REPAIR INSTRUCTIONS UNDER BODY CYLINDER (UM, UL)

Size: px
Start display at page:

Download "REPAIR INSTRUCTIONS UNDER BODY CYLINDER (UM, UL)"

Transcription

1

2 Table of contents 1. Introduction Scope of use General remarks Contact Hyva Precautions Spare parts Prior to use Recycling and Reuse of components General Reuse of components Warranty Disassembly Components UM Components UL Removing the cylinder from the vehicle UMB and ULB removal UME and ULE removal Removing the cylinder from the cradle Dismantling the cylinder Opening the base of the UL cylinder Opening the base of the UM cylinder Removing the piston Removing the stages Cylinder Assembly Replacing packset Replacing stages Replace piston Closing the cylinder UL Bottom plate UM Bottom Refitting the cylinder to the vehicle Connecting and testing the cylinder Connection of the hydraulic system Final Checks Painting the cylinder Spare part codes Exploded view UMB cylinder subject to change without notice 2 OH-E CYL-0025 / / RV AC

3 1. Introduction 1.1. Scope of use This manual is for repair workshops and service partners repairing the Hyva under body cylinders, manufactured from 2010 onwards (the UM and UL series), where it is necessary to disassemble the cylinder to replace parts that are subject to wear (i.e. seal kit). The Hyva underbody cylinder range includes Underbody-Medium-Ball (UMB), Underbody-Medium-Eye (UME), Underbody-Light-Ball (ULB) and Underbody-Light-Eye (ULE) cylinders. Separate instructions are available for other types of cylinders. Always use original Hyva components General remarks Specification sheets are available for all Hyva cylinders; these sheets contain all relevant dimensional and application information about your cylinder. The Hyva cylinder has been developed for lifting purposes only and its use for any other purpose is prohibited. The cylinder is not to be used as a stabiliser and any kind of side-load must be avoided whenever possible. For two- or three-way tipping a cradle has to be used. For a vehicle designated for rear or side tipping, Hyva highly recommend to use a cradle for cylinders with a stroke of 1000 mm and more. This is to minimise side load and to ensure a longer packset life. Warning Applying side-load to any cylinder is dangerous. The cylinder should be mounted with a minimum pull out of 15 mm and a maximum pull out of 50 mm (the closed length of the cylinder on the Hyva specification sheet already includes 20 mm pull out). The advice given in these pages is by no means complete and should not be used as an alternative to common sense. See Hyva document OIL-0002 for recommended oils Contact Hyva If you have any questions concerning the application, installation, operation or repair of any Hyva product - please contact your nearest Hyva Service Partner and check the Hyva website (both for documentation as for service partner coordinates): subject to change without notice 3 OH-E CYL-0025 / / RV AC

4 1.4. Precautions Ensure there is enough free working space for mounting the cylinder. If the tipper body is on the truck chassis, lift the body using an overhead crane or a similar device. If the tipper body is raised to create working space, support the body using body props before mounting the cylinder. Danger Working under an unsupported tipper body is a danger to life. To avoid damage to the truck cabin, cover the rear of the cab with a tarpaulin. If necessary tilt the vehicles cabin (see the truck manual for details). Disconnect the vehicle s battery leads before any welding. Warning Not using the appropriate equipment when lifting parts (such as the proper sling for a cylinder) is a danger to life. Some parts in the cylinder are mounted under tension (i.e. snap rings) they may spring out when removed. They should be secured when removed to prevent injury. Ensure any oil spilt during installation and testing is disposed of in an environmental friendly way Spare parts To avoid ordering the wrong parts Hyva recommends ordering spare parts listed in this document, see also Prior to use Clean all parts to remove any dust, dirt or protective coatings. Check parts for damage during transport or storage. Do not use any damaged parts. If for any reason the above conditions cannot be met contact your nearest Hyva Service Partner for further guidance Recycling and Reuse of components General Remove and dismantle the components as described in this manual. Clean all parts thoroughly (using degreaser and compressed air). All oil products must be disposed of in an environmental friendly manner (usually by a licensed disposal agent). The components can then be recycled in the normal way. For example; non-metal components such as seals and wipers with plastic materials, clean steel parts with other scrap metals Reuse of components When the Hyva cylinder is stripped (for example after inspecting a cylinder) some parts may be reused. Warning Never use parts from a cylinder that has been subject to overpressure. Using second hand parts in cylinder repairs can change the function or operating conditions of the cylinder and may affect the terms of warranty. subject to change without notice 4 OH-E CYL-0025 / / RV AC

5 Assuming the following parts are in good working condition (i.e. no visible damage such as scratches, imprints or deformation, no corrosion and dimensionally correct) then they may be reused: Base, Stages, and Piston, Sliders, Bottom Lift rings when not deformed during dismantling Spherical Cup, Locking Ring Set and Circlip Cradle, Brackets The following parts must never be reused: Packset (seals, wear rings, wipers) O-ring 1.7. Warranty The Hyva International B.V. warranty terms are described in the General Sales Terms, Hyva document FO- E subject to change without notice 5 OH-E CYL-0025 / / RV AC

