H Hydraulic Cylinders Heavy Duty NPA for Working Pressures up to 0 bar
Catalogue H07-0/U Mounting Styles H Series H Cylinder Mounting Styles The standard range of Parker H cylinders comprises 7 mounting styles. Dimensional information for each mounting style is shown on pages 0- for 8.mm to 0.mm ( / to 8 ) bore sizes, and on pages -5 for 5mm and 0.8mm (0 and ) bore sizes. Application-specific mounting information is shown on page 0. Where a non-standard mounting style is required, please contact the factory for details. NPA MX NPA MX NPA MX TB TC TD NPA M NPA M5 NPA M5 B NPA M NPA M6 NPA M6 H HB HH NPA MS NPA MS NPA MS7 C NPA MP ISO 698 and NPA MT CTOP P88H BB SBa D NPA MT NPA MT DB DD (TB shown) Most mounting styles are available as double rod cylinders Parker Hannifin urope
Catalogue H07-0/U Piston nd Data 8.mm to 0.mm ( / to 8 ) s Only nd Styles, 7 & 8 All xcept Mount A W V nd Style 9 All xcept Mount W V H Series nd Styles & 8 The standard rod end, Style, is recommended for all applications in which the work piece is secured against the rod shoulder. Where the work piece is not shouldered, Style 8 rod ends are recommended. nd Style 9 or applications where a female thread is required. B NA D Wrench lats MM B NA D Wrench lats A MM nd Style Non-standard piston rod ends are designated Style. A dimensional sketch or description should accompany the order. Please specify dimensions and A. nd Styles, 7 & 8 Mount Only A W nd Style 9 Mount Only W T nd Style 7 Style 7 rod ends apply to rod eyes with spherical bearings only (see pages 7 and 9). The Style 7 rod end with spherical bearing allows the same diameter pivot pin to be used at both the head and cap ends of the cylinder. or Style 7 rod end thread lengths, please refer to dimension A in the table below. D D Style Dimensions which are not shown are identical to those shown for the equivalent non- design. T A nd Dimensions 8.mm to 0.mm ( / to 8 ) bore sizes only 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 MM Diameter 5.9 ( 5 / 8") 5. (") 5. (").9 ( / 8") 5. (").5 ( / ").9 ( / 8").9 ( / 8") (").5 ( / ").5 ( / ") 6.5 ( / ") (") (") 88.9 ( / ") 6.5 ( / ") 76. (") 6.5 ( / ") 0.6 (") 76. (") 88.9 ( / ") 76. (") 7.0 (5") 88.9 ( / ") 0.6 (") 88.9 ( / ") 9.7 (5 / ") 0.6 (") 7.0 (5") Style & 9 Style 8 Style 7 A B +0.00 A -0.05 Metric UN Metric UN Metric M0x.5 M0x.5 M0x.5 M6x.5 M0x.5 Mx M6x.5 M6x.5 M9x Mx Mx M8x M9x M9x M6x M8x M58x M8x M76x M58x M6x M58x M90x M6x M76x M6. M00x M76x M90x 7 / 6-0 / - 6 / - 6 - / - 6 / - - - / - / - / - 7 / 8 - / - / - / - 7 / 8 - / - 7 / 8 - - / - / - / - / - / - - / - - - / - Mx.5 Mx.5 Mx.5 M0x Mx.5 M9x M0x M0x M5x M9x M9x M56x M5x M5x M76x M56x M68x M56x M95x M68x M76x M68x M0x M76x M95x M76x M0x M95x M0x / - 0 7 / 8-7 / 8- / - 7 / 8- / - / - / - / - / - / - / - / - / - / - / - / - / - / - / - / - / - / - / - / - / - 5 / - / - / - M6x.5 M0x.5 M0x.5 M7x M7x Mx Mx Mx Mx M8x M8x M6x M6x 7 5 55 6 8 9.0 8.6 8.6. 8.6.. 57. 76. 57. 57. 88.9 76. 88.9 76. 0.6 88.9 88.9 88.9 7.0 88.9 0.6 88.9 9.7 0.6 7.0 8.55 8.07 8.07 50.77 8.07 60.0 50.77 50.77 66.65 60.0 60.0 7 66.65 66.65 07.9 7 95. 7 0.6 95. 07.9 95. 6.0 07.9 0.6 07.9 58.7 0.6 6.0 D NA V W 0 6 0 0 6 6 55 75 55 65 55 85 65 75 65 0 75 85 75 0 85 0..8.8..8.9.. 9..9.9 60. 9. 9. 85.7 60. 7.0 60. 98. 7.0 85.7 7.0.8 85.7 98. 85.7 6.5 98..8 6..7 6. 6..7 6. 6. 6. 6. 6. 6. 6. 6. 6. 6. 6. 6. 6. 6. 6. 6. 5.9 5. 9. 5. 9..8 5...8 8.6 5..9 8.6 8.6.9.9.9.8.8.8.8.8.8.8.8.8.8.8.8 All rod threads are UN except - which is UNS. Style 7 threads apply to spherical rod eyes only, see pages 7 and 9. Parker Hannifin urope Mount Only D T W max. 5.0 6.5 6.5 76. 6.5 88.9 76. 76. 0.6 88.9 88.9. 0.6 0.6 6.... 65.. 6.. 90.5 6. 65. 6. 09.6 65. 90.5 5.9 5.9 5.9 5.9 5.9 5.9 5.9 5.9 9. 5.9 5.9 5.9 5. 5.9 9. 5.9 9. 9. 5. 5. 5.0 5.0. 5.0 7.7.. 7.7 7.7 57. 57. 57. 57. 57. 57. 57. 57. 57. 57. 57. 57. 57. 57. 57. 57.
