Corning offers the most complete line of connectors and factory-terminated cables, from single-fiber jumpers to high-fiber-count assemblies. As the industry s leading supplier of cable assemblies, Corning s state-of-the-art manufacturing process ensures unsurpassed connector performance with products that meet or exceed all industry standards for reflectance and insertion loss. Highly trained and qualified associates thoroughly inspect the incoming fibers and ferrules, assemble and polish them using a carefully monitored and controlled process. The assemblies undergo rigorous performance testing to ensure optimal quality in every connector. Corning s preterminated assemblies use only high-quality Corning optical fibers to ensure total performance quality. ST Compatible Ultra PC 12-Fiber Cable Assembly Photo LAN2784 Pretium EDGE Reverse Polarity Uniboots Photo LAN2217-2218 Page 1 Revision date 2014-12-14
Specifications Page 2 Revision date 2014-12-14
Cable Assembly Ordering Matrix Corning patch cords and high-fiber-count assemblies are ordered using five easy steps. The steps involve the selection of connector(s), fiber count, fiber type, cable, length and unit of measure. The format/steps are listed below. Note: Begin with smallest connector code. Ordering Information Notes: 1) Select connector code based on type of adapter used at the patch panel and the electronic interface connector. Always use the lowest code first when constructing the part number. 2) Available on 1.6, 2.0 mm and 900 μm cable types only (*). 3) For fiber counts greater than 96, contact a Corning Customer Care Representative. 4) For lengths greater than 999, contact a Corning Customer Care Representative. Page 3 Revision date 2014-12-14
Connector specifications Page 4 Revision date 2014-12-14
Cable Table Page 5 Revision date 2014-12-14
Cable Table (continued) Page 6 Revision date 2014-12-14
Cable Table (continued) Page 7 Revision date 2014-12-14
MT-RJ Jumpers Ordering Information Notes: 1) Select connector code based on type of adapter used at the patch panel and the electronic interface connector. Always use the lowest code first when constructing the part number. 2) MT-RJ patch cords are typically sold without pins. For pinned versions, call a Corning Customer Care Representative. 3) LC available 2.0 mm legs only. If 900 μm or 1.6 mm legs are required, please contact a Corning Customer Care Representative. 4) For hybrid jumpers, standard leg length for single-fiber connector end is 10 in, 2.9 mm legs. For LC, standard leg is 2.0 mm. 5) For lengths greater than 999, contact a Corning Customer Care Representative. Page 8 Revision date 2014-12-14
Part Number Example Part Number Product Description Units per Delivery 025801R2131010F 589802RJ131025M LC Ultra PC Simplex (on first end), SC Ultra PC Simplex (on second end), 1 F, Single-mode (OS2), 2.0 mm riser, 10 ft (assembly length) SC Ultra PC Simplex (on first end), MT-RJ (non-pinned) (on second end), 2 F, Single-mode (OS2), ribbon interconnect riser, 25 m (assembly length) 1/1 1/1 Page 9 Revision date 2014-12-14
Single-Fiber Cable Available in 1.6, 2.0 or 2.9 mm outer diameters. Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Available in riser and plenum. Single-Fiber Cable Drawing ZA-2557 Single-Fiber Cable Drawing ZA-4040 Single-Fiber Cable Drawing ZA-3414 Page 10 Revision date 2014-12-14
Zipcord Cable (2 fibers) Available in 1.6, 2.0 and 2.9 mm subunits. Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Available in riser and plenum. Zipcord Cable (2 fibers) Drawing ZA-2930 Zipcord Cable (2 fibers) Drawing ZA-4041 Zipcord Cable (2 fibers) Drawing ZA-3415 Page 11 Revision date 2014-12-14
DFX Cable (2 fibers) Available in 2.0 or 2.9 mm legs. Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Available in riser and plenum. For total assembly length less than 3 ft, leg lengths are 6 in (+3 in/-0 in). DFX Cable (2 fibers) Drawing ZA-2931 DFX Cable (2 fibers) Drawing ZA-4039 DFX Cable (2 fibers) Drawing ZA-3416 Page 12 Revision date 2014-12-14
Fan-Out Cable (2-24 fibers) Maximum fiber count for fan-out cable assemblies is 24 fibers. Available in 1.6, 2.0 and 2.9 mm subunits. Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Available in riser and plenum. Fan-Out Cable (2-24 fibers) Drawing ZA-2932 Fan-Out Cable (2-24 fibers) Drawing ZA-4042 Fan-Out Cable (2-24 fibers) Drawing ZA-3417 Page 13 Revision date 2014-12-14
MIC Cable Furcation (2-12 fibers) Available in 900 µm, 2.0 and 2.9 mm legs. Heat-shrink furcation for 2.0 and 2.9 mm legs. No furcation for 900 µm legs. Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Available in riser and plenum. Page 14 Revision date 2014-12-14
