Retail Reception kiosk put 42" corner post in below 66" to allow post to extend above kiosk for raised box sign Mini cantilever option - 24" overhead support leg Mini cantilever option - 24" overhead 66/48E 66/24E 66/60E 66/24E 66/30E option - 30" overhead 66/30 42/24 5901 24x54 1081 1081 1081 1081 24x54 5901 66/42 42/24 66/36 66/36 support leg spanner rail
Retail privacy kiosk put 42" corner post in below 66" to allow post to extend above kiosk for raised box sign Mini cantilever option - 24" overhead support leg Mini cantilever option - 24" overhead 66/48E 66/24E 66/60E 66/24E 66/30E 5901 66/42 1081 1081 24x54 1081 1081 24x54 5901 66/42 66/36 66/36 support leg spanner rail
Tools that will help you set up your kiosk 1. Rubber mallet 2. Cordless screw gun 12v or higher is better. It can be done with screwdrivers but the process is much easier with this tool. a. # 2 Phillips bit b. ¼ and 3/8 socket (might not be necessary) 3. Small level (optional) 4. Pliers 5. Box cutter 6. Flat blade screwdriver (to open metal raceways on panels) 7. 5 in 1 painter s tool (priceless when taking apart panels). Use to pull plastic connectors out of panels. Sample of 5 in 1 painters tool Other helpful hints Cleaning Kiosk panels are laminate and easily cleanable. Use an alcohol or ammonia based cleaner such as Windex to wipe down panels. Cleaners with any polish will streak and not look good. When storing your kiosk, take care in how you place the panels. Taking care will protect the panels and increase the life span of your kiosk. Most damage happens in the take down and transport of the kiosk. Have a box to store the small parts. Mark it well so you will have all the parts for next season. Do not store the panels flat. It is best to stack them against a wall. Poly wrapping the panels or placing some cardboard between each panel will help protect them.
Installation Instructions Jackson Hewitt Retail Kiosk General Kiosk Installation: Begin with 42" high panels positioned 90 degrees to each with connector post. Continue to build outside panels, clockwise per the layout. On two remaining panels install leg spacer first, then spanner rails into slots at height of leg. Screw on 12" leg to spacer. Note: Panels will have legs on opposite sides. Install worksurfaces Install 24x24 counter top. Install 30" steel overhead assy Install 24" steel overhead assy Install 24" tackboard. Unit by Unit Instructions: 1. Organize panels by size and open all panel hardware items. Carefully remove all panel Radius Top Caps. Screw out panel leveling glides apx. 1/4". Top Cap Leveling Glides 2. Begin with 42" high x 24" wide, non-electrical panel. Maxon Furniture Inc. an HNI Corporation company www.maxoninfo.com Customer Service 1-800-876-4274 REV. A November 2007 SHEET 1 OF 6
3. Install 42" high corner post. Place in slot at lower side of panel. Set corner post on bracket and slide in plastic into both panel & post t-slots. Cut off any excess just below aluminum frame. (See Parallel Panel Connection Instructions for details). 4. Install next 42" high x 24" wide, non-electrical panel. Adjust leveling glides to same height as first panel. Place Angle Alignment Bracket into panel slot near frame bottom so panel is 90 degrees to first. Slide panel along connector post so Angle Alignment Bracket engages in panel slot. Slide in plastic. Cut off any excess. Angle Alignment Bracket Corner Post Leveling Glides 5.Install 66" high x 30" wide, non-electrical panel. Adjust leveling glides. Place in lower panel slot. Slide in plastic to height of lower panel. Cut off any excess. Leveling Glide 6. Install 42" high corner post. Place in slot at lower side of panel. Set corner post on bracket and slide in plastic into both panel & post t-slots. Cut off any excess just below aluminum frame. (See Parallel Panel Connection Instructions for details). 7. Install 66" high x 48" wide, electrical panel. Adjust leveling glides. Place Angle Alignment Bracket into panel slot near frame bottom so panel is 90 degrees. Slide panel along connector post so Angle Alignment Bracket engages in panel slot. Slide in plastic. Cut off any excess. Angle Alignment Bracket Corner Post Leveling Glides SHEET 2 OF 6
