.Booklet 1.Booklet Hydraulic Motors
out 2 out
1.Booklet R Geroler Element... 11 Displacements... [15] ** 75 [20] * Speed... Up to 10 RPM Pressure Bar [PSI]... 125 [1800] Cont. 165 [2400] Inter. Torque Nm [lb-in]... 4 [4040] Cont. 520 [4600] Inter. This Char-Lynn spool valve motor with the Geroler torque generating element is economical, efficient, compact, powerful, and is very effective at low flows and high pressure applications. The outer ring of the Geroler element has seven precision machined rollers that provide rolling contact as the six lobe star orbits within the Geroler element. This orbiting slow turning star coupled to the output shaft with a splined drive provides the hydromechanical six to one advantage. Consequently, with this 6 to 1 reduction built into each motor, gear box speed reducers will not be necessary on most applications. ** (Cont.) rating, motor may be run continuously at these ratings. * (Inter.) operation, 10% of every minute. Displacement Size = cubic centimeter per shaft revolution ( cm 3 /r ) 36 [ 2.2] = cubic inch per shaft revolution ( [ in 3 /r ] ) 49 [ 3.0] 66 [ 4.0] 80 [ 4.9] 102 [ 6.2] 131 [ 8.0] 157 [ 9.6] 5 [11.9] 244 [.9] 306 [18.7] 370 [22.6] Flange 2 Bolt (Standard) 82,6 [3.25] Pilot Dia. and 13,59 [.535] Dia. Holes 106,2 [4.18] Dia. B.C. 4 Bolt (Standard) 44,4 [1.75] Pilot Dia. and 3/8-16 Holes 82,6 [3.25] Dia. B.C. 4 Bolt (Standard) 44,4 [1.75] Pilot Dia. and M10 x 1,5 Holes 82,6 [3.25] Dia. B.C. 4 Bolt Magneto 82,6 [3.25] Pilot Dia. and 13,59 [.535] Dia. Holes 106,2 [4.18] Dia. B.C. Output Shaft 1 inch Dia. Straight with Woodruff Key and 1/4-20 Threaded Hole 1 inch Dia. SAE 6B Splined with 1/4-20 Threaded Hole 1 inch Dia. Straight with 7,9 [.31] Dia. Crosshole 11,2 [.44] from End 1 inch Dia. Straight with 10,2 [.40] Dia. Crosshole 15,7 [.62] from End and 1/4-20 Threaded Hole 7/8 inch Dia. SAE B 13 T Splined 1 inch Dia. Tapered with Woodruff Key and Nut 25mm Dia. Straight with 8mm Key and 8mm x 1,2 Threaded Hole 1 inch Dia. Straight with 10,2 [.40] Dia. Crosshole 15,7 [.62] from End and 1/4-20 Threaded Hole (Plated for Corrosion Protection) 1 inch Dia. Tapered with Woodruff Key and Nut, 9,52 [.375] Reduced Length Port Type 7/8- O-ring 1/2- NPTF Manifold (5/16-18 Threads) Manifold (M8 x 1,5 Threads) G 1/2 (BSP) Case Drain No Case Drain 7/16-20 O-ring Port End Cap G 1/4 (BSP) Port End Cap Special Features Available Viton Shaft Seal Reverse Rotation Flange Rotated 90 Corrosion Protected Low Speed Valve Speed Sensor Viton is a Registered Trade Name of Dupont Corp..Booklet 3
out Shaft Seal Low Speed Valving Free Running Motors Corrosion Protected Speed Sensor This high pressure shaft seal has a patented feature which allows the seal lip to follow shaft deflection, and therefore provides better sealing under high side load conditions. Deflection occurs as radial loads are applied to the output shaft. This time proven shaft seal design and construction is the same as that used in the popular Char-Lynn disc valve motors and is available in either buna or Viton. With this shaft seal the motors can withstand high back pressures without an external case drain. The motors can be connected together in series, or parallel to one another. These motors with the low speed valving option provide very low speed while maintaining high torque. Designed to run continuously at up to 200 RPM at standard rated pressures and reduced flows, providing smooth operation at low speeds. Furthermore, they resist slippage and have more momentary load holding ability than the standard motors. Motors with this valving are not intended for low pressure applications ( Bar [600 PSI] Minimum). Shaft side / radial load ratings are not affected by this valving. motors can be ordered with a special Geroler to permit free running of the output shaft. With this special feature, performance might be affected when extreme conditions exist. Overall efficiency may be reduced slightly. motors are available with a corrossion resistant coating for use in an hostile environment. This coating protects the motor from salt water and various chemicals. It is especially effective in marine, food processing, car wash, fishing, and agricultural applications. Shaft plating helps eliminate seal damage caused by these caustic or acid materials on this otherwise unprotected shaft sealing area. Corrosion protected motors are available with just the output shaft plated, or protected with an entire motor exterior coating. The motor is available with a rugged digital sensor for monitoring motor shaft speed. Compatible with vehicle electrical systems, this feature is ideal for applications where speeds need to be accurately known. Catalog Contents Specifications Performance Data Dimensions Product (Mtg., Shafts, and Ports Listed Below) Product Numbers (Standard Units) Shaft Side Load Capacity Dimensions Shafts Dimensions Ports Case Pressure and Case Drain Speed Sensor 16 Dimensions Mtg. Options/Mtg. Kit 17 Fluid Recommendations 18 Model Code (Special* Orders) * Contact your Eaton Representative page 5 6-8 9 10 11 12-13 15-16 4 out
