BFR843EL3 SiGe:C Low Noise RF Transistor in broad Band LTE (7-38 MHz) LNA Application Application Note AN328 Revision: Rev. 1. RF and Protection Devices
Edition Published by Infineon Technologies AG 81726 Munich, Germany 213 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.
Application Note AN328 Revision History: Previous Revision: No previous revision Page Subjects (major changes since last revision) Trademarks of Infineon Technologies AG AURIX, C166, CanPAK, CIPOS, CIPURSE, EconoPACK, CoolMOS, CoolSET, CORECONTROL, CROSSAVE, DAVE, DI-POL, EasyPIM, EconoBRIDGE, EconoDUAL, EconoPIM, EconoPACK, EiceDRIVER, eupec, FCOS, HITFET, HybridPACK, I²RF, ISOFACE, IsoPACK, MIPAQ, ModSTACK, my-d, NovalithIC, OptiMOS, ORIGA, POWERCODE, PRIMARION, PrimePACK, PrimeSTACK, PRO-SIL, PROFET, RASIC, ReverSave, SatRIC, SIEGET, SINDRION, SIPMOS, SmartLEWIS, SOLID FLASH, TEMPFET, thinq!, TRENCHSTOP, TriCore. Other Trademarks Advance Design System (ADS) of Agilent Technologies, AMBA, ARM, MULTI-ICE, KEIL, PRIMECELL, REALVIEW, THUMB, µvision of ARM Limited, UK. AUTOSAR is licensed by AUTOSAR development partnership. Bluetooth of Bluetooth SIG Inc. CAT-iq of DECT Forum. COLOSSUS, FirstGPS of Trimble Navigation Ltd. EMV of EMVCo, LLC (Visa Holdings Inc.). EPCOS of Epcos AG. FLEXGO of Microsoft Corporation. FlexRay is licensed by FlexRay Consortium. HYPERTERMINAL of Hilgraeve Incorporated. IEC of Commission Electrotechnique Internationale. IrDA of Infrared Data Association Corporation. ISO of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB of MathWorks, Inc. MAXIM of Maxim Integrated Products, Inc. MICROTEC, NUCLEUS of Mentor Graphics Corporation. MIPI of MIPI Alliance, Inc. MIPS of MIPS Technologies, Inc., USA. murata of MURATA MANUFACTURING CO., MICROWAVE OFFICE (MWO) of Applied Wave Research Inc., OmniVision of OmniVision Technologies, Inc. Openwave Openwave Systems Inc. RED HAT Red Hat, Inc. RFMD RF Micro Devices, Inc. SIRIUS of Sirius Satellite Radio Inc. SOLARIS of Sun Microsystems, Inc. SPANSION of Spansion LLC Ltd. Symbian of Symbian Software Limited. TAIYO YUDEN of Taiyo Yuden Co. TEAKLITE of CEVA, Inc. TEKTRONIX of Tektronix Inc. TOKO of TOKO KABUSHIKI KAISHA TA. UNIX of X/Open Company Limited. VERILOG, PALLADIUM of Cadence Design Systems, Inc. VLYNQ of Texas Instruments Incorporated. VXWORKS, WIND RIVER of WIND RIVER SYSTEMS, INC. ZETEX of Diodes Zetex Limited. Last Trademarks Update 211-11-11 Application Note AN328, Rev. 1. 3 / 35
List of Content, Figures and Tables Table of Content 1 Introduction... 6 1.1 Multiband / Broad-Band LNAs for 3G/3.5G/4G Modems... 8 2 BFR843EL3 Overview... 11 2.1 Features... 11 2.2 Key Applications of BFR843EL3... 11 3 BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications... 12 3.1 Description... 12 3.2 Performance Overview... 14 3.3 Schematics and Bill-of-Materials... 19 4 Measurement Graphs... 2 5 Evaluation Board and Layout Information... 32 6 Authors... 34 List of Figures Figure 1 Example of Application Diagram of 2G/3G/4G Front-end System... 6 Figure 2 Example of Application Diagram of 2G/3G/4G Front-end System using BFR843EL3 Broad-Band LNA... 1 Figure 3 BFR843EL3 in TSLP-3-9... 11 Figure 4 Package and pin connections of BFR843EL3 in Topview... 12 Figure 5 Schematic Diagram of the Application Circuit... 19 Figure 6 Power Gain of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3... 2 Figure 7 Reverse Isolation of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3... 2 Figure 8 Noise Figure of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3... 21 Figure 9 Input Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3... 21 Figure 1 Input Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 (Smith Chart)... 22 Figure 11 Output Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3... 22 Figure 12 Output Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 (Smith Chart)... 23 Figure 13 Stability K Factor of the Broad-Band LTE LNA with BFR843EL3... 