CITROËN AFTER SALES DIVISION TECHNICAL SERVICES INFO DIAG DIAGNOSTIC TOOLS CITROËN SELLING DEALERS : - PDI technicians - Campaign co-ordinators AUTHORISED REPAIRERS : - Service Managers - Consultant technicians LEXIA PROXIA CD 29 N 169 15/03/2004 THE CONTENTS OF THIS BULLETIN SHOULD BE MADE KNOWN TO ALL PERSONNEL WHO, DIRECTLY OR INDIRECTLY, USE LEXIA / PROXIA DIAGNOSTIC TOOLS. CANCELS AND REPLACES INFO DIAG no. 164 of 15/03/04 Not issued in UK : One word on page 22 already corrected in GB translation of I D 164. TITLE : Aid to diagnosis of the BSI : Wash / wipe. CONCERNING : CITROËN vehicles : C2, C3, C3 pluriel, Xsara 2 (from RPO 9002), Xsara Picasso (from RPO 9492), Berlingo 2, C5, C8 Page 1 / 25
TECHNICAL SERVICES Aid to diagnosis of the BSI (G10) Wash / wipe Applying to the following CITROËN vehicles : C2 C3 C3 pluriel Xsara 2 (from RPO 9002) Berlingo 2 Xsara Picasso (from RPO 9492) C5 C8 Customer symptoms - Windscreen wipe and windscreen wash not working. - In «Automatic wipe» the speed or intermittence of the windscreen wipe is unsuitable. - Rear screen wipe not functioning. - When switched off, the windscreen wipe does not stop in the correct position. - When switched off, the rear screen wipe does not stop in the correct position. - Rear screen wipe does not operate when reverse gear engaged. - Other symptoms Page 2 / 25
Contents 1 Necessary tooling 5 2 Guarantee 5 3 Contacting your assistance team 5 3.1 INTRODUCTION 5 3.2 EXAMPLE OF THE TYPE OF INFORMATION YOU NEED TO PROVIDE 5 4 Recommendations - precautions 5 5 Functions 6 5.1 WINDSCREEN WIPE : 6 5.2 REAR SCREEN WIPE : 6 5.3 RAIN SENSOR : 6 5.4 ACTIVATION OF AUTOMATIC WIPE 6 5.5 BACK-UP MODES OF THE AUTOMATIC WIPE FUNCTION 7 5.6 IMPACT OF THE FUNCTION IN THE BSI 7 6 Configuration 7 7 [G10][S00] Preliminary checks on the BSI 8 8 [G10][S01] Windscreen wipe and windscreen wash not working 11 8.1 [G10][S01] STAGE 1 12 8.2 [G10][S01] STAGE 2 13 9 [G10][S02] In «Automatic wipe» the speed or intermittence of the windscreen wipe is unsuitable 13 9.1 CITROËN C8 AND CITROËN C5 (UP TO RPO 9617) (WIRE RAIN SENSOR) 13 9.2 CITROËN C2, C3, C3 PLURIEL, XSARA 2 (FROM RPO 9001), XSARA PICASSO (FROM RPO 9492), C5 FROM RPO 9618) 13 10 [G10][S03] Rear screen wipe does not operate when reverse gear engaged 14 11 [G10][S04] When switched off, the windscreen wipers do not stop in the correct position. 15 Page 3 / 25
12 [G10][S05] When switched off, the rear screen wiper does not stop in the correct position 15 13 [G10][S06] Checking the windscreen wipe function 16 13.1 STAGES 1 TO 3 17 13.2 STAGE 4 18 13.3 STAGES 5 TO 5.2 19 13.4 STAGES 5.3 AND 10, 10.1, 10.2 20 13.5 STAGE 5.4 21 13.6 STAGE 6 22 13.7 STAGE 7 23 14 [G10][S05] Checking the rear screen wipe function 24 Page 4 / 25
1 Necessary tooling A diagnostic tool. 2 Guarantee WARNING : The change of a BSI under guarantee is subject to an approval request. 3 Contacting your assistance team 3.1 Introduction Before contacting assistance, please be ready with the following elements: Nos. of the procedures implemented (G01 to G13) The sequence used (S0x) The stage you have reached (depends on the procedure being used) 3.2 Example of the type of information you need to provide You have implemented procedure G10 (Wipers), sequence S06 corresponding to «Check on windscreen wiper function» and you have arrived at stage N 7.2.1 in the flow chart. You will say to your contact : G10 - S06-7.2.1. 4 Recommendations - precautions Before any consequent operation, it is essential to check : the battery voltage, the fuses, that the BSI is not in back-up mode (see : Preliminary checks on the BSI below). Page 5 / 25
