Power Relay FEATURES Small package design ARC barrier equipped Silver Cadium Oxide contact High dielectric strength (,800 Vac) High reliability and long life Ultra-high sensitivity with quick response time ( ms max.) High vibration and shock resistance Options include LED indicator, diode protection, and LED indicator/diode protection UL listed, CE certified, CSA certified TYPICAL APPLICATIONS Control panels Elevator panels Machine tools Test equipment general-purpose power relays are designed for a wide range of applications including power as well as logic control for factory machines and control panels. relays break 0 A loads and are ideal for control panels that require stable and reliable relays. One standard and three options are available: LED indicator, internal surge protection diode, and LED indicator/diode protection. Honeywell s global sales and distribution channels ensure a rapid response and excellent customer service. WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. WARNING MISUSE OF DOCUMENTATION The information presented in this product sheet is for reference only. Do not use this document as a product installation guide. Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury. Sensing and Control
RELAY MODEL SELECTION GUIDE Type Terminal Contact Catalog Listing Standard Plug-in/Solder PCB DPDT PDT DPDT PDT SZR-LY- SZR-LY- SZR-LY-P SZR-LY-P LED Indicator Plug-in/Solder DPDT SZR-LY-N PDT SZR-LY-N DIODE surge suppression DPDT SZR-LY-D PDT SZR-LY-D LED indicator + surge suppression DPDT SZR-LY-X PDT SZR-LY-X SOCKETS REQUIRED ACCESSORIES Din-rail Mounting Solder Terminal PCB Terminal Relay Contact DPDT For use with SZR-LY-, - N, -D, -X PDT For use with SZR-LY-, - N, -D, -X SZX-SLF-08N SZX-SLB-08 SZX-SLB-08P SZX-SLF- SZX-SLB- SZX-SLB-P CONTACT RATINGS Ratings Rated load Load Resistive Load (p.f. = ) 0 Vac, 0 A Vdc, 0 A Inductive load (p.f. = 0., L/R = 7 ms) 0 Vac, 7. A Vdc, A Carry current 0 A Max. operating voltage 0 Vac, Vdc Max. operating current 0 A Max. switching capacity,00 VA, 0 W 8 VA, 0 W Min. permissible load Vdc, 00 ma Honeywell Sensing and Control
COIL RATINGS (DPDT) Rated Current (ma) Rated 0 Hz 0 Hz Coil resistance (Ω) Coil Inductance (H) Armature OFF Armature ON Pick-up Dropout Maximum Power Consumption (W). 8. 0.0 0.08 Approx. 0. 9 0.7 0..0 W to. W.8 80 0.9. Max. Min. (0 Hz) AC 0.7 788.. 80 % 0% 0% 00/0.7/.9 0/,70.. Approx 0/0 9.9/0.8 8./9.,0 9.. 0.9 W to. W 00/0./.8./.8,90.7 9.07 (0 Hz) 0/0.8/../. 8,790 8.. 0 0 0.7 0. 7 0 0.7.7 Max. Min. Approx. DC.9 0..7 80% 0% 0% 0.9 W 8 8.,00 0..0 00/0 9./0,000. 8. COIL RATINGS (PDT) Rated Current (ma) Rated 0 Hz 0 Hz Coil resistance (Ω) Coil Inductance (H) Armature OFF Armature ON Pick-up Dropout Maximum Power Consumption (W) 8 0 0.0 0.0 99 70 0 0. 0.7 Approx. 9. 80 78 0.8 0.7 Max. Min..9 W to. W AC 0.8 0 0.7.88 80 % 0% 0% (0 Hz) 00/0./. 9/.8,800 0. 7. 00/0./. 9.8/.,700. 7.9 0 0.09 0. 0 00 0.9 0.8 Max. Min. Approx. DC 9 0..9 80% 0% 0%. W 8 0,00.9. 00/0 /.9,900.7 Note : The rated current and coil resistance are measured at a coil temperature of C [7. F] with tolerances of +%, -0% for AC rated current and ± % for DC coil resistance. Note : The rated current of N and X types is ma higher than the value in the table above. Honeywell Sensing and Control