6 2. Disassembly 2.1. Components UM FIGURE 1: CROSS-SECTION OF THE UMB CYLINDER Components: 1 = 1 wiper 2 = 1 wear ring (stages shorter than 500 mm) = 2 wear rings (stages longer than 500 mm) 3 = 1 seal 4 = 1 inner stop ring 5 = 1 slider 6 = 1 lift ring* * Stage diameters 091, 110, 129 & 149 have rectangular lift rings Stage diameters 072, 169 & 191 have round lift rings subject to change without notice 6 OH-E CYL-0025 / / RV AC

7 2.2. Components UL FIGURE 2: CROSS-SECTION OF THE ULB CYLINDER Components: 1 = 1 wiper 2 = 1 wear ring 3 = 1 seal 4 = 1 inner stop ring 5 = 1 slider 6 = 1 lift ring (round) subject to change without notice 7 OH-E CYL-0025 / / RV AC

8 2.3. Removing the cylinder from the vehicle Danger Working under an unsupported tipper body is a danger to life! UMB and ULB removal Tip the body or lift this with another device and secure the body with a support. Remove the circlip, locking ring set and spherical piston cup (Figure 3). Spherical Locking rings Circlip FIGURE UME and ULE removal Tip the body or lift this with another device and secure the body with a support. Remove the pivot pin from the piston eye, the actual method will depend on eye and top bracket. In general remove the split-pin and then remove the pivot pin (Figure 4). FIGURE 4 subject to change without notice 8 OH-E CYL-0025 / / RV AC

9 Removing the cylinder from the cradle Disconnect the hydraulic connection after having made sure there is no pressure left in the system. Unscrew the bolts from the cradle, remove closing plates and remove cylinder (in case of no obstruction). FIGURE 5: REMOVAL OF THE CYLINDER FROM THE CRADLE subject to change without notice 9 OH-E CYL-0025 / / RV AC

10 2.4. Dismantling the cylinder Place the cylinder horizontal on a clean bench with the oil inlet facing down. Clamp the base securely to assure safe working conditions (a V block arrangement is usually the best) and collect any waste oil Opening the base of the UL cylinder Push with a soft-headed mallet or similar the bottom plate inside (approximately 20mm). Remove the snap-ring by pushing the tip of a screwdriver under the ring at one end and levering the ring out (Figure 6). If necessary, remove paint before removing bottom. Warning The snap-ring is mounted under tension, it may spring out which can be dangerous. FIGURE 6 Strike the head of the piston with a soft-headed mallet or similar. This will push the bottom plate from the base tube. (Figure 7) FIGURE 7 Remove the O-ring from the bottom plate (Figure 8). FIGURE 8 subject to change without notice 10 OH-E CYL-0025 / / RV AC

11 Opening the base of the UM cylinder Unscrew the locking screw from the bottom nut and use a chain spanner to disassemble the bottom nut. Remove the O- ring from the bottom. FIGURE Removing the piston All pistons have two part sliders, these should be removed to avoid loss or damage. To remove the piston, push the piston into the stage until the lift ring is visible at the inside diameter of the larger stage (Figure 10). Warning The lift ring is mounted under tension, it may spring out which can be dangerous! Remove the lift ring by pushing the tip of a screwdriver under the ring at one end and levering the ring out (Figure 10). FIGURE 10 The piston can now be removed through the bottom of the cylinder (Figure 11). FIGURE 11 subject to change without notice 11 OH-E CYL-0025 / / RV AC

12 Removing the stages Warning The stages must be placed on a clean surface to prevent scratches and other damage. Never remove a stop ring, if it shows signs of damage the whole stage must be replaced. The seals, wear rings and wipers must not be re-used. Before a stage can be removed through the bottom of the cylinder, the lift ring of the next stage must be removed. Remove the lift ring in the same way as for the smallest stage. The stage can then be removed through the bottom of the cylinder. Subsequent stages can be removed in the same way. Remove the seal, wiper and wear rings from the internal grooves at the top of each stage (Figure 12). Warning Do not remove the seals and wipers with a screwdriver or other sharp instrument as this may irreparably damage the grooves and cause leaks. Only the wear rings can be removed with a screwdriver. FIGURE 12 Clean each stage carefully and check each groove and the tube surface for any irregularities. Check also the sliders on each tube; if these are damaged, they should be replaced. If the slider is damaged, check the stop ring in the larger stage tube for signs of damage or twisting. subject to change without notice 12 OH-E CYL-0025 / / RV AC

13 3. Cylinder Assembly 3.1. Replacing packset Clean each stage thoroughly and apply sufficient grease to the packset and the grooves (Figure 13). Put a new packset into each stage (Figure 14); starting with the seal, followed by the wear rings FIGURE 13 and the wiper Caution Ensure that each of the rings are seated correctly in the grooves; incorrect fitting can cause seizure, leaks or damage. FIGURE 14 subject to change without notice 13 OH-E CYL-0025 / / RV AC