23 Figure 14 Stability Mu Factor of the Broad-Band LTE LNA with BFR843EL3... 24 Figure 15 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 86 MHz)... 24 Figure 16 Figure 17 Input 1dB Compression Point of Broad-Band LTE LNA with BFR843EL3 (Measured at 153 MHz)25 Input Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 19 MHz)... 25 Figure 18 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 214 MHz)... 26 Figure 19 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 262 MHz)... 26 Figure 2 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 35 MHz)... 27 Figure 21 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 37 MHz)... 27 Figure 22 Figure 23 Figure 24 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 86 MHz (LNA input power = -3 dbm)... 28 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 153 MHz (LNA input power = -3 dbm)... 28 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 19 MHz (LNA input power = -3 dbm)... 29 Application Note AN328, Rev. 1. 4 / 35
List of Content, Figures and Tables Figure 25 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 214 MHz (LNA input power = -3 dbm)... 29 Figure 26 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 262 MHz (LNA input power = -3 dbm)... 3 Figure 27 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 35 MHz (LNA input power = -3 dbm)... 3 Figure 28 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 37 MHz (LNA input power = -3 dbm)... 31 Figure 29 Photo Picture of Evaluation Board for 7 38 MHz Broad-Band LTE LNA with BFR843EL3... 32 Figure 3 Zoom-In of Photo Picture... 32 Figure 31 Layout Proposal for RF Grounding of the 7 38 MHz Broad-Band LTE LNA with BFR843EL333 Figure 32 PCB Layer Information... 33 List of Tables Table 1 LTE Band Assignment... 7 Table 2 Summary of Measurement Results of Band 5, 6, 12, 13, 14, 17, 18, 19, 2, 26, 27, 28, 44 (at room temperature)... 14 Table 3 Summary of Measurement Results of Band 11, 21, 24 (at room temperature)... 15 Table 4 Summary of Measurement Results of Band 2, 3, 9, 25, 33, 35, 36, 37, 39 (at room temperature)... 15 Table 5 Summary of Measurement Results of Band 1, 4, 1 (at room temperature)... 16 Table 6 Summary of Measurement Results of Band 23 (at room temperature)... 16 Table 7 Summary of Measurement Results of Band 4 (at room temperature)... 17 Table 8 Summary of Measurement Results of Band 7, 38, 41 (at room temperature)... 17 Table 9 Summary of Measurement Results of Band 42 (at room temperature)... 18 Table 1 Summary of Measurement Results of Band 43 (at room temperature)... 18 Table 11 Bill-of-Materials... 19 Application Note AN328, Rev. 1. 5 / 35
Introduction 1 Introduction The mobile technologies for smartphones have seen phenomenal growth in recent times. The data rate of mobile devices has increased significantly over the evolution modern mobile technologies starting from the first 3G/3.5G technologies (UMTS & WCDMA, HSPA & HSPA+) to the 4G LTE. The ability of 4G LTE to support bandwidths up to 2 MHz and to have more spectral efficiency by using better modulation methods like 64QAM, is of particular importance as the demand for higher wireless data speeds continues to grow fast. LTE Advanced can aggregate up to 15 carriers (up to 1 MHz) to increase user data rates and capacity for high speed applications. A block diagram of a typical 2G and 3G/4G modem (GSM/EDGE/UMTS/LTE/TDS- CDMA/TDS-LTE) for smart phone RF front end is shown in Figure 1 below. It consists of a broadband antenna, a band selecting antenna switch, 3G/4G duplexers, high/low band power amplifiers, 3G/4G LNAs and various surface acoustic wave filters. Table 1 shows the band assignment of LTE bands worldwide. ANT Switch ANT Power Detector PA 2G/2.5G Transceiver IC 3G/4G Transceiver IC Duplexer Figure 1 LNA SAW Example of Application Diagram of 2G/3G/4G Front-end System Application Note AN328, Rev. 1. 6 / 35