Catalogue H07-0/U Storage and Installation, Cylinder Masses H Series Storage When cylinders must be stored for a period of time, the following procedures are recommended:. Store the cylinders in an indoor area which has a dry, clean and non-corrosive atmosphere. Take care to protect the cylinder from both internal corrosion and external damage.. Whenever possible, cylinders should be stored in a vertical position (piston rod up). This will minimize corrosion due to possible condensation which could occur inside the cylinder.. Port protector plugs should be left in the cylinder until the time of installation. Installation. Cleanliness is an important consideration, and Parker cylinders are shipped with the ports plugged to protect them from contaminants entering the ports. These plugs should not be removed until the piping is to be installed. Before making the connection to the cylinder ports, piping should be thoroughly cleaned to remove all debris which might have resulted from threading or flaring operations.. Cylinders operating in an environment where air drying materials are present such as fast-drying chemicals, paint, or weld splatter, or other hazardous conditions such as excessive heat, should have shields installed to prevent damage to the piston rod and piston rod seals.. Correct alignment of the cylinder piston rod and its mating component on the machine should be checked in both the extended and retracted positions. Incorrect alignment will result in excessive rod gland and/or cylinder bore wear, shortening the life of the cylinder. Masses Series H Cylinders To determine the mass of the cylinder, first select the basic mass for zero stroke, then calculate and add the mass for the appropriate stroke length. Masses for accessories are shown on pages 7 to 9. 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5.0 (0") 0.8 (") 5 Single Cylinders Mass at Zero Stroke Mounting Styles TB, TC, TD,, B, H, HB, kg.6.7 5.7 6.0 7.9 8.7 8. 5. 6. 5.7 0.. 0.8 6 7 9 58 6 60 6 97 88 90 0 5 0 75 9 7, HH, D, DB, DD, C,, SBa, BB kg.7.9 7.5 7.8 0..0 0.8 9. 0. 9.9 5.7 7.5 6 9 6 7 7 77 7 75 05 6 07 09 5 60 8 55 8 57 557 Mass per 0mm Stroke kg 0.09 0. 0. 0.8 0.9 0.7 0. 0. 0.9 0.6 0.9 0.5 0. 0.59 0.9 0.68 0.79 0.9.....8...6..8..0.0.9 5.6 Double Cylinders Mass at Zero Stroke Mounting Styles TB, TD,, B, kg.. 6.9 7.5 9..0 0.0 8. 0.0 9. 5 9 6 5 6 9 68 80 7 7 99 0 08 7 66 57 5 57 59 579, C,, D, DD kg 5. 5.5 8.7 9..7..7.5..5 5 5 6 55 58 8 9 85 88 9 8 6 9 68 8 78 0 60 66 Mass per 0mm Stroke kg 0.0 0.5 0.8 0.5 0. 0.9 0.0 0.9 0.55 0.8 0.5 0.76 0.58 0.75.0 0.9.0..0..7.5.8.8...5...0 5.9 5. 8. Warning AILU O IMPOP SLCTION O IMPOP US O TH PODUCTS AND/O SSTMS DSCIBD HIN O LATD ITMS CAN CAUS DATH, PSONAL INU AND POPT DAMA. This document and other information from Parker Hannifin Corporation, its subsidiaries, sales offices and authorized distributors provide product or system options for further investigation by users having technical expertise. Before you select or use any product or system it is important that you analyse all aspects of your application and review the information concerning the product or system in the current product catalogue. Due to the variety of operating conditions and applications for these products or systems, the user, through his own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance and safety requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale Please contact your local Parker representative for a detailed offer of sale. Parker Hannifin urope
Catalogue H07-0/U Introduction Parker Offers the Widest ange of Industrial Cylinders High Productivity Low Cost of Ownership Parker Hannifin's is the world's largest supplier of hydraulic cylinders for industrial applications. Parker manufactures a vast range of standard and special tie rod, roundline and 'mill' type cylinders to suit all types of industrial cylinder applications. Our cylinders are available to ISO, DIN, NPA, ANSI and IC standards, with other certifications available on request. All Parker hydraulic cylinders are designed to deliver long, efficient service with low maintenance requirements, guaranteeing high productivity year after year. About Parker Hannifin Parker Hannifin is the global leader in motion and control technologies, partnering with its customers to increase their productivity and profitability. The company employs more than 5,000 people in 8 countries around the world, providing customers with technical excellence and first class customer service. Visit us at www.parker.com H Series Contents Page Mounting Styles, 9 Piston nd Data 8.mm to 0.mm ( / " to 8") bores Storage Information and Mass Data Standard Specifications 5 Design eatures and Benefits 6 Optional eatures 8 Mounting Dimensions 8.mm to 0.mm ( / " to 8") bores 0 5.0mm to 0.8mm (0" and ") bores Double Cylinders 6 Accessories 7 Mounting Information 0 Push and Pull orces Pressure Limitations Piston Sizes and Stroke actors Stop Tubes & Long Stroke Cylinders Ports, Locations and Piston Speeds 5 Cushioning 6 Seals and luids 7 eplacement Parts and Service 8 epairs 9 Piston nd Data 5.0mm and 0.8mm (0" and ") bores 0 How to Order Cylinders The H Cylinder ange The H cylinders described in this catalogue are heavy duty hydraulic cylinders rated for use at working pressures up to 0 bar depending on the rod end and type of service. In addition to the standard cylinders featured in this catalogue, H cylinders can be designed to suit customer requirements. Our engineers will be pleased to advise on unique designs to suit specific applications. Standard Specifications Heavy-duty service ANSI B-987 and NPA specifications Standard construction square end, tie rod design Standard pressure 0 bar Standard fluid hydraulic mineral oil Standard temperature -0 C to 80 C (- to 76 ) inphorm and -D CAD Parker offers easy-to-use software to simplify the cylinder selection process, saving your time and ensuring the accuracy of designs and drawings. InPHorm selection software and new -D CAD modelling software can be downloaded from our urope website. Please visit us at www.parker.com or contact your local Sales Office for more information. sizes 8.mm ( / ) to 0.8mm ( ) Piston rod diameters 5.9mm ( 5 / 8 ) to 5.9mm (8 / ) Mounting styles 7 standard styles Strokes available in any practical stroke length Cushions optional at either end or both ends of stroke ends three standard choices, specials to order 5 Parker Hannifin urope
Catalogue H07-0/U Design eatures and Benefits H Series 5 6 0 8 Piston land seal life is maximised by manufacturing piston rods from precision ground, high tensile carbon alloy steel, hard chrome plated and polished to 0.µm max. Piston rods are induction case hardened to ockwell C5 minimum before chrome plating, resulting in a dent-resistant surface. Parker s land Continuous lubrication, and therefore longer gland life, are provided by the long bearing surface inboard of the lipseal. The gland, complete with rod seals, can easily be removed without dismantling the cylinder, so servicing is quicker and therefore more economical. Seals The serrated lipseal has a series of sealing edges which take over successively as pressure increases, providing efficient sealing under all operating conditions. On the return stroke the serrations act as a check valve, allowing the oil adhering to the rod to pass back into the cylinder. The double lip wiperseal acts as a secondary seal, trapping excess lubricating film in the chamber between the wiper and lip seals and preventing the ingress of dirt into the cylinder, extending the life of gland and seals. Standard lipseals are manufactured from an enhanced polyurethane, giving efficient retention of 7 9 & 0 9 fluid and a life of up to five times that of traditional seal materials. Standard rod seals are suitable for speeds up to 0.5m/s special seal combinations are available for higher speed applications. Cylinder Body Strict quality control standards and precision manufacture ensure that all tubes meet rigid standards of straightness, roundness and surface finish. The steel tubing is surface finished to minimise internal friction and prolong seal life. 5 Cylinder Body Seals To ensure that the cylinder body remains leak free, even under pressure shock conditions, Parker fits pressure-energised body seals. 6 Piston All pistons are of one-piece type, and feature wide bearing surfaces to resist side loading. Long thread engagement secures the piston to the piston rod and, for additional safety, the piston is secured by thread-locking adhesive and a locking pin. 7 Piston Seals Cast Iron Piston ings are extremely durable but allow some leakage across the piston and cannot therefore hold a load in position. Cast iron piston rings are fitted as standard on series H hydraulic cylinders. Lipseal Pistons can hold a load in position, but are not as durable as pistons with cast iron rings or Hi-Load seals. or applications with a working pressure in excess of 0 bar where the duty cycle requires sustained piston speeds in excess of 0.m/s or high cycling performance, other seal options should also be considered. Where these performance criteria may be exceeded, please contact the factory with details of the application. Hi-Load Pistons resist side loading and are recommended for long stroke cylinders, especially when pivot mounted. Special wear rings prevent metal-to-metal contact between the piston and tube and thereby extend the life of the cylinder. Low riction Seals are also available see page 7. 6 Parker Hannifin urope