1.Booklet Specifications Static Seal Thrust Bearing Race Backup Washer Thrust Needle Bearing Housing Drive Spacer Plate Geroler Output Shaft Exclusion Seal Pressure Seal Flange Cap Screws Static Seals End Cap View of Geroler Section Specification Data Displ. cm 3 /r [in 3 /r] 36 [2.2] 49 [3.0] 66 [4.0] 80 [4.9] 102 [6.2] 131 [8.0] 157 [9.6] 5 [11.9] 244 [.9] 306 [18.7] Speed (RPM) @ Flow Flow LPM [GPM] Torque Nm [lb-in] Pressure Bar [ PSI] ** * * ** 987 868 805 657 5 401 338 270 215 172 38 45 [12] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 38 53 [] 64 [17] 68 [18] 68 [18] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 58 [517] 78 [687] 81 [721] 108 [952] [1] 4 [1278] 135 [17] 178 [1577] 171 [1511] 226 [98] 222 [68] 301 [2660] 2 [2378] 339 [2996] 320 [30] 378 [3344] 374 [3310] 422 [3735] 423 [37] 4 [4398] [1800] [1800] [1800] [1800] [1800] [1800] [1800] 121 [1750] 1 [1650] 103 [1500] 165 [2400] 165 [2400] 165 [2400] 165 [2400] 165 [2400] 165 [2400] 159 [2300] 5 [2100] 131 [00] [1800] 370 [22.6] 2 57 [15] 76 [20] 442 [3910] 520 [4600] 90 [1300] 1 [1650] Maximum Case Pressure w/o Case Drain 103 Bar [1500 PSI] see page 16 * Maximum intermittent pressure at motor inlet port of 172 Bar [2500 PSI] without regard to Bar [ PSI] and/or back pressure ratings or combination thereof. A simultaneous maximum torque and maximum speed NOT recommended. ** 6B Splined or Tapered shafts are recommended whenever operating above 2 Nm [2500 lb-in] of torque, especially for those applications subject to frequent reversals (see page 12). Bar [ PSI] True pressure difference between inlet port and outlet port. Rating Motor may be run continuously at these ratings. Operation 10% of every minute. Recommended Fluids Premium quality, anti-wear type hydraulic oil with a viscosity of not less than 70 SUS at operating temperature (see page 18). Recommended Maximum System Operating Temp. Is 82 C [180 F] Recommended Filtration per ISO Cleanliness Code, level 18/13 To assure best motor life, run motor for approximately one hour at 30% of rated pressure before application to full load. Be sure motor is filled with fluid prior to any load applications..booklet 5
6 Performance Data [] 3 2 [92] 10 824 [157] 18 815 [221] 25 805 [5] 32 794 [344] 39 781 [3] 53 751 [718] 81 673 [18] 2 1038 [82] 9 1032 [7] 17 1021 [211] 24 1012 [275] 31 1000 [336] 38 988 [464] 52 9 [715] 81 877 [800] [1200] [1600] [2400] 165 36 cm 3 /r [2.2 in 3 /r] [409] 46 768 45 3 [00] [46] 5 205 [107] 12 8 [170] 1 [233] 26 1 [295] 33 175 [352] 40 166 [462] 52 0 [42] 5 3 [106] 12 406 [1] 399 [234] 26 3 34 377 [360] 364 [485] 336 [36] 4 626 [99] 11 8 [164] 0 26 600 [292] 33 588 [356] 40 575 [484] 5 [726] 82 468 [408] 46 1 [423] 48 350 [421] 48 562 [537] 737 [529] 60 939 [1800] [512] 58 [544] 321 [5] 62 533 [718] 81 2 [52] 6 608 [0] 16 603 [229] 26 5 [317] 36 590 [405] 46 580 [494] 56 568 [670] 76 544 [1018] 115 8 [40] 5 759 [129] 15 754 [218] 25 746 [307] 35 739 [396] 45 730 [484] 7 [660] 75 4 [1011] 1 624 [117] 13 904 [206] 23 6 [293] 33 888 [3] 43 878 [1] 53 867 [648] 73 843 [998] 113 770 [103] 12 1052 [1] 21 1045 [0] 32 1036 [3] 42 1026 [546] 62 1002 [724] 82 0 [800] [1200] [1600] [2400] 165 [12] 45,4 [] 53,0 49 cm 3 /r [3.0 in 3 /r] [581] 66 7 [571] 65 707 [560] 63 8 [457] 52 10 [00] [68] 8 8 [156] 18 2 [242] 27 137 [327] 37 130 125 [493] 56 118 [644] 73 98 [66] 7 302 [154] 17 2 [242] 27 291 [330] 37 4 275 [505] 57 265 [677] 76 244 [59] 7 458 [7] 17 452 [236] 27 445 [324] 37 438 429 [500] 56 420 [675] 76 395 [1018] 115 330 [571] 65 [592] 67 256 [588] 66 408 [756] 85 531 [749] 85 679 [736] 829 [635] 72 988 [1800] [711] 80 82 [7] 86 231 [762] 86 382 113 178 [75] 8 458 22 454 [311] 35 449 [429] 48 443 [0] 62 436 [668] 75 431 [903] 102 4 [13] 1 363 [62] 7 572 [180] 20 568 [298] 34 563 7 [535] 60 0 [651] 74 542 [888] 100 525 [1354] 153 4 [45] 5 687 [164] 681 32 675 45 670 [518] 59 664 [636] 72 6 [874] 99 637 [1342] 152 584 16 795 [265] 30 790 [384] 43 7 [503] 57 776 [621] 70 767 [857] 749 [1329] 150 4 [131] 15 853 [252] 848 [370] 42 842 5 [607] 8 [843] 95 810 [13] 9 748 [116] 13 965 [235] 27 959 [353] 40 952 [0] 53 945 [707] 80 926 [944] 107 901 [800] [1200] [1600] [2400] 165 [12] 45,4 [] 53,0 [15] 56,8 [17] 64,4 66 cm 3 /r [4.0 in 3 /r] [786] 423 [7] 87 535 [7] 85 648 [738] 760 [724] 82 821 [5] 67 936 [00] [102] 12 111 [218] 25 107 [334] 38 103 [452] 51 100 [566] 64 94 [680] 77 101 72 [95] 11 226 [213] 24 223 [331] 37 2 [448] 51 212 [565] 64 206 77 200 [9] 103 184 [] 10 344 [206] 23 340 [324] 37 334 [442] 50 3 [5] 63 322 [678] 77 315 [908] 103 300 [1368] 1 254 [790] 81 [799] 90 2 [795] 90 308 [1021] 115 404 [1006] 1 5 [990] 112 627 737 [963] 7 [825] 93 915 [1800] [993] 112 116 173 [1024] 116 290 [1357] 153 136 [93] 11 374 [237] 27 370 [380] 43 366 [526] 59 3 [671] 76 356 92 350 [5] 334 [1649] 186 291 [77] 9 468 [221] 25 464 [365] 459 [510] 58 454 [654] 74 448 [796] 90 4 [1081] 122 425 [1636] 185 379 [56] 6 5 [201] 23 7 [345] 39 2 [490] 546 [635] 72 539 [779] 