Vessel Specification - December 2011 GOLIATH DPIII OFFSHORE SUPPORT VESSEL This technical specification sheet is subject to change without notice.whilst every effort has been made to ensure that accuracy of the information represented within this document, no guarantees of accuracy can be given
GOLIATH The Goliath is one of the largest offshore construction vessels in the world. This multi-functional vessel is equipped with DPIII and a 1600mt crane, primarily for offshore installation. The Goliath can be readily equipped for pipelaying as welll as saturation diving and a variety of other functions. The vessel also has substantial accomodation in the form of 300 high-quality berths. The heavy lifting test of the large crane was carried out in the open sea with a 1,760 t test weight corresponding to 110% of the nominal load capacity. The test loads consisted of two water filled pontoons which were lifted out of the water and turned around. BUILT: 2009 Dry Dock World Pertama FLAG: Panama CLASS: ABS + A1 + (E) + AMS + ACCU + ICE CO + DP3 + HE LIDECK + ES + FiFi 2 DIMENSIONS LOA: 180m LWL: 167.8m Beam: 32m Displacement: 35500 tonnes Deadweight: 22000 tonnes Draft (design): 7.0 metres Draft (scantling): 7.5 metres Draft: 10.5 metres Forward Thrusters Extended BOLLARD PULL: 250 tonnes HELIDECK: Designed for Sikorsky S61N helicopter CARGO AND DECK SPACE: Below Deck Storage: Space 4 Cargo Holds 3 Cargo Holds Deck Cargo Space: 5000 sq metres Deck Loading: 10 tons / sq metre and 5 tons / sg metre CAPACITIES Fuel Capacity: 7500 m³ Fresh Water Capacity: 2700 m³ Ballast Water Capacity: 5000 m³ Lub Oil Capacity: 15 m³ Water Ballast: WBT 8590mt Anti-rolling: 7640mt ACCOMODATION: The vessel is rated to carry 296 personnel, although she actually has 314 bunks. Available for the client will be roughly 240 berths, once extra catering crew are in place to look after them. There are 5 offices and 2 conference rooms available to the client. The mess room will seat 150 at one time, and there is a large recreation room provided as well as a 24-seat cinema. A fully fitted gym and sauna are also fitted, as well as a swimming pool installed above the bridge. CRANEAGE Main Crane: Liebherr 1600mt (fully revolvable) with 70 metre Boom mounted SB Side Auxiliary Cranes: 2 x 100mt revolving lifting 100mt at 18m radius. Boom length of 48m with whip line of 20mt with subsea capacity of 50mt at 34m radius with 300m depth SPEED, CONSUMPTION AND ENDURANCE Max Speed: 14 knots 100% MCR General Service Speed: 12 knots 90% MCR Consumption in Transit: 39 mt / day Consumption on DP 15 mt / day Consumption alongside 5 mt / day Endurance: 100 days offshore GENERATORS Eight Caterpillar 3516C engines drive generators supplied by Leroy Summers. Each generator outputs 2,200 kilowatts, giving a total of 17,600 kilowatts available. An emergency generator with a Caterpillar 3500B engine is installed, which outputs 1424 kilowatts.
THRUSTERS Aft: Three Rolls Royce azimuth thrusters, each of 3,333 kilowatts. Fwd: Two Rolls Royce drop-down azimuth thrusters, each of 2,400 kilowatts, plus Two Rolls Royce tunnel thrusters, each of 1,355 kilowatts. All thrusters are powered by frequency-drive motors supplied by Wartsila. Total thruster power available is 17, 509 kilowatts. 2 MOONPOOLS Each 4m x 3m (hatch cover) DP SYSTEM Kongsberg K-Pos dual redundant main operating station on aft bridge. Kongsberg K-Pos simplex back-up operating station on forward bridge. Kongsberg C-Joy independant joysticks on forward and aft bridges. Kongsberg C-Wing remote joystick, with plug-in point port and starboard. 1 x HiPAP acoustic position reference system, with two 500mm transducers. 2 x Differential GPS position reference systems. 2 x Bandak Mk 15B taut wire position reference systems. Port and starboard. 2 x Fanbeam short-range laser position reference systems. Forward and aft. LIFEBOATS / HIGH SPEED CRAFT 4 x 102 person enclosed lifeboats 2 x 35knot SOLAS 144 HS crafts 8 x throw-over rafts (KHZ-50) HELICOPTER ACCESS 12.8t, 23m diameter heli-deck
CRANEAGE MTC 7800 MAIN CRANE C R A N E S The MTC 78000 achieves a maximum lifting capacity of 1,600 t at up to 35 m radius. This corresponds to a maximum dynamic moment of 78,000 mt, the crane still being able to slew over 360. At a maximum radius of 74 m for the main hoist the crane achieves a lifting capacity of almost 530 t. The boom length of the crane currently delivered is 87 m. In addi-tion to the main hoist, the MTC 78000 offers two auxiliary hoists with lifting capacities of up to 200 t and 50 t respectively. The drive concept is based on an electro-hydraulic drive with 8 x 500 kw or 4 MW power. The two main winches offer a line pull of 500 kn (50 t) with a rope diameter of 48 mm. High safety standards are among the most important criteria to be fulfilled during the development of the new offshore crane. The standard equipment of the MTC 78000 features the proven Litronic control system with integrated display of load and radius as well as automatic load moment limitation. This is completed by special overload protections which are either activated electronically (AOPS automatic overload protection system ) or manually (MOPS manual overload protection sys-tem ). The crane's auxiliary hoist is fitted with a constant ten-sion system exerting a tensile force on the hoist rope in case of significant wave height, thus ensuring that the hook follows the moving load. The vessel is further equipped with 2 x 100 t Litronic cranes.
2 x CBO 3600 100 Litronic ancillary cranes
For further information, please contact: Alex Vicefield Zafiro Marine info@zafiromarine.com +377 92 05 10 20 This technical specification sheet is subject to change without notice. Whilst every effort has been made to ensure that accuracy of the information represented within this document, no guarantees of accuracy can be given