POWER WINDOW (RER), RER WIPER ND WSHER FROM POWER SOURCE SSTEM (SEE PGE 8) B6 BOD ECU 5 CC 5 WIPER WIP 9 9 CC UP 5 DOWN R/W ON 0 R/W INT WMTR KSW GND 8 G 8 H 8 J GR R R- B C BCK WINDOW CONTRO SW [CENTER CUSTER SW] GR- G GR- R G - R UP 6 - W DOWN W, B WSHER MOTOR (*) 5 B (*) M (*) B (*) J 6 JUNCTION CONNECTOR - W (*) J 5 JUNCTION CONNECTOR P - R (*) 8 IF (*) RRU 7 IF G G RRD E IF (*) (*) (*) D DIODE (BCK WINDOW) P 7 WINDOW OCK SW [POWER WINDOW MSTER SW] (*) - W 0 7 9 E 6 E (*) (*) B 5 BCK WINDOW OCK SW E WSHER OFF INT ON WSHER 0 C5 RER WIPER ND WSHER SW [COMB. SW] I U UNOCK WRNING SW J 9 JUNCTION CONNECTOR (*) J JUNCTION CONNECTOR IF IE 7 00 RUNNER (EWD7U)
B6 BOD ECU FROM POWER SOURCE SSTEM (SEE PGE 8) 0 POWER 0 ECU- IG 5 MPX- B 7 MPX ECU- B 0 ECU- IG 0 POWER C G IG I C C * : W/ POWER WINDOW * : W/O POWER WINDOW * : W/ DTIME RUNNING IGHT * : W/O DTIME RUNNING IGHT 8 IE IE 6 IE IE BR 6 BR BR 8 BR 5 BS 8 BS 5 BS 6 BS 00 RUNNER (EWD7U) 7
POWER WINDOW (RER), RER WIPER ND WSHER B8 BCK DOOR ECU IG POWE ECU- B MPX WIP- WIP+ MT MT 8 5 - B - GR GR- R 6 RETURN POSITION M FURTHEST POSITION STOP P W R9 RER WIPER MOTOR 5 BS B 9 BR BH 7 00 RUNNER (EWD7U)
B8 BCK DOOR ECU CS OPN MTW GND CSM OPNM BZR BZR 9 0 6 5 BS BS P- B P- G G- R G- R- R G P- B P- G T TIGTE CONTRO SW UP DOWN B BCK WINDOW IMIT SW M B BCK WINDOW MOTOR BR BR P- B 6 IE 5 IE P- B P- G P- G K KEESS BUZZER B 9 B 9 00 RUNNER (EWD7U) 75
POWER WINDOW (RER), RER WIPER ND WSHER SSTEM OUTINE Current always flows through the POWER fuse to TERMIN of the body ECU and TERMIN of the back door ECU. With the ignition SW turned on, the WIPER fuse to TERMIN 9 of the body ECU, the ECU-IG fuse to TERMIN 0 of the body ECU and TERMIN of the back door ECU.. RER POWER WINDOW MNU OPERTION (BCK WINDOW CONTRO SW) When the back window control SW is pushed to the up side (With the ignition SW on), an ON signal is input from TERMIN of the back window control SW to TERMIN () 5 of the body ECU to TERMIN () 7 to TERMIN 8 of the back door ECU. Thus, the back door ECU is activated and the current to TERMIN of the back door ECU flows to TERMIN 6 of the back door ECU to GROUND so that the current to back window motor flows from TERMIN of the back door ECU to TERMIN to TERMIN of the back window motor to TERMIN to TERMIN of the back door ECU to TERMIN 6 to GROUND. This causes the back window motor to rotate toward the up side and the window ascends only while the back window control SW is being pushed. To lower the window, the signal input from TERMIN of the back window control SW to TERMIN () of the body ECU to TERMIN () 7 to TERMIN 8 of the back door ECU. Causes current to the back window motor to flow from TERMIN of the back door ECU to TERMIN to TERMIN of the back window motor to TERMIN to TERMIN of the back door ECU to TERMIN 6 to GROUND, so the current flows in the revers direction to manual up operation and causes the motor to rotate in the opposite direction, thus lowering the window. When the back window lock SW is pushed the lock side, the ground circuit of the back window control SW becomes open. Thus even if the driver operates the Open/Close function of the power window (Rear), the power window (Rear) will not operate because the back door ECU dose not receive the on signal and the back door ECU does not operate.. RER POWER WINDOW MNU OPERTION (TIGTE CONTRO SW) When the tailgate control SW to the up side a signal is input to TERMIN 9 of the back door ECU from TERMIN of the tailgate control SW. This activates the back door ECU regardless of whether the ignition SW is on or off, and the current flows from TERMIN of the back door ECU to TERMIN 6. So the current to the back window motor flows to TERMIN of the back door ECU to TERMIN to TERMIN of the back window motor to TERMIN to TERMIN of the back door ECU to TERMIN 6 to GROUND and causes the back window motor to rotate in the up direction so the back window ascends only while the tailgate control SW is being pushed to lower the window. The on signal of the tailgate control SW (Rotate to down side) is input to TERMIN 0, causing the current to the motor to flow to TERMIN of the back door ECU to TERMIN to TERMIN of the back window motor to TERMIN to TERMIN of the back door ECU to TERMIN 6 to GROUND. This flow is the reverse of manual up, so the motor rotates in the reverse direction and the window is lowered.. WIREESS BCK WINDOW CONTRO When the ignition SW is off, the back window can be opened by pressing the back window open SW of the transmitter for approximately 0.8 seconds. t that time, the keyless buzzer beeps once.. RER