88 532 [1064] 120 517 [1627] 184 468 [39] 4 6 [181] 20 650 [326] 37 644 [0] 53 639 [7] 70 632 [758] 86 624 [1046] 118 606 [10] 182 5 [170] 6 [315] 36 2 [462] 52 686 [606] 68 680 [751] 85 672 [1040] 117 653 [1604] 181 596 [127] 4 [272] 31 829 [5] 824 [9] 63 816 96 799 [1136] 1 776 [800] [1200] [1600] [2400] 165 [12] 45,4 [] 53,0 [15] 56,8 [18] 68,1 80 cm 3 /r [4.9 in 3 /r] [9] 108 343 [937] 106 434 [923] 104 525 [902] 102 7 [5] 101 662 [703] 79 808 [00] [115] 13 91 [258] 29 45 86 [539] 82 [675] 76 78 [809] 91 74 121 62 [1] 13 185 [259] 29 182 [404] 46 178 [548] 62 174 [0] 78 1 94 164 [3] 125 150 [106] 12 1 [251] 277 [395] 45 273 [539] 268 77 263 [825] 93 258 125 243 [1651] 187 201 [940] 106 68 [967] 158 [966] 251 [1235] 0 325 [1220] 138 6 [1207] 136 506 [11] 134 596 [1181] 133 642 [992] 112 788 [1800] [11] 135 53 [1238] 0 2 0 235 [1633] 184 108 [] 3 911 [15] 2 1062 [29] 3 800 [] 3 857 Torque [lb-in] Nm } Speed RPM [82] 9 1032 Motors run with high efficiency in all areas designated with a number for torque and speed, however for best motor life select a motor to run with a torque and speed range shown in the light blue area. Performance data is typical at 120 SUS. Actual data may vary slightly from unit to unit in production out out
7 Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed, however for best motor life select a motor to run with a torque and speed range shown in the light blue area. [121] 295 [303] 34 293 [485] 290 [668] 75 5 [850] 96 0 [1032] 117 275 [1391] 157 2 [20] 235 217 [107] 12 370 [291] 33 367 [3] 53 363 [654] 73 359 [8] 95 354 115 348 [1380] 156 334 [2074] 234 8 [81] 9 444 [264] 30 4 [448] 51 437 [632] 71 432 [815] 92 427 [996] 113 421 [1359] 154 406 [2066] 233 358 [239] 27 515 [420] 511 [603] 68 506 [784] 500 [968] 494 [1332] 150 9 [2043] 231 42 [222] 25 1 [405] 46 5 [587] 66 543 [7] 87 538 [952] 108 532 [13] 9 5 [2032] 230 464 [1] 662 [353] 40 657 [534] 60 653 [720] 81 6 [1085] 123 633 [] 163 2 [800] [1200] [1600] [2400] 165 [12] 45,4 [] 53,0 [15] 56,8 [18] 68,1 102 cm 3 /r [6.2 in 3 /r] [1211] 137 268 [1201] 136 342 [1177] 133 5 [1150] 130 487 [1135] 1 524 [902] 102 640 [00] [151] 17 72 [3] 37 70 [508] 57 67 [688] 78 64 [865] 98 [1038] 117 56 [13] 154 44 [157] 18 6 [339] 38 4 [520] 59 1 [703] 79 137 [882] 100 133 [1063] 120 1 [16] 160 1 [3] 16 221 [326] 37 2 [508] 57 212 [1] 78 207 [873] 99 202 [1054] 1 7 [12] 160 1 [20] 235 2 [1202] 136 50 [12] 0 122 [1234] 139 0 [15] 177 252 [] 176 325 [1527] 173 396 [1513] 171 4 [1501] 170 504 [1267] 3 623 [1800] [1508] 170 36 [1587] 179 106 [1587] 179 173 [2065] 233 77 [165] 229 [403] 46 227 [639] 72 224 [875] 99 221 [9] 125 218 [13] 152 2 [1791] 202 204 [2634] 298 163 16 7 [378] 43 4 [8] 70 1 278 [1] 123 275 [1323] 9 271 [1778] 201 2 [2608] 295 2 [1] 13 344 [352] 40 3 [5] 67 338 [826] 93 335 [1062] 120 332 [12] 7 3 [17] 7 3 [2579] 291 274 [320] 36 398 63 395 [791] 393 116 3 [12] 2 385 [1715] 4 375 [2566] 290 3 [301] 34 427 [539] 424 [775] 88 421 [1013] 1 7 [5] 1 3 [14] 1 403 [23] 8 356 [423] 48 566 [659] 74 562 101 8 [1360] 154 549 [1784] 202 533 [800] [1200] [1600] [2400] 165 [12] 45,4 [] 53,0 [15] 56,8 [20] 75,7 131 cm 3 /r [8.0 in 3 /r] [15] 177 209 [] 176 266 [1526] 172 323 [93] 1 380 [76] 167 408 [1129] 1 4 [00] [1] 13 [363] 54 [2] 52 [848] 96 50 [1077] 122 [1298] 7 44 [14] 1 33 [34] 2 29 [185] 21 113 [421] 48 111 [660] 75 101 106 [1126] 127 103 [1356] 153 100 [1798] 203 90 [179] 20 172 [7] 1 [656] 74 166 101 164 [1123] 127 1 [1353] 153 157 [1803] 204 7 [2639] 298 [1505] 170 39 [1581] 179 95 [15] 179 152 [2003] 226 8 [92] 225 2 [48] 220 313 [22] 217 370 [06] 215 398 [1572] 178 543 [1800] [2005] 227 84 [2015] 2 1 [2585] 292 56 [208] 23 0 [495] 56 188 [784] 185 [1068] 121 182 [1351] 153 178 [1631] 184 175 [2154] 243 166 [3012] 340 136 [178] 20 238 [467] 53 235 [7] 85 232 [1038] 117 229 [1322] 9 225 [1603] 181 222 [2133] 2 213 [29] 338 176 [3] 16 6 431] 49 3 [7] 81 0 [1005] 1 277 [1290] 6 273 [15] 177 268 [2104] 238 259 [2965] 335 224 [392] 44 330 [680] 77 327 [966] 323 [1252] 1 3 [1530] 171 3 [20] 233 306 [2935] 332 267 [368] 42 354 [659] 74 351 [946] 107 3 [1230] 139 344 [1510] 171 340 [2034] 230 330 [29] 330 9 [516] 58 468 [796] 90 465 [1084] 122 460 [1645] 186 450 [24] 242 435 [800] [1200] [1600] [2300] 159 [12] 45,4 [] 53,0 [15] 56,8 [20] 75,7 [00] 215 171 [1879] 212 218 [1845] 208 264 [1803] 204 311 [17] 202 335 [1368] 1 4 [00] [229] 26 46 [507] 57 45 [786] 43 [1052] 1 [1315] 9 39 [1566] 177 36 [2038] 230 27 [245] 94 [532] 60 92 [818] 92 90 [9] 87 [1373] 1 85 [1638] 185 81 [29] 243 72 [231] 26 3 [516] 58 0 [802] 91 137 [1085] 123 134 [1366] 154 132 [1640] 185 1 [2159] 244 1 [1813] 205 32 [18] 2 77 [04] 215 [23] 2 158 [2368] 268 205 [2332] 263 252 [2298] 260 298 [2274] 257 322 [12] 216 444 [1800] [2229] 252 20 [2385] 2 66 [2396] 271 113 [253] 29 154 [0] 152 [9] 150 [1307] 8 8 [1652] 187 5 [87] 224 2 [2579] 291 133 [3344] 378 [217] 25 3 [5] 64 1 [923] 104 1 [1267] 3 187 [11] 182 184 [51] 220 181 [2566] 290 172 [3320] 375 4 [184] 21 231 [539] 229 101 227 [1239] 0 224 [1586] 179 