INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls Security system harness Control unit Control unit bracket LED (Not used.) Push nut (Not used.) Relay, 4-pin 2-Pin connector (for LED) (Not used.) Disarm switch Relay, 6-pin Window decal 3-Pin connector (for disarm switch) Nut Washer Owner s Manual Fuse label 4 Grommets 4 Self-tapping screws 2 Washer-screws 9 Wire ties 2003 American Honda Motor Co., Inc. - All Rights Reserved. AII 26327 (0310) 08E55-S2A-1010-91 1 of 8
Wire tie with clip Antenna bracket Adjusting the Control Unit Use a small flat-tip screwdriver to change the mode switch and the horn/siren switch and to adjust sensitivity. The horn/siren switch must be set in the "HORN" position. Washer-bolt GLASS BREAKAGE SENSOR MODE SWITCH Flange nut TOOLS AND SUPPLIES REQUIRED Small flat-tip screwdriver Phillips screwdriver Center punch Eye protection (face shield, safety goggles, etc.) Drill 5.5 mm and 12 mm Drill bits Tape measure File Felt-tip pen Ratchet 10 mm, 12 mm, and 14 mm Sockets Piece of cardboard Diagonal cutters Electrical tape Torque wrench Illustration of Security System Installed on the Vehicle DISARM SWITCH FUSE CASE (2A) 4-PIN RELAY CONTROL UNIT 6-PIN RELAY 3429090M MIN MAX Mode Switch: Set the mode switch according to the customer s choice. Refer to the Owner s Manual for the explanation of each mode. Glass Breakage Sensor: AUTO LOCK AUTO MANUAL SENSITIVITY ADJUSTMENT KNOB Do not attach anything like scotch tape over the holes; this is a microphone pickup. Sensitivity Adjustment Knob: SIREN HORN Adjust the sensitivity only if the customer requests it; the sensitivity adjustment of the glass breakage sensor is factory-set. Be careful when you adjust the sensitivity; if you raise the sensitivity too much, the security system can give a false alarm, and if the sensitivity is too low, the security system may not work even if glass is broken. 2 of 8 AII 26327 (0310) 2003 American Honda Motor Co., Inc. - All Rights Reserved.
INSTALLATION Customer Information: The information in this Installation Instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Remove the front left door sill trim (three retaining clips). 5. Remove the lower steering column cover (three screws, and pull gently to release the four tabs). DOOR SILL TRIM RETAINING LOWER STEERING COLUMN COVER SCREW PUSH TAB 6. Remove the driver s seat (four bolts, and unplug the connector). Place the seat on a piece of cardboard. SEAT BOLT Torque: 22 N m (16 lb-ft) 4. Remove the left kick panel (three clips). KICK PANEL DRIVER S SEAT SEAT BOLT Torque: 29 N m (22 lb-ft) 3429100M 2003 American Honda Motor Co., Inc. - All Rights Reserved. AII 26327 (0310) 3 of 8
7. Push the four grommets into the square holes in the bottom of the driver s seat cushion. DRIVER S SEAT 11. Install the control unit bracket and the 4-pin relay onto the bottom of the driver s seat cushion (three self-tapping screws). CONTROL UNIT BRACKET DRIVER S SEAT GROMMET 8. Install the control unit on the control unit bracket (two 4 x 30 mm screws). 6-PIN RELAY 9. Install the antenna bracket on the control unit bracket (one 6 x 12 mm washer-bolt and one 6 mm flange nut). SELF- TAPPING SCREW 4-PIN RELAY SELF-TAPPING SCREW 4 x 30 mm SCREWS 12. Install the 6-pin relay onto the bottom of the driver s seat cushion (one self-tapping screw). CONTROL UNIT ANTENNA ANTENNA BRACKET 60 mm CONTROL UNIT BRACKET 6 x 12 mm WASHER-BOLT ANTENNA BRACKET WIRE TIE WITH 6 mm FLANGE NUT 3429030M 10. Attach the wire tie with clip to the antenna, then push the clip into the hole in the antenna bracket. 4 of 8 AII 26327 (0310) 2003 American Honda Motor Co., Inc. - All Rights Reserved.