SPECIFICATIONS Contact material Silver Cadium Oxide Contact resistance Max. 0 MOhm Operate time Max. ms Release time Max. ms Operating Mechanical 8,000 operations per hour frequency Electrical,800 operations per hour Insulation resistance Min. 00 Mw at 00 Vdc Dielectric withstand voltage,800 Vac 0 Hz/0 Hz for one minute between non-continuous current carrying terminals and between coil thermals and contact terminals,000 Vac 0/0 Hz for minute between contacts of same polarity Vibration Mechanical durability 0 Hz to Hz at double amplitude of.0 mm resistance Malfunction durability 0 Hz to Hz at double amplitude of.0 mm Shock resistance Mechanical durability,000 m/s (approx. 00 g) Malfunction durability 00 m/s (approx. 0 g) Service life Mechanical AC: Min. 0 million operations (at operating frequency of 8,000 operations/hour) DC: Min. 00 million operations (at operating frequency of 8,000 operations/hour) Electrical DPDT: Min. 00,000 operations (at operating frequency of,800 operations/hour) PDT: Min. 00,000 operations (at operating frequency of,800 operations/hour) Weight DPDT: Approximately g PDT: Approximately g Note : The data shown above are of initial value CHARACTERISTIC DATA Max. Switching capacity Electrical life DPDT Rated operating current(a) 0 DC resistive 0. 0. DC inductive L/R=7ms AC inductive p.f.=0. AC resistive Number of operations( 0 ),000 00 00 0 0 DCV (L/R=7ms) DCV resistive load AC0V resistive load AC0V (cosf =0.) 0 0 00 00 Rated operating voltage 0 8 0 Current(A) Max. Switching capacity Electrical life PDT Rated operating current(a) 0 DC resistive 0. 0. DC inductive L/R=7ms AC inductive p.f.=0. AC resistive 0 0 00 00 Rated operating voltage Number of operations( 0 ),000 00 00 0 0 DCV resistive load DCV (L/R=7ms) AC0V (cosf =0.) AC0V resistive load 0 8 0 Current(A) Honeywell Sensing and Control
CATALOG LISTING MATRIX SZR LY P AC0-0V Amp Rating: MY = A or A LY = 0 A Product Type General Purpose Relay Poles = DPDT = PDT Mounting Type = Terminal Option Type = No Indicator or Diode D = Internal Surge Protection Diode N = Red LED Operation Indicator X = LED and Diode Terminal Type = Solder/Plug-in P = PCB Rating: ACV = Vac ACV = Vac ACV = Vac AC0V = 0 Vac AC00V = 00 Vac AC0-0V = 0/0 Vac AC00V = 00 Vac AC0V = 0 Vac AC0-0V = 0/0 Vac * DCV = Vdc DCV = Vdc DCV = Vdc DC8V = 8 Vdc DC00V = 00 Vdc 0 Vac - Submitted for UL approval Honeywell Sensing and Control