Introduction In order to cover different countries with a unique device, mobile phones and 3G/4G data cards are usually equipped with more than one band. Some typical examples are the triple band combination of band 1, 2 and 5; 4, 13 and 17 or quad band combination of band 1, 2, 5 and 8. Table 1 LTE Band Assignment Band No. Uplink Frequency (Tx) Downlink Frequency (Rx) Diplex Mode 1 192-198 MHz 211-217 MHz FDD 2 185-191 MHz 193-199 MHz FDD 3 171-1785 MHz 185-188 MHz FDD 4 171-1755 MHz 211-2155 MHz FDD 5 824-849 MHz 869-894 MHz FDD 6 83-84 MHz 875-885 MHz FDD 7 25-257 MHz 262-269 MHz FDD 8 88-915 MHz 925-96 MHz FDD 9 1749.9-1784.9 MHz 1844.9-1879.9 MHz FDD 1 171-177 MHz 211-217 MHz FDD 11 1427.9-1452.9 MHz 1475.9-15.9 MHz FDD 12 698-716 MHz 728-746 MHz FDD 13 777-787 MHz 746-756 MHz FDD 14 788-798 MHz 758-768 MHz FDD 17 74-716 MHz 734-746 MHz FDD 18 815-83 MHz 86-875 MHz FDD 19 83-845 MHz 875-89 MHz FDD 2 832-862 MHz 791-821 MHz FDD 21 1447.9-1462.9 MHz 1495.9-151.9 MHz FDD 22 341-35 MHz 351-36 MHz FDD 23 2-22 MHz 218-22 MHz FDD 24 1626.5-166.5 MHz 1525-1559 MHz FDD 25 185-1915 MHz 193-1995 MHz FDD 26 814-849 MHz 859-894 MHz FDD 27 87-824 MHz 852-869 MHz FDD 28 73-748 MHz 758-83 MHz FDD 33 19-192 MHz TDD 34 21-225 MHz TDD 35 185-191 MHz TDD 36 193-199 MHz TDD 37 191-193 MHz TDD 38 257-262 MHz TDD 39 188-192 MHz TDD 4 23-24 MHz TDD 41 2496-269 MHz TDD 42 34-36 MHz TDD 43 36-38 MHz TDD 44 73-83 MHz Application Note AN328, Rev. 1. 7 / 35
Introduction 1.1 Multiband / Broad-Band LNAs for 3G/3.5G/4G Modems Motivated by increasing demand for mobile broadband services with higher data rates and better quality of service, the modern mobile technology has seen tremendous growth in the recent years from 2G to 3G/3.5G HSPA, HSPA+ 3.9G LTE and now recently 4G LTE advanced. LTE-advanced can support data rates of up to 1 Gbps. Such higher requirements are met by using advanced MIMO techniques and wider bandwidths of up to 1MHz enabled by carrier aggregation. LTE-Advanced can support up to 15 bands of carrier aggregation by three component carrier aggregation scenarios: intra-band contiguous, intraband non-contiguous and inter-band non-contiguous aggregation. This in turn presents new challenges to RF front end designers such as interference from co-existing bands and harmonic generations. In order to address these requirements we need smart LNAs with the following features to achieve outstanding performance. Low Noise Figure: An external LNA boosts the sensitivity of the system by reducing the overall noise figure. In addition due to the size constraint the modem antenna and the receiver front end cannot always be put close to the transceiver IC. The path loss in front of the integrated LNA on the transceiver IC increases the system noise figure significantly. An external LNA physically close to the antenna can help to eliminate the path loss and reduce the system noise figure. Therefore the sensitivity can be improved by several db which means increase in the connectivity range significantly. Recent trend of end users to download more and more data anytime and anywhere increases the need of more bandwidth and an additional receive channel called diversity path in smart phones. In most mobiles phones now, there is more than one antenna to employ diversity. Diversity exploits the radiowave phenomenon of multipath propagation to enhance the reception of cellular signals. The diversity antenna is usually located far from the main antenna and the transceiver IC. The received signal therefore undergoes losses along the path from the diversity switch to the transceiver IC. We need to use an LNA closer to the diversity antenna to overcome this and enhance the sensitivity of the system. The LNAs improve the receiver performance significantly by reducing the noise contribution of long Application Note AN328, Rev. 1. 8 / 35