14 3.2. Replacing stages Slide the first (largest) stage almost fully in the base tube (Figure 15), ensuring that the stage is not scratched when passing the inner stop ring. Some resistance will occur when the tube enters the packset. To prevent damage and assemble easy, use grease at bottom inside of the base tube. FIGURE 15 Place the sliders at the bottom side of the stage (Figure 16). Slide the tube further in to the base until the sliders are in the base tube. Sliders 149 and bigger for UM cylinder must be mounted with the flat side facing upwards (which contacts inner stopring). FIGURE 16 After mounting a stage, fit the lift ring (Figure 17) in the previous stage (except for the cylinder base). Subsequent stages can be mounted in the same way. subject to change without notice 14 OH-E CYL-0025 / / RV AC

15 3.3. Replace piston The piston tube is mounted in the reverse sequence to dismantling. Make sure that no sharp edges are at the top side that can damage the packset Closing the cylinder UL Bottom plate Clean the groove for the bottom plate O-ring. Fit a new O-ring to the bottom plate and slide the bottom plate into the base (Figure 18) using plenty of grease (Figure 19) to avoid damage to the O-ring. FIGURE 18 FIGURE 19 The bottom plate is mounted in the reverse sequence to dismantling. subject to change without notice 15 OH-E CYL-0025 / / RV AC

16 UM Bottom Clean the groove for the bottom O-ring. Fit a new O-ring to the bottom and screw the bottom on the base (Figure 20) using plenty of grease to avoid damage to the O-ring. FIGURE 20 The bottom is mounted in the reverse sequence to dismantling Refitting the cylinder to the vehicle The mounting instructions are described in Hyva document CYL subject to change without notice 16 OH-E CYL-0025 / / RV AC

17 4. Connecting and testing the cylinder 4.1. Connection of the hydraulic system Connect the hydraulic system as specified by the hydraulic kit. Remove the plug from the oil-inlet and connect the cylinder to the hydraulic system (Figure 21). Do not fully screw in oil inlet adaptor but leave 1-2 mm to give the adaptor the possibility to rotate (swivel). FIGURE 21. EXAMPLE OF A HYDRAULIC SYSTEM Ensure there is sufficient hose length so it does not obstruct the movement of the cylinder while tipping. It is not necessary to bleed air from the cylinder after assembly (air is automatically discharged during the first few tips). subject to change without notice 17 OH-E CYL-0025 / / RV AC

18 4.2. Final Checks The first tip should be slow and all movements are to be closely observed to check: Cylinder movement is smooth Hoses do not interfere with any parts Cylinder extends in a straight line While tipping, there is no contact between the rear/side end of the body and other parts of the truck (such as towing-hooks, tail lamps etc.) Tip the body 4 or 5 times and check there is no side-load on the cylinder and the clearances are correct. If you find the cylinder movement is stiff, loosen the bolts and realign the cylinder. Protect hoses where they move against metal parts (if they cannot be repositioned). It is not necessary to bleed air from the cylinder. Tip During the first few tips some packset grease may appear on the stages of the cylinder, this is normal and does not mean the cylinder is leaking. Where the installation does not operate as expected, see Operating & Maintenance Instructions Complete Tipper for full details of use including trouble-shooting guide (Hyva document: TIP-0005). Cylinder stages should extend in right sequence: largest (first stage) extends first, then second stage etc. With a new cylinder, a light empty body and high pump flow however, stages can extend in wrong sequence (mismatching). But this will disappear in normal operation (loaded body) Painting the cylinder When repainting, do not repaint the blank parts of the cylinder e.g. trunnion pins, piston, stages, wipers, balls/eyes. subject to change without notice 18 OH-E CYL-0025 / / RV AC

19 5. Spare part codes Tip Use nylon rod ( ) to ease the dismantling of the cylinder Consult the appropriate specification sheet for each special cylinder version I Parts for piston ball mounting Retainer kits for UMB and ULB cylinders. Retainer kits contain the spherical cup, locking rings and circlip. Ball Retainer kit Diameter D D D D TABLE 1: RETAINER KITS II Sealkits, bottom plate O-ring, oil inlets and retainer kits Cylinder Type Seal kit Part Number Bottom Plate O-ring Oil inlet Retainer kit UL K 75 x 4 70 shore 1/2" p/n: UL K UL K 90 x 4 70 shore UL K UL K 107 x 4 70 shore UL K UL K UM 129-3* K UM 129-4* K UM 129-5* K UM (>500) ** K UM 149-4* K /4" p/n: UM 149-5* K UM 149-6* K UM (>500) ** K UM 169-5* K UM 169-6* K UM 169-7* K UM 191-5* K UM 191-6* K UM 191-7* K UM 191-8* K TABLE 2: SEALKITS, BOTTOM PLATE O-RING, OIL INLETS AND RETAINER KITS NOTES: * After opening an UM cylinder, a new locking screw M6 should be applied in the bottom after remounting the bottom, p/n ** Cylinders with a stage length bigger than 500 mm have a different packset: 2 wearrings per stage instead of one subject to change without notice 19 OH-E CYL-0025 / / RV AC

20 6. Exploded view UMB cylinder 0 / 20 / 30 / 40- WIPER, WEARRING(S) AND SEAL 1- BASE 21- STAGE 31- STAGE 41- STAGE 100- RETAINER KIT 2- BOTTOM O-RING 22- SLIDER 32- SLIDER 42- SLIDER 101- PISTON 3- BOTTOM 23- LIFT RING 33- LIFT RING 43- LIFT RING 102- SLIDER 4- LOCKING SCREW 5- OIL INLET The sealkit contains all relevant wipers, wearrings, seals and bottom O-ring for the specific cylinder. subject to change without notice 20 OH-E CYL-0025 / / RV AC

Pallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification

Pallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification OWNER S MANUAL Model MH1230 Important Safety Instructions Assembly Instructions Parts and Hardware Identification Pallet Jack CAUTION: Read, understand and follow ALL instructions before using this product

More information

Model No: VS4815 1. SAFETY INSTRUCTIONS VS4800 2. INTRODUCTION & APPLICATIONS VS4815 3. CONTENTS. 2.1 Introduction. 2.