13. Under the dash on the driver's side of the vehicle, measure and mark the bottom of the dashboard. 16. Get the 3-pin connector included in the kit. Firmly push the disarm switch terminals into the 3-pin connector until they click into position, then lower the lock. 30 mm 60 mm 12 mm DRILL BIT 10 mm ELECTRICAL TAPE BLACK WIRE BLUE WIRE 3-PIN 14. While wearing eye protection, lightly center-punch the mark, and drill a 12 mm hole: Wrap electrical tape around the end of the 5.5 mm and 12 mm drill bits about 10 mm from the tip. First drill a pilot hole with a 5.5 mm bit, then finish with a 12 mm bit. Remove all burrs. 15. Route the terminal ends from the disarm switch through the hole you just drilled, and secure it with the washer and the 12 mm nut from the kit. BLACK WIRE BLUE WIRE 3-PIN LOCK WASHER 12 mm NUT DISARM SWITCH TERMINAL END 2003 American Honda Motor Co., Inc. - All Rights Reserved. AII 26327 (0310) 5 of 8
17. On the driver's side, lift up the floor carpet, and route the 22-pin, 4-pin, and 6-pin connectors from the security system harness out through the cutout in the floor carpet. 4-PIN 22-PIN 19. Route the two 17-pin connectors from the security system harness forward and under the carpet. VEHICLE 17-PIN (Unplug.) BLUE TAPE (Remove.) VEHICLE 2-PIN 6-PIN GREEN TAPE WIRE TIE VEHICLE CORRUGATED TUBE 17-PIN 2-PIN 3429051M 3429040M 20. Next to the hood opener lever, locate the two vehicle harness 17-pin connectors. Unplug the vehicle harness 17-pin connector, and plug the security system harness 17-pin connectors in between. 21. Remove the blue tape from the vehicle 2-pin connector, and plug in the vehicle 2-pin connector into the security system harness 2-pin connector. 18. Secure the security system harness to the corrugated tube of the vehicle harness with one wire tie at the green tape. 6 of 8 AII 26327 (0310) 2003 American Honda Motor Co., Inc. - All Rights Reserved.
22. Attach the two (3A) fuse labels to the security system harness fuse case. 26. Secure the security system harness to the vehicle harness with five wire ties in the areas shown. KEYLESS ENTRY CONTROL UNIT FUSE CASE FUSE LABEL (3A) 18-PIN WIRE TIE WIRE TIE 3429070M VEHICLE 18-PIN 3429060M 27. Along the door opening, secure the security system harness to the vehicle harness with three wire ties. 23. Unplug the vehicle 18-pin connector from the keyless entry control unit, and plug the security system harness 18-pin connectors in between. 24. Unplug the light switch 16-pin connector, and plug the security system harness 16-pin connectors in between. DISARM SWITCH 3-PIN VEHICLE 16-PIN 16-PIN WIRE TIE 3429080M 3-PIN 25. Plug the disarm switch 3-pin connector into the security system harness. 2003 American Honda Motor Co., Inc. - All Rights Reserved. AII 26327 (0310) 7 of 8
29. Tilt the driver s seat-back forward, then reach under the front of the seat, and plug the security system harness 22-pin connector into the control unit. Plug the 4-pin and 6-pin connectors into the 4-pin and 6-pin relays. SEAT CUSHION SEATBACK SEAT 32. Check that all wire harnesses are routed properly and all connectors are plugged in. 33. Reinstall all removed parts. 34. Reconnect the negative cable to the battery. 35. Reset the radio station presets and clock. 36. Check operation of the security system according to the Security System Owner s Manual supplied. The LED indicator is located in the instrument cluster. CONTROL UNIT 22-PIN 4-PIN RELAY 6-PIN RELAY WIRE TIE WITH 4-PIN 6-PIN 30. Push the wire tie with clip of the security system harness into the hole in the control unit bracket. 31. Plug in the seat harness connectors, then reinstall the driver s seat. Torque the rear seat bolts of the front seat to 29 N m (22 lb-ft), and torque the front seat bolts of the front seat to 22 N m (16 lb-ft). 8 of 8 AII 26327 (0310) 2003 American Honda Motor Co., Inc. - All Rights Reserved.