MIC Cable Furcation (13-24 fibers) Available in 900 µm, 2.0 and 2.9 mm legs. Standard construction of 24-fiber assembly is a single-layer MIC cable. Available in MIC unitized cable construction. A serialized part number is required. Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Page 15 Revision date 2014-12-14
MIC Unitized Cable Furcation (36-144 fibers) Available in 900 µm, 2.0 and 2.9 mm legs. Standard construction is 6-fiber subunit up to 48 fibers and 12-fiber subunit from 60 to 144 fibers. 24-fiber assembly available in MIC unitized cable construction. A serialized part number is required. Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Available in riser and plenum. No heat-shrink furcation on 900 µm. Page 16 Revision date 2014-12-14
Ribbon Interconnect Cable (6-12 Fibers) Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Available in riser and plenum. Legs available in 2.0 mm and 900 µm. Page 17 Revision date 2014-12-14
Ribbon Riser and Plenum Cable (12-72 Fibers) Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. 900 µm legs only Ribbon Riser and Plenum Cable Drawing ZA-2889 Ribbon Riser and Plenum Cable Drawing ZA-4050 Ribbon Riser and Plenum Cable Drawing ZA-4051 Page 18 Revision date 2014-12-14
Ribbon Riser and Plenum Cable (84-216 Fibers) Fiber counts for protective tubes: Tube 1: 1-72 fibers Tube 2: 73-144 fibers Tube 3: 145-216 fibers Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. 900 µm legs only. Legs available in the following lengths: 25, 36, 47 and 72 in. Ribbon Riser and Plenum Cable Drawing ZA-2960 Ribbon Riser and Plenum Cable Drawing ZA-4048 Ribbon Riser and Plenum Cable Drawing ZA-4047 Page 19 Revision date 2014-12-14
ALTOS Outside Plant and FREEDM Cable Available in SMF-28e, SMF-28e XB, 62.5 µm (OM1), 50 µm (OM2, OM3, OM4) fibers. Cable jacket will remain black for single-mode and multimode applications. Available in 12-432 fibers. ALTOS Outside Plant and FREEDM Cable Configuration Drawing ZA-2956 Page 20 Revision date 2014-12-14
Related Products Reference Jumper Kits: Keyed LC Keyed LC Assemblies with non-standard colors ClearCurve Drop Cable Assemblies: Remote Radio Fiber Optic Cable Assemblies OptiFit Node Assembly Reverse Polarity Uniboot Duplex Jumpers Low-Loss Cable Assemblies Ruggedized Zipcord Jumpers FastShip/FastConnect Program: PON Link LAN-1316-EN (http://csmedia.corning.com/opcomm/resource_ Documents/product_family_specifications_rl/LAN-1316-EN.pdf) 0247_NAFTA_AEN (pg 5) (http://csmedia.corning.com/opcomm/ Resource_Documents/product_family_specifications_rl/Security_ Keyed_LC_Connector_Solution_NAFTA_AEN.pdf) LAN-1057-EN (http://csmedia.corning.com/opcomm/resource_ Documents/product_family_specifications_rl/LAN-1057-EN.pdf) 0351_NAFTA_AEN (http://csmedia.corning.com/opcomm/ Resource_Documents/product_family_specifications_rl/ ClearCurve_Drop_Cable_Assemblies_NAFTA_AEN.pdf) CRR-144-AEN (http://csmedia.corning.com/opcomm/resource_ Documents/product_family_specifications_rl/CRR-144-AEN.pdf) EVO-05-EN (http://csmedia.corning.com/opcomm/resource_ Documents/product_family_specifications_rl/OptiFit_Node_ Assembly_NAFTA_AEN.pdf) 0165_NAFTA_AEN (pg 14) (http://csmedia.corning.com/opcomm/ Resource_Documents/product_family_specifications_rl/pretium_ EDGE_HD_solutions_NAFTA_AEN.pdf) 0300_NAFTA_AEN (pg 19) (http://csmedia.corning.com/opcomm/ Resource_Documents/product_family_specifications_rl/Plug_and_ Play_Universal_Systems_NAFTA_AEN.pdf) Contact Corning PLM for information. LAN-1500-AEN.pdf (http://csmedia.corning.com/opcomm/ Resource_Documents/additional_information_rl/LAN-1500-AEN. pdf) LAN-1242 Corning Optical Communications LLC PO Box 489 Hickory, NC 28603-0489 USA 800-743-2675 FAX: 828-325-5060 International: +1-828-901-5000 www.corning.com/opcomm A complete listing of the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are the properties of their respective owners. Corning Optical Communications is ISO 9001 certified. 2014 Corning Optical Communications. All rights reserved. Page 21 Revision date 2014-12-14
Part Number Description 020201R3116002M 1 F Single Mode OS2 Single Mode, LC UPC Simplex - LC UPC Simplex, 2 Meters, 1.6mm, Indoor,Riser Interconnect, Circular Yellow Fiber Optic Cable Assembly Corning Cable Systems LLC PO Box 489 Hickory, NC 28603-0489 USA 800-743-2675 FAX: 828-325-5060 International: +1-828-901-5000 www.corning.com/cablesystems. A complete listing of the trademarks of Corning Cable Systems is available at www.corning.com/cablesystems/trademarks. Corning Cable Systems is ISO 9001 certified. 2014 Corning Cable Systems. All rights reserved.