221 [25] 217 217 [2526] 5 210 [30] 371 180 [485] 268 [8] 95 265 [11] 135 263 [1536] 174 259 [1880] 212 2 [27] 0 2 [3242] 366 218 [4] 52 7 [816] 92 5 [1167] 132 1 [1512] 171 278 [1851] 209 274 [24] 277 265 [3227] 365 237 [648] 73 380 113 377 [1345] 152 374 [2013] 227 365 [2527] 6 334 [800] [1200] [1600] [2100] 5 [12] 45,4 [] 53,0 [15] 56,8 [20] 75,7 [2298] 260 138 [2274] 257 177 [2239] 253 2 [23] 248 252 [2170] 245 270 [1688] 1 370 [00] [207] 23 37 [566] 64 36 [921] 104 34 [1256] 2 33 [1577] 178 31 [18] 213 [2407] 272 17 [359] 29 76 [8] 70 74 [967] 72 [1315] 9 70 [1654] 187 68 [77] 223 64 [25] 292 [274] 31 115 71 113 [7] 111 [1322] 9 [1665] 188 106 [95] 225 103 [25] 293 95 [3340] 377 74 [2179] 246 24 [29] 259 [2308] 2 100 317 127 [2784] 315 165 [2750] 311 202 [2701] 305 240 [2679] 303 259 [29] 259 343 [1750] 121 [25] 9 11 [2794] 316 51 [16] 318 [3262] 3 35 [1] 270 [111] 13 9 [293] 33 3 [226] 26 570 [229] 26 2 [] 6 518 [37] 4 5 [102] 12 401 [98] 11 430 [101] 11 333 [88] 10 357 [2967] 335 [3015] 3 88 157 cm 3 /r [9.6 in 3 /r] 5 cm 3 /r [11.9 in 3 /r] Torque [lb-in] Nm } Speed RPM [4] 52 7 Performance data is typical at 120 SUS. Actual data may vary slightly from unit to unit in production 1.Booklet.Booklet
out Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed, however for best motor life select a motor to run with a torque and speed range shown in the light blue area. 244 cm 3 /r [.9 in 3 /r] [800] [1200] [00] [1600] [1650] 1 [00] 131 306 cm 3 /r [18.7 in 3 /r] [800] [1200] [1300] 90 [1500] 103 [1800] [12] 45,4 [] 53,0 [15] 56,8 [311] 35 30 [3] [3] 39 92 [317] 36 123 [278] 31 153 [229] 26 185 [168] 215 [132] 15 231 [744] 84 29 [801] 90 59 [792] 91 [11] 134 [1238] 0 58 [1235] 0 [1592] 180 26 [16] 1 56 [1665] 188 87 [81] 224 24 [20] 236 54 [2098] 237 85 [2352] 266 22 [2491] 1 52 [2516] 4 [762] [1202] [1634] [2062] [26] 86 121 136 120 185 118 233 116 0 1 [721] [1166] [1600] [2029] [2450] 81 152 132 150 181 9 229 6 277 4 [673] [11] [] [] [2399] 76 1 126 181 176 179 224 177 271 174 [1059] [94] [27] [2348] 2 120 211 1 209 218 207 265 204 [581] [1025] [63] [14] [2315] 66 229 116 227 165 224 2 222 262 2 [21] 304 18 [51] 322 49 [92] 327 80 [56] 323 111 [08] 317 1 [2770] 313 171 [27] 308 201 [24] 304 216 [2963] 335 [3205] 362 44 [3239] 366 75 [3226] 364 105 [3178] 359 135 [3130] 354 165 [3081] 348 5 [3043] 344 211 [3039] 343 11 [3292] 372 42 [3320] 375 73 [3317] 375 103 [3275] 370 133 [32] 365 163 [3171] 358 4 [34] 3 208 [37] 8 34 [3771] 426 63 [3779] 427 90 [3746] 423 1 [39] 8 8 [3649] 2 178 [3621] 409 3 [12] 45,4 [] 53,0 [15] 56,8 [332] 38 24 45 48 [402] 45 73 [3] 43 98 [338] 38 122 [7] 32 7 [217] 25 172 [1] 1 [913] 103 23 [7] [9] 73 [84] 168 22 [1543] 174 [1533] 173 72 [2029] 229 21 [2092] 236 46 [2079] 235 71 [2532] 6 20 [2599] 294 45 [2581] 292 71 [21] 336 [3072] 3 44 [3046] 344 70 [948] [1502] [20] [2537] [3006] 107 170 96 231 96 7 96 340 95 [49] [86] [21] [2939] 101 122 164 121 224 121 279 120 332 120 [842] [1391] [17] [2382] [68] 95 6 157 6 217 6 270 5 324 5 [773] [1324] [1846] [2312] [2785] 87 171 150 170 209 1 2 170 315 1 [729] [1816] [2271] [2746] 82 1 5 182 205 182 257 181 310 177 [39] 3 18 [3311] 374 43 [3290] 372 [3249] 367 94 [31] 360 1 [3112] 352 4 [30] 342 1 [2988] 338 171 [3533] 399 [3766] 425 40 [3750] 424 66 [3716] 420 91 [36] 2 116 [3580] 404 0 [3498] 395 165 [3460] 391 151 [4329] 4 30 [4390] 496 58 [43] 493 82 [4296] 485 106 [4221] 7 129 [52] 4 152 [16] 465 164 [20] 75,7 [377] 43 306 [818] [12] [1686] 92 303 2 301 0 298 [2104] 238 295 [27] 0 292 [38] 321 4 [2929] 331 2 [20] 75,7 53 244 [1020] [1549] [2013] 115 243 175 243 227 243 [2467] 279 242 [2710] 306 2 [3185] 360 237 370 cm 3 /r [22.6 in 3 /r] [800] [1200] [1300] 90 [1500] 103 [729] 82 1 Torque [lb-in] } Nm Speed RPM [12] 45,4 [] 53,0 [15] 56,8 [1166] [15] [2464] [3043] 54 132 207 18 278 17 344 16 [1226] [15] [2540] [3] [3639] 62 40 139 39 2 39 7 38 353 37 1 35 [544] 60 [504] 57 81 [442] 50 101 [359] 122 [273] 31 2 [223] 25 152 [1218] 138 60 [1177] 133 80 [11] 126 101 [1031] 116 121 [946] 107 1 [3] 101 151 [1879] 212 59 [16] 207 80 [1772] 200 100 1 121 [1605] 181 0 [] 176 150 [2531] 6 59 [2484] 1 79 [24] 273 99 [2330] 263 120 [2240] 253 0 [2188] 2 150 [3108] 351 58 [3066] 346 79 [2986] 337 99 [2916] 329 1 [30] 320 139 [2777] 3 150 [36] 0 56 [3578] 404 77 [3503] 396 [3423] 387 117 [33] 376 137 [3272] 370 8 [32] 440 33 [3886] 439 54 [3853] 435 75 [3782] 427 94 [30] 7 115 [3600] 407 135 [30] 401 5 [4386] 496 29 [4406] 498 49 [4380] 495 [4317] 488 [4226] 7 108 [34] 467 1 [4085] 462 138 [20] 75,7 [5] 64 202 [1231] 139 201 [18] 210 200 [2458] 278 200 [2968] 335 7 [3238] 366 5 Performance data is typical at 120 SUS. Actual data may vary slightly from unit to unit in production 8 out
