order No. 6AG1 332-8TF01-2AB0 6AG1 332-8TF01-4AB0 Order No. based on 6ES7 332-8TF01-0AB0 6ES7 332-8TF01-0AB0 Ambient temperature range -25 C +60 C 0 C +60 C Conformal coating Coating of the printed circuit boards and the electronic components Technical data The technical data of the standard product applies except for the ambient conditions. Ambient conditions Relative humidity 100%, condensation/frost permissible. No commissioning if condensation present. Biologically active substances, compliance with EN 60721-3-3 Chemically active substances, compliance with EN 60721-3-3 Mechanically active substances, compliance with EN 60721-3-3 Air pressure (depending on the highest positive temperature range specified) For technical documentation on SIPLUS, see: http://www.siemens.com/siplus-extreme Class 3B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3C4 incl. salt spray in accordance with EN60068-2-52 (degree of severity 3). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation! 1,080...75 hpa (-1,000... +2,000 m) See ambient temperature range 75 658 hpa (+2,000 +3,500 m) Derating 10 K 658...540 hpa (+3 500... +5 000m) Derating 20K Ordering data SIPLUS SM 332 analog output module with HART (medial exposure) HART analog output, 8 outputs, 0/4-20 ma, HART for, with IM 153-2 Additionally with expanded temperature range Order No. 6AG1 332-8TF01-4AB0 6AG1 332-8TF01-2AB0 See SIMATIC SM 332 analog output module with HART, page /204 /210
I/O modules SIPLUS Ex analog input module with HART For connecting HART devices in hazardous areas. Can only be plugged into 2 AI HART, Ex 2 inputs in 2 channel groups (single-channel isolation) Measurement type/range can be selected for each channel Programmable diagnostics and diagnostic interrupt Note: SIPLUS extreme products are based on Siemens Industry standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme specific information was added. SIPLUS Ex analog input module with HART Order No. 6AG1 331-7TB00-7AB0 6AG1 331-7TB00-4AB0 Order number based on 6ES7 331-7TB00-0AB0 6ES7 331-7TB00-0AB0 Ambient temperature range -25 C +70 C 0 C +60 C Conformal coating Coating of the printed circuit boards and the electronic components Technical data The technical data of the standard product applies except for the ambient conditions. Ambient conditions Relative humidity 100%, condensation/frost permissible. No commissioning if condensation present. Biologically active substances, compliance with EN 60721-3-3 Chemically active substances, compliance with EN 60721-3-3 Mechanically active substances, compliance with EN 60721-3-3 Air pressure (depending on the highest positive temperature range specified) For technical documentation on SIPLUS, see: http://www.siemens.com/siplus-extreme Class 3B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3C4 incl. salt spray in accordance with EN60068-2-52 (degree of severity 3). The supplied plug covers must remain in place over the unused interfaces during operation! Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation! 1 080...75 hpa (-1 000 +2 000 m) See ambient temperature range 75 658 hpa (+2 000 +3 500 m) derating 10 K 658...540 hpa (+3 500... +5 000m) derating 20K Ordering data SM 331 HART analog input module (extended temperature range and medial exposure) 2 inputs, 0/4 to 20 ma, HART for with IM 153-2 interface module 2 inputs, 0/4 to 20 ma, HART for with IM 153-2 interface module; medial exposure only Order No. 6AG1 331-7TB00-7AB0 6AG1 331-7TB00-4AB0 See SIMATIC Ex-analog input module with HART, page /206 /211
Function modules Function modules unburden the CPU of work-intensive tasks such as counting, positioning and controlling Module spectrum Counter modules Positioning modules for rapid traverse and creep speed drives Positioning modules for stepper motors Positioning modules for servo motors Positioning and continuous path modules SSI position detection modules Electronic cam controllers High-speed Boolean processor Control modules Function modules Counting Positioning of rapid traverse and creep speed drives of stepper motors of servo motors Position and path control SSI position detection Electronic cam control High speed logic operation Controlling Weighing and proportioning electronics 1) Not for FM 350-1 counter module FM 350-2 counter module FM 351 positioning module FM 353 positioning module FM 354 positioning module FM 357-2 path and position control module 1) SM 338 POS input modules FM352 electronic cam controller FM 352-5 high speed Boolean processor FM 355 controller module FM 355-2 temperature controller module SIWAREX /212