5 Functions 5.1 Windscreen wipe : Windscreen wipe in fast speed is controlled electrically by the engine relay unit. Windscreen wipe in slow speed is controlled electrically by the BSI. The fixed stop switch for windscreen wipe is linked to the engine relay unit. 5.2 Rear screen wipe : Rear screen wipe is controlled electrically by the BSI. The fixed stop switch(es) are linked to the BSI. 5.3 Rain sensor : There is more than one type of rain sensor : Wire rain sensor, fitted on C8, C5 (up to 9617), Multiplexed rain sensor, fitted on C2, C3, C3 Pluriel, Xsara 2, Xsara Picasso, C5 (from RPO 9618). 5.4 Activation of automatic wipe The automatic wipe function is activated by moving the wiper stalk to the «Auto» position. Activation of the automatic wipe function is confirmed by one sweep of the windscreen wipe in slow speed. After the ignition has been switched off, it is necessary to reactivate the function each time when restarting. Page 6 / 25
5.5 Back-up modes of the automatic wipe function : Possible cases : If the rain sensor is in back-up mode and automatic wipe activated, the windscreen wipers function in intermittent wipe, If there is a break in communication between the BSI and the engine relay unit, the engine relay unit commands the wipers in slow speed intermittent wipe, If there is a break in communication between the switch module under the steering wheel and the BSI, the windscreen wipers function in slow speed intermittent wipe. 5.6 Impact of the function in the BSI 6 Configuration A certain number of configuration parameters are memorised in the BSI : Parameter «Sensitivity of the automatic wipe function» (adjustable from 0 to 15) (Multiplexed rain sensor), Parameter «Rain sensor option» (yes/no), Parameter «Rain / sunlight sensor option» (yes/no). WARNING : The display of the configuration parameters depends on their presence in the BSI software. The parameters featured will be displayed by the diagnostic tool either partially or in totality according to the software version in the BSI. You can access the parameters after starting communication with the BSI using a diagnostic tool and selecting the menu MANUAL PROGRAMMING then CONFIGURATION. Page 7 / 25
7 [G10][S00] Preliminary checks on the BSI Stage 1 Identification of a BSI in back-up mode: - First case: When the ignition is switched on (+APC), the vehicle s sidelamps come on, the windscreen wiper operates in intermittent wipe, - Second case: With the engine running, the dipped beams come on, the windscreen wiper operates in intermittent wipe. Does the BSI show symptoms of being in back-up mode? No Yes End procedure Stage 2 Check the fuses, the supplies of the BSI repair if necessary Stage 3 Using a diagnostic tool, start communication with the BSI, select the menu «IDENTIFICATION» Are you able to read the software version (*) of the BSI? (*)(or the software edition) Yes Go to stage 4 No Go to stage 10 Page 8 / 25
Stage 4 Is the BSI new? (coming from Replacement Parts) Yes Stage 5 Prior to end June 2004: Replacement of the BSI authorised. From beginning July 2004: Download the BSI using the procedure for downloading of blank ECUs No Stage 6 Has the BSI been downloaded previously? Yes No Stage 8 Go to stage 10 Stage 7 Renew the downloading of the BSI at least three times. At the third attempt, the replacement of the BSI is authorised. Page 9 / 25
Stage 10 Using a diagnostic tool, start communication with the BSI. Select the menu «ACTUATOR TEST» then «LIGHTING / SIGNALLING» Carry out an actuator test on the horn Did the horn work? Yes No Stage 12 Using a diagnostic tool, start communication with the BSI. Select the menu «ACTUATOR TEST» then «LIGHTING / SIGNALLING» Carry out an actuator test on the dipped beams. Stage 11 Check the harness and the wiring Change the switch module under the steering wheel. The BSI is not the cause, replacement not authorised Did the dipped beams come on? Yes No Stage 13: End procedure The BSI is at fault, replacement authorised Stage 14: End procedure The Engine Relay Unit is faulty. The BSI is not the cause, replacement not authorised Page 10 / 25