1.Booklet Dimensions 2 Bolt Flange 82,/82,42 [3.250/3.245] Pilot Dia. 131,4 [5.17] Shaft Dim. See Page 12-13 Geroler Width X Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW Eaton 106,35 [4.187],4 [1.63] (2),3 [3.] (2) 13,62/13,46 [.540/.530] Dia. Thru (2) Holes 96,8 [3.81] Groove Provided for 82,6 [3.25] I.D. x 2,62 [.103] Cross Section O-ring ( Dash No. 152) 4 Bolt Flange 45 44,45/44,32 [1.750/1.745] Pilot Dia. 15,2 [.60] 2,8 [.11] 87,9 [3.46] Y B Port Port Dim. See Page A Port 3/8-16 UNC (15,2 [.60] Bolt Thread Engagement ) Holes (4) Equally Spaced on 82,6 [3.25] Dia. Bolt Circle or M10 x 1,5 (15,2 [.60] Bolt Thread Engagement ) Holes (4) Equally Spaced on 82,6 [3.25] Dia. Bolt Circle Standard Motor End Cap End Cap with Case Drain Port See Page 15 X Y Displ. cm 3 /r [in 3 /r] Width mm [in.] Length mm [in.] 36 [ 2.2] 6,6 [.26] 132,2 [5.21] 49 [ 3.0] 9,1 [.36] 134,6 [5.30] 66 [ 4.0] 12,2 [.48] 137,7 [5.42] 80 [ 4.9],7 [.58] 0,3 [5.53] 102 [ 6.2] 18,5 [.73] 4,3 [5.68] 131 [ 8.0] 24,1 [.95] 9,6 [5.] 157 [ 9.6] 29,0 [1.] 154,5 [6.09] 5 [11.9] 35,6 [1.40] 1,3 [6.35] 244 [.9] 44,7 [1.76] 170,3 [6.71] 306 [18.7] 56,1 [2.21] 181,6 [7.16] 370 [22.6] 72,1 [2.84] 7,9 [7.79].Booklet 9
out Product Numbers 6-xxxx Product Numbers Add three digit prefix 6-to four digit number from chart for complete product numberexample 6-1204. Orders will not be accepted without three digit prefix. Displ. cm 3 /r [in 3 /r] Product Number 6-xxxx Shaft Ports 36 [2.2] 49 [3.0] 66 [4.0] 80 [4.9] 102 [6.2] 131 [8.0] 157 [9.6] 5 [11.9] 244 [.9] 306 [18.7] 370 [22.6] 2 Bolt Flange 4 Bolt Flange 1 in. Straight w/woodruff Key 1 in. SAE 6B Splined 1 in. Straight w/.31 Dia. Crosshole 1 in. Straight w/.40 Dia. Crosshole 1 in. Straight w/woodruff Key 1 in. SAE 6B Splined 1 in. Straight w/.31 Dia. Crosshole 1 in. Straight w/.40 Dia. Crosshole 7/8- O-ring 1/2 NPTF Manifold* 7/8- O-ring 1/2 NPTF Manifold* 7/8- O-ring 1/2 NPTF Manifold* 7/8- O-ring 1/2 NPTF Manifold* 7/8- O-ring 1/2 NPTF Manifold* 7/8- O-ring 1/2 NPTF Manifold* 7/8- O-ring 1/2 NPTF Manifold* 7/8- O-ring 1/2 NPTF Manifold* 6-10 -1042-1043 -1044-1045 -1046-10 -1048-1049 -1050 6-1031 -1032-1033 -1034-1035 -1036-1037 -1038-1039 -1040 6-1051 -1052-1053 -1054-10 -1056-1057 -1058-1059 -1060 6-1 -2-3 -4-5 -6-7 -8-9 -1 6-1 -2-3 -4-5 -6-10 -8-9 -0 6-1111 -1112-1113 -11-1115 -1116-1117 -1118-11 -1120 6-1121 -1122-1123 -1-1125 -1126-1127 6-11 -1129-1130 -1131-1132 -1133-1134 6-1135 -1136-1137 -1138-1139 -10-11 6-12 -13-14 -15-16 -17-18 6- -1150-1151 -1152-1153 -1154-11 6-1156 -1157-1158 -1159-1160 -11-1162 6-1011 -1012-1013 -10-1015 -1016-1017 -1018-10 -1020 6-1001 -1002-1003 -1004-1005 -1006-1007 -1008-1009 -1010 6-1021 -1022-1023 -1024-1025 -1026-1027 -10-1029 -1030 6-1071 -1072-1073 -1074-1075 -1076-1077 -1078-1079 -1080 6-10 -1062-1063 -1064-1065 -1066-1067 -1068-10 -1070 6-1081 -1082-10 -1084-1085 -1086-1087 -1088-10 -0 6-1163 -1164-1165 -1166-1167 -1168-11 6-1170 -1171-1172 -1173-1174 -1175-1176 6-1177 -1178-1179 -1180-1181 -1182-11 6-1184 -1185-1186 -1187-1188 -11-10 6-11 -12-13 -14-15 -16-17 6-18 -19-1200 -1201-1202 -1203-1204 * Manifold product numbers shown are 5/16-18 port face mounting threads (for M8 x 1,5 port face mounting threads see note below). 6-1204 For motors with a configuration Not Shown in the chart above: Use the model code number system on page to specify the product in detail. 10 out
1.Booklet Shaft Side Load Capacity The hydrodynamic bearing has infinite life when shaft load ratings are not exceeded. Hence, the shaft side load capacity is more than adequate to handle most externally applied loads (such as belts, chains, etc.), providing the motor to shaft size is applied within its torque rating. Allowable side load chart, shaft load location drawing and load curves (below) are based on the side / radial loads being applied to shaft at locations A, B, and C, to determine the shaft side load capacity at locations other than those shown use the formula (shown below). For more information about shaft side loads on Char-Lynn motors contact your Eaton representative. Sideload P kg = Sideload P [lb] = 900 N 900 N ( ( 16800 L + 96,3 60 L + [3.79] ) ) for 200-900 RPM for 200-900 RPM Where N = Shaft Speed (RPM) L = Distance from RPM Allowable Shaft Side Load Kg [lb] A B C 900 154 [ 339] 136 [ 300] 118 [ 2] 625 205 [ 452] 181 [ 400] 158 [ 348] 500 256 [ 565] 227 [ 500] 7 [ 435] 400 307 [ 678] 272 [ 600] 237 [ 522] 300 0 [ 904] 363 [ 800] 316 [ 6] 200 718 [1582] 635 [00] 2 [1216] P L C B A 45,2 [1.78] 26,9 [1.06] 12,7 [.50] kg 800 [lb] 718 [1582] 635 [00] 2 [1216] Shaft Side Load kg [lb] 700 600 500 400 300 [1600] [00] [1200] [ 800] [ 600] A B C 200 [ 400] 100 [ 200] 0 0 0 0 Shaft Speed (RPM) 100 200 300 400 500 600 700 800 900.Booklet 11
in Dimensions Shafts Shaft Size /Motor Torque Combination Limit Guide Shaft Option 1 inch Dia. Tapered with Woodruff Key and Nut SAE 6B Splined 25mm w/keyway and 1 inch Dia. Straight w/keyway 1 inch Dia. Straight with.315 Dia. Crosshole 1 inch Dia. Straight with.406 Dia. Crosshole 7/8 inch SAE B 13T Splined Torque Nm 100 200 300 400 [lb-in] [2000] [3000] [4000] 46,0/44,5 [1.81/1.75],1/18,0 [.75/.71] 6,6/4,6 [.26/.18] 25,40/25,15 [1.000/.990] Dia. Key x 6,375/6,350 [.2510/.2500] Wide 46,0/44,5 [1.81/1.75] 24,5 [1.00] Min. Full Spline Depth 6,9/4,8 [.27/.],30/27, [1.1/1.098] 25,40/25,37 [1.000/.999] Dia. 1/4-20 UNC-2B x,2 [.56] Min. Deep 25,35/25,30 [.998/.996] Dia. 1/4-20 UNC-2B x,2 [.56] Min. Deep 1 in. Dia. Straight with Woodruff Key SAE 6B Splined Shaft 51,6/50,0 [2.03/1.] 11,7/10,7 [.46/.42] 6,6/4,6 [.26/.18] 46,0/44,5 [1.81/1.75] 16,3/15,2 [.64/.60] 6,6/4,6 [.26/.18] 25,40/25,37 [1.000/.999] Dia. 1 in. Dia. Straight Shaft with.315 Dia. Crosshole 8,08/7,92 [.318/.312] Dia. Thru 25,40/25,37 [1.000/.999] Dia. 1/4-20 UNC-2B x,2 [.56] Min. Deep 1 in. Dia. Straight Shaft with.406 Dia. Crosshole 10,44/10, [.1/.401] Dia. Thru 12 in