Model No: VS4815 1. SAFETY INSTRUCTIONS VS4800 2. INTRODUCTION & APPLICATIONS VS4815 3. CONTENTS. 2.1 Introduction. 2. Instructions for: Petrol Engine Twin Camshaft Setting / Locking Tool Kit - (incorporating Vanos Alignment) - BMW N42 & N46 Engines Model No: VS4800 Associated kit: Camshaft/Carrier Bracket Remover & Installer

More information

Drive shaft, servicing

Drive shaft, servicing Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,

More information

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com.

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. 2 0 0 5 D U K E A I R X C / S L / R A C E S E R V I C E G U I D E Information

More information

Operating Instructions Parts List Manual Scissor Lift Pallet Truck

Operating Instructions Parts List Manual Scissor Lift Pallet Truck Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors

More information

2006 JUDY SERVICE GUIDE

2006 JUDY SERVICE GUIDE 2006 JUDY SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Information contained in this publication is subject

More information

This instruction is valid for all ACD pump models shown on page 2

This instruction is valid for all ACD pump models shown on page 2 Screw pumps ACD Maintenance and Service Instruction This instruction is valid for all ACD pump models shown on page 2 Contents Page List of components 2 Exploded view/ordering code 3 Service intervals

More information

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com.

For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Information contained in this publication is subject to change at anytime

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46) 46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel

More information

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008) Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the

More information

2006 HEADSHOK Service Video #1

2006 HEADSHOK Service Video #1 LEFTY SPEED DLR DAMPING CARTRIDGE This document explains how to properly remove, disassemble, inspect, reassemble and reinstall the Lefty Speed DLR2 damping cartridge. It is a document to be used in conjunction

More information

POSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT

POSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT POSEION 2-29, 2-25 & 2-22 POSEION 2-29, 2-25 & 2-22 XT Repair Manual Index A. Safety precautions 3 B. Technical data 4 C. Structure 5-6. Service / Repair 7-23 E. Tools 24 F. Function 25-26 G. Electric

More information

Cylinder head, removing and replacing

Cylinder head, removing and replacing 15-1 Cylinder head, removing and replacing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once, and are unreliable and may fail

More information

DANGER DANGER. General Information. Safety Is Your Responsibility. Ordering Parts. Contact Information

DANGER DANGER. General Information. Safety Is Your Responsibility. Ordering Parts. Contact Information Safety Safety Is Your Responsibility DANGER To avoid personal injury or death, carefully read and understand all instructions pertaining to the Anthony Liftgates product. Do not attempt to install, operate,

More information

DYNA RIDER FOOTBOARD KIT

DYNA RIDER FOOTBOARD KIT -J0 REV. 0-0-0 DYNA RIDER FOOTBOARD KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English

More information

Front axle components, overview

Front axle components, overview just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,

More information

HYDRAULIC TABLE CART 500-LB.

HYDRAULIC TABLE CART 500-LB. HYDRAULIC TABLE CART 500-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic

More information

HYDRAULIC LIFT TABLE CART 2200-LB.

HYDRAULIC LIFT TABLE CART 2200-LB. HYDRAULIC LIFT TABLE CART 2200-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47) 47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing

More information

Turbocharger system components, servicing

Turbocharger system components, servicing 21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners

More information

Service Manual Rol-Lift

Service Manual Rol-Lift R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing

More information

Front brakes (FN- 3), servicing

Front brakes (FN- 3), servicing j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly

More information

13. REAR WHEEL/BRAKE/SUSPENSION

13. REAR WHEEL/BRAKE/SUSPENSION 13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...

More information

M A N U A L 13-10-05

M A N U A L 13-10-05 Documentation The following information sheets illustrate the description below: 12-WW01-4G-E Sectional view of the lance with main dimensions 12-W101-6G-E Sectional view of the head of the lance with

More information

DiscPlus DX195 and DX225 Air Disc Brakes

DiscPlus DX195 and DX225 Air Disc Brakes Revised 11-04 Technical Bulletin Revised 1 Technical 11-04 Bulletin DiscPlus DX195 and DX225 Air Disc Brakes Inspection, Installation and Diagnostics Air Disc Brake Inspection Intervals and Procedures

More information

INSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05

INSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05 INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional

More information

Joplin Rebuild Instructions

Joplin Rebuild Instructions Joplin Rebuild Instructions This is a step by step list of instruction on how to rebuild the Crankbrothers Joplin post. It may not always be required to completely tear-down the post to do the work needed