Introduction route line between diversity antenna and transceiver, losses incurred due to the band pass filter and noise figure of the transceiver. High Linearity: The presence of increased number of bands at the receiver input creates strong interference leading to high requirements in linearity characteristics such as high input compression point, IMD2 & IIP3 performance. Low Power Consumption: Power consumption becomes even more important in today s smart phones. The latest LTE advanced uses enhanced MIMO techniques with upto 8 streams for downlink and 4 streams for uplink. Infineon s LNAs have low supply current and an integrated on / off feature which provides for low power consumption and increased standby time for 3G cellular handsets or other portable, battery-operated wireless applications. High Integration and Simple Control Interface: The demand for size and cost reduction and performance enhancement with easy to use and low parts count has become very important in existing and future generation smartphones. Our MMIC LNAs are highly integrated with Input and output either matched or pre-matched, in-built temperature and supply voltage stabilization and fully ESD protected circuit design to ensure stable operation and a simple control interface. This application note is focusing on the low cost discrete broad-band LNA solution using Infineons new generation RF Transistor BFR843EL3 which has internal RC feedback to cover broad frequency range. Figure 2 shows the modified RF Front-end block diagram using this broad-band LNA solution. Compare to Figure 1 now, for example, four multi-band LNAs can be replaced by only one broad-band LNA. This can reduce cost, PCB area and system complexity. Infineon does also support with RF MMIC LNAs, RF-switches, TVS-diodes for ESD protection and RF Schottky diodes for power detection for 3G/4G LTE applications. Application Note AN328, Rev. 1. 9 / 35
Introduction ANT Switch ANT Power Detector PA 2G/2.5G Transceiver IC Broad-Band LNA 3G/4G Transceiver IC Duplexer Figure 2 Example of Application Diagram of 2G/3G/4G Front-end System using BFR843EL3 Broad- Band LNA SAW Application Note AN328, Rev. 1. 1 / 35
BFR843EL3 Overview 2 BFR843EL3 Overview 2.1 Features Low noise broadband NPN RF transistor based on Infineon s reliable, high volume SiGe:C bipolar technology High maximum RF input power and ESD robustness Unique combination of high RF performance, robustness and ease of use Low noise figure: NF min =.95 db at 7 MHz and 1.1 db at 3.8 GHz, 1.8 V, 8 ma High gain S21 2 = db at 6 MHz and 16.5 db at 3.8 GHz, 1.8 V, 15 ma OIP3 = 22 dbm at 6 MHz and dbm at 3.8 GHz, 1.8 V, 15 ma Ideal for low voltage applications e.g. V CC = 1.2 V and 1.8 V (2.85 V, 3.3 V, 3.6 V requires corresponding collector resistor) Low power consumption, ideal for mobile applications Thin small flat Pb-free (RoHS compliant) and halogen-free package Qualification report according to AEC-Q11 available Figure 3 BFR843EL3 in TSLP-3-9 2.2 Key Applications of BFR843EL3 As Low Noise Amplifier (LNA) in: Wireless Communications: 2.4 GHz Wireless LAN IEEE82.11b/g/n, 5-6 GHz Wireless LAN IEEE82.11a/n/ac, WiMAX, 3G, 3.5G, 4G LTE-Advanced Satellite navigation systems (e.g. GPS, GLONASS, COMPASS...) and satellite C-band LNB (1st and 2nd stage LNA) Broadband amplifiers: Dualband WLAN, multiband mobile phone, UWB up to 1 GHz ISM bands up to 1 GHz Application Note AN328, Rev. 1. 11 / 35
BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications 3 BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications 3.1 Description BFR843EL3 is a discrete SiGe:C hetero-junction bipolar transistor (HBT) designed for high performance broad band Low Noise Amplifier (LNA) solutions for LTE and Wi-Fi connectivity applications. This has been developed using Infineon s latest B9HFM technology. The key features of this technology are very high transition frequency (f T = 8 GHz) and low parasitics, which enable to achieve higher gain and lower noise figure compared to the previous generation RF transistor BFR74L3RH. BFR843EL3 features an integrated on-chip R-C feedback network. The negative feedback reduces the effects of performance variations of the amplifier. The design is therefore