Catalogue H07-0/U eatures and Benefits 8 Ports High piston speeds allow rapid cycling, which maximises machine productivity. Parker offers a range of port sizes to permit different flow rates, in all common inch and metric standards. Choosing the correct port size simplifies design and installation, and cuts maintenance time to a minimum. 9 Cushioning Progressive deceleration reduces both noise and shock, prolonging machine life and improving the working environment. Parker H cylinders are available with stepped cushions at the head and cap, which decelerate a load safely while optimising the cycling rate of the process. The head and cap end cushions are self-centring. The polished cap end spear is an integral part of the piston rod. H Series Seal Classes To accommodate the many types of fluid and the varying temperature ranges used in industry, Parker offers a range of rod gland, piston and body seals moulded in different profiles and from different materials. These are described in detail on page 7. Special Designs Parker s design and engineering staff are available to produce special designs to meet customer s specific requirements. Alternative sealing arrangements, special mounting styles, different bores and rod sizes are just a few of the custom features which can be supplied. 0 loating Cushion Bushes & Sleeves Closer tolerances and therefore more effective cushioning are permitted by the use of a floating cushion sleeve at the head end of the cylinder, and a floating cushion bush at the cap end. A specially designed cushion sleeve on bore sizes up to 0.6mm ( ) operates as a check valve. On larger bore sizes a conventional ball check valve is used. The use of a check valve in the head and lifting of the bronze cushion bush in the cap, provides minimum fluid flow restriction at the start of the return stroke. This allows full pressure to be applied over the whole area of the piston, to provide full power and fast cycle times. Cushion Adjustment Needle valves are provided at both ends of the cylinder for precise cushion adjustment, and retained within the head and cap so that they cannot be inadvertently removed. The cartridge type needle valve illustrated is fitted to cylinders of up to 6.5mm ( / ) bore. See page 5 for location. Tie Construction Tie rod construction, with tie rods torque-loaded on assembly, imposes a compressive force on the cylinder tube which counters the tensile forces generated by system pressure. The result a fatigue-free cylinder with long service life and exceptionally compact dimensions. 7 Parker Hannifin urope
Catalogue H07-0/U Optional eatures Air Bleeds The option of air bleeds is available at either or both ends of the cylinder, at any position except in the port face see page 5 for location. To ensure operator safety, the standard M8 air bleed screw (illustrated) is recessed into the head and cap and retained so that it cannot be inadvertently removed. land Drains The accumulation of fluid between the gland seals of long stroke cylinders, cylinders with constant back pressure or where the ratio of the extend speed to the retract speed is greater than to, can be relieved by specifying an optional gland drain. A transparent tube fitted between the gland drain and the reservoir allows fluid loss from concealed or inaccessible cylinders to be monitored, giving an early indication of the need for gland servicing. A / 8 NPT gland drain port can be provided in the retainer on all cylinders up to and including 0.mm (8 ) bore sizes, except 8.mm ( / ) with no. rod. or 8.mm ( / ) bore cylinders with no. rod, the retainer thickness is increased to 5.9mm ( 5 / 8 ). or 8.mm ( / ) bore cylinders with no. rod, the drain port is located in the head end adjacent to the port. Stroke Limiters Where absolute precision in stroke length is required, a screwed adjustable stop can be supplied at the cap end. Several types are available the illustration shows a design suitable for infrequent adjustment of an uncushioned cylinder. Please contact the factory, specifying details of the application and the adjustment required. L Seal Wrench Square H Series Locking Devices These units provide positive locking of the piston rod. They require hydraulic pressure to release, while loss of pressure causes the clamp to operate, allowing them to be used as a failsafe device. Please consult the factory for further information. Single-Acting Cylinders Standard H series cylinders are of the double-acting type. They are also suitable for use as single-acting cylinders, where the load or other external force is used to return the piston after the pressure stroke. Cast iron piston rings should not be used with single-acting cylinders. Spring-eturned, Single-Acting Cylinders Single-acting cylinders can be supplied with an internal spring to return the piston after the pressure stroke. Please supply details of load conditions and friction factors, and advise whether the spring is required to advance or return the piston rod. On spring-returned cylinders, it is recommended that tie rod extensions be specified to allow the spring to be backed off until compression is relieved. Please consult the factory when ordering spring-returned cylinders. Multiple Stroke Positioning To obtain linear force in one plane with controlled stopping at intermediate points, several designs are available. or three stopped positions, it is common practice to mount two standard single rod Style H cylinders back-to-back, or to use through-tie rods. By extending or retracting the stroke of each cylinder independently, it is possible to achieve three positions at the piston ends. An alternative technique is to use a tandem cylinder with an independent piston rod in the cap section. Please consult the factory for further details. nd Bellows Unprotected piston rod surfaces which are exposed to contaminants with air hardening properties should be protected by rod end bellows. Longer rod extensions are required to accommodate the collapsed length of the bellows. Please consult the factory for further information. Metallic Wipers Metallic rod wipers replace the standard wiper seal, and are recommended where dust, ice or splashings might damage the wiper seal material. They do not affect cylinder dimensions. 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") min. L max. 55 7.0 7 75 0. 7 75 8.6 85 8.6 70 57. 70 508.0 75 508.0 50 75 508.0 60 80 508.0 DC Proximity Sensors These can be fitted to give precise, repeatable end of stroke signals. Please contact the factory for details. Position eedback Linear position transducers of various types are available for H series cylinders. Please contact the factory for details. 8 Parker Hannifin urope
Catalogue H07-0/U Mounting Styles H Series Mounting Styles and Where to Use Them See also application-specific mounting information on page 0. xtended Tie Mountings Styles TB, TC and TD Application straight line force transfer compression (push) use cap end mountings TC or TD tension (pull) use head end mountings TB or TD Benefits ease of mounting where space is limited high efficiency force is absorbed on cylinder's centreline TD double-ended mounting allows brackets or switches to be attached to cylinder Styles TB, TC, TD See pages 0- TB lange Mountings Styles, B,, H, HB and HH Application straight line force transfer compression (push) use cap end mounting H, HB or HH tension (pull) use head end mounting, B or Benefits exceptionally rigid mounting due to large flange area high efficiency force is absorbed on cylinder's centreline oot Mountings Style C,, Application straight line force transfer suitable for push or pull applications force is not absorbed on centreline secure attachment, eg: a thrust key (page 0) and effective load guidance are vital Benefits ease of mounting and adjustment Pivot Mountings Styles BB and SBa Application curved path force transfer movement in a single plane use fixed clevis style BB movement in more than one plane use spherical bearing style SBd Benefits ease of attachment use with plain or spherical bearing at rod end greater flexibility for the machine designer self-alignment resists wear of cylinder's bearing surfaces Trunnion Mountings Styles D, DB and DD Application curved path force transfer movement in a single plane compression (push) use DB or DD mountings tension (pull) use D or DD mountings Benefits greater flexibility for the machine designer self-alignment resists wear of cylinder's bearing surfaces high efficiency force is absorbed on cylinder's centreline ease of attachment use with pivot mounting at rod end Styles, B,, H, HB, HH See pages -5, - Styles C,, See pages 6-7 and 5 Styles BB, SBa See pages 8-9 and 5 Styles D, DB, DD See pages 0- and HH C BB DB 9 Parker Hannifin urope
Catalogue H07-0/U Tie Mountings 8. - 0.mm bores H Series ZB + stroke Z + stroke AA DD Style TB Tie s xtended Head nd (NPA Style MX) BB LB + stroke See Notes, ZB + stroke Z + stroke AA DD Style TC Tie s xtended Cap nd (NPA Style MX) LB + stroke BB See Notes, Dimensions TB, TC & TD See also rod end dimensions, page & mounting information, page 0 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 AA BB DD (BSPP) 58..9 / 8-6.5 /.5 8. 7.7 6.0 / - 0 76. / 5.9.5 8. 9. 6.0 / - 0 88.9 / 5.9.5 8. 6.8 58.7 5 / 8-8. / 9..5 7. 58.7 5 / 8-8 7.0 /..5 77.8 8.0 7 / 8-65. /..5 05.7 9. - 90.5 5. 57. 57. 6. 0.8 / 8-5.9 / 5. 69.9 69.9 69.. / -. / 5. 76. 76. 0 Parker Hannifin urope
Catalogue H07-0/U Tie Mountings 8. - 0.mm bores H Series ZB + stroke Z + stroke AA DD DD Style TD Tie s xtended Both nds (NPA Style MX) BB LB + stroke BB See Notes, Notes All tie rod threads (dimension DD) are UN, with the exception of - which is UNS Mounting nuts should be tightened to the torque values shown for tie rod nuts see page 0 Dimensions TB, TC & TD Continued 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 max 0. 5. 6.8 6 8.6 6 97.0 9 5.7 9 59 59 65 59 7 65 68 79 76 76 79 79 + Stroke LB P ZB max Z 7.0 75. 75 6.5 78 58.8 90 68. 97 8.0 0 5. 6.9 6.5 69.9 66.7 79. 7. 95. 0.8 0.6 08.0 7.5. 0. 6.5 6.5 6.5 Parker Hannifin urope.9 5. 5. 58.8 56.6 68. 6.9 8.0 90.5 87. 9.7 0. 96.9 5.5.7 0 66.7.5 6 67. 9. 6 98.5 7.0 09.6 5.9 5.9 5.9 8 90.5 9 66.7 68 5. 98.