8 [G10][S01] Windscreen wipe and windscreen wash not working Thiis procedure is divided into two stages, depending on the vehicle definition. Use the stage that applies to the vehicles as in the following table : Vehicle Stage to use C2 Stage 1 C3 Stage 1 C3 Pluriel Stage 1 Xsara 2 (from RPO 9002) Stage 2 Berlingo 2 (up to RPO 9856) Stage 1 Berlingo 2 (after RPO 9856) Stage 2 Xsara Picasso (RPO 9492 to RPO 9867) Stage 1 Xsara Picasso (after RPO 9867) Stage 2 C5 (up to RPO 9617) Stage 2 C5 (RPO 9618 to RPO 9867) Stage 1 C5 (after RPO 9868) Stage 2 C8 Stage 2 Page 11 / 25
8.1 [G10][S01] Stage 1 Preliminary operations : check that the BSI software is up-to-date, download if necessary. To solve the problem, carry out the following operations : the vehicle must be operational, sidelamps switched off, make sure that ECO mode is not active (if necessary start the engine), switch on the ignition (ignition+), disconnect the 6-way grey connector of the switch module under the steering wheel, wait for the sidelamps to come on (change to back-up mode of the BSI), switch off the ignition, wait for the BSI to go to sleep (listen for the clicking of the relay in the BSI, approx. 1 minute and thirty seconds) (*), reconnect the 6-way grey connector of the switch module under the steering wheel, switch on the ignition (ignition+), switch off the ignition, Place the wiper stalk in the «auto» position (automatic wipe), Place the wiper stalk in the «0» position», the wipers should be in the park position, Wait for the end of the sweep, you can switch the ignition back on (*) During this phase, do not move any door or action any electrical control, the diagnostic tool must not be reconnected to the vehicle. If the problem is still present, apply the checking procedure [G10][S04] «Checking the windscreen wipe function». Page 12 / 25
8.2 [G10][S01] Stage 2 Check that the BSI software is up-to-date, download the BSI if necessary. If the problem persists, apply the checking procedure [G10][S04] «Checking the windscreen wipe function». 9 [G10][S02] In «Automatic wipe», the speed or intermittence of the windscreen wipe is unsuitable. 9.1 Vehicles CITROËN C8 and CITROËN C5 (up to RPO 9617) (wire rain sensor) Operations to be carried out (without a diagnostic tool) : check the rain sensor (using water), check that the interior side of the windscreen is clean, check the positioning of the sensor on the windscreen. WARNING : The BSI is not at fault, replacement not authorised. 9.2 Vehicles CITROËN C2, C3, C3 Pluriel, Xsara 2 (after RPO 9001), Xsara Picasso (after RPO 9492), C5 (after RPO 9618) These vehicles are equipped with a multiplexed rain sensor. Operations to be carried out: Using a diagnostic tool, start communication with the BSI, Select the menus MANUAL PROGRAMMING - CONFIGURATION, Check the parameter «Sensitivity of the automatic wipe function» (adjustable from 0 to 15) (multiplexed rain sensor). Operations to be carried out (without a diagnostic tool) : check the rain sensor (using water), check that the interior side of the windscreen is clean, check the positioning of the sensor on the windscreen. WARNING : The BSI is not at fault, replacement not authorised. Page 13 / 25
10 [G10][S03] Rear screen wipe does not operate when reverse gear is engaged. Operations to be carried out (checking the programming of the function) : Using a diagnostic tool, start communication with the BSI. Select the menus MANUAL PROGRAMMING CUSTOMER OPTION and check that the function «Presence of rear screen wipe in reverse gear» is configured to «Yes» Operations to be carried out (checking the functioning of the reverse gear switch) : Engage reverse gear and check the reversing lamps If they do not work, check the reverse gear switch and its cabling If the problem is still present, apply the checking procedure «[G10][S05] Checking the rear screen wipe function». Page 14 / 25
