Inductive slot sensor

Size: px

Start display at page:

Download "Inductive slot sensor"

Laurence Edwards
7 years ago
Views:

1 0102 Model Number Features 3.5 mm slot width Usable up to SIL 3 acc. to IEC Extended temperature range Application Danger! In safety-related applications the sensor must be operated with a qualified fail safe interface from Pepperl+Fuchs, such as KFD2-SH-EX1. Consider the "exida Functional Safety Assessment" document which is available on as an integral part of this product s documentation. Technical Data specifications Switching element function NAMUR, NC Slot width 3.5 mm Depth of immersion (lateral) typ. 6 mm Installation Output polarity Safety Function Nominal ratings Nominal voltage U o 8 V Switching frequency f Hz Hysteresis H with NAMUR switch amplifier: mm (e. g. Pepperl+Fuchs KCD2-SR-Ex1.LB) with safety switch amplifier mm (e. g. Pepperl+Fuchs KFD2- SH-Ex1) Suitable for 2:1 technology yes, with reverse polarity protection diode Rate of current rise -4.5 ma / mm Current consumption Measuring plate not detected 3 ma Measuring plate detected 1 ma Functional safety related parameters MTTF d 7970 a Mission Time (T M ) 20 a Diagnostic Coverage (DC) 0 % Ambient conditions Ambient temperature C ( F) Safety application: C Mechanical specifications Connection type flexible leads LiY, 500 mm Core cross-section 0.14 mm 2 Housing material PBT Degree of protection Note IP67 adjustable stop Security relevant only up to -40 C information Use in the hazardous area see instruction manuals Category 1G; 2G; 3G; 1D Compliance with standards and directives Standard conformity NAMUR EN :2000 IEC :1999 Standards EN :2007 IEC :2007 Approvals and certificates FM approval Control drawing UL approval culus Listed, Purpose CSA approval ccsaus Listed, Purpose CCC approval CCC approval / marking not required for products rated 36 V Dimensions Electrical Connection 10 BN BU ø 1.85 L+ L- 3 1

Consider the "exida Functional Safety Assessment" document which is available on www.pepperl-fuchs.com as an integral part of this product s documentation.

2 ATEX 1G Device category 1G II 1G Ex ia IIC T6 T1 Ga Ignition protection "Intrinsic safety" µh ; a cable length of 10 m is considered. and in this instruction manual. The has to be observed. The special conditions must be adhered to! Directive 94/9/EC and therefore the EC-type-examination certificates generally apply only to the use of electrical apparatus under atmospheric conditions. Ambient temperature ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate. Note: Use the temperature table for category 1!!! The 20 % reduction in accordance with EN has already been applied to the temperature table for category 1. related apparatus and according to the proof of intrinsic safety. The associated apparatus must satisfy the requirements of category ia. Because of the risk of ignition, which can occur due to faults and/or transient currents in the equipotential bonding system, galvanic isolation is preferable in the supply and signal circuits. Associated apparatus without electrical isolation can only be used if the corresponding requirements of IEC are satisfied. Install the device in such a way that the resin surface is not exposed to mechanical hazards. If the Ex-related marking is printed only on the supplied label, then this must be attached in the immediate vicinity of the sensor. The sticking surface for the label must be clean and free from grease. The attached label must be legible and indelible, including in the event of possible chemical corrosion. 2

Ambient temperature ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate.

3 ATEX 2G Device category 2G II 1G Ex ia IIC T6 T1 Ga Ignition protection "Intrinsic safety" µh ; a cable length of 10 m is considered. and in this instruction manual. The has to be observed. The special conditions must be adhered to! Directive 94/9/EC and therefore the EC-type-examination certificates generally apply only to the use of electrical apparatus under atmospheric conditions. Maximum permissible ambient temperature T amb ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate. related apparatus and according to the proof of intrinsic safety. Install the device in such a way that the resin surface is not exposed to mechanical hazards. If the Ex-related marking is printed only on the supplied label, then this must be attached in the immediate vicinity of the sensor. The sticking surface for the label must be clean and free from grease. The attached label must be legible and indelible, including in the event of possible chemical corrosion. 3

Maximum permissible ambient temperature T amb ambient temperature, the temperature class, and the effective internal reactance values can be found on the EC-type examination certificate.