More information

Rebuild Instructions for 70001 and 70010 Transmission

Rebuild Instructions for 70001 and 70010 Transmission Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before

More information

STEERING SYSTEM - POWER

STEERING SYSTEM - POWER STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and

More information

USE AND MAINTENANCE MANUAL

USE AND MAINTENANCE MANUAL FORKS POSITIONER Mod. FR-FP-FFP ORIGINAL INSTRUCTIONS INTRODUCTION This manual includes instructions for assembly, maintenance (regular and extraordinary), and for possible faults with remedies. The instructions

More information

MODEL T200-F18 MODEL T125-F18 Finish Nailers

MODEL T200-F18 MODEL T125-F18 Finish Nailers P MODEL T200-F18 MODEL T125-F18 Finish Nailers IMPORTANT! DO NOT DESTROY It is the customer s responsibility to have all operators and service personnel read and understand this manual. OPERATING MANUAL

More information

1 TON FOLDING CRANE CFC1000

1 TON FOLDING CRANE CFC1000 1 TON FOLDING CRANE CFC1000 OPERATION &MAINTENANCE INSTRUCTIONS 0401 SPECIFICATIONS MAXIMUM SAFE WORKING LOADS (kg) 1 2 3 4 1000 750 500 250 MAXIMUM LIFT HEIGHT - 1920mm HYDRAULIC RAM OIL CAPACITY - 450CC

More information

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997 Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47

More information

FJ2. 2 Ton Trolley Floor Jack Assembly & Operating Instructions

FJ2. 2 Ton Trolley Floor Jack Assembly & Operating Instructions FJ2 2 Ton Trolley Floor Jack Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

DIAMOND Retractable Rodding Robot Model SPRAYROD-R

DIAMOND Retractable Rodding Robot Model SPRAYROD-R 2004-12-21 2 1 (23) DIAMOND Retractable Rodding Robot Model SPRAYROD-R 2004-12-21 2 2 (23) Table of contents 1 TECHNICAL DESCRIPTION...4 1.1 MAIN DETAILS...5 1.2 COMPONENTS DESCRIPTION...5 1.2.1 Pneumatic

More information

Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19

Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19 Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR

More information

AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION

AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION

More information

PART 2 FORKLIFT HYDRAULIC SYSTEM

PART 2 FORKLIFT HYDRAULIC SYSTEM PART 2 FORKLIFT HYDRAULIC SYSTEM Chapter 1 Description and Operation Component Locations & Circuit Layouts 1 Hydraulic Pump 11 Control Valve 14 Valve Section Oil Flows 15 Anti-Cavitation Valve 22 Velocity

More information

Maintenance and Service Instruction

Maintenance and Service Instruction Screw pumps E4 Maintenance and Service Instruction E4 1 IMO AB This instruction is valid for all E4 pump models shown on page 2 Contents Page List of components 2 Exploded view/ordering code 3 Service

More information

Rear wheel brakes, servicing. Стр. 1 из 45. Note:

Rear wheel brakes, servicing. Стр. 1 из 45. Note: Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly

More information

2007 Hummer H3. 2007 BRAKES Disc Brakes - H3. Fastener Tightening Specifications Specification Application

2007 Hummer H3. 2007 BRAKES Disc Brakes - H3. Fastener Tightening Specifications Specification Application 2007 BRAKES Disc Brakes - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Backing Plate Bolts 135 N.m 100 lb ft Brake Hose

More information

2003-2004 SID REAR SERVICE GUIDE

2003-2004 SID REAR SERVICE GUIDE 2003-2004 SID REAR SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Contact your local distributor or visit

More information

TITAN 13 x 2 ½ BRAKES

TITAN 13 x 2 ½ BRAKES INSTALLATION INSTRUCTION AND SERVICE MANUAL Actuator/Trailer Dealer - Please provide these instructions to the consumer. Consumer - Read and follow these instructions. Keep them with the trailer for future

More information

HYDRAULIC TABLE CART

HYDRAULIC TABLE CART Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s

More information

Trillium 40 Axis Spring Tensioner Wire Replacement Instructions

Trillium 40 Axis Spring Tensioner Wire Replacement Instructions Trillium 40 Axis Spring Tensioner Wire Replacement Instructions 1 Overview The objective is to replace the broken axis spring tensioner wire. This requires the following tasks: 1. Remove the seismometer

More information

PALLET JACK - 2.5 TON

PALLET JACK - 2.5 TON PALLET JACK - 2.5 TON 39939 SET UP AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.

