Input Shafts Option G1, ISO 3019-1, outer dia 32 mm-4 (SAE C, 14 teeth) 31.5 ±1 [1.240 ±0.039] MOUNTING FLANGE SURFACE FLANGE 127-4 PER ISO 3019-1 SPLINE DATA NUMBER OF TEETH : 14 PITCH FRACTION : 12/24 PRESSURE ANGLE : 30 PITCH-Ø : 29.633 TYP OF FIT : FLAT ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 5 Ø26 ±0.25 [1.024 ±0.010] Ø31.14 ±0.09 [1.226 ±0.004] 8.05 ±0.8 [0.317 ±0.031] 48 ±1 [1.890 ±0.039] COUPLING MUST NOT PROTRUDE BEYOND THIS SURFACE Option G9, ISO 3019-1, outer dia 38 mm-4 (SAE C-C, 23 teeth) P003 265E Specifications Option Spline Min active spline length 2 Torque rating 1 Rated torque Maximum torque mm [in] Nm Nm G1 14 teeth, 12/24 pitch 31.45 [1.238] 534 [4720] 816 [7220] For definitions of maximum and rated torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. Minimum active spline length for the specified torque ratings. T000 146E MOUNTING FLANGE SURFACE FLANGE 127-4 PER ISO 3019-1 40.5 ±1 [1.594 ±0.039] SPLINE DATA NUMBER OF TEETH : 23 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH-Ø : Ø36.513 [Ø1.438] TYP OF FIT : FLAT ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 5 Specifications 8.05 ±0.8 [0.317 ±0.031] Ø33.6 ±0.25 [1.323 ±0.010] COUPLING MUST NOT PROTRUDE BEYOND THIS SURFACE Ø37.59 ±0.09 [1.480 ±0.004] 54 ±1 [2.126 ±0.039] P003 264E Option Spline Min active spline length 2 Torque rating 1 Rated torque Maximum torque mm [in] Nm Nm G9 23 teeth, 16/32 pitch 40.33 [1.588] 999 [8840] 1818 [16 090] For definitions of maximum and rated torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. Minimum active spline length for the specified torque ratings. T000 147E 20 11062169
Input Shafts Option F1, ISO 3019-1, outer dia 35 mm-4 (SAE C, 21 teeth) 34.5 ±1 [1.358 ±0.039] MOUNTING FLANGE SURFACE FLANGE 127-4 PER ISO 3019-1 SPLINE DATA NUMBER OF TEETH : 21 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH-Ø : Ø33,337 [Ø1,313] TYP OF FIT : FLAT ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 5 8.05 ±0.8 [0.317 ±0.031] Ø30.4 ±0.25 [1.197 ±.010] 48 ±1 [1.890 ±0.039] COUPLING MUST NOT PROTRUDE BEYOND THIS SURFACE Ø34.42 ±0.09 [1,355 ±,004] P003 263E Specifications Option Spline Min active spline length 2 Torque rating 1 Rated torque Maximum torque mm [in] Nm Nm F1 21 teeth, 16/32 pitch 34.5 [1.358] 760 [6730] 1137 [10 060] For definitions of maximum and rated torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. Minimum active spline length for the specified torque ratings. T000 148E 11062169 21
Input Shafts Option F4, ISO 3019-1, Code 38-3, Diameter 38.1 taper 1:8, without key and no through-hole in the end of the shaft (38,1) [1.500] MOUNTING FLANGE SURFACE FLANGE 127-4 PER ISO 3019-1 CONICAL KEYED SHAFT END SIMILAR TO ISO 3019-1 CODE 38-3 SUITABLE KEY 3/8x3/8x1 1/2 ANSI B17.1 125±0,5:1000 SHAFTS 1 1/8-12UNF 7.88 ±0.8 [0.310 ±0.031] (47) [1.850] 81.9 ±1 34.9 ±1 [1.374 ±0.039] [3.224 ±0.039] COUPLING MUST NOT OVERLAP TILL THIS POINT P003 518E Specifications Torque rating 1) Option Tapered shaft Rated torque* Maximum torque Nm Nm F4 38.1 taper without key 1116 [9880] 1488 [13 170] For definitions of maximum and rated torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. Mating part must maintain a minimum gap width of 1.0 mm with the shaft shoulder after installation of the part. Transmittable torque will be reduced if the minimum gap requirement is not met. Tapered shaft customer acknowledgement The Sauer-Danfoss H1 tapered shaft has been designed using the industry standard ISO 3019-1, minus the through-hole in the end of the shaft. Sauer-Danfoss recommends a self-locking nut instead of a castle nut and pin. The nut and mating square-cut key are customer supplied. The specified torque rating of the tapered shaft documented above is based on the cross-sectional diameter of the shaft, through the keyway, and assumes the proper clamp and fit between shaft and coupling. Sauer-Danfoss guarantees the design and manufactured quality of the tapered shaft. The customer is responsible for the design and manufactured quality of the mating female coupling and key and applied torque on the nut. Sauer-Danfoss has made provisions for the key in accordance to the ISO specification with the understanding that the key is solely to assist in the installation of the mating coupling. T000 149E C Torque must be transmitted by the taper fit between the shaft and it s mating coupling, not the key. Torque or loading inadvertently transmitted by the customer supplied key may lead to premature shaft failure. 22 11062169
