Feaures can be Less han, Greaer han or Equal o V CCB 1.2V o 5.5V on A Por and 1.2V o 5.5V on B Por High Speed wih 20 Mb/s Daa Rae for push-pull applicaion High Speed wih 2 Mb/s Daa Rae for open-drain applicaion No Direcion-Conrol Signal Needed Low Bi-o-Bi Skew Non-preferenial Power-up Sequencing ESD proecion exceeds 8KV HBM per JESD22- A114 Inegraed 10 kω Pull-up Resisors Package: UDFN1.2x1.6-8L and MSOP-8L Descripion The PI4ULS5V202 is a 2-bi configurable dual supply bidirecional auo sensing ranslaor ha does no require a direcional conrol pin. The A and B pors are designed o rack wo differen power supply rails, and V CCB respecively. Boh he and V CCB supply rails are configurable from 1.2V o 5.5V. This allows volage logic signals on he side o be ranslaed ino lower, higher or equal value volage logic signals on he V CCB side, and vice-versa. The ranslaor has inegraed 10 kω pull-up resisors on he I/O lines. The inegraed pull-up resisors are used o pull-up he I/O lines o eiher or V CCB. The PI4ULS5V202 is an excellen mach for open-drain applicaions such as he I 2 C communicaion bus. Applicaions I 2 C, SMBus, MDIO Low Volage ASIC Level Translaion Mobile Phones, PDAs, Camera Pin Configuraion VccA A1 A2 GND A1 A2 GND UDFN1.2x1.6-8L V CCB B1 B2 EN VccB B1 B2 EN Pin Descripion Pin No Pin Name Type Descripion 1 Power A-por supply volage.1.2v 5.5 V 2 A1 I/O Inpu/oupu A. Referenced o. 3 A2 I/O Inpu/oupu A. Referenced o 4 GND GND Ground. 5 EN Inpu Oupu enable (acive High). Pull EN low o place all oupus in 3- sae mode. 6 B2 I/O Inpu/oupu B. Referenced o V CCB 7 B1 I/O Inpu/oupu B. Referenced o V CCB 8 V CCB Power B-por supply volage. 1.2 V V CCB 5.5V MSOP-8L 1
Block Diagram Figure 1: Block Diagram Maximum Raings Sorage Temperaure... -65 o C o +150 o C DC Supply Volage por B... -0.3V o +5.5V DC Supply Volage por A... -0.3V o+5.5v Vi(A) referenced DC Inpu / Oupu Volage... -0.3V o +5.5V Vi(B) referenced DC Inpu / Oupu Volage... -0.3V o+5.5v Enable Conrol Pin DC Inpu Volage... -0.3V o+5.5v Shor circui duraion (I/O o GND)... 40mA Noe: Sresses greaer han hose lised under MAXIMUM RATINGS may cause permanen damage o he device. This is a sress raing only and funcional operaion of he device a hese or any oher condiions above hose indicaed in he operaional secions of his specificaion is no implied. Exposure o absolue maximum raing condiions for exended periods may affec reliabiliy. Recommended operaion condiions Symbol Parameer Min Typ Max Uni Posiive DC Supply Volage 1.2-5.5 V V CCB V CCB Posiive DC Supply Volage 1.2-5.5 V V EN Enable Conrol Pin Volage GND - 5.5 V V IO I/O Pin Volage GND - 5.5 V T A Operaing Temperaure Range 40 - +85 C 2
DC Elecrical Characerisics Unless oherwise specified, -40 C T A 85 C, 1.2V Vcc 5.5V Symbol Parameer Tes Condiions Min Typ Max Uni V IHB B por Inpu HIGH Volage - V CCB 0.2 - - V V ILB B por Inpu LOW Volage - - - 0.15 V V IHA A por Inpu HIGH Volage - 0.2 - - V V ILA A por Inpu LOW Volage - - - 0.15 V V IH Conrol Pin Inpu HIGH Volage - 0.2 - - V V IL Conrol Pin Inpu LOW Volage - - - 0.15 V V OHB B por Oupu HIGH Volage B por source curren = -20 µa 2/3 * V CCB - - V V OLB B por Oupu LOW Volage B por sink curren =1 ma - - V OHA A por Oupu HIGH Volage A por source curren= -20 µa 2/3 * V OLA A por Oupu LOW Volage A por sink