More information

2005-2007 Ford Focus Front Brake Rotors

2005-2007 Ford Focus Front Brake Rotors 2005-2007 Ford Focus Front Brake Rotors Replacement Replacing the rotors in 2005-2007 Ford Focus models with rear drum brakes. Written By: David Hodson INTRODUCTION The steps in this guide are used to

More information

Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna)

Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna) Installation Instructions Reverse Gear MAMBA (Monoblock for Cable operated) Read and become familiar with these installation instructions before start. Two Piece for H-D 5 Speed Trans., Cable operated

More information

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve

More information

ROUGHNECK II Pumpless Drain

ROUGHNECK II Pumpless Drain SERVICE BULLETIN SB4027 Rev. I 1/11 For Used Oil Only ROUGHNECK II Pumpless Drain Model #4110-022 FOR USED OIL ONLY (Black) For Antifreeze Only Model #4110-023 FOR USED ANTIFREEZE ONLY (Green) Patent #

More information

MODEL 565E - 22 TON AIR/HYDRAULIC AXLE JACK

MODEL 565E - 22 TON AIR/HYDRAULIC AXLE JACK 1 565AKHU HYDRAULIC 1.22 O-RING - 2 REQUIRED UNIT 1.23 O-RING COMPLETE 1.24 TEFLON O-RING 2 REQUIRED 1.3 EXTENSION SCREW 1.3A SPRING PIN 1.4 SPRING SUPPORT 1.5 SCREW BUSHING 1.6 Y SHAPE SEAL RING 1.7 HEAD

More information

Round Housing with Side Ports

Round Housing with Side Ports Power Steering Steering Control Unit (SCU) Parts and Repair Information 5 Series Steering Control Units 001 Square Housing with Side Ports Round Housing with Side Ports T E L RP Round Housing with End

More information

PLUMBING CARE AND REPAIR

PLUMBING CARE AND REPAIR PLUMBING CARE AND REPAIR No special skills are required for any of the repairs described in this section. Plumbing repairs are seldom dangerous unless leaking water is soaking areas where there are electrical

More information

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,

More information

INSTRUCTIONS FOR USE SAFETY PRINCIPLES, OPERATION AND MAINTENANCE FOR. HYDRAULIC PUMP type HP 03L, 05L, 07L volume 3 l, 5 l, 7 l

INSTRUCTIONS FOR USE SAFETY PRINCIPLES, OPERATION AND MAINTENANCE FOR. HYDRAULIC PUMP type HP 03L, 05L, 07L volume 3 l, 5 l, 7 l BRANO a.s, 747 41 Hradec nad Moravicí Czech Republic tel.:+420/ 553 632 316, 553 632 303 fax:+420/ 553 632 407, 553 632 151 http://www.brano.eu info@brano.eu INSTRUCTIONS FOR USE SAFETY PRINCIPLES, OPERATION

More information

DO NOT attempt to repair hub and wheel bearing assembly.

DO NOT attempt to repair hub and wheel bearing assembly. Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack

More information

CHROME FRONT BRAKE MASTER CYLINDER KIT

CHROME FRONT BRAKE MASTER CYLINDER KIT -J075 REV. 009-0-0 CHROME FRONT BRAKE MASTER CYLINDER KIT GENERAL Kit Number 5-99D, 5-99D Models These Chrome Master Cylinder Kits are designed to replace the original equipment front brake master cylinder

More information

Operating, Installation, and Maintenance Instructions

Operating, Installation, and Maintenance Instructions ELKHART BRASS MFG. CO., INC. 1302 WEST BEARDSLEY AVENUE P.O. BOX 1127 ELKHART IN 46515 (574) 295-8330 FAX (574) 293-9914 Operating, Installation, and Maintenance Instructions RAM Personal Portable Monitor

More information

STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES

STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES GATE VALVE O.S. & Y 1.0 Periodic Inspections 1.1 The valve stem packing should be inspected at least monthly. If the stem packing shows signs of leakage, simply tighten the adjusting nuts to compress the

More information

MEASURING WHEEL ALIGNMENT

MEASURING WHEEL ALIGNMENT MEASURING WHEEL ALIGNMENT 2003-04 WHEEL ALIGNMENT Specifications & Procedures - Hummer - H2 Steering and vibration complaints are not always the result of improper alignment. One possible cause is wheel

More information

Assembly and Usage Instructions

Assembly and Usage Instructions Assembly and Usage Instructions A Product 5885 West Van Horn Tavern Road Columbia, MO 65203 www.caldwellshooting.com Instruction #1001667 Limited Warranty Every Caldwell product is warrantied to be free

More information

INSPECTION, MAINTENANCE AND RECHARGE SERVICE MANUAL P/N 16303

INSPECTION, MAINTENANCE AND RECHARGE SERVICE MANUAL P/N 16303 WATER MIST HAND PORTABLE FIRE EXTINGUISHERS Model B270 ¾ Gallon Model B272 2 ½ Gallon INSPECTION, MAINTENANCE AND RECHARGE SERVICE MANUAL P/N 6303 All fire extinguishers should be installed, inspected

More information

MP-4V Heavy Duty Riveter / 39048

MP-4V Heavy Duty Riveter / 39048 MP-4V Heavy Duty Riveter / 39048 This newly designed heavy-duty air/hydraulic riveter is ergonomically designed with the professional in mind. The light weight 3.7 lbs. well balanced MP-4V includes a Vacuum

More information

Oregon Fuel Injection

Oregon Fuel Injection Corporate Office: P.O. Box 21121, VE Pump Removal and Installation Cummins Lock Timed Applications Removal Clean the exterior of the injection pump and mounting surfaces. 1. Disconnect the fuel return

More information

Installation Instructions

Installation Instructions Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step

More information

CHIPPING HAMMERS. 9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A.