Catalogue H07-0/U Head lange Mountings 8. - 0.mm bores H Series ZB + stroke U Style Head ectangular lange (NPA Style M) LB + stroke T B ( holes) See Note ZB + stroke U U T Style B Head Square lange (NPA Style M5) LB + stroke T B (8 holes) Dimensions, B & See also rod end dimensions, page & mounting information, page 0 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 (BSPP) B B 6.5 /..5 8. 0 0.0. 76. / 5.9..5 8. 88.9 / 5.9..5 8.. / 9. 7.5.5 6 7.0 /. 7.5.5 6 65. /..8.5 9 90.5 5. 7.0 57. 57. 5.9 / 5. 0. 69.9 69.9. / 5.. 76. 76. 7 0.0 6. 0.0 6. 6. 6.. 6. 6. 6.. Parker Hannifin urope. 6. 6. 6. 6. 6. 6. 6. 6. 0.0 6. 6. 6. 6. 6. 0.0 5. 6.8 8.6 97.0 5.7 5.5 67. 90.5
Catalogue H07-0/U Head lange Mountings 8. - 0.mm bores H Series B ZB + stroke L + stroke U D Style ectangular Head (NPA Style M5) T T B ( holes) Notes or maximum pressure ratings in push applications, see page Dimensions, B & Continued D max T T U + Stroke LB L P ZB max 8. ( / ") (") 6.5 ( / ") 5.0 6.5 6.5 76. 6.5 88.9 76. 87. 08.0 0.8 0. 7.5.9 9 59 59 65 59 7 65 7.0 7.5 75. 7.5 75 6.5 0.7 78 5. 6.9 6.5 69.9 66.7 79. 7. 8.6 ( / ") 76. 0.6 88.9 5.9 9. 8.0 68 79 76 58.8 9.7 90 95. 0.8 0.6 0.6 (") 88.9. 0.6 5.9 5.9 6.9 9.7 76 79 68. 6. 97 08.0 7.5. 7.0 (5") 0.6 6... 5.9 5.9 5.9 5.9 08.0 7.7 79 8.0 58.8 0 0. 6.5 6.5 6.5 5. (6"). 65.. 6. 5.9 9. 5.9 5.9 9.7 85.8.7 87. 0 66.7 77.8 (7"). 90.5 6. 65. 5.9 5. 5.9 9. 69.9 0.7 9. 5.9 6 98.5 0. (8") 5 6. 09.6 65. 90.5 5.9 9. 9. 5. 00.0 55.6 9 66.7. 68 5. Parker Hannifin urope
Catalogue H07-0/U Cap lange Mountings 8. - 0.mm bores H Series U Z + stroke Style H Cap ectangular lange (NPA Style M) B ( holes) T LB + stroke X + stroke See Note U Z + stroke U T Style HB Cap Square lange (NPA Style M6) B (8 holes) T LB + stroke X + stroke Dimensions H, HB & HH See also rod end dimensions, page & mounting information, page 0 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 (BSPP) B 6.5 /..5 8. 0. 76. / 5.9..5 8. 5. 88.9 / 5.9..5 8. 6.8. / 9. 7.5.5 6 8.6 7.0 /. 7.5.5 6 97.0 65. /..8.5 9 5.7 90.5 5. 7.0 57. 57. 5.5 5.9 / 5. 0. 69.9 69.9 67.. / 5.. 76. 76. 7 90.5 Parker Hannifin urope
Catalogue H07-0/U Cap lange Mountings 8. - 0.mm bores H Series U LB + stroke Style HH ectangular Cap (NPA Style M6) B ( holes) T X + stroke Notes or maximum pressure ratings in pull applications, see page 0 Dimensions H, HB & HH Continued 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 T U 87. 08.0 0.8 0. 7.5.9 9. 8.0 6.9 9.7 08.0 7.7 9 59 59 65 59 7 65 68 79 76 76 79 79 + Stroke LB P X Z 7.0 75. 75 6.5 78 58.8 90 68. 97 8.0 0.9 5. 5. 58.8 56.6 68. 6.9 8.0 90.5 87. 9.7 0. 96.9 09.6 5.9 5.9 5.9 5 Parker Hannifin urope 5. 6.9 68. 7.6 7.5 8. 77.8 00.0 09.6 06. 9.7 85.8.7 0.5 69.9 69.9 0.7 9. 6 7.0 98.5 00.0 55.6 9 66.7 68 98.5.9 5.9 5. 9..8 8. 8. 8.