1.Booklet Dimensions Shafts Reduced Length Tapered Shaft Option 1 in. Dia. Tapered (Reduced Length) with Woodruff Key and Nut 25,40/25,15 x 6,38/6,35 [1.000/.990 x.251/.250] Woodruff Key 3/4-16 UNF-2A Slotted Hex. Nut 16,0 [.63] Thick,12 [1.107] Across Flats 203 Nm [150 lb-ft] Torque Plus Torque Required to Align Slotted Nut to Shaft Cross Hole 25,43/25,37 [1.001/.999],8/60,2 [2.43/2.37],05/18,79 x 4,788/4,762 [.750/.740 x.1885/.1875] Woodruff Key 3/4-16 UNF-2A Slotted Hex. Nut 16,0 [.63] Thick,12 [1.107] Across Flats 203 Nm [150 lb-ft] Torque Plus Torque Required to Align Slotted Nut to Shaft Cross Hole 2,16/1,90 [.085/.075] 37,1 [1.46] Coupling Width 4,07/3,81 [.160/.150] Dia. Thru 8,4/7,1 [.33/.] 34,93 [1.375],7/54,1 [2./2.13] 16,3/15,7 [.64/.62] 125,00±0,17 mm Taper Per Meter [1.500±.002 inch Taper Per Foot] Tapered Shaft End Per SAE J501 Except as Specified 50,6/49/,0 [1.99/1.93] 27,99/26 [1.102/1.0] 31,44/30,44 [1.220/1.216] 2 [1.08] Coupling Width 11,9/10,6 [./.42] 8 x 8 x 30mm Straight Key 7,4/5,4 [.29/.21] 3,31/2,93 [.130/.115] 25,43/25,37 [1.001/.999] 1 in. Dia. Tapered Shaft with Woodruff Key and Nut 4,06/3,81 [.160/.150] Dia. Thru 125,00±0,17mm Taper Per Meter [1.500±.002 inch Taper Per Foot] Tapered Shaft End Per SAE J501 Except as Specified 25,00/24,.984/.9 Dia. M8 x 1,25-6H x 16,0 [.63] Deep 25mm Dia. Straight Shaft with 8mm Keyway 38,6/37,0 [1.52/1.46] 5,6/3,6 [.22/.] 21,79/21,66 [.858/.853] Major Dia. 7/8 in. Dia. SAE B Shaft 13 T Splined.Booklet 13
in Dimensions Ports 2 Bolt Flange 44,7 [1.76] 42,7 [1.64] 7/8- UNF O-ring Ports (2) Side Ports 45,7 [1.80] 4 Bolt Flange 22,9 [.90] Use of Teflon Tape Sealant/Lubricant (with 1/2 NPTF Port Connectors only). When using fittings with Teflon tape, be careful when taping and tightening. Over tightening or Wrap improperly taped fittings can cause damage to housing or leakage. Use the following procedures: Wrap approx. 1 1/2 Turns of 13 mm [1/2 in.] wide Teflon Tape around fitting threads start tape 2 threads up from end of fitting. Tighten threads to a Maximum of 34 Nm [25 lb-ft]. Do Not Tighten Further If fittings leak when tightened to maximum torque, either retape, reseal, or replace fittings. 42,7 [1.64] 1/2- NPTF (2) 22,9 [.90] 45,7 [1.80] Manifold Ports,4 [1.12] 42,7 [1.64] 22,9 [.90] 31,6 [1.25] 45,7 [1.80] 42,7 [1.64] G 1/2 (BSP) (2) 45,7 [1.80],2 [.56] 63,5 [2.50] 5/16-18 UNC (12,7 [.50] Screw Thread Engagement) (4) or M8 x 1,5 (12,7 [.50] Screw Thread Engagement) (4) 22,9 [.90] in
1.Booklet Case Pressure and Case Drain Parallel or Series Connection Hydraulic lines bringing pressurized fluid from the pump to the motor and return flow from the motor back to tank can be flexible or ridged. One power source and one pump can be sized to supply one motor or many motors. Furthermore, one pump and multiple motors can be connected in series or in parallel (see each type of connection shown below). When connecting the pump to the motors in series excess internal case pressure is created in the motor, this excess pressure in each motor must be ported back to tank. However, when making a parallel connection from the pump to the motors no excess case pressure will be added. Hence, using the case drain ports are not necessary. Meanwhile, take a look at the application and see if this optional case drain port can be connected to your advantage, wether it be a single motor to pump connection, multiple motors connected to pump in parallel, as well as multiple motors connected to pump in series......case Drain Advantage In addition to providing lower case pressures for motors connected in series, there are advantages for adding an external case drain line to motors with normal case pressures as well. These advantages are: Contamination Control flushing the motor case. Cooler Systems exiting oil draws motor heat away. Extend Motor Seal Life maintain low case pressure with a preset restriction installed in the case drain line. Motors ordered with case drain port will be shipped with steel hex socket plug installed in that end cap drain port. Case Drain Optional Parallel Connection Series Connection with Case Drain Port G 1/4 (BSP) or 7/16-20 O-ring Eaton.Booklet 15