less sensitive to variations in PCB layout resulting in an amplifier with broader bandwidth, easier impedance matching and improved stability margin. However the price paid for using negative feedback is slight degradation of noise figure and decrease in gain. The BFR843EL3 is housed in low-height.31mm TSLP-3-9 package specially fitting into modules. It is also available in other packages, e.g. BFP843 in SOT343 and BFP843F in TSFP-4-1 package. The BFR843EL3 has an integrated 1.5 kv HBM ESD protection which makes the device robust against electrostatic discharge and extreme RF input power. The device offers its high performance at low current and voltage and is especially well-suited for portable battery powered applications in which energy efficiency is a key requirement. Figure 4 shows the pin assignment of package of BFR843EL3 in the top view: E 3 B 1 2 C Figure 4 Package and pin connections of BFR843EL3 in Topview Application Note AN328, Rev. 1. 12 / 35
BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications This application note presents the measurement results of the broad-band LTE LNA covering 7 MHz to 38 MHz using BFR843EL3. The application circuit requires 9 passive 21 Surface Mounted Device (SMD) components. It operates with 2.8 Volt and consumes 8 ma biasing current. At 7 MHz band it provides 2.5 db power gain and at Band 43 (36-38 MHz) the power gain is 14 db. The NF varies from.92 db to 1.22 db (SMA and PCB losses are subtracted) over the complete frequency range. The circuit achieves an input and output return loss better than 11 db from 7 MHz to 38 MHz. Furthermore, the circuit is unconditionally stable up to 1 GHz. At 7 MHz, -19.5 dbm input compression point (IP1dB) is achieved, together with the 15 dbm output third intercept point (OIP3) measured with 1MHz tone spacing. At 38 MHz, -13.7 dbm input compression point (IP1dB) is achieved, together with the 14.3 dbm output third intercept point (OIP3) measured with 1MHz tone spacing. However, higher P1dB can be achieved at the cost of higher biasing voltage and current. For example, OP1dB is 4 to 5 dbm higher with 3 volt and 13 ma biasing condition. Application Note AN328, Rev. 1. 13 / 35
BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications 3.2 Performance Overview Device: BFR843EL3 Application: PCB Marking: BFR843EL3 M13129 (designed for 21 SMD) Table 2 Summary of Measurement Results of Band 5, 6, 12, 13, 14, 17, 18, 19, 2, 26, 27, 28, 44 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 73 894 MHz Gain G 2.5 db Noise Figure NF 1.9 db Input Return Loss RL in 12.6 db Output Return Loss RL out 14.1 db Reverse Isolation IRev 25.5 db Input P1dB IP1dB -19.5 dbm Output P1dB OP1dB dbm Input IP3 IIP3-5.4 dbm SMA and PCB losses of.3 db are subtracted Output IP3 OIP3 15.1 dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 86 MHz. Stability measured from 1MHz to 1GHz Application Note AN328, Rev. 1. 14 / 35
BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications Table 3 Summary of Measurement Results of Band 11, 21, 24 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 1475.9-1559 MHz Gain G 19.2 db Noise Figure NF.92 db Input Return Loss RL in 14.3 db Output Return Loss RL out 11.2 db Reverse Isolation IRev 25.5 db Input P1dB IP1dB -16.9 dbm Output P1dB OP1dB 1.3 dbm Input IP3 IIP3-3. dbm SMA and PCB losses of.6 db are subtracted Output IP3 OIP3 16.2 dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 153 MHz. Stability measured from 1MHz to 1GHz Table 4 Summary of Measurement Results of Band 2, 3, 9, 25, 33, 35, 36, 37, 39 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 185-1995 MHz Gain G 18.1 db Noise Figure NF.95 db Input Return Loss RL in 13.3 db Output Return Loss RL out 1.9 db Reverse Isolation IRev 25.8 db Input P1dB IP1dB -16.4 dbm Output P1dB OP1dB.7 dbm Input IP3 IIP3-2.7 dbm SMA and PCB losses of.6 db are subtracted Output IP3 OIP3 15.4 dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 19 MHz. Stability measured from 1MHz to 1GHz Application Note AN328, Rev. 1. 15 / 35
BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications Table 5 Summary of Measurement Results of Band 1, 4, 1 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 211-217 MHz Gain G 17.5 db Noise Figure NF.98 db Input Return Loss RL in 12.9 db Output Return Loss RL out 1.9 db Reverse Isolation IRev 26. db Input P1dB IP1dB -16.4 dbm Output P1dB OP1dB.1 dbm Input IP3 IIP3-2.5 dbm SMA and PCB losses of.7 db are subtracted Output IP3 OIP3 15. dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 214 MHz. Stability measured from 1MHz to 1GHz Table 6 Summary of Measurement Results of Band 23 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 218-22 MHz Gain G 17.3 db Noise Figure NF 1. db Input Return Loss RL in 12.6 db Output Return Loss RL out 1.8 db Reverse Isolation IRev 26.1 db Input P1dB IP1dB -15.9 dbm Output P1dB OP1dB.4 dbm Input IP3 IIP3-2.3 dbm SMA and PCB losses of.7 db are subtracted Output IP3 OIP3 15. dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 219 MHz. Stability measured from 1MHz to 1GHz Application Note AN328, Rev. 1. 16 / 35
BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications Table 7 Summary of Measurement Results of Band 4 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 23-24 MHz Gain G 16.9 db Noise Figure NF 1. db Input Return Loss RL in 12.4 db Output Return Loss RL out 1.9 db Reverse Isolation IRev 26.2 db Input P1dB IP1dB -15.8 dbm Output P1dB OP1dB.1 dbm Input IP3 IIP3-1.4 dbm SMA and PCB losses of.7 db are subtracted Output IP3 OIP3 15.5 dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 235 MHz. Stability measured from 1MHz to 1GHz Table 8 Summary of Measurement Results of Band 7, 38, 41 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 2469-269 MHz Gain G 16.3 db Noise Figure NF 1.1 db Input Return Loss RL in 12.3 db Output Return Loss RL out 11.2 db Reverse Isolation IRev 26.3 db Input P1dB IP1dB -15.5 dbm Output P1dB OP1dB -.2 dbm Input IP3 IIP3-1.4 dbm SMA and PCB losses of.9 db are subtracted Output IP3 OIP3 14.9 dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 262 MHz. Stability measured from 1MHz to 1GHz Application Note AN328, Rev. 1. 17 / 35
BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications Table 9 Summary of Measurement Results of Band 42 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 34-36 MHz Gain G 14.4 db Noise Figure NF 1.13 db Input Return Loss RL in 12. db Output Return Loss RL out 12.2 db Reverse Isolation IRev 26.6 db Input P1dB IP1dB -14.1 dbm Output P1dB OP1dB -.7 dbm Input IP3 IIP3.2 dbm SMA and PCB losses of.12 db are subtracted Output IP3 OIP3 14.6 dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 35 MHz. Stability measured from 1MHz to 1GHz Table 1 Summary of Measurement Results of Band 43 (at room temperature) Parameter Symbol Value Unit Note/Test Condition DC Voltage V CC 2.8 V DC Current I CC 8 ma Frequency Range Freq 36-38 MHz Gain G 14. db Noise Figure NF 1.9 db Input Return Loss RL in 12. db Output Return Loss RL out 12.7 db Reverse Isolation IRev 26.6 db Input P1dB IP1dB -13.7 dbm Output P1dB OP1dB -.7 dbm Input IP3 IIP3.3 dbm SMA and PCB losses of.12 db are subtracted Output IP3 OIP3 14.3 dbm Power @ Input: -3 dbm Stability k > 1 -- *This measurement is done at 37 MHz. Stability measured from 1MHz to 1GHz Application Note AN328, Rev. 1. 18 / 35