Catalogue H07-0/U oot Mountings 8. - 0.mm bores H Series ZB + stroke LB + stroke See Notes,, SB ( holes) ST -0.5 / -0.0 Style C Side Lug Mounting (NPA Style MS) XS SS + stroke SW TS US SW ZB + stroke See Notes, LB + stroke -0.5 / -0.0 Style Side Tapped Mounting (NPA Style MS) XT SN + stroke TN NT thread, ND deep ( mounting holes) Dimensions C, & See also rod end dimensions, page & mounting information, page 0 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 B (BSPP) L O S T ND NT SB ST 6.5.5 /..5 8. 0 76.. /.8.7 5.9.5 8. 88.9. /.8.7 5.9.5 8.. 7.5 / 8.6 5.9 9..5 6 7.0 7.5 / 8.6 5.9 9..5 6 65..8 / 8. 9. 8 8..5 9 90.5 7.0.9. 5 5 5. 57. 57. 5.9 0. / 6.0 5. 50 8 5. 69.9 69.9.. / 8.6 50 8 5. 76. 76. 7 5 7 5 7 5 8 5 8 8 8 5 8 5 57 8 57 M0..7 M 5. 9. M6 6.8 5. M0 8.6 5. M 97.0 6.8 M 5.7 6.8 M0 5.5 8. M 67. 9.5 M 90.5 9.5 6 Parker Hannifin urope
Catalogue H07-0/U oot Mountings 8. - 0.mm bores H Series Z + stroke X + stroke LB + stroke / -0.5-0.0 T Style Side nd Lug (NPA Style MS7) O L L S + stroke O S S 0. - 0. B ( holes) See Note Notes Consider the use of a thrust key with this mounting see page 0 Tapped mounting holes are metric (coarse pitch series) Upper surfaces of lugs are machined for socket head screws Style C cylinders can be supplied with the cylinder ports arranged for mounting and sealing to a manifold surface see page Dimensions C, & Continued 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 SW TN TS US XS XT 8.0 8.6 0.6.7.8 0.6 7.0 7.5.0.8 58.8 7.5 8. 9. 8.. 5. 7.5 5.9. 7.6 09.6 5.0.9.5 7.6 5.0 5. 65. 58.7 58.7 68. 65. 69.9 79. 7.0 7.0 79. 79. 79. 60. 60. 66.7 60. 7.0 66.7 69.9 79. 76. 76. 85.7 79. 79. 85.7 85.7 85.7 9 59 59 65 59 7 65 68 79 76 76 79 79 + Stroke LB P S SN SS X ZB max Z 7.0 75 7.5 7.0 98.. 75 8.0 7.0 9. 6.5 78 8. 76. 85.7 58.8 90 5.9 88.9 0.8 68. 97 5. 95. 0.6 8.0 0 57. 08.0. 65. 7.6 76. 8.6 79. 9. 85.7 09.6 9. 5.9..8 5. 7.7 5.0 5.0 5.0 5. 6.9 6.5 69.9 66.7 79. 7. 95. 0.8 0.6 08.0 7.5. 0. 6.5 6.5 6.5 7.6 8. 88.9 95. 9. 0.8 98. 5. 5.0.8 8. 7.7. 8.6 8. 7.7 0.8 85.7 88.9.7 0 98.5 0. 0. 87. 66.7 09.6.9 90.0 85.8 55.6 9. 96.8 9. 6. 9. 6. 9. 98.5.5.9 05.0. 8.0 9. 00.0 9 66.7 68 68. 68. 7.5 9. 5. 77.8 66.7 7. 7. 7. 7 Parker Hannifin urope
Catalogue H07-0/U Pivot Mountings 8. - 0.mm bores H Series ZC + stroke CD M Style BB Cap ixed Clevis (NPA Style MP) CW CB CW XC + stroke L See Note º LB + stroke MS º CN Style SBa Spherical Bearing (ISO 698 and CTOP P88H) X P XO + stroke XV + stroke LS See Notes,,, 5 Dimensions BB & SBa See also rod end dimensions, page & mounting information, page 0 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 CB CD +0.00-0.05 CN H7 CW (BSPP) max P X 9.8.7 0.7 6.5 / 5 0 8.5 8..5 9.08 5 5.9 76. / 5 5.9.5 8..5 9.08 5.9 88.9 / 8 8 5.9.5 8. 8.9 5. 0 9.. / 9 0 5 9..5 5.6.95 50 5. 7.0 / 59 50 0..5 65.0.8 6.8 65. / 7 6 5..5 65.0 80.8 90.5 90 80 60 5. 57. 57. 77.8 6.5 8. 5.9 / 5. 69.9 69.9 77.8 76. 8.. / 5. 76. 76. 8 Parker Hannifin urope
Catalogue H07-0/U Pivot Mountings 8. - 0.mm bores H Series Notes Supplied complete with pivot pin Maximum pressure rating 60 bar or matching pin sizes specify rod end Style 7, see pages and 9 Pivot pin not supplied 5 or spherical bearing mountings on cylinders above 5.mm (6 ) bore, please consult the factory Dimensions BB & SBa Continued 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 L LS M MS max 0. 5.9 5 5. 6.8.8.8 8 6.8 0. 50 6.5 50. 6 9 5. 6 5.0 7 9 59 59 65 59 7 65 68 79 76 76 79 79 + Stroke LB P XC XO 5 XV ZC 7.0 75. 75 6.5 78 58.8 90 68. 97 8.0 0 6.9 7.5 8. 90.5 87. 00.0 9.7 9. 8.6 5. 7.7 57. 66.7 7. 7. 7. 58.7 78 60. 9.7 0 08.0 8.5 8.5 88.8 7. 0.8 0.6 7. 66. 59.9 8.9 8.9 58. 58..5 7.5 5.8 97. 90.8 7.6.. 79.9.9.9 58. 58. 69.9 7.0 9. 6 9.. 7 8.6 79. 9 66.7 68 8.0 60. 77.8 87. 08.0...8 7.5 9. 58.8 55.6 89.0 98. 9. 0.7 7. 7. 7. 68. 9 Parker Hannifin urope
Catalogue H07-0/U Trunnion Mountings 8. - 0.mm bores H Series ZB + stroke LB + stroke UT. TD Style D Head Trunnion (NPA Style MT) X TL TL ZB + stroke LB + stroke UT. TD Style DB Cap Trunnion (NPA Style MT) X + stroke TL TL Dimensions D, DB & DD See also rod end dimensions, page & mounting information, page 0 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 BD (BSPP) TD +0.00-0.0 0 Parker Hannifin urope TL TM T.8 6.5 /.5 8. 0 5.0 5. 76. 69.9 8. 76. / 5.9.5 8..9.9 88.9 8.6 8. 88.9 / 5.9.5 8..9.9 0.6 95.. / 9..5 6.5.5 7.0 0.7 7.0 /..5 6.5.5 9.7. 65. /..5 9.5.5 77.8 7.5 76. 90.5 5. 57. 57. 5.9 96.9 76. 5.9 / 5. 69.9 69.9 6.5 6.5 7.7. 88.9. / 5. 76. 76. 7 76. 76. 79. 7.7
Catalogue H07-0/U Trunnion Mountings 8. - 0.mm bores H Series ZB + stroke LB + stroke BD UM See Notes,,. T TD UW Style DD Intermediate ixed Trunnion (NPA Style MT) XI TL TM TL Notes Note the minimum strokes from the table below XI dimension to be specified by customer, note minimum dimension A one-piece trunnion is fitted to 8.mm ( / "), mm (") and 6.5mm ( / ") bore cylinders Dimensions D, DB & DD Continued 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5 UM UT UW X 7.0. 58.8 6. 7.5 58.8 5.9 0. 7.5 8.6 5.9 8. 66.7 5.0 8.6 7.6 57. 57. 6.5 57. 69.9 6.5 66.7 76. 7.0 7.0 8.6 76. 76. 8.6 8.6 8.6 Min. XI 85.7 95. 98. 0.8 98.. 0.8 7.5 7.0.8.8. 7.0 7.0... 9 59 59 65 59 7 65 68 79 76 76 79 79 Style DD min stroke + Stroke LB P X ZB max 0.0 7.0 75.. 75 0.0 6.5 78 6. 58.8 90 0.0 68. 97 0.0 8.0 0.8.. 9.7 6.5 9..9 58.8 68. 65. 7.5 8.0 7.6 87. 9.7 9.7 9.7 5. 6.9 6.5 69.9 66.7 79. 7. 95. 0.8 0.6 08.0 7.5. 7.5 9. 60. 85.7 5...7 0.7 66.7 7.7.9 9. 9. 65. 9 0.0. 6 8. 98.5.8 9.7.9 95. 77.8 9 0.0 66.7 68 60. 5. 0. 6.5 6.5 6.5 Parker Hannifin urope