11 [G10][S04] When switched off, the windscreen wipers do not stop in the correct position. Operations to be carried out: Using a diagnostic tool, start communication with the BSI. Then select PARAMETER MEASURES then VISIBILITY. Perform the following operations : Operate the wipers and observe the parameter «Windscreen wipers fixed stop inforrmation» If the parameter does not regularly change status (Yes / No) while the wipers are operating, check the cabling and the functioning of the fixed stop switch incorporated in the wiper motors. If the fixed stop switch incorporated in the wiper motors and the electrical cabling are in good condition, the BSI is faulty (replace the BSI). 12 [G10][S05] When switched off, the rear screen wiper does not stop in the correct position. Operations to be carried out: Using a diagnostic tool, start communication with the BSI. Then select PARAMETER MEASURES then VISIBILITY. Perform the following operations : Operate the wiper and observe the parameter «Rear screen wiper fixed stop inforrmation» If the parameter does not regularly change status (Yes / No) while the wiper is operating, check the cabling and the functioning of the fixed stop switch incorporated in the wiper motor. If the fixed stop switch incorporated in the wiper motor and the electrical cabling are in good condition, the BSI is faulty (replace the BSI). Page 15 / 25
13 [G10][S06] Checking the windscreen wipe function This test procedure should be adopted in all cases where you have doubt concerning the functioning of the wipers, for all symptoms: for example the following symptoms: When switched off, the windscreen wipers do not stop in the correct position Other symptoms concerning the windscreen wipers Page 16 / 25
13.1 Stages 1 to 3 STAGE 1 Using the diagnostic tool, start communication with the BSI. From the menu MANUAL PROGRAMMING CONFIGURATION check the configuration of the parameters «Rain sensor option» and «Rain/sunlight sensor option» STAGE 2 Do the wipers operate in fast speed and in slow speed using the wiper control stalk? Yes Go to Stage 5 Diagnosis of automatic wipe mode No STAGE 3 Place the wiper stalk in the slow speed position. Do the windscreen wipers operate? No Go to Stage 6 Diagnosis of operation in slow speed Yes Go to Stage 4 Page 17 / 25
13.2 Stage 4 From Stage 3 Yes STAGE 4 Place the wiper stalk in the fast speed position. Do the windscreen wipers operate? Yes Go to Stage 5 Diagnosis of the «Automatic wipe» function No Go to Stage 7 Diagnosis of operation in fast speed. Page 18 / 25
13.3 Stage 5 to 5.2 Stage 5 Diagnosis of automatic wipe mode STAGE 5.1 Is the rain sensor wire or multiplexed? Vehicles N7, C5 (up to RPO 9617) (wire rain sensor) Vehicles C2, C3, C3 Pluriel, Xsara Picasso, C5 (from RPO 9618) (multiplexed rain sensor) 5.1.1 END PROCEDURE Check the electrical harness of the rain sensor Check the surface of the rain sensor (clean it if necessary) Change the sensor. Change the BSI in the last resort STAGE 5.2 Activate automatic wipe in order to re-initialise the system. Automatic wipe is activated Activation of automatic wipe is impossible 5.2.1 Go to Stage 5.4 Go to Stage 5.3 Page 19 / 25
13.4 Stage 5.3 and 10, 10.1, 10.2 STAGE 5.3 Start the engine, activate the automatic wipe function using the wiper control stalk The wipers operate at slow speed intermittent The wiper does not operate at all 5.3.1 The wipers are operating at slow speed intermittent The rain sensor is faulty STAGE 10 Using the diagnostic tool, start communication with the switch module under the steering wheel. Selection the menus «PARAMETER MEASURES» then «WIPER CONTROL» Move the wiper stalk and observe the corresponding parameters The parameters change according to the position of the wiper control stalk The parameters do not change according to the position of the wiper control stalk 10.2 Replacement of the BSI not authorised. Contact your technical assistance 10.1 The switch module under the steering wheel is faulty Page 20 / 25