8. Install 66" high corner post on top of 42" corner post. Slide corner post from above panels down onto plastic. Corner Post 9. Install 66" high x 24" wide, electrical panel. Adjust leveling glides. Place into lower panel slot. Slide in plastic. Cut off any excess. Leveling Glide 10.Install 66" high x 60" wide, electrical panel. Adjust leveling glides. Place in lower panel slot. Slide in plastic. Cut off any excess. Leveling Glide 11.Install 66" high x 24" wide, electrical panel. Adjust leveling glides. Place in lower panel slot. Slide in plastic. Cut off any excess. Leveling Glide 12.Install 66" high x 30" wide, electrical panel. Adjust leveling glides. Place in lower panel slot. Slide in plastic. Cut off any excess. Leveling Glide SHEET 3 OF 6
13. Install 66" high corner post. Place in slot at lower side of panel. Set corner post on bracket and slide in plastic into both panel & post t-slots. Cut off any excess just below aluminum frame. (See Parallel Panel Connection Instructions for details). Corner Post 14. Install 66" high x 42" wide, non-electrical panel. Adjust leveling glides. Place Angle Alignment Bracket into panel slot near frame bottom so panel is 90 degrees. Slide panel along connector post so Angle Alignment Bracket engages in panel slot. Slide in plastic. Cut off any excess. Angle Alignment Bracket Leveling Glides 15. Get 66" high x 36" wide, non-electrical panel. Place accross from 24" wide panel. Install Spanner Rail with spanner rail mini-cantilievers into panel slots at about 28" from the floor, and install the brace clip onto the panel's bottom rail. (see instructions) Install two panel mount mini-cantilever brackets on the 24" wide panel at 28" from the floor (see instructions) Spanner rail mini cantilevers. Panel mount mini cantilevers. Mount on 24" wide panel. 16. Get 54" long x 24" deep worksurface. Place worksurface on all four mini-cantilevers aligning with inserts on bottom of the worksurface. Screw in machine screws to attach worksurface (8 places) 17. Get Panel Brace. Slide "hooked" end under the 36" wide panel where the brace clip is located. Screw in the machine screw to attach the brace to the worksurface. Screw the panel brace to the sides of the brace clip with two Black Screws. (See instructions) 18. Repeat steps 15 thru 17 for other panel/worksurface. SHEET 4 OF 6
19. Install panel lock bar at straight panel connections (4 places). Install Lock Bar, bridging straight panel connections, using self-tapping screws. Make certain Lock Bar is centered between panels. (See Instructions) Lock Bar 20. Install metal Wedge Brackets at all panel to corner post connections (See instructions). (2 places - not on tall Sign Post corner) 20. Install panel Radius Top Caps back onto all panels. Top Cap 21. Install Corner Post Caps on open corner posts. (2 places - not on tall Sign Post Corner). 22. Install plastic Radius End Caps on all open ends of Radius Top Caps (7 places). Radius End Cap SHEET 5 OF 6
23. Install 24" Corner Counter Top per instructions. Place LH & RH Countertop Brackets in top panel slots on each side of both panels (8 brackets) Note: top flange should be inward. Place Counter Top surface on brackets and screw together. 24. Install 30" Steel Overhead Storage at corner (sign post) per instruction sheet. Place LH & RH End Panels into panel slots at top of panel. (Note: bends inward). Place Back Strip into panel slot at bottom of end panels. Snap Lower Shelf flanges into End Panel lower strips. Note: Key slot to front. Screw in Back Strip to underside flange of Lower Shelf. Snap Upper Shelf flanges into End Panel upper strips. Remove Keys from Door Slide. Place Door with Slides forward and mounting hinge down, aligning with holes on top. Screw in Door Slides (6 places). Align as necessary. Close and test key / locking of door. 25. Install 24" Steel Overhead Storage similar to step 24. 26. Install 24" Tack Board under Overhead Storage per instructions. Adjust and install into panel slots at desired height. SHEET 6 OF 6
42/60 42/60 42/24 30/2 24x60 24x60 18x42 42/24 66/24 66/24 1081 1081 1081 1081 24x48 24x48 66/30 66/24 66/24 11' 3 1/4" 5901 5901 66/30 66/36 66/48 10' 4" 66/36 Jackson Hewitt Tax Service 2 station mall kiosk
66/30 1081 66/42 1081 8' 10" 66/24 24x54 66/36 5901 66/48 2H 30W 66/30 42/24 42/24