Automotive Data Solutions Inc. INSTALL GUIDE BLADE-AL(DL)-GM GM Available for : ADS-BLADE AL Rev. Date: October 04, 0 Doc. No.: ##666## 0004 Version FRançaise disponible en ligne au www.bladeuptade.com please visit www.bladeupdate.com for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
XX-XX ADS-AL(DL)-GM - PAGE X-X -3 install TYPE SELECTiOn FeATUReS Page of 7 BLADE-AL(DL)-GM Doc. No.: ##666## 0004 MAKe MoDel YeAR install TYPe DATA immobilizer BYPASS BUiCK CADillAC ARM oem AlARM CHeVRoleT DiSARM oem AlARM DooR lock DooR UnloCK PRioRiTY UnloCK TRUnK/HATCH ReleASe PoWeR SliDinG DooR (l) PoWeR SliDinG DooR (R) RAP SHUTDoWn CTRl ReAR DeFRoST CTRl* HeATeD SeATS CTRl* TACHoMeTeR output** DooR STAT output FRonT (l) DooR STAT output FRonT (R) DooR STAT output ReAR (l) DooR STAT output ReAR (R) TRUnK STAT output Allure 05-09 3 Century 00-05 LaCrosse 05-09 3 LeSabre / Ultra 00-05 3 Park Avenue 97-05 3 Rainier 04-07 3 Regal 00-04 Rendez-vous 0-07 Terraza 05-07 3 CTS 03-07 3 Deville 00-05 3 Escallade 99-0 Escallade 03-06 3 Escallade EXT 03-06 3 Seville 98-03 3 SLS 98-99 SLS 00-04 3 SRX 04-06 3 STS 98-99 STS 00-04 3 Astro 98-05 Avalanche 0 Avalanche 03-06 3 Blazer 98-05 Cavalier 00-05 Express 03-07 Express 98-0 Impala 00-05 Monte Carlo 00-05 S0 / S5 98-04 Silverado 99-0 Silverado 03-06 3 SSR 04-06 3 Suburban 99-0 Suburban 03-06 3 Tahoe 99-0 Tahoe 03-06 3 Trailblazer 0-09 3 Uplander 05-09 3 Venture 00-04 * See heated accessories notice. ** Tach output is not available on vehicles with a duramax engine. The PK3 indicator will remain ON during the remote start sequence and will only turn OFF upon takeover. Tach output is not available on these vehicles if they are equipped with a V8 engine.
XX-XX ADS-AL(DL)-GM - PAGE X-X 3-3 install TYPE SELECTiOn FeATUReS Page 3 of 7 BLADE-AL(DL)-GM Doc. No.: ##666## 0004 MAKe MoDel YeAR install TYPe DATA immobilizer BYPASS ARM oem AlARM SATURn SAAB PonTiAC oldsmobile isuzu GMC HUMMeR DiSARM oem AlARM DooR lock DooR UnloCK PRioRiTY UnloCK TRUnK/HATCH ReleASe PoWeR SliDinG DooR (l) PoWeR SliDinG DooR (R) RAP SHUTDoWn CTRl ReAR DeFRoST CTRl* HeATeD SeATS CTRl* TACHoMeTeR output** DooR STAT output FRonT (l) DooR STAT output FRonT (R) DooR STAT output ReAR (l) DooR STAT output ReAR (R) TRUnK STAT output H 03-07 3 Envoy 98-0 Envoy 0-09 3 Jimmy 98-05 Safari 98-05 Savana 98-0 Savana 03-07 Sierra / CK 98-0 Sierra / CK 03-06 3 Sonoma 98-04 Yukon / Denali 99-0 Yukon / Denali 03-06 3 Ascender 03-08 3 Hombre 98-00 Alero 4cyl 99-0 Alero 4cyl 0-04 Alero 6cyl 99-04 Aurora 00-03 3 Bravada 98-0 Bravada 0-04 3 Intrigue 98-99 Intrigue 00-0 Silhouette 00-04 Aztek 0-05 Bonneville 00-05 3 Grand Am 4cyl 99-0 Grand Am 4cyl 0-05 Grand Am 6cyl 99-05 Grand Prix 04-08 3 Montana 00-04 Montana SV6 05-09 3 Sunfire 00-05 97x 06-09 3 Relay 05-07 3 * See heated accessories notice. ** Tach output is not available on vehicles with a duramax engine. The PK3 indicator will remain ON during the remote start sequence and will only turn OFF upon takeover. Tach output is not available on these vehicles if they are equipped with a V8 engine.