13.5 Stage 5.4 STAGE 5.4 Automatic wipe is activated. Did the windscreen wipers operate once? The windscreen wipers operated once The windscreen wipers did not operate 5.4.1 END PROCEDURE The BSI is not the cause, replacement not authorised. STAGE 5.5 Using the diagnostic tool, start communication with the switch module under the steering wheel. Select the menus «PARAMETER MEASURES» then «WIPER CONTROL» Move the wiper stalk and observe the corresponding parameters The parameters change according to the position of the wiper control stalk The parameters do not change according to the position of the wiper control stalk 5.5.1 END PROCEDURE Contact your technical assistance, replacement not authorised. 5.5.2 END PROCEDURE The switch module under the steering wheel is faulty. The BSI is not at fault. Page 21 / 25
13.6 Stage 6 Stage 6 Diagnosis of manual functioning in slow speed STAGE 6.1 Using the diagnostic tool, start communication with the BSI. Select the menus «PARAMETER MEASURES» then «VISIBILITY» Move the wiper stalk and observe the corresponding parameters The corresponding parameters are incorrect Go to Stage 7 Diagnosis of fast speed mode The corresponding parameters are correct STAGE 6.2 Using a diagnostic tool, perform an actuator test of the windscreen wiper The windscreen wipers do not move during the actuator test The windscreen wipers move during the actuator test 6.2.1 END PROCEDURE Check the electric motors Check the harnesses. If the electric motors and the harnesses are in good condition, replacement of the BSI should resolve the problem. 6.2.2 END PROCEDURE Contact your technical assistance, replacement not authorised Page 22 / 25
13.7 Stage 7 Stage 7 Diagnosis of fast speed STAGE 7.1 Using the diagnostic tool, start diagnosis with the switch module under the steering wheel. Select the menus «PARAMETER MEASURES» then «WIPER CONTROL» Move the wiper stalk and observe the corresponding parameters The parameters do not change according to the position of the wiper control stalk The parameters change according to the position of the wiper control stalk 7.1.1 END PROCEDURE The switch module under the steering wheel is faulty The BSI is not at fault, replacement not authorised. STAGE 7.2 Switch on the dipped beams. Do the dipped beams come on? The dipped beams come on The dipped beams do not come on 7.2.1 END PROCEDURE The BSI is faulty 7.2.2 END PROCEDURE The relay internal to the engine relay unit is faulty. The BSI is not at fault, replacement not authorised. Page 23 / 25
14 [G10][S05] Checking the rear screen wipe function This test procedure should be adopted in all cases where you have doubt concerning the functioning of the wipers. For example the following symptoms: The rear screen wiper does not function When switched off, the rear screen wiper does not stop in the correct position Other symptoms concerning the rear screen wiper Page 24 / 25
Stage 1 Checking the rear screen wiper STAGE 2 Using the diagnostic tool, start communication with the BSI. Action the rear wiper control. Check the parameters corresponding to the rear wiper controls The parameters are not functional The parameters are functional 4 END PROCEDURE The BSI is not at fault. Check the functioning of the switch module under the steering wheel. STAGE 3 Using the diagnostic tool, perform an actuator test of the rear screen wiper. Did the rear screen wiper move? Yes No 3.1 END PROCEDURE Check the electric motors - Check the harnesses If the electric motors and the harnesses are in good condition, replacement of the BSI should resolve the problem. 3.2 END PROCEDURE Replacement of the BSI not authorised Contact your technical assistance Page 25 / 25