Auxiliary Mounting Pads Option H2, ISO 3019-1, flange 82-2 (SAE A, 9 teeth) 2x 106.4 ±0.35 [4.189 ±0.014] 4x 53.2 ±0.18 [2.09 ±0.007] MOUNTING FLANGE SURFACE FLANGE 82-2 PER ISO 3019-1 294.956 ±2 [11.612 ±0.079] 279.83 ±2 [11.017 ±0.079] 14.801 +1-0 [0.583] +0.039-0 88.621 +0.13 [3.489] +0.005-0 -0 82.601 +0.076-0 [3.252] +0.003-0 R0.8 MAX [0.031] THREAD: M10x1.5-6H THD DEPTH: 15 [0.591] MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF 82.22 [3.237] I.D. 2.62 [0.103] CROSS SECTION 1.956 [0.077] 8.101 ±0.25 [0.319 ±0.010] 61.68 [2.428] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 9 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : 14.288 [ 0.5625] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 6 P003 262E Specifications Option Spline Torque rating 1 maximum torque Nm H2 9 teeth, 16/32 pitch 162 [1430] For definitions of maximum torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. T000 150E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed. 11062169 23
Auxiliary Mounting Pads Option H1, ISO 3019-1, flange 82-2 (SAE A, 11 teeth) 2x 106.4 ±0.35 [4.189 ±0.014] 4x 53.2 ±0.18 [2.09 ±0.007] MOUNTING FLANGE SURFACE FLANGE 82-2 PER ISO 3019-1 19.801 +1 [0.780] +.039 0 0 294.956 ±2 [11.612 ±0.079] 279.83 ±2 [11.017 ±0.079] 88.621 +0.13 0 [3.489] +0.005 0 82.601 +0.076 0 [3.252] +0.003 0 R0.8 MAX [0.031] THREAD: M10x1.5-6H THD DEPTH: 15 [0.591] MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF 82.22 [3.237] I.D. 2.62 [0.103] CROSS SECTION 1.956 [0.077] 8.1 ±0.25 [0.319 ±0.010] 61.68 MAX. AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 11 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : 17.463 [ 0. 6875] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 6 MIN ACTIVE SPLINE LENGTH 105MM P003 321E Specifications Option Spline Torque rating 1 maximum torque Nm H1 11 teeth, 16/32 pitch 296 [2620] For definitions of maximum torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. T000 151E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed. 24 11062169
Auxiliary Mounting Pads Option H3, ISO 3019-1, flange 101-2 (SAE B, 13 teeth) 2x 146 ±0.35 [5.748 ±0.014] 4x 73 ±0.18 [2.87 ±0.007] MOUNTING FLANGE SURFACE FLANGE 101-2 PER ISO 3019-1 19.801 +1 [0.780] +0.039-0 -0 295.459 ±2 [11.32 ±0.079] 279.83 ±2 [11.017 ±0.079] 107.823 +0.13-0 [4.245] +0.005-0 R0.8 MAX [0.031] 101.651 +0.076-0 [4.002] +0.003-0 THREAD: M12x1.75-6H THD DEPTH : 20 [0.787]MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF 101.32 [ 3.989] ID X 2.62 [0.103] CROSS SECTION 1.956 [0.077] 11.4 ±0.25 [0.449 ± 0.010] 61.68 [2.428] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 13 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : 20.638 [ 0.813] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 6 P003 322E Specifications Option Spline Torque rating 1 maximum torque Nm H3 13 teeth, 16/32 pitch 395 [3500] For definitions of maximum torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. T000 152E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed. 11062169 25
Auxiliary Mounting Pads Option H5, ISO 3019-1, flange 101-2 (SAE B-B, 15 teeth) 2x 146 ±0.35 [5.748 ±0.014] 4x 73 ±0.175 [2.874 ±0.007] MOUNTING FLANGE SURFACE FLANGE 101-2 PER ISO 3019-1 19.8 +1-0 [0.780] +0.039-0 295.486 ±2 [11.633 ±0.079] 279.83 ±2 [11.017 ±0.079] 107.823 +0.13-0 [4.245] +0.005-0 101.651 +0.076-0 [4.002] +0.003-0 R0.8 MAX [0.031] THREAD: M12x1.75-6H THD DEPTH : 20 [0.787]MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF 101.