curren =1 ma - - I QVCB I QVCA I TS V CCB V CCB Supply Curren Supply Curren B Tri sae Oupu Mode B por and A por unconneced, VEN = B por and A por unconneced, VEN = B por and A por unconneced, VEN = GND B por and A por unconneced, VEN = GND 1/3 * V CCB V - - V 1/3 * V - 0.5 5.0 µa - 0.3 5.0 µa - 0.1 1 µa I TS A Tri sae Oupu Mode Supply Curren - 0.1 1 µa I/O Tri sae Oupu Mode I OZ Leakage - 0.1 1.0 µa Curren R PU Pull Up Resisors I/O A and B - 10 - kω Noe: All unis are producion esed a T A = +25 C. Limis over he operaing emperaure range are guaraneed by design. Typical values are for V CCB = +2.8 V, = +1.8 V and T A = +25 C. AC Elecrical characerisics Timing Characerisics Rail o Rail Driving Configuraion (I/O es circuis of Figures 2, 3 and 7, C LOAD = 15 pf, driver oupu impedance 50Ω, R LOAD = 1 MΩ, unless oherwise specified) Symbol Parameer Tes Condiions Min Typ Max Uni = 1.8V, V CCB = 2.8V RB B por Rise Time FB B por Fall Time RA A por Rise Time - - - 25 ns FA A por Fall Time - - - 10 ns PLH A B PLH B A To be coninued. 3
Coninuously. Symbol Parameer Tes Condiions Min Typ Max Uni = 2.8V, V CCB =1.8V RB B por Rise Time - - - 25 ns FB B por Fall Time - - - 10 ns RA A por Rise Time FA A por Fall Time PLH A B PLH B A = 2.5V, V CCB =3.6V RB B por Rise Time FB B por Fall Time - - - 10 ns RA A por Rise Time FA A por Fall Time - - - 10 ns PLH A B PLH B A = 3.6V, V CCB =2.5V RB B por Rise Time FB B por Fall Time - - - 10 ns RA A por Rise Time FA A por Fall Time PLH A B P LH B A To be coninued. 4
Coninuously. Symbol Parameer Tes Condiions Min Typ Max Uni = 1.5V, V CCB = 5.5V RB B por Rise Time FB B por Fall Time RA A por Rise Time - - - 30 ns FA A por Fall Time - - - 10 ns PLH A B PLH B A = 5.5, V CCB =1.5V RB B por Rise Time - - - 30 ns FB B por Fall Time RA A por Rise Time FA A por Fall Time - - - 40 ns PLH A B PLH B A = 1.2V, V CCB = 5.5V RB B por Rise Time FB B por Fall Time - - - 30 ns RA A por Rise Time - - - 30 ns FA A por Fall Time PLH A B PLH B A = 5.5V, V CCB = 1.2V RB B por Rise Time - - - 30 ns FB B por Fall Time RA A por Rise Time FA A por Fall Time - - - 30 ns PLH A B PLH B A 5
Timing Characerisics Open Drain Driving Configuraion (I/O es circuis of Figures 4, 5 and 7, C LOAD = 15 pf, driver oupu impedance 50Ω, R LOAD = 1 MΩ, unless oherwise specified) Symbol Parameer Tes Condiions Min Typ Max Uni 1.2 V CCB 5.5V RB B por Rise Time - - - 450 ns FB B por Fall Time - - - 30 ns RA A por Rise Time - - - 450 ns FA A por Fall Time - - - 30 ns - - - 300 ns PLH A B - - - 300 ns - - - 300 ns PLH B A - - - 300 ns PPSKEW Par o Par Skew - - - 50 ns MDR Maximum Daa Rae - 2 - - Mbps Tes Circuis 6
7
Funcional Descripion The PI4ULS5V202 is a 2-bi configurable dual supply bidirecional auo sensing ranslaor ha does no require a direcional conrol pin. The A and B pors are designed o rack wo differen power supply rails, and V CCB respecively. Boh he and V CCB supply rails are configurable from 1.2 V o 5.5 V. This allows volage logic signals on he side o be ranslaed ino lower, higher or equal value volage logic signals on he V CCB side, and vice-versa. The ranslaor has inegraed 10 kω pull up resisors on he I/O lines. The inegraed pull-up resisors are used o pull up he I/O lines o eiher or V CCB. The PI4ULS5V202 is an excellen mach for open-drain