XX-XX BLADE-AL(DL)-GM PAGE X-X Guides Français USE THE FOLLOWING disponibles LAYER au WWW.BLADEUPDATE.COM SPECIFIC ITEMS AS WIRING AND TEXT TEMPLATES Page 4 of 7 BLADE-AL(DL)-GM Doc. No.: ##666## 0004 MOVE THE FOLLOWING ITEMS IN YOUR SCHEMATIC WITH ALL LAYERS ON NOTE YER SPECIFIC ITEMS AS XT TEMPLATES I II BLUE/ View compatibility chart for applicable vehicles. GREEN/ in all supported vehicle, heated accessories BLUE/ will automatically RED/ be activated 5 seconds after the remote BROWNstarter is engaged PURPLE/ and this only if the engine temperature ENABLE - PURPLE/ is below 0 C (3 F). / /RED BROWN/ / / / BLUE/ GRAY/RED - DISABLE GRAY/ RED / GREEN HEATED ACCESSOriES notice notice PURPLE/ To disable this feature, connect [gray/red] wire to ground. / /RED BROWN/ / / / BLUE/ - ENABLE GRAY/ To activate applicable heated accessories upon remote start regardless of engine temperature, connect [green/ red] wire to ground. /NOIR /ROUGE JAUNE BRUN/ROUGE BRUN/JAUNE /NOIR / REMOTE STARTER ROSE/NOIR ROSE BLEU/ROUGE BLEU/JAUNE VERT/ROUGE GRIS/ROUGE - DESACTIVER GRIS/JAUNE NOIR BLEU/ NOIR ROUGE VERT/NOIR BLEU/NOIR ROUGE/ BRUN MAUVE/JAUNE ACTIVER - MAUVE/NOIR NOIR/ VERT MAUVE/ NOIR TYPE - wiring DIAGRAM /NOIR /ROUGE JAUNE BRUN/ROUGE BRUN/JAUNE /NOIR / ROSE/NOIR ROSE BLEU/ROUGE BLEU/JAUNE VERT/ROUGE - ACTIVER GRIS/ROUGE GRIS/JAUNE RELOCK AFTER START MUST BE ENABLED TO AVOID VEHICLE DOORS TO REMAIN UNLOCKED DURING REMOTE START SEQUENCE /RED / / *BLADE CONNECTOR EXACT PIN-OUT GRAY/RED 0 0 09 9 08 8 07 7 06 6 05 5 04 4 03 3 0 0 / BROWN/ / BLUE/ GRAY/ BLADE CONNECTOR* / (NC) /RED (NC) (NC) (NC) (NC) BROWN/ (NC) / (NC) / (NC) - DATA (J850) / (NC) (NC) (NC) BLUE/ (NC) (NC) GRAY/ (NC) (NC) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH DATA 3 4 5 6 7 8 9 0 3 4 5 6
Page 5 of 7 BLADE-AL(DL)-GM Doc. No.: ##666## 0004 TYPE - wiring DIAGRAM REMOTE STARTER PK3 PASS KEY III THEFT DETERRENT : MODULE, BEHIND DRIVER SIDE DASH, RIGHT OF STEERING COLUMN / (-) /RED / / *BLADE CONNECTOR EXACT PIN-OUT GRAY/RED 0 0 09 9 08 8 07 7 06 6 05 5 04 4 03 3 0 0 / BROWN/ / BLUE/ GRAY/ BLADE CONNECTOR* /- GROUND (-) /RED (NC) - STARTER ENABLE (-) OUTPUT (NC) (NC) BROWN/ (NC) / (NC) / (NC) - DATA (J850) / (NC) (NC) (NC) BLUE/ (NC) (NC) GRAY/ (NC) (NC) 3 4 5 6 7 8 OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 9 DATA 0 3 4 5 6 TYPE 3 - wiring DIAGRAM REMOTE STARTER /RED / / *BLADE CONNECTOR EXACT PIN-OUT GRAY/RED 0 0 09 9 08 8 07 7 06 6 05 5 04 4 03 3 0 0 / BROWN/ / BLUE/ GRAY/ BLADE CONNECTOR* / (NC) /RED (NC) (NC) (NC) (NC) BROWN/ (NC) / (NC) / (NC) - DATA (J850) / (NC) (NC) (NC) BLUE/ (NC) (NC) GRAY/ (NC) (NC) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH DATA 3 4 5 6 7 8 9 0 3 4 5 6
XX-XX BLADE-AL(DL)-GM BLADE-AL(DL)-GM 57 PAGE X-X Page 6 of 7 BLADE-AL(DL)-GM Doc. No.: ##666## 0004 CArTriDgE installation Slide cartridge into unit. Notice button under LED. Ready for Module Programming Procedure. MODULE PrOgrAMMing PrOCEDUrE Insert key into ignition. 3 Wait, LED will turn solid BLUE for seconds. START Turn key to START position. 4 OFF Turn key to OFF position. 5 Module Programming Procedure completed.
BLADE-AL XX-XX PATENT PAGE X-X - identify VEHiCLE notice YEAr Page 7 of 7 BLADE-AL(DL)-GM Doc. No.: ##666## 0004 Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. l > 990 S > 995 Y > 000 5 > 005 A > 00 M > 99 T > 996 > 00 6 > 006 B > 0 n > 99 V > 997 > 00 7 > 007 C > 0 P > 993 W > 998 3 > 003 8 > 008 D > 03 R > 994 X > 999 4 > 004 9 > 009 e > 04 led STATUS Flashing RED DiAGnoSTiCS DURinG PRoGRAMMinG DURinG ReMoTe START WiTH ignition off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing BLUE Additional steps required to complete programming MODULE DiAgnOSTiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid BLUE then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE DISCONNECT cartridge from remote starter. 3 LED will flash red. Immediately RELEASE programming button. PRESS AND HOLD programming button while re-connecting cartridge to remote starter. 4 LED will turn solid red for seconds. RESET COMPLETED. 5! RECONNECT all connectors. Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. This product is protected by one or more of the following patents: U.S. LETTErS PATEnT no. 5,79,55; 6,0,460; 6,43,004; 6,49,6; 6,75,47; 6,97,73; 6,346,876; 6,39,534; 6,59,4; 6,696,97; 6,756,885; 6,756,886; 6,77,67; 6,8,89; 6,94,750; 7,00,40; 7,03,86; 7,046,6; 7,06,37; 7,068,53; 7,05,830; 7,05,679; 7,4,083; 7,369,936; 7,378,945; 7,489,33; 7,50,937; CAnADiAn PATEnT no.,30,48;,45,03;,46,670;,44,99;,45,0;,45,07;,45,038;,45,04;,50,893;,45,490;,45,96;,45,487; EUrOPEAn PATEnT no.,053,8; DE 69807-94T; U.S. 00045535; 006098; 0060984; 00400784; 008003036; 009007955; EP500565; 538038; 538037;