in Case Pressure and Case Drain Char-Lynn motors are durable and have long life as long as the recommended case pressure is not exceeded. Allowable case pressure is highest at low shaft speeds. Consequently, motor life will be shortened if case pressure exceeds these ratings (acceptability may vary with application). Finally, determine if an external case drain is required (see case pressure seal limition chart below chart based on case pressure and shaft speed). In conclusion, if a case drain line is needed, connect drain line to assure that the motor will always remain full of fluid. However, a pressure restriction should be added to the case drain line, during which a motor case pressure of 3,5 Bar [50 PSI] is maintained. Thrust Load Axial Loads 454 kg [1000 lb] 103 [1500] Case Pressure Bar [PSI] 150 100 50 [2000] [1500] [ 500] Case Drain Optional Case Drain Required Case Drain Optional P 1 P 2 Pc 0 0 0 0 100 200 300 400 500 600 700 800 900 1000 Speed RPM Case Pressure Seal Limitation Speed Sensor Eaton has developed a speed sensor specifically designed for LSHT motors. The design is rugged and fully protected against accidental reverse polarity or short circuit hook up. A built in pull up resistor simplifies installation with control systems. This sensor is fully compatible with mobile vehicle electrical systems and gives a reliable digital on/off signal over a wide speed range and temperature range. Connection standard 3 prong Weatherpack connector with 18 AWG (american wire gage) cables: Position A (red) = power supply Position B (white) = signal output Position C (black) = common RPM A B C 16 in
1.Booklet Dimensions Options 15,2 [.60] 2,8 [.11] 131,4 [5.17] 82,/82,42 [3.250/3.245] Pilot Dia. 106,35 [4.187] Dia. Bolt Circle Base Block Kits 4 Bolt Magneto 13,62/13,46 [.540/.530] Dia. Thru (2) Holes 96,8 [3.81] No.123-1008 7/8- O-ring Port (2) No.123-1007 1/2 NPTF Port (2) 15,2 [.60] 82,6 [3.25],05 [.75] 13,2 [.52] 121,9 [4.80] Motor 50,8 [2.00] 9,4 [.37] 57,2 [2.25] 76,2 [3.00] 10,2 [.40] Dia. Holes (4) 101,6 [4.00].Booklet 17
in Fluid Recommendations Introduction The ability of Eaton hydraulic components to provide the desired performance and life expectancy depends largely on the fluid used. The purpose of this section is to provide readers with the knowledge required to select the appropriate fluids for use in systems that employ Eaton hydraulic components. One of the most important characteristics to consider when choosing a fluid to be used in a hydraulic system is viscosity. Viscosity choice is always a compromise; the fluid must be thin enough to flow easily but thick enough to seal and maintain a lubricating film between bearing and sealing surfaces. Viscosity requirements, see chart below. Viscosity and Temperature Fluid temperature affects viscosity. In general, as the fluid warms it gets thinner and its viscosity decreases. The opposite is true when fluid cools. When choosing a fluid, it is important to consider the start-up and operating temperatures of the hydraulic system. Generally, the fluid is thick when the hydraulic system is started. With movement, the fluid warms to a point where a cooling system begins to operate. From then on, the fluid is maintained at the temperature for which the hydraulic system was designed. In actual applications this sequence varies; hydraulic systems are used in many environments from very cold to very hot. Cooling systems also vary from very elaborate to very simple, so ambient temperature may affect operating temperature. Equipment manufacturers who use Eaton hydraulic components in their products should anticipate temperature in their designs and make the appropriate fluid recommendations to their customers. Cleanliness Cleanliness of the fluid in a hydraulic system is extremely important. Eaton recommends that the fluid used in its hydraulic components be maintained at ISO Cleanliness Code 18/13 per SAE J1165. This code allows a maximum of 2500 particles per milliliter greater than 5 µm and a maximum of 80 particles per milliliter greater than 15 µm. Cleanliness requirements for specific products are given in the table below. OEM s and distributors who use Eaton hydraulic components in their products should provide for these requirements in their designs. A reputable filter supplier can supply filter information. Fluid Maintenance Maintaining correct fluid viscosity and cleanliness level is essential for all hydraulic systems. Since Eaton hydraulic components are used in a wide variety of applications it is impossible for Eaton to publish a fluid maintenance schedule that would cover every situation. Field testing and monitoring are the only ways to get accurate measurements of system cleanliness. OEM s and distributors who use Eaton hydraulic components should test and establish fluid maintenance schedules for their products. These maintenance schedules should be designed to meet the viscosity and cleanliness requirements laid out in this document. Fluid Selection Premium grade petroleum based hydraulic fluids will provide the best performance in Eaton hydraulic components. These fluids typically contain additives that are beneficial to hydraulic systems. Eaton recommends fluids that contain anti-wear agents, rust inhibitors, anti-foaming agents, and oxidation inhibitors. Premium grade petroleum