(continued) Applicability with distributed I/O device Almost all function modules can be used in the distributed I/O device. In doing so, the following details must be observed: Function modules For plugging in behind IM 153-1 (6ES7 153-1AA03-0XB0) For plugging in behind IM 153-2 (6ES7 153-2BA02-0XB0) For plugging in behind IM 153-2 FO (6ES7 153-2BB00-0XB0) configurable -- not configurable 1) Configuration using the meta-knowledge integrated into STEP 7 (in hardware catalog under PROFIBUS DP > ET200M > IM 153-1 / IM 153-2 or PROFINET IO > I/O > > IM153-4 PN). 2) Configuration using GSD file (after installation of the GSD file configurable from the Hardware Catalog under PROFIBUS DP > Additional field devices > I/O > ET200M). During configuration on the CP 342-5 as DP master, S5 (IM 308C) as DP master or external masters, the GSD file must be configured. 3) Visible and configurable only with the corresponding configuration package in STEP 7. For plugging in behind IM 153-4 PN (6ES7 153-4AA00-0XB0) configurable with Module Order No. STEP 7 1) GSD 2) STEP 7 1) GSD 2) STEP 7 1) GSD 2) STEP 7 1) FM 350-1 6ES7 350-1AH03-0AE0 -- -- -- counter module FM 350-2 6ES7 350-2AH01-0AE0 -- -- -- counter module FM 351 6ES7 351-1AH01-0AE0 -- -- -- positioning module FM 352 6ES7 352-1AH02-0AE0 -- -- -- cam controller FM 352-5 6ES7 352-5AH00-0AE0 3) 3) 3) high speed Boolean processor FM 352-5 6ES7 352-5AH10-0AE0 3) 3) 3) high speed Boolean processor FM 353 6ES7 353-1AH01-0AE0 -- -- -- -- -- positioning module FM 354 6ES7 354-1AH01-0AE0 -- -- -- -- -- positioning module FM 355 C 6ES7 355-0VH10-0AE0 -- -- -- -- controller module FM 355 S 6ES7 355-1VH10-0AE0 -- -- -- -- controller module FM 355-2 C 6ES7 355-2CH00-0AE0 -- -- -- temperature controller module FM 355-2 S 6ES7 355-2SH00-0AE0 -- -- -- temperature controller module SM 338 POS input module 6ES7 338-4BC01-0AB0 Note: Position measurement systems and prefabricated connecting cables for counter and positioning function are offered under SIMODRIVE Sensor and Motion Connect 500. http://www.siemens.com/simatic-technology For further information, see SIMATIC S7-300, chapter 5. /213
Special modules, Communication Special modules Communication The special modules provide the user with functions for diagnostics, as well as commissioning. For further information, see SIMATIC S7-300, chapter 5. Communication boards for data exchange using point-to-point coupling Communication board for the connection of identification systems For further information, see SIMATIC S7-300, chapter 5. /214
ASM 475 The ASM 475 is a low-cost module for connecting the MOBY D, U, SIMATIC RF200, RF300, RF600 and SIMATIC MV400 identification systems to the S7-300 and. Technical specifications Order No. 6GT2 002-0GA10 Product-type designation ASM 475 communication module Suitability for installation Transmission rate at point-to-point 115.2 kbit/s connection serial maximum Interfaces Design of interface for point-to-point RS422 connection Number of readers connectable 2 Design of electrical connection of the backplane bus S7-300 backplane bus of the PROFIBUS interface (according to the head module) the Industrial Ethernet Interface (according to the head module) for supply voltage Screw-type or spring-loaded terminals Version of the interface to the reader for communication Mechanical data Material Color Supply voltage, current consumption, power loss Supply voltage for DC rated value minimum maximum Current consumed at 24 V DC without connected devices typical including connected devices maximum Permitted ambient conditions Ambient temperature during operating Screw-type or spring-loaded terminals Noryl Anthracite 24 V 20 V 30 V 0.1 A 1A 0 60 C during storage -40 +70 C during transport -40 +70 C Protection class IP Resistance against shock According to IEC 61131-2 Resistance against shock 150 m/s² Resistance against vibration 10 m/s² Order No. Product-type designation Design, dimensions and weight Width Height Depth Net weight Type of mounting Cable length for RS 422 interface maximum Product properties, functions, components general Type of display Product function transponder file handler can be addressed Protocol will be supported S7 communication Product functions management, configuration Type of parameterization 6GT2 002-0GA10 ASM 475 communication module 40 mm 125 mm 120 mm 0.2 kg S7-300 rack 1000 m 4 LEDs per reader connection, 2 LEDs for device status Object manager, GSD Type of programming FB 45, FB 55, FC 56 (FC 45/55 with limited functionality) Type of computer-mediated acyclic communication communication Standards, specifications, approvals Verification of suitability CE, FCC, UL/CSA Front connector with screw-type or spring-loaded terminals /215
ASM 475 Ordering data Order No. Order No. ASM 475 communication module 6GT2 002-0GA10 For SIMATIC S7-300 and, parameterizable Front connector (1 x per ASM 475) with screw terminals 6ES7 32-1AJ00-0AA0 with spring-loaded terminals 6ES7 32-1BJ00-0AA0 MOBY U connecting cable pre-assembled, between the ASM 475 and reader, angled connector, PUR material, in the following lengths: 2 m 6GT2 01-4EH20 5 m 6GT2 01-4EH50 10 m 6GT2 01-4EN10 20 m 6GT2 01-4EN20 50 m 6GT2 01-4EN50 MOBY D connecting cable pre-assembled, between ASM 475 and reader D1xS, -pole Sub-D plug, PUR material, CMG approved, suitable for cable carriers, in the following lengths: 5 m 6GT2 41-4EH50 20 m 6GT2 41-4EN20 50 m 6GT2 41-4EN50 SIMATIC RF200 / RF300 / RF600 / MV400 connecting cable pre-assembled, between the ASM 475 and RF200 / RF300 / RF600 / MV400, IP65, straight connector, PUR material, suitable for cable carriers, CMG approval, in the following lengths 1) : 2 m 6GT2 81-4EH20 5 m 6GT2 81-4EH50 Extension cable SIMATIC RF200 / RF300 / RF600 / MV400, PUR material, CMG approval, suitable for cable carriers, straight connector 2 m 6GT2 81-4FH20 5 m 6GT2 81-4FH50 10 m 6GT2 81-4FN10 20 m 6GT2 81-4FN20 50 m 6GT2 81-4FN50 DVD "RFID Systems Software & 6GT2 080-2AA20 Documentation" 1) The connecting cables can be extended using RF300 connecting cables of type 6GT281-4Fxxx. These connecting cables are available in the lengths 2 m, 5 m, 10 m, 20 m and 50 m. /216