3.3 Schematics and Bill-of-Materials BFR843EL3 BFR843EL3 as Broad Band LNA for 7 MHz 3.8 GHz LTE Applications V cc = 2.8 V All passives are 21 case size Inductors: LQP3T Capacitors: various J3 DC Connector I = ~8. ma C3 R2 R1 1 Ω C4 1 nf 39 kω 33 pf J1 RF Port1 INPUT C1 L1 15 nh Q1: BFR843EL3 L2 12 nh R3 1 Ω C2 1 pf J2 RF Port2 OUTPUT 15 pf Total Component Count = 9 PCB = BFR843EL3 M13129 Layer spacing (top RF to internal ground plane):.2 mm Inductors = 2 (LQP3T) Resistors = 3 Capacitors = 4 Figure 5 Schematic Diagram of the Application Circuit Table 11 Bill-of-Materials Symbol Value Unit Size Manufacturer Comment C1 15 pf 21 Various Input DC block & input matching C2 1 pf 21 Various Output DC block & output matching C3 1 nf 21 Various RF decoupling / blocking cap C4 33 pf 21 Various RF decoupling & output matching L1 15 nh 21 LQP3T Input matching & Base biasing L2 12 nh 21 LQP3T Output matching & Collector biasing R1 1 Ω 21 Various R2 39 kω 21 Various DC biasing R3 1 Ω 21 Various Output matching Q1 TSLP-3-9 Infineon Technologies DC biasing (provides DC negative feedback to stabilize DC operating point over temperature variation, transistor hfe variation, etc.) BFR843EL3 SiGe:C Heterojunction Bipolar RF Transistor Application Note AN328, Rev. 1. 19 / 35
Measurement Graphs 4 Measurement Graphs 22 21 2 19 18 17 16 15 14 13 12 153 MHz 19.1 db 86 MHz 2.4 db Insertion Power Gain 19 MHz 18.1 db 214 MHz 17.4 db 262 MHz 16.2 db 35 MHz 14.3 db 37 MHz 14 db 5 1 15 2 25 3 35 4 Frequency (MHz) Figure 6 Power Gain of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3-2 Reverse Isolation -22-24 86 MHz -25.5 db 19 MHz -25.8 db 262 MHz -26.3 db 37 MHz -26.5 db -26-28 153 MHz -25.5 db 214 MHz -26 db 35 MHz -26.6 db -3 5 1 15 2 25 3 35 4 Frequency (MHz) Figure 7 Reverse Isolation of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 Application Note AN328, Rev. 1. 2 / 35
NF(dB) BFR843EL3 Measurement Graphs 2 Noise Figure 1.5 7 MHz 1.221 153 MHz.9168 214 MHz.9776 262 MHz 1.11 37 MHz 1.93 1.5 86 MHz 1.95 19 MHz.9537 35 MHz 1.131 7 14 21 28 35 38 Frequency (MHz) Figure 8 Noise Figure of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 Input Matching -5-1 7 MHz -1.89 db 19 MHz -13.26 db 262 MHz -11.91 db 37 MHz -11.85 db -15 86 MHz -12.36 db 153 MHz -14.15 db 214 MHz -12.67 db 35 MHz -11.62 db -2 5 1 15 2 25 3 35 4 Frequency (MHz) Figure 9 Input Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 Application Note AN328, Rev. 1. 21 / 35
-1..2.4.6.8 2. 3. 4. 5. 1. BFR843EL3 Measurement Graphs Input Matching Smith.8 Swp Max 4MHz 1. 1..6 2..4 3..2 86.1 MHz r 1.662 x -.184479 4. 5. 1. 153 MHz r 1.15761 x -.4285 7 MHz r 1.78868 x.11611 -.2 -.4 37 MHz r.785577 x -.416638 262 MHz r.9913 x -.492267 214 MHz r 1.26 x -.478499-2. -3. -1. -5. -4. -.6 -.8 Swp Min 5MHz Figure 1 Input Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 (Smith Chart) Output Matching -5-1 86 MHz -13.69 db 19 MHz -1.85 db 262 MHz -1.98 db 37 MHz -12.64 db -15 7 MHz -14.63 db 153 MHz -11.6 db 214 MHz -1.86 db 35 MHz -12.16 db -2 5 1 15 2 25 3 35 4 Frequency (MHz) Figure 11 Output Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 Application Note AN328, Rev. 1. 22 / 35
-1..2.4.6.8 2. 3. 4. 5. 1. BFR843EL3 Measurement Graphs Output Matching Smith.8 Swp Max 4MHz 5. 1. 1. 1..6 2..2.4 7 MHz r 1.11981 x.38158 86.1 MHz r 1.3786 x.32511 3. 4. -.2 -.4 37 MHz r.88875 x -.434545 2621 MHz r 1.972 x -.591568 153 MHz r 1.51614 x -.499614 214 MHz r 1.16662 x -.624161-3. -1. -5. -4. -2. -.6 -.8 Swp Min 5MHz Figure 12 Output Matching of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 (Smith Chart) 3 Stability k Factor 2.5 2 1.5 1.5 86 MHz 1.1 2 4 6 8 1 Frequency (MHz) Figure 13 Stability K Factor of the Broad-Band LTE LNA with BFR843EL3 Application Note AN328, Rev. 1. 23 / 35
Gain(dB) BFR843EL3 Measurement Graphs 5 Stability Mu Factor 4 3 Mu2 factor Mu1 factor 2 1 1 21 41 61 81 1 Frequency (MHz) Figure 14 Stability Mu Factor of the Broad-Band LTE LNA with BFR843EL3 25 Input 1dB Compression Point_86MHz 2 15 1-34.9 dbm 2.76 db -19.5 dbm 19.76 db 5-35 -3-25 -2-15 -1 Pin (dbm) Figure 15 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 86 MHz) Application Note AN328, Rev. 1. 24 / 35
Gain(dB) Gain(dB) BFR843EL3 Measurement Graphs 25 Input 1dB Compression Point_153MHz 2 15-35 dbm 19.33 db 1-16.8 dbm 18.33 db 5-35 -3-25 -2-15 -1 Pin (dbm) Figure 16 Input 1dB Compression Point of Broad-Band LTE LNA with BFR843EL3 (Measured at 153 MHz) 25 Input 1dB Compression Point_19MHz 2 15 1-35 dbm 18.22 db -16.4 dbm 17.22 db 5-35 -3-25 -2-15 -1 Pin (dbm) Figure 17 Input Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 19 MHz) Application Note AN328, Rev. 1. 25 / 35