applicaions such as he I 2 C communicaion bus. Applicaion Informaion Level Translaor Archiecure The PI4ULS5V202 auo sense ranslaor provides bidirecional volage level shifing o ransfer daa in muliple supply volage sysems. This device has wo supply volages, and V CCB, which se he logic levels on he inpu and oupu sides of he ranslaor. When used o ransfer daa from A por o B por, inpu signals referenced o he supply are ranslaed o oupu signals wih a logic level mached o V CCB. In a similar manner, ranslaion shifs inpu signals wih a logic level compaible o V CCB o an oupu signal mached o. The PI4ULS5V202 consiss of wo bidirecional channels ha independenly deermine he direcion of he daa flow wihou requiring a direcional pin. The one sho circuis are used o deec he rising or falling inpu signals. In addiion, he one shos decrease he rise and fall ime of he oupu signal for high-o-low and low-o-high ransiions. Each inpu/oupu channel has an inernal 10 kω pull. The magniude of he pull-up resisors can be reduced by connecing exernal resisors in parallel o he inernal 10 kω resisors. Inpu Driver Requiremens The rise ( R ) and fall ( F ) iming parameers of he open drain oupus depend on he magniude of he pull up resisors. In -addiion, he propagaion imes ( PD ), skew ( PSKEW ) and maximum daa rae depend on he impedance of he device ha is conneced o he ranslaor. The iming parameers lised in he daa shee assume ha he oupu impedance of he drivers conneced o he ranslaor is less han 50 kω. Enable Inpu (EN) The PI4ULS5V202 has an Enable pin (EN) ha provides ri sae operaion a he I/O pins. Driving he Enable pin o a low logic level minimizes he power consumpion of he device and drives he I/O V CCB and I/O pins o a high impedance sae. Normal ranslaion operaion occurs when he EN pin is equal o a logic high signal. The EN pin is referenced o he supply and has overvolage oleran proecion. Power Supply Guidelines During normal operaion, supply volage can be greaer han, less han or equal o V CCB. The sequencing of he power supplies will no damage he device during he power up operaion. For opimal performance, 0.01 μf o 0.1μF decoupling capaciors should be used on he and V CCB power supply pins. Ceramic capaciors are a good design choice o filer and bypass any noise signals on he volage lines o he ground plane of he PCB. The noise immuniy will be maximized by placing he capaciors as close as possible o he supply and ground pins, along wih minimizing he PCB connecion races. 8
Mechanical Informaion UDFN1.2x1.6-8L 9
Recommended Land paern for DFN1.6*1.2-8L Noe: All linear dimensions are in millimeers 10
MSOP-8 Ordering Informaion Par No. Package Code Package PI4ULS5V202XVE XV Lead free and Green 8-pin UDFN1.2x1.6 PI4ULS5V202UE U Lead free and Green 8-pin MSOP Noe: E = Pb-free Adding X Suffix= Tape/Reel Pericom Semiconducor Corporaion 1-800-435-2336 www.pericom.com Pericom reserves he righ o make changes o is producs or specificaions a any ime, wihou noice, in order o improve design or performance and o supply he bes possible produc. Pericom does no assume any responsibiliy for use of any circuiry described oher han he circuiry embodied in Pericom produc. The company makes no represenaions ha circuiry described herein is free from paen infringemen or oher righs, of Pericom. 11