Catalogue H07-0/U Head lange Mountings 5.0-0.8mm bores H Series ZB + stroke U. max Style Head ectangular lange (NPA Style M) L + stroke T B ( holes) See Notes,,, ZB + stroke U. max U T Style B Head Square lange (NPA Style M5) L + stroke T B (8 holes) See Notes,, ZB + stroke L + stroke U See Notes,, Style ectangular Head (NPA Style M5) T T. max B ( holes) Dimensions, B & See also rod end dimensions, page 0 & mounting information, page 0 (BSPP) B T T U + Stroke L P ZB max 5.0 (0") 0.7.9 6.0 9.7 9.7 9. 5. 8.6 0. 8.6 0.7 7.0 08.0 5.9. 8.6 0.8 (") 77.8 / 9. 5..7.7 See note 90.8. 8.6 69.9 558.8 6.5.9 68. 57. 9. 55.6 Notes The dimensional drawings above show 5mm (0 ) bore models fitted with four tie rods, but can also be used to determine dimensions for 0.8mm ( ) bore models fitted with 6 tie rods Tie rod nuts are flush with cap on 0.8mm ( ) cylinders or maximum pressure ratings, see page lange ports to ISO 66 are also available see page 5 Parker Hannifin urope
Catalogue H07-0/U Cap lange Mountings 5.0-0.8mm bores H Series. max Z + stroke Style H Cap ectangular lange (NPA Style M) B ( holes) T U L + stroke X + stroke See Notes,,,. max U Z + stroke U T Style HB Cap Square lange (NPA Style M6) B (8 holes) T L + stroke X + stroke See Notes,,. max U L + stroke Style HH ectangular Cap (NPA Style M6) B ( holes) T X + stroke See Notes,, Dimensions H, HB & HH See also rod end dimensions, page 0 & mounting information, page 0 (BSPP) B T U + Stroke L P X Z 5.0 (0") 0.7.9 6.0 9.7 9.7 9. 0. 8.6 0.7 7.0 08.0 5.9 8.6 88.9 5.5.8 0.8 (") 77.8 / 9. 5..7.7 See note 90.8 69.9 558.8 6.5.9 68. 57. 9. 55.6 98.5 Notes The dimensional drawings above show 5mm (0 ) bore models fitted with four tie rods, but can also be used to determine dimensions for 0.8mm ( ) bore models fitted with 6 tie rods Tie rod nuts are flush with head on 0.8mm ( ) cylinders or maximum pressure ratings, see page lange ports to ISO 66 are also available see page 5 Parker Hannifin urope
Catalogue H07-0/U Trunnion Mountings 5.0-0.8mm bores H Series ZB + stroke L + stroke UT. TD Style D Head Trunnion (NPA Style MT) X TL TL. max See Notes,, ZB + stroke L + stroke UT. TD Style DB Cap Trunnion (NPA Style MT) X + stroke TL TL. max See Notes,, ZB + stroke L + stroke BD UM See Notes,,,. T UW TD Style DD Intermediate ixed Trunnion (NPA Style MT) XI TL TM TL. max Dimensions D, DB, & DD See also rod end dimensions, page 0 & mounting information, page 0 BD & TD +0.000 (BSPP) -0.05 TL TM T UM UT UW Min. XI X & + Stroke L P X ZB max 5.0 (0"). 0.7 9.7 9 88.9 88.9 55.6 0. 5. 98.5.5 5..8 0.7 7.0 08.0 5.9 6.6.9.6 7.9 0.8 (") 9.7 77.8 /.7 See note 0.6 0.6 9. 9.7 6. 58.0 57. 6.5 69.9 6.5.9 68. 57. 9.7 00.0 9. 55.6 Notes The dimensional drawings above show 5mm (0 ) bore models fitted with four tie rods, but can also be used to determine dimensions for 0.8mm ( ) bore models fitted with 6 tie rods Tie rod nuts are flush with head and cap on 0.8mm ( ) cylinders Dimension XI to be specified by customer lange ports to ISO 66 are also available see page 5 Parker Hannifin urope
Catalogue H07-0/U Side Lug & Clevis 5.0-0.8mm bores H Series See Notes,,, ZB + stroke L + stroke. max SB ( holes) ST / -0.5-0.0 Style C Side Lug (NPA Style MS) XS SW SS + stroke SW TS US SW. max ZC + stroke CD M Style BB Cap ixed Clevis (NPA Style MP) CW CB CW XC + stroke L See Notes,,, 5 Dimensions C & BB See also rod end dimensions, page 0 & mounting information, page 0 5.0 (0") 0.8 (") CB CD +0.00-0.08 CW (BSPP) & L M SB ST SW TS US XS 0.6 88.9 0.7 9.7 9 98. 90.0 9 57.. 0. 85.8 5.9.. 0.6 57. 77.8 /.7 See.8.. 9 76. 79. 58.0 note 8. + Stroke L P SS XC ZB max ZC 0.7 8. 08.0 5.9 5. 7.0 90.5 6.5 56.6 68. 57. 66.7.9 569.9.6 7.9 9. 55.6 57. 579. 665. 67.5 Notes The dimensional drawings above show 5mm (0 ) bore models fitted with four tie rods, but can also be used to determine dimensions for 0.8mm ( ) bore models fitted with 6 tie rods Tie rod nuts are flush with head and cap on 0.8mm ( ) cylinders Style C cylinders can be supplied with the cylinder ports arranged for mounting and sealing to a manifold surface see page lange ports to ISO 66 are also available see page 5 5 Supplied complete with pivot pin 5 Parker Hannifin urope
Catalogue H07-0/U Double Cylinders H Series ZM + x stroke ZL + stroke LD + stroke ZM + x stroke ZL + stroke L + stroke MM MM XS Double Cylinders 8. to 0.mm s S* + stroke Available with Styles TB, TD,, B,, C,, D, DD, and XS Double Cylinders 5 and 0.8mm s SS + stroke Available with Styles, B,, C, D, and DD Mounting Styles and Codes Double rod cylinders are denoted by a in the model code, shown on page. Dimensions To obtain dimensional information for double rod cylinders, first select the desired mounting style by referring to the corresponding single rod models shown on the preceding pages. Dimensions for the appropriate single rod model should be supplemented by those from the table opposite to provide a full set of dimensions. Strength Double rod cylinders employ two separate piston rods, with one screwed into the end of the other within the piston rod assembly. As a result, one piston rod is stronger than the other. The stronger rod is identified by the letter stamped on its end, and its pressure limitations with a : design factor are identical to those shown in the table on page for the equivalent single rod assembly. The weaker rod should always be used for the lighter duty. Pressure limitations for the weaker rod in pull applications at a : design factor are also identical to those on page, except for the bore sizes shown in the table below. Diameter : Design actor (bar) 6.5 ( / ") 5. (") 95 8.6 ( / ").9 ( / 8") 5 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5.0 (0") 0.8 (") All All All MM Diameter 5.9 ( 5 / 8") 5. (") 5. (").9 ( / 8") 5. (").5 ( / ").9 ( / 8").9 ( / 8") (").5 ( / ").5 ( / ") 6.5 ( / ") (") (") 88.9 ( / ") 6.5 ( / ") 76. (") All All All 7.0 (5") 9.7 (5 / ") + Stroke + x Stroke LD L ZL S SN SS 5 ZM.9 68. 7.6 87. 7.0 0.8 77.8 9.7 55.6 58.8 8. 96.9 09.6 85.7 9. 88.9 0.6 95. 0.7 0. 7.0 6.5 6. 9.7 58.8 65. 65. 65. 0. 7.0 98. 06. 76. 9.. 88.9. 5.0 95. 