WIPER OPERTION With ignition SW turned on and the back door window completely closed (Back window limit SW on), when the rear wiper and washer SW is turned on, the signal is input from TERMIN 0 of the rear wiper and washer SW to TERMIN () 0 of the body ECU to TERMIN 7 to TERMIN 8 of the back door ECU. Thus the back door ECU activates and the current flows from TERMIN of the back door ECU to TERMIN 5 to TERMIN of the rear wiper motor to TERMIN to TERMIN of the back door ECU to TERMIN 6 to GROUND and operates the rear wiper to the upper limit of the wiping area. When the upper limit of the wiping area is reached, the point (Cam plate P point) on the wiper motor is turned on (in the case, W point of cam plate is off), and the signal to reverse the rear wiper motor is input to TERMIN of the back door ECU. The back door ECU stops the rear wiper motor for about 0. seconds and the current flows from TERMIN of the back door ECU to TERMIN of the rear wiper motor to TERMIN to TERMIN 5 of the back door ECU to TERMIN 6 to GROUND. s a result, the rear wiper motor reverses and stops the rear wiper before the retraction position. t that time, the point (Cam plate W point) on the rear wiper motor is turned on (in this case, P point of cam plate is off), and the signal to rotate the motor is input to TERMIN 5 of the back door ECU to TERMIN of the rear wiper motor to TERMIN to TERMIN of the back door ECU to TERMIN 6 to GROUND and the rear wiper SW off, the signal to TERMIN of the back door ECU from W point of cam plate is cancelled and the wiping function is continued when P point is turned on. The rear wiper continues beyond the rear wiper area to the retraction position. t that time, P and W points are turned on, the power window relay stops operating, and the current to the rear wiper is cut off to cam plate rear wiper operation. 5. WSHER OPERTION With the ignition SW turned on and back window closed completely (Back window limit SW on), when the rear wiper and washer SW is turned strongly (Rear washer SW on), current flows from TERMIN 9 of the body ECU to TERMIN to TERMIN (w/o daytime running light), 5 (w/ daytime running light) of the washer motor to TERMIN to TERMIN of the rear wiper and washer SW to TERMIN to GROUND and causes the rear window washer emits a water spray only while the rear washer SW is turned. When the rear wiper SW is off, and the rear wiper SW is then turned in the off direction, washer liquid will also spray. 76 00 RUNNER (EWD7U)
SERVICE HINTS T TIGTE CONTRO SW - : Continuity with tailgate control SW at down side - : Continuity with tailgate control SW at up side C5 RER WIPER ND WSHER SW [COMB. SW] - : Continuity with rear wiper and washer SW at WSHER position 0- : Continuity with rear wiper and washer SW at ON position B8 BCK DOOR ECU -GROUND : pprox. volts with ignition SW at ON position -GROUND : lways approx. volts 6-GROUND : lways continuity -GROUND : pprox. volts with back window at UP operation -GROUND : pprox. volts with back window at DOWN operation 9-GROUND : Continuity with tailgate control SW at UP position 0-GROUND : Continuity with tailgate control SW at DOWN position B BCK WINDOW IMIT SW - : Closed with back power window fully closed R9 RER WIPER MOTOR, 6-5 : Continuity with rear wiper retracted -5 : Continuity with rear wiper at RETURN position : PRTS OCTION Code See Page Code See Page Code See Page B5 0 D 0 R9 B J T B J5 U B6 0 J6 B8 J9 C5 0 K 9 C 0 P7 : RE BOCKS Code See Page Relay Blocks (Relay Block ocation) Engine Room R/B (Engine Compartment eft),,,,,, : JUNCTION BOCK ND WIRE HRNESS CONNECTOR,,, Code See Page Junction Block and Wire Harness (Connector ocation) C G H J C E Cowl Wire and Driver Side J/B (ower Finish Panel) 6 Cowl Wire and Center J/B (Near the Steering Column Tube) : CONNECTOR JOINING WIRE HRNESS ND WIRE HRNESS Code See Page Joining Wire Harness and Wire Harness (Connector ocation) IE IE 8 Cowl Wire and Floor No. Wire (eft Kick Panel) IF 8 Front Door H Wire and Cowl Wire (eft Kick Panel) IG 8 Engine Room Main Wire and Cowl Wire (eft Kick Panel) BR BR BS BS Back Door No. Wire and Floor No. Wire (eft Rear Side of Roof) Back Door No. Wire and Back Door No. Wire (Back Door eft) W 9 B 9 00 RUNNER (EWD7U) 77
POWER WINDOW (RER), RER WIPER ND WSHER : GROUND POINTS Code See Page Ground Points ocation IE 8 Cowl Side Panel H IF 8 Cowl Side Panel RH BH eft Quarter Panel Inner : SPICE POINTS Code See Page Wire Harness with Splice Points Code See Page Wire Harness with Splice Points I B9 Back Door No. Wire 0 Cowl Wire I 78 00 RUNNER (EWD7U)
MEMO 00 RUNNER (EWD7U) 79