based hydraulic fluids carry an ISO VG rating. SAE grade crankcase oils may be used in systems that employ Eaton hydraulic components, but it should be noted that these oils may not contain all of the recommended additives. This means using crankcase oils may increase fluid maintenance requirements. Hydraulic fluids that contain V.I. (viscosity index) improvers, sometimes called multi-viscosity oils, may be used in systems that employ Eaton hydraulic components. These V.I. improved fluids are known to shear-down with use. This means that their actual viscosity drops below the rated value. Fluid maintenance must be increased if V.I. improved fluids are used. Automotive automatic transmission fluids contain V.I. improvers. Synthetic fluids may be used in Eaton hydraulic components. A reputable fluid supplier can provide information on synthetic fluids. Review applications that require the use of synthetic fluids with your Eaton representative. Product Line Viscosity Minimum 70 SUS 13 cst Best Range 100-200 SUS 20-43 cst ISO Cleanliness Requirements 18/13 Additional Notes: Fluids too thick to flow in cold weather start-ups will cause pump cavitation and possible damage. Motor cavitation is not a problem during cold start-ups. When choosing a hydraulic fluid, all the components in the system must be considered and the best viscosity range adjusted accordingly. For example, when a medium duty piston pump is combined with a Geroler motor the best viscosity range becomes 100-150 SUS [20-32 cst] and viscosity should never fall below 70 SUS [13 cst]. If the natural color of the fluid has become black it is possible that an overheating problem exists. If the fluid becomes milky a water contamination problem may exist. Take fluid level reading when the system is cold. Contact your Eaton representative if you have specific questions about the fluid requirements of Eaton hydraulic components. 18 in
1.Booklet Model Code for Motors The following 16-digit coding system has been developed to identify all of the configuration options for the Motor. Use this model code to specify a motor with the desired features. All 16-digits of the code must be present when ordering. You may want to photocopy the matrix below to ensure that each number is entered in the correct box. Model Code Spool Valve Motors 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 M R 0 0 0 Position 1 Product Series M... Motor Position 2, 3 R0... Position 4, 5 Displacement cm 3 /r [in 3 /r] 02... 36 [ 2.2] 03... 49 [ 3.0] 04... 66 [ 4.0] 05... 80 [ 4.9] 06... 102 [ 6.2] 08... 131 [ 8.0] 10... 157 [ 9.6] 12... 5 [11.9] 15... 244 [.9]... 306 [18.7] 05... 370 [22.6] Position 6 Flange A... 2 Bolt (Standard) 82,6 [3.25] Pilot Dia. and 13,59 [.535] Dia. Holes 106,2 [4.18] Dia. B.C. B... 4 Bolt (Standard) 44,4 [1.75] Pilot Dia. and 3/8-16 Mouning Holes 82,6 [3.25] Dia. B.C. E... 4 Bolt (Standard) 44,4 [1.75] Pilot Dia. and M10 x 1,5 Holes 82,6 [3.25] Dia. B.C. K... 4 Bolt Magneto 82,6 [3.25] Pilot Dia. and 13,59 [.535] Dia. Holes 106,2 [4.18] Dia. B.C. Position 7, 8 Output Shaft 01... 1 inch Dia. Straight with Woodruff Key and 1/4-20 Threaded hole 02... 1 inch Dia. SAE 6B Splined with 1/4-20 Threaded Hole 07... 1 inch Dia. Straight with 7,9 [.31] Dia. Crosshole 11,2 [.44] from End 08... 1 inch Dia. Straight with 10,2 [.40] Dia. Crosshole 15,7 [.62] from End and 1/4-20 Threaded Hole 16... 7/8 inch Dia. SAE B 13T Splined 18... 1 inch Dia. Tapered with Woodruff Key and Nut 24... 25mm Dia. Straight with 8mm Key adn 8mm x 1,2 Threaded Hole 32... 1 inch Dia. Straight with 10,2 [.40] Dia. Crosshole 15,7 [.62] from End and 1/4-20 Threaded Hole (Plated for Corrosion Protection) 37... 1 inch Dia. Tapered with Woodruff Key and Nut, 9,52 [.375] Reduced Length Position 9 Port Type A... 7/8- O-ring B... 1/2- NPTF C... Manifold (5/16-18 Threads) D... Manifold (M8 x 1,5 Threads) E... G 1/2 (BSP) Position 10 Case Drain 0... No Case Drain 1... 7/16-20 O-ring Port End Cap 2... G 1/4 (BSP) Port End Cap Position 11, 12 Special Features (Hardware) 00... None AC... Viton Shaft Seal AB... Low Speed Valve BZ... Speed Sensor Position 13 Special Features (Assembly) 0... None 1... Reverse Rotation 2... Flange Rotated 90 Position Paint/Special Packaging 0... No Paint A... Painted Low Gloss Black (Standard D... Corrosion Protected Position 15 Eaton Assigned Code when Applicable 0... Assigned Code Position 16 Eaton Assigned Design Code 0... Design Code.Booklet
Eaton Fluid Power Group Hydraulics Business USA 5 Lone Oak Road Eden Prairie, MN 344 USA Tel: 952-937-9800 Fax: 952-294-7722 www.eaton.com/hydraulics Eaton Fluid Power Group Hydraulics Business Europe Route de la Longeraie 7 1 Morges Switzerland Tel: + (0) 21 811 4600 Fax: + (0) 21 811 4601 Eaton Fluid Power Group Hydraulics Business Asia Pacific 11th Floor Hong Kong New World Tower 300 Huaihai Zhong Road Shanghai 200021 China Tel: 86-21-6387-9988 Fax: 86-21-6335-3912 2008 Eaton Corporation All Rights Reserved Printed in USA Document No. C-MOLO-TM009-E Supersedes 11-103 December 2008