HOLDING CLIPS Holding clips are included with the sockets Holding clips for the SLF-08N cannot be removed once inserted The holding clip for the SLF- can be removed by pushing the side of the inserting hold with a sharp object Holding clips for all SMB sockets are wire for easy removal Holding clips are to be inserted into the slots provided on the socket DIMENSIONS (For reference only mm/in) Figure. Dimensions For SZX-SLF- sockets, [0.8] Figure. Dimensions For all SZX-SLB sockets 9,0 [.],0 [0.], [0.8],0 [0.87],0 [0.], [.79] 7,0 [0.8] 9, [.] Figure. Dimensions For SZX-SLF-08N sockets, [0.],0 [0.0], [0.09], [0.7], [0.8] 9,9 [.9], [0.] Honeywell Sensing and Control
FIGURE. DIMENSION, CIRCUIT DIAGRAM, TERMINAL ARRANGEMENT, AND MOUNTING HOLE FOR SZR-LY-, SZR-LY-N, SZR-LY-D, and SZR-LY-X 0, [0.0] - O,0 [0.],0 [0.0],7 [0.] Max. 8,0 [.0],0 [0.] Max.,0 [.], [0.] Max., [0.8] LY- LY-N AC LY-N DC LY-D LY-X 7 8 7 8 - + 7 8 - + 7 8 - + 7 8 Bottom view FIGURE. DIMENSION, CIRCUIT DIAGRAM, TERMINAL ARRANGEMENT, AND MOUNTING HOLE FOR SZR-MY-P and SZR-MY-P,0 [0.08],7 [0.] Max. 8,0 [.0] 0, [0.0] Max.,0 [.],0 [0.0], [0.8] Max., [0.8] The circuit diagram is the same wit standard type of SZR-MY- or the SZR-MY- Honeywell Sensing and Control 7
FIGURE. DIMENSION, CIRCUIT DIAGRAM, TERMINAL ARRANGEMENT, AND MOUNTING HOLE FOR SZR-LY-, SZR-LY-N, SZR-LY-D, and SZR-LY-X 0, [0.0] - O.0 Holes,0 [0.0] Max. 8,0 [.0] Max.,0 [.] LY-,0 [0.], [0.] LY-N AC Max., [.] LY-N DC 7 8 7 8 7 8 9 0 9 0 9 0 - + LY-D LY-X 7 8 7 8 9 0 - + 9 0 - + Bottom view FIGURE 7. CIRCUIT DRAWING FOR SZR-LY- and SZR-LY- DPDT-. 0. PDT. 0 0 0 0... 8-. 0.. 7... 8 Honeywell Sensing and Control
Max., [.00] Max. 9, [.] General Purpose SOCKETS FIGURE 8. SZX-SLF-08N FIGURE 9. SZX-SLF-,0 [0.87] 8,0 [0.] 9,0 [0.7],0 ± 0, [0.99 ±.008], [0.8] - O,0 [0.] 7,0 [0.8] -M.x8, [0.] -M,0 ± 0, [. ± 0.008] 7,0 [.], [0.7] 7,0 [.8] - M - O, [0.8] Holes Max. 78, [.09] 8,0 [.8], [.0] 9,0 ± 0, [.7 ± 0.0], [0.0],0 [.0] 0,0 [.8], [0.7],0 [0.99] Max., [.79] 8,0 [0.] Max. 0,0 [.8] Max.,0 [.0] Max.,0 [.0] FIGURE 0. SZX-SLB-08 FIGURE. SZX-SLB- 0, [0.0] Max.,0 [0.9] - O,7 [0.07] Holes,7 [0.] Max. 0, [0.8],0 [0.0] 8 - O,7 [0.07] 8, [.],8 ± 0, [.0 ±.008],7 [0.] Max. 0, [0.8],0 [0.0] Max., [.0] Max. 9, [.] Max., [.7] Max., ± 0, [0.8 ±.008] 8, [.], ± 0, [.0 ± 0.0],0 ± 0, [. ± 0.008] Honeywell Sensing and Control 9
FIGURE. SZX-SLB-08P FIGURE. SZX-SLB-P,7 [0.] Max., [0.] 0, [0.0] Max.,0 [0.9] Max., [.00] Max. 9, [.], [0.8],0 [0.0] 0, [0.0] Max., [.7],0 [0.0], [0.8],0 [0.08] 8, [.],0 [0.0], [0.] 0,0 [0.9], [0.], [0.8], [0.0],7 [0.] Max., [0.],0 [0.08],0 [0.0] Max., [.0] Max. 9, [.] 7, [0.7], [0.],0 [0.],8 [0.], [0.] 8 - O,0 [0.08] Holes 8, [.], [0.0] 0,0 [0.9] 0,0 [.8], [0.] - O,0 [0.08] Holes WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. For application assistance, current specifications, or name of the nearest Authorized Distributor, contact a nearby sales office. Or call: -800-7-9 USA/Canada -8--87 International FAX -8-- USA INTERNET www.honeywell.com/sensing info.sc@honeywell.com Sensing and Control www.honeywell.com/sensing Honeywell West Spring Street Freeport, Illinois 0 009--EN IL0 GLO 00 Printed in USA Copyright 00-00 Honeywell International Inc. All Rights Reserved.