EXPLOSION-PROOF EMERGENCY LIGHTING FIXTURE FOR FLUORESCENT LAMP EVF-..-EL SERIES Gas explosion protection II 2G Ex d IIC T6 Gb (suitable for Zone1 and Zone 2) Dust explosion protection II 2D Ex tb IIIC T80 C Db IP66 (suitable for Zone 21 and Zone 22) EC-Type Examination Certificate LCIE 14 ATEX 3038X Certificate of Conformity IECEx LCIE 14.0029X Conformity to standards EN 60079-0 ; EN 60079-1 ; EN 60079-31 IEC 60079-0 ; IEC 60079-1 ; IEC 60079-31 Material : Enclosure Copper-free aluminium, powder coated surface yellow colour RAL 1021 Glass tube Toughened glass Wire guard (optional) Powder coated carbon steel (white) or stainless steel Exposed fastener Stainless steel Emergency unit Ballast Lamp specification Special emergency controller and Ni-Mh battery pack with protection against over charge and over discharge. Electronic ballast, wide voltage range, rapid starting, stable performance, power factor 0.95. End of lamp life (EOL) rectification effect protection. Fluorescent tubular lamp T8 (supplied with the lighting fixture). Lamp power 18W x 2 ; 36W x 2 ; 58W x 2 Emergency power 18W x 1 ; 36W x 1 ; 58W x 1 Charge time Emergency lighting time 24 h 120 min (180 min as option)
Rated voltage Degree of protection Ambient temperature Earthing protection Terminals Mounting Cable entries 100 300V 50/60Hz IP66-20 C to +55 C M5 (internal and external earth bolts) 3 x 1,5 4 sqmm (L+N+PE) Ceiling type ; pole type ; pendant type 2 x M25 Selection Table Type Lamp power (W) Weight (Kg) Type Lamp power (W) Weight (Kg) EVF-18 x 2-ELC 18 x 2 14.50 EVF-18 x 2-ELP 18 x 2 14.60 EVF-36 x 2-ELC 36 x 2 20.20 EVF-36 x 2-ELP 36 x 2 20.30 EVF-58 x 2-ELC 58 x 2 22.20 EVF-58 x 2-ELP 58 x 2 22.30 C = Ceiling Mounting Type P = Pole Mounting Type Dimensional drawings (all dimensions in mm)
EVF-..x2-ELC explosion-proof emergency light fittings for fluorescent lamp (Ceiling type) EVF-..-x2-ELP explosion-proof emergency light fittings for fluorescent lamp (pole type)
EXPLOSION-PROOF LED LIGHTING FIXTURE EVF-LED.. SERIES Gas explosion protection II 2G Ex d IIC T6 Gb (suitable for Zone1 and Zone 2) Dust explosion protection II 2D Ex tb IIIC T80 C Db IP66 (suitable for Zone 21 and Zone 22) EC-Type Examination Certificate LCIE 14 ATEX 3017X Certificate of Conformity IECEx LCIE 14.0025X Conformity to standards EN 60079-0 ; EN 60079-1 ; EN 60079-31 IEC 60079-0 ; IEC 60079-1 ; IEC 60079-31 Material : Enclosure Copper-free aluminium, powder coated surface yellow colour RAL 1021 Glass tube Toughened glass Wire guard (optional) Powder coated carbon steel (white) or stainless steel Exposed fastener Stainless steel Power controller Lamp specification Wide voltage input, CC-CV (constant current constant voltage) output, power factor 0.98, with function of distributed current, constant current, surge-proof and anti-electromagnetic interference, protection against overcurrent, open circuit and short circuit. CREE plural white LED modules Lamp power 9W x 1 ; 9W x 2 ; 18W x 1 ; 18W x 2 Rated voltage Degree of protection Ambient temperature Earthing protection Terminals 110 265V 50/60Hz IP66-40 C to +55 C M5 (internal and external earth bolts) 3 x 1,5 4 sqmm (L+N+PE)
Mounting Cable entries Ceiling type ; pole type 2 x M25 Selection Table Type Lamp power (W) Weight (Kg) Type Lamp power (W) Weight (Kg) EVF-LED 9 x 1C 9 x 1 5.50 EVF-LED 18 x 1C 18 x 1 8.30 EVF-LED 9 x 1P 9 x 1 5.90 EVF-LED 18 x 1P 18 x 1 8.70 EVF-LED 9 x 2C 9 x 2 9.80 EVF-LED 18 x 2C 18 x 2 15.70 EVF-LED 9 x 2P 9 x 2 10.50 EVF-LED 18 x 2P 18 x 2 16.40 C= Ceiling Mounting Type P=Pole Mounting Type