CHIPPING HAMMERS. 9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A. CHIPG HAMMERS Website: www.apt-tools.com e-mail: info@apt-tools.com TDS-1056 Rev A CHIPG HAMMERS TOOL MAINTENANCE & REPAIR INFORMATION FIELD OPERATION: Before use: 1. On 650 Series tools, tighten the handle

More information

Professional Precharged Hunting Rifle

Professional Precharged Hunting Rifle TRIGGER ADJUSTMENT. The trigger is set at the factory, but some aspects can be adjusted to suit individual preferences. 1. This screw adjusts the weight of second stage trigger pull, to increase the weight

More information

2005 MINI Cooper. 2002-05 MANUAL TRANSMISSIONS On-Vehicle Servicing. Cooper S Getrag 285

2005 MINI Cooper. 2002-05 MANUAL TRANSMISSIONS On-Vehicle Servicing. Cooper S Getrag 285 2002-05 MANUAL TRANSMISSIONS On-Vehicle Servicing APPLICATION MANUAL TRANSMISSION APPLICATIONS Application Transmission Model Cooper R65 Cooper S Getrag 285 LUBRICATION SERVICE INTERVALS Inspect fluid

More information

Owner s Manual Read and keep this manual. Patents World Wide

Owner s Manual Read and keep this manual. Patents World Wide Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist

More information

Rating when used as a weight carrying hitch without spring bars:

Rating when used as a weight carrying hitch without spring bars: BOLT-TOGETHER WEIGHT DISTRIBUTING HITCH SYSTEM Rating when used as a weight distributing hitch with spring bars: Part Number 48051 4805 48053 48054 Max Tongue Weight 550 Ibs. 750 Ibs. 1000 Ibs. 1400 lbs.

More information

TUTORIAL. REbUILdING. front CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-1

TUTORIAL. REbUILdING. front CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-1 Part #: HT-1 1965-82 CORVETTE O-RING CONVERSION front CALIpER REbUILdING TUTORIAL Choosing a Brake Caliper Rebuild Kit Standard Lip Seals vs. O-Ring Seals Lip seal design seals are used on 1965-1982 Corvette

More information

EXCAVATOR SAFETY TRAINING

EXCAVATOR SAFETY TRAINING EXCAVATOR SAFETY TRAINING INSPECTION CHECKLIST INSPECTION AREA INSPECTION RESULTS Sat. Unsat. N/A Comments Carrier & Car Body Rotation system Tracks Rollers Frame, welds, bolts Drive system Upper Structure

More information

15GAL STEEL OIL DRAIN WITH 110V PUMP

15GAL STEEL OIL DRAIN WITH 110V PUMP 15GAL STEEL OIL DRAIN WITH 110V PUMP OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

Operating Instructions Hand pallet trucks HU Profi. Issue 08.2000

Operating Instructions Hand pallet trucks HU Profi. Issue 08.2000 Operating Instructions Hand pallet trucks HU Profi Issue 08.2000 Index 1 Introduction 1.1 Product description 1.2 General information on service and maintenance 1.3 Spare parts 1.4 Dimensions 2 Correct

More information

Class 5 to 7 Truck and Bus Hydraulic Brake System

Class 5 to 7 Truck and Bus Hydraulic Brake System Class 5 to 7 Truck and Bus Hydraulic Brake System Diagnostic Guide 1st Edition * 5+0 Important Service tes The information in this publication was current at the time of printing. The information presented

More information

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER 14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------

More information

BETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS

BETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS BETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS PART NUMBER: 132581 REVISION: A RELEASE DATE: 24 March 2000 Page 1 of 10

More information

Before repairing your toilet, you must determine

Before repairing your toilet, you must determine Before repairing your toilet, you must determine which type of toilet you have. Pressurized Toilets If you have a pressurized toilet, it is recommended that you call a licensed plumbing contractor to repair

More information

BACKPACK SPRAYERS. MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12

BACKPACK SPRAYERS. MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12 BACKPACK SPRAYERS MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12 INTRODUCTION Thank you for purchasing this CLARKE Sprayer, designed for use only with

More information

2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13)

2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13) 2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13) Exploded View Special Tools Required Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool 07GAF-SD40100 Bearing driver attachment,

More information

Hydraulic Air Riveter. Operation Manual RC197 RC198. Recommend for mass production line industrial area. Page 1

Hydraulic Air Riveter. Operation Manual RC197 RC198. Recommend for mass production line industrial area. Page 1 Hydraulic Air Riveter Recommend for mass production line industrial area Operation Manual RC197 RC198 Page 1 CONTENTS 1 Important Safety Rules 2 Tool Specification 2.1 Nomenclature 2.2 Technical Data 3

More information

OPERATING INSTRUCTION MANUAL FOR S-240 HYDRAULIC CUTTERS WITH PARTS LIST

OPERATING INSTRUCTION MANUAL FOR S-240 HYDRAULIC CUTTERS WITH PARTS LIST HUSKIE TOOLS, INC. OPERATING INSTRUCTION MANUAL FOR S-240 HYDRAULIC CUTTERS WITH PARTS LIST GENERAL INFORMATION GUIDE FOR S-240 CUTTER The following steps are guidelines for safe operation of the Huskie

More information

Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation

Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...