4 ATEX 3G (ic) Device category 3G (ic) Certificate of Compliance CE marking PF 13CERT2895 X II 3G Ex ic IIC T6 T1 Gc Ignition protection category "ic" 30 nf ; A cable length of 10 m is considered. for Pi=34 mw, Ii=25 ma, T6 for Pi=34 mw, Ii=25 ma, T5 for Pi=34 mw, Ii=25 ma, T4-T1 for Pi=64 mw, Ii=25 ma, T6 for Pi=64 mw, Ii=25 ma, T5 for Pi=64 mw, Ii=25 ma, T4-T1 for Pi=169 mw, Ii=52 ma, T6 for Pi=169 mw, Ii=52 ma, T5 for Pi=169 mw, Ii=52 ma, T4-T1 for Pi=242 mw, Ii=76 ma, T6 for Pi=242 mw, Ii=76 ma, T5 for Pi=242 mw, Ii=76 ma, T4-T1 Connection parts 100 µh ; A cable length of 10 m is considered. and in this instruction manual. The data stated in the data sheet are restricted by this operating instruction! The special conditions must be observed! must be observed. The sensor must only be operated with energy-limited circuits, which satisfy the requirements of IEC The explosion group complies with the connected, supplying, power limiting circuit. Install the device in such a way that the resin surface is not exposed to mechanical hazards. If the Ex-relevant identification is printed exclusively on the adhesive label provided, this label must be affixed in the immediate vicinity of the sensor! The background surface to which the adhesivelabel is to be applied must be clean and free from grease! The applied label must be durable and remain legible, with due consideration of the possibility of chemical corrosion! 70 C (158 F) 85 C (185 F) 100 C (212 F) 66 C (150.8 F) 81 C (177.8 F) 100 C (212 F) 45 C (113 F) 60 C (140 F) 89 C (192.2 F) 30 C (86 F) 45 C (113 F) 74 C (165.2 F) The sensor must not be mechanically damaged. When used in the temperature range below -20 C the sensor should be protected from knocks by the provision of an additional housing. The connection parts are to be installed, such that a minimum protection class of IP20 is achieved, in accordance with IEC

Pi=169 mw, Ii=52 ma, T5 for Pi=169 mw, Ii=52 ma, T4-T1 for Pi=242 mw, Ii=76 ma, T6 for Pi=242 mw, Ii=76 ma, T5 for Pi=242 mw, Ii=76 ma, T4-T1 Connection parts 100 µh ; A cable length of 10 m is

5 ATEX 1D Device category 1D for use in hazardous areas with combustible dust II 1D Ex ia IIIC T135 C Da Ignition protection "Intrinsic safety" µh A cable length of 10 m is considered. Permissible ambient temperature range and in this instruction manual. The has to be observed. Directive 94/9/EC and therefore the EC-type-examination certificates generally apply only to the use of electrical apparatus under atmospheric conditions. ambient temperature, the surface temperature, and the effective internal reactance values can be found on the EC-type-examination certificate. The maximum permissible ambient temperature of the data sheet must be noted, in addition, the lower of the two values must be maintained. related apparatus and according to the proof of intrinsic safety. If the Ex-related marking is printed only on the supplied label, then this must be attached in the immediate vicinity of the sensor. The sticking surface for the label must be clean and free from grease. The attached label must be legible and indelible, including in the event of possible chemical corrosion. Electrostatic charge Avoid electrostatic charges that can cause electrostatic discharge when installing or operating the device. Information on electrostatic hazards can be found in the technical specification IEC/TS Do not attach the nameplate provided in areas where electrostatic charge can build up. 5

Directive 94/9/EC and therefore the EC-type-examination certificates generally apply only to the use of electrical apparatus under atmospheric conditions.

Technical Data. General specifications Switching element function Rated operating distance s n 4 mm

Technical Data. General specifications Switching element function Rated operating distance s n 4 mm 0102 Model Number Features 4 mm non-flush Usable up to SIL 3 acc. to IEC 61508 Application Danger! In safety-related applications the sensor must be operated with a qualified fail safe interface from Pepperl+Fuchs,