Advantages of LED lights LED lights bring several advantages such as energy efficiency, durability, long lifespan, no UV emissions, no flicker and dramatically reduced maintenance requirements. This translates into energy savings, maintenance savings and an overall reduction in cost of ownership over the product's lifetime. The benefits of LED lighting are endless. LED lights are energy efficient, cost effective, durable and more. They are the latest technology in lighting and offer a great alternative in replacing your current standard lights. The operational life of current white LED lights is 60000 hours at constant light output. The long operational life of a LED light is a stark contrast to the average life of a fluorescent lamp, which is approximately 7000-8000 hours. If the lighting fixture needs to be embedded into a very inaccessible place, using LEDs would virtually eliminate the need for routine fluorescent lamp replacement. There is no comparison between the cost of LED lights vs. traditional fluorescent lamp options. With fluorescent lamp, the true cost of the lamp is the cost of replacement lamps and the labor expense and time needed to replace them. These are significant factors, especially where there are a large number of installed lamps. The maintenance costs to replace fluorescent lamps can be enormous. These issues can all be virtually eliminated with the LED option. The key strength of LED light is luminous efficacy >90 lm/w, reduced power consumption, single-direction illumination, uniform and soft light, high colour render, low heat dissipation. Environmentally friendly The benefit of LED lights is that they are an eco-friendly form of lighting as they do not contain mercury or other harmful gasses or emit any harmful UV rays. Fast Switching LED lights will start at full brightness, instantly, every time therefore there is no need for backup lighting. LED lights are a benefit because they switch on and off instantly compared to standard fluorescent lamps which fade in and out or flicker. Improved Durability LED's have no filaments so can withstand a greater intensity of vibration and shock than standard lights making them durable with less risk of breaking and need to replace.
EXPLOSION-PROOF LIGHTING FIXTURE FOR FLUORESCENT LAMP EVF-.. SERIES Gas explosion protection II 2G Ex d IIC T6 Gb (suitable for Zone1 and Zone 2) Dust explosion protection II 2D Ex tb IIIC T80 C Db IP66 (suitable for Zone 21 and Zone 22) EC-Type Examination Certificate LCIE 14 ATEX 3037X Certificate of Conformity IECEx LCIE 14.0027X Conformity to standards EN 60079-0 ; EN 60079-1 ; EN 60079-31 IEC 60079-0 ; IEC 60079-1 ; IEC 60079-31 Material : Enclosure Copper-free aluminium, powder coated surface yellow colour RAL 1021 Glass tube Toughened glass Wire guard (optional) Powder coated carbon steel (white) or stainless steel Exposed fastener Stainless steel Ballast Lamp specification Electronic ballast, wide voltage range, rapid starting, stable performance, power factor 0.95. End of lamp life (EOL) rectification effect protection. Fluorescent tubular lamp T8 (supplied with the lighting fixture). Lamp power 18W x 1 ; 18W x 2 ; 36W x 1 ; 36W x 2 ; 58W x 1 ; 58W x 2 Rated voltage Degree of protection Ambient temperature Earthing protection Terminals 100 300V 50/60Hz IP66-20 C to +55 C M5 (internal and external earth bolts) 3 x 1,5 4 sqmm (L+N+PE)
Mounting Cable entries Ceiling type ; pole type ; pendant type 2 x M25 Selection Table Type Lamp power (W) Weight (Kg) Type Lamp power (W) Weight (Kg) EVF - 18 x 1C 18 x 1 5.60 EVF - 18 x 2C 18 x 2 10.60 EVF - 18 x 1P 18 x 1 6.50 EVF - 18 x 2P 18 x 2 11.55 EVF - 36 x 1C 36 x 1 8.80 EVF - 36 x 2C 36 x 2 16.30 EVF - 36 x 1P 36 x 1 9.30 EVF - 36 x 2P 36 x 2 16.85 EVF - 58 x 1C 58 x 1 10.40 EVF - 58 x 2C 58 x 2 18.30 EVF - 58 x 1P 58 x 1 10.85 EVF - 58 x 2P 58 x 2 19.20 C = Ceiling Mounting Type P = Pole Mounting Type Dimensional drawings (all dimensions in mm) SINGLE LAMP DUAL LAMP