Gain(dB) Gain(dB) BFR843EL3 Measurement Graphs 25 Input 1dB Compression Point_214MHz 2 15 1-35 dbm 17.59 db -16.4 dbm 16.59 db 5-35 -3-25 -2-15 -1 Pin (dbm) Figure 18 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 214 MHz) 25 Input 1dB Compression Point_262MHz 2 15 1-35 dbm 16.36 db -15.4 dbm 15.36 db 5-35 -3-25 -2-15 -1 Pin (dbm) Figure 19 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 262 MHz) Application Note AN328, Rev. 1. 26 / 35
Gain(dB) Gain(dB) BFR843EL3 Measurement Graphs 25 Input 1dB Compression Point_35MHz 2 15 1 5-35 dbm 14.45 db -14.1 dbm 13.45 db -35-3 -25-2 -15-1 Pin (dbm) Figure 2 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 35 MHz) 25 Input 1dB Compression Point_37MHz 2 15 1 5-35 dbm 14.6 db -13.7 dbm 13.6 db -35-3 -25-2 -15-1 Pin (dbm) Figure 21 Input 1dB Compression Point of the Broad-Band LTE LNA with BFR843EL3 (Measured at 37 MHz) Application Note AN328, Rev. 1. 27 / 35
Power (dbm) Power (dbm) BFR843EL3 Measurement Graphs -2 Output 3rd Order Intercept Point_86MHz 86 MHz -9.49 87 MHz -9.46-4 85 MHz -58.7 88 MHz -64.7-6 -8-1 84 85 86 87 88 89 Frequency (MHz) Figure 22 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 86 MHz (LNA input power = -3 dbm) -2 Output 3rd Order Intercept Point_153MHz 153 MHz -1.7 154 MHz -1.7-4 -6 152 MHz -64.6 155 MHz -68.2-8 -1 151 152 153 154 155 156 Frequency (MHz) Figure 23 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 153 MHz (LNA input power = -3 dbm) Application Note AN328, Rev. 1. 28 / 35
Power (dbm) Power (dbm) BFR843EL3 Measurement Graphs Output 3rd Order Intercept Point_19MHz -2 19 MHz -12 191 MHz -11.9-4 -6 1899 MHz -66.8 192 MHz -71.4-8 -1 1898 1899 19 191 192 193 Frequency (MHz) Figure 24 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 19 MHz (LNA input power = -3 dbm) Output 3rd Order Intercept Point_214MHz 214 MHz -12.7 2141 MHz -12.7-2 -4-6 2139 MHz -68.1 2142 MHz -71.4-8 -1 2138 2139 214 2141 2142 2143 Frequency (MHz) Figure 25 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 214 MHz (LNA input power = -3 dbm) Application Note AN328, Rev. 1. 29 / 35
Power (dbm) Power (dbm) BFR843EL3 Measurement Graphs Output 3rd Order Intercept Point_262MHz 262 MHz -13.9 2621 MHz -13.9-2 -4-6 2619 MHz -71.5 2622 MHz -73.9-8 -1 2618 2619 262 2621 2622 2623 Frequency (MHz) Figure 26 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 262 MHz (LNA input power = -3 dbm) -2 Output 3rd Order Intercept Point_35MHz 35 MHz -15.9 351 MHz -15.9-4 -6 3499 MHz -76.9 352 MHz -77-8 -1 3498 3499 35 351 352 353 Frequency (MHz) Figure 27 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 35 MHz (LNA input power = -3 dbm) Application Note AN328, Rev. 1. 3 / 35
Power (dbm) BFR843EL3 Measurement Graphs Output 3rd Order Intercept Point_37MHz 37 MHz -16.1 371 MHz -16.1-2 -4-6 3699 MHz -77 372 MHz -77.7-8 -1 3698 3699 37 371 372 373 Frequency (MHz) Figure 28 Output 3 rd Order Intercept Point of the Broad-Band LTE LNA with BFR843EL3 at 37 MHz (LNA input power = -3 dbm) Application Note AN328, Rev. 1. 31 / 35
5 Evaluation Board and Layout Information BFR843EL3 Evaluation Board and Layout Information Figure 29 Photo Picture of Evaluation Board for 7 38 MHz Broad-Band LTE LNA with BFR843EL3 Figure 3 Zoom-In of Photo Picture Application Note AN328, Rev. 1. 32 / 35
Evaluation Board and Layout Information.2 mm.1mm E BFR843EL3 B C Figure 31 Layout Proposal for RF Grounding of the 7 38 MHz Broad-Band LTE LNA with BFR843EL3 Vias FR4 Core,.2mm Copper 35µm FR4 Prepreg,.8mm Figure 32 PCB Layer Information Application Note AN328, Rev. 1. 33 / 35
Authors 6 Authors Bingqing Dai, Internship Student of Application Engineering of Business Unit RF and Protection Devices Shamsuddin Ahmed, Application Engineer of Business Unit RF and Protection Devices Application Note AN328, Rev. 1. 34 / 35
w w w. i n f i n e o n. c o m Published by Infineon Technologies AG AN328