08.0 85.7 08.0 0.7 9.7 06. 96.9. 09.6 8.6 7.7. 7.7 66.7 5.0 66.7 79. 79. 79. 8. 9..9.8 0. 0.6 66.7.9 58.7 6.5 6. 0. 9. 9.7 56.6 7.5 55.6 08.0. 5. 57. 68. 9. 66.7 5. Combination s Double rod cylinders with rods of differing rod diameters are also available. Please contact the factory for details. Cushioning Double rod cylinders can be supplied with cushions at either or both ends. Cushioning requirements should be specified by inserting a C in the ordering code see page. Double rod cylinders with optional cushioning are supplied with floating cushion sleeves at both ends. Use LD dimensions for 8.mm to 0.mm ( / to 8 ) bore sizes Use L dimensions for 5.0mm & 0.8mm (0 & ) bore sizes S dimensions apply to mounting style only SN dimensions apply to mounting style only 5 SS dimensions apply to mounting style C only Style 9 nds If a stroke of less than 5mm on bore sizes up to 8.6mm ( / ), or a stroke of less than 00mm on bore sizes of 0.6mm ( ) and over, is required, where Style 9 rod ends are required at both ends, please consult the factory. 6 Parker Hannifin urope
Catalogue H07-0/U Accessories Accessory Selection Accessories for the rod end of a cylinder are selected by reference to the rod end thread, shown on pages and 0, while accessories for use at the cap end are selected by cylinder bore size. and Cap nd Accessories nd rod clevis, eye bracket and pivot pin plain rod eye, clevis bracket and pivot pin rod eye with spherical bearing Cap nd eye bracket for style BB mounting (Note: pivot pin is supplied with cylinder) nd atigue atigue failure of the rod end is minimised by using a shouldered rod end, ie: Style, and tightening accessories securely against the rod shoulder. Where this is not the case, derating of the maximum working pressure may be required please consult the factory. Clevis, ye Bracket and Pivot Pin H Series Load Capacity The load capacities of the accessories shown on these pages is the recommended maximum load based on a : factor of safety in tension. (Pivot pin is rated in shear). Before specifying, compare the actual load or the pull force at maximum operating pressure of the cylinder with the load capacity of the accessory you plan to use. If the load or pull force of the cylinder exceeds the load capacity of the accessory, please consult the factory. Pivot Pin Diameters To obtain the same diameter of pivot pin at the rod end and cap end of a style BB clevis-mounted cylinder fitted with a rod clevis or plain rod eye, a no. rod should be specified. Pivot pins of the same diameter can be obtained at each end of a style SBa cylinder fitted with a rod end spherical bearing by specifying a style 7 rod end and nos., or rods, as indicated in the table on page. Plain ye, Clevis Bracket and Pivot Pin Thread Clevis ye Bracket Pivot Pin Nominal orce kn Mass kg Thread Plain ye Clevis Bracket Pivot Pin Nominal orce kn Mass kg M0x.5 Mx.5 M0x.5 Mx.5 M6x.5 Mx M9x M5x M8x M58x M6x M68x M76x M90x M00x M0x 5090 6995 68 8. 0.7 509 6995 68 8. 0.7 509 9696 69 6.8. 509 856 6870 8.8 5. 509 856 6870 9.0 5. 5095 6998 687 9.9 5096 856 687 0. 5097 856 687. 8.6 5098 856 687. 8.5 5099 856 687 0.0 8. 50950 8565 6875 0.0 5.9 5095 8565 6875 5.6 6. 5095 758 755 56.0 0.8 5095 759 757. 57.8 5095 759 757. 56.6 M0x.5 Mx.5 M0x.5 Mx.5 M6x.5 Mx M9x M5x M8x M58x M6x M68x M76x M90x M00x M0x 69089 6905 68.. 69090 6905 68 5.. 6909 6906 69 5.0. 6909 6907 6870 58.0 6.6 6909 6907 6870 85.6 6.6 6909 6908 687 9..7 69095 6909 687 5.6. 69096 690 695 7.. 69097 690 695 7..5 69098 69 687 55.6 5. 69099 69 6875 50.7 65. 6900 69 696 6.6 6 756 75 755 7. 6.7 77 75 755 7..0 78 75 88 57.5 80.7 79 75 757 8. 7.5 Cylinder accessory dimensions conform to NPA recommended standard, NPA/T.6.8. - 98 ye with Spherical Bearing Thread M6x.5 M0x.5 M7x Mx Mx M8x M6x Part Torque Load Nm Mass kg 59 0. 50 0.7 5. 5. 5 6. 5 80 7.6 55 95.5 Cap nd ye Bracket for Style BB Cylinders 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5.0 (0") 0.8 (") ye Bracket Part Nominal orce kn Mass kg 6995 8. 0. 6996 6.8.5 6996 6.8.5 856 9.0. 6998 5.6 856 0.6. 856. 7.0 856 0.0 7. 8565 5.6 5.8 758 56.0 55.6 759. 8. 7 Parker Hannifin urope
Catalogue H07-0/U Accessories H Series Clevis, ye Bracket and Pivot Pin Clevis Dimensions Part 5090 509 509 509 509 5095 5096 5097 5098 5099 50950 5095 5095 5095 5095 A CB CD +0.0 Nominal Mass C CW +0.05 orce kn kg 9. 9.8.70 8..7.7 M0x.5 8.9 0. 9. 9.8.70 8..7.7 Mx.5.9 0. 8.6.6 9.05 5.0 5.9 9. M0x.5 9.9 0.6. 8.9 5.0 7.6 9. 5. Mx.5 8.8.. 8.9 5.0 7.6 9. 5. M6x.5 96.7. 5.6.9 95. 5..9 Mx 9.. 57. 6.7.5..8.5 M9x 0. 6.0 76. 6.7 0 9.7.8 M5x 7.9 8. 76. 6.7 0 9.7.8 M8x.6 8. 88.9 77. 6.50 65. 8. 6.5 M58x 80. 5. 88.9 77. 76.0 7.5 8. 69.9 M6x 55. 9.0 88.9 77. 76.0 7.5 8. 69.9 M68x 589.9 8.7 88.9 0.8 88.90 96.9 88.9 M76x 08.8. 0.6 6.0 0.60.8 57. 0.6 M90x 9. 9.8 0.6 6.0 0.60.8 57. 0.6 M00x 80.0 8.6 Clevis (emale Clevis) CW CD CB CW C A ye Bracket Dimensions Part 6995 6996 856 6998 856 856 856 8565 758 759 CB CD +0.0 +0.05 Nominal Mass DD L L M M orce kn kg 9..70 0. 6.5 8.6 9..7.. 8. 0..8 9.05.5 88.9 5.9 7.6.8 9.. 6.8 6.8.5 8. 5.0 6.7.. 60. 8. 5..8 8.6 9.0..9 6.7 7.0. 76. 5.0.9. 97.0 5.6 6.5.5.0 65. 8.6 85.7 57..5 5.0 5.7 0.6. 6.5 0 7.0 90.5 8. 0.6 6.5 6.9 5.5. 7.0 76. 6.50 0. 5.9.5 0.6 76. 6.5 76. 67. 0.0 7. 76. 76.0... 8.6 69.9 8.6 90.5 5.6 5.8 0.6 88.90 6.0 0.7.9.5 0.6 88.9 95.. 56.0 55.6. 0.60 5. 77.8 9. 6.5. 0.6 08.0 90.8. 8. ye Bracket M 5 L L M CB CD DD (x) Cylinder accessory dimensions conform to NPA recommended standard, NPA/T.6.8. - 98 Pivot Pin for Clevis Bracket & ye Bracket Part 68 69 6870 687 687 687 695 687 6875 696 755 88 757 CD +0.00-0.05 CL Nominal orce kn Mass kg.7 5.8 56 8. 0. 9.08 6.9 75. 0. 5. 77. 88 5.9 0.5.95 0.9 5 89.8..8 8. 69.. 9. 5 6.7. 0.9 58 6.7.5 6.5 5.6 7 957. 5.9 76. 5. 7 78.7 8.6 76. 67. 85 78.7 9. 88.9 05. 5 876.8 5. 0.6 9.8 5 5.9. 0.6. 66.7 5.9.5 Pivot Pin for Clevis Bracket & ye Bracket CL CD 8 Parker Hannifin urope