More information

INGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT

INGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT D. L. Martin Company INGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT TYPICAL HYDRAULIC JACK HEAD ASSEMBLY 1 TOOLS REQUIRED: 1) Container to hold hydraulic fluid. 2) Clean rags and protective covers

More information

VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS

VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS Tools required: 10mm/13mm socket and 3/8 drive ratchet with extension Torx T20/25/30 screwdrivers or bits Phillips head screwdriver,

More information

2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net

2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.

More information

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations

More information

Operation of the overrun braking system.

Operation of the overrun braking system. Operation of the overrun braking system. Fig 1 The overrun device can be described as the control device of the overrun brake system. A draw-bar force is produced at the coupling point by reducing the

More information

TIPPMANN. A-5 Owner s Manual CO2 POWERED PAINTBALL MARKER

TIPPMANN. A-5 Owner s Manual CO2 POWERED PAINTBALL MARKER TIPPMANN PNEUMATICS, INC. Get Your ur Heart t Pound unding With h A Tippmann! WARNING: This paintball marker/gun is not a toy nor is it intended for unsupervised use by persons under the age of 18 years.

More information

Steering column, steering column tube and steering wheel, servicing

Steering column, steering column tube and steering wheel, servicing 48-1 Steering column, steering column tube and steering wheel, servicing Airbag functional check and airbag On Board Diagnostic (OBD) program Repair Manual, Body-Exterior, Body- Interior, Repair Group

More information

TUTORIAL. REbUILdING. REAR CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-2

TUTORIAL. REbUILdING. REAR CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-2 Part #: HT-2 1965-82 CORVETTE O-RING CONVERSION REAR CALIpER REbUILdING TUTORIAL Choosing a Brake Caliper Rebuild Kit Standard Lip Seals vs. O-Ring Seals Lip seal design seals are used on 1965-1982 Corvette

More information

Fuel Injection Pump, Rotary (005-014)

Fuel Injection Pump, Rotary (005-014) Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train

More information

Auxiliary Rams USERS MANUAL

Auxiliary Rams USERS MANUAL Auxiliary Rams 2007 Chief Automotive Technologies, Inc. Chief s Limited One-Year Warranty & Liability CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies, Inc. warrants for one

More information

HAIR CLIPPER. Model No. HC5150 HC5150 2. 3.

HAIR CLIPPER. Model No. HC5150 HC5150 2. 3. All technical modifications reserved. 09/08. TSC 08.0634 HAIR CLIPPER 2. 3. 1. Model No. HC5150 4. 10/UK/HC5150 Version 03/10 Part No. T22-29458 REMINGTON is a Registered Trade Mark of Spectrum Brands,

More information

Installation, Maintenance, & Repair Series 4000B/LF4000B

Installation, Maintenance, & Repair Series 4000B/LF4000B Installation, Maintenance, & Repair Series 4000B/LF4000B Reduced Pressure Zone Assemblies Sizes: 1 2" 2" (15 50mm) RP/IS-A-4000B 4000B/LF4000B Size: 3 /4"! WARNING Testing Read this Manual BEFORE using

More information

INTERLIFT ILR OWNERS MANUAL. INTERLIFT, INC. a member of MBB. 15939 Piuma Ave., Cerritos, CA 90703 Tel (888)-774-5844 Fax (562) 924-8318

INTERLIFT ILR OWNERS MANUAL. INTERLIFT, INC. a member of MBB. 15939 Piuma Ave., Cerritos, CA 90703 Tel (888)-774-5844 Fax (562) 924-8318 INTERLIFT ILR OWNERS MANUAL INTERLIFT, INC. a member of MBB 15939 Piuma Ave., Cerritos, CA 90703 Tel (888)-774-5844 Fax (562) 924-8318 1 TABLE OF CONTENT PAGE TECHNICAL DESCRIPTION 3 GENERAL INFORMATION

More information

Roll-Up Door Maintenance Guide

Roll-Up Door Maintenance Guide R Roll-Up Door Maintenance Guide Cable Replacement on Two Spring Type Balancer Page 1 Panel Replacement - Removable Roller Cover Type Bottom Panel Page 1 Panel Replacement - Removable Roller Cover Type

More information

Auto-belay Cable Replacement Process

Auto-belay Cable Replacement Process Auto-belay Cable Replacement Process Version 2.00 WARNING: The air pressure in the auto-belay system is what causes the cable to be retracted when releasing the cable or climbing the wall with the cable

More information

Hydraulic Transmission Jacks Operating Instructions & Parts Manual

Hydraulic Transmission Jacks Operating Instructions & Parts Manual Blackhawk Automotive is a Licensed Trade Mark Made by SFA Companies, Kansas City, MO Hydraulic Transmission Jacks Operating Instructions & Parts Manual Model BH7011 BH7210 Capacity 1/2 Ton 1 Ton SFA Companies

More information

Installation and User Instructions Unvented Electric Storage Water Heater Models: S10UNV, S15UNV.

Installation and User Instructions Unvented Electric Storage Water Heater Models: S10UNV, S15UNV. Installation and User Instructions Unvented Electric Storage Water Heater Models: S10UNV, S15UNV. MULTIPOINT Please read and understand these instructions before starting work. Please leave this leaflet

More information