Catalogue H07-0/U Accessories H Series Plain ye, Clevis Bracket and Pivot Pin Plain ye Dimensions Part 69089 69090 6909 6909 6909 6909 69095 69096 69097 69098 69099 6900 756 77 78 79 A min. CA CB CD +0.0 +0.05 Nominal orce kn Mass kg 9. 8. 9..70 8. M0x.5. 0. 9. 8. 9..70 8. Mx.5 5. 0. 8.6 5..8 9.05 7.0 M0x.5 5.0 0.5 8.6 60. 8. 5.0 6.5 Mx.5 58.0.. 7. 8. 5.0 6.5 M6x.5 96.8. 87..9 50.0 Mx 9..6 57. 0.6 6.5.5 6.5 M9x 00.6 5. 57.. 6.5 0 7. M5x 8.6 6. 76. 7.0 6.5 0 7. M8x. 6.8 88.9 7.6 76. 6.50 90.5 M58x 0.. 88.9 55.6 76. 76.0 08.0 M6x 90.5 6.0 9. 65. 88.9 76.0 08.0 M68x 59.8 9.6 0.6 9.7 0.6 88.90 6. M76x 79.. 7.0 9.7 0.6 88.90 6. M90x 969.0 8. 9.7.8. 0.60.5 M00x 0.9.5 9.7.8 7.0 0.60.5 M0x 75.6 8. Plain ye CD CD CD CA Clevis Bracket M CD CB CW CW CB A min. Clevis Bracket Dimensions Part CB CD +0.0 Nominal Mass CW DD L L M M +0.05 orce kn kg M L 5 L CD DD (x) 6905 6906 6907 6908 6909 690 69 69 69 75 75 75 9.8.70.7 0. 88.9.7 8. 9..7 5.9 6.8.6.0.6 9.05 5.9.5 7.0 5.9 7.6 0. 9..0 97.0 6..5 8.9 5.0 9. 6.7 65. 9. 57. 8. 5..8 5.7 85.6 5.0 5.6.9 5. 6.7 90.5. 76..9. 5.5 6.6 8.8 6.7.5.8.0.. 9. 69.9.5 56. 90.5 5.6 5.9 6.7 0 8. 7.0.9 5. 08.0 8.0 57. 70.6 8.8 7.. 77. 6.50 8. 0..9 5.. 88.9 6.5 79. 8.8 55.6. 77. 76.0 8...9 5. 5. 08.0 76. 9. 8.8 50.7 0.7 90. 76.0 8...9 5. 5. 08.0 76. 9. 8.8 6.6 0.7 0.8 88.90 6.0 9.7.9 69.9 7.0 88.9 0.8 0.8 7. 80. 6.0 0.60 5..5 9. 95. 6. 0.6.8 9. 57.5 5.8 8. 0.60 5..5 9. 95. 6. 0.6.8 9. 8. 0.6 ye with Spherical Bearing ISO 698 C L CH CN N z AX b ye with Spherical Bearing Dimensions ISO 698 Part 59 50 5 5 5 5 55 AX min. b C max. CH CN H7 max. N h (Style 7) L Z Clamp screw torque (Nm) 5 50 5 0 5 0 M6x.5 0. 9 0 6 65 5 5 M0x.5 7 0.7 7 8 76 80 0 M7x. 6 7 97 97 0 50 0 Mx. 57 58 8 0 50 6 50 Mx 50 6. 6 70 0 6 7 6 M8x 6 80 7.6 90 80 80 80 90 80 M6x 78 95.5 Mass kg 9 Parker Hannifin urope
Catalogue H07-0/U Mounting Information Mounting Styles eneral guidance for the selection of mounting styles is given on page 9. The notes which follow provide information for use in specific applications. Mounting Bolts Parker recommends that mounting bolts with a minimum strength of ISO 898/ grade 0.9 should be used for fixing cylinders to the machine or base. This recommendation is of particular importance where bolts are placed in tension or subjected to shear forces. Mounting bolts should be torque loaded to their manufacturer s recommended figures. Tie Nuts Tie rod mounting nuts, with lubricated threads, should be to a minimum strength of ISO 898/ grade 0, torque loaded to the figures shown. xtended Tie s The standard tie rod extension for cylinders with mounting styles TB, TC and TD is shown as BB in dimension tables. Longer or shorter extensions can be supplied. Cylinders are supplied with an additional set of mounting nuts see table. 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") 5.0 (0") 0.8 (") Tie Nuts Size A/ Torque Nm min-max. 5-7 9. 60-65 9. 60-65.8 60-65.8 75-80. 0-5 8. 75-75.9 080-00 7.6 560-580 90-0 75-75 Cylinders may be ordered with extended tie rods in addition to another mounting style. The extended tie rods may then be used for mounting other systems or machine components. lange Mounted Cylinders The diameter of the rod gland extension (B) at the head end can be used as a pilot to locate the cylinders in relation to the machine. After alignment has been obtained, the flanges may be drilled for pins or dowels to prevent movement. Pivot Mountings Pivot pins are supplied with style BB cap fixed clevis mounted cylinders. Pivot pins are not supplied with the spherical bearing mounting, style SBa, as the pin length will be determined by the customer s equipment. Spherical Bearings Where a spherical bearing mounting, style SBa, is specified for the cylinder, a rod eye with spherical bearing should be used at the rod end. The life of spherical bearings is influenced by factors such as specific load, direction of load, angle of oscillation, and type and frequency of lubrication. The maximum pressure rating for spherical bearing cylinders is 60 bar. If unusual operating conditions exist, please consult the factory. H Series Trunnion Mounted Cylinders Trunnions require lubricated pillow blocks with minimum bearing clearances. Blocks should be aligned and mounted to eliminate bending moments on the trunnion pins. Self-aligning mounts must not be used to support the trunnions as bending forces can be set up. The position of an intermediate fixed trunnion is fixed during manufacture and its location must be specified at the time of order. oot Mountings and Thrust eys The turning moment which results from the application of force by a foot mounted cylinder must be resisted by secure mounting and effective guidance of the load. A thrust key modification is recommended to provide positive cylinder location. Thrust key mountings eliminate the need for fitted bolts or external keys on Styles C, and side mounted cylinders. The gland retainer plate is extended below the nominal mounting surface to fit into a keyway milled into the mounting surface of PD the machine member. See Mounting Modifications in the order code, page. PA A Integral ey 8. ( / ") (") 6.5 ( / ") 8.6 ( / ") 0.6 (") 7.0 (5") 5. (6") 77.8 (7") 0. (8") Nom. A +0.0-0.075 Tie Supports To increase the resistance to buckling of long stroke cylinders, tie rod supports may be fitted. These move the tie rods radially outwards and allow longer than normal strokes to be used without the need for an additional mounting. 8. 6.5 8.6 0.6 PA +0.0-0. sizes above 0.6mm ( ) do not require tie rod supports. PD 8.9 6.5 5.9 8.0 6.0 5.9 8. 5. 9. 8 9.7 66.7.. 7.6.. 9.7 5. 5.7 08.0 5. 5.7 0.7 5. 5.7. Stroke (metres) 0.9..5.8...7.0..6.9. Number of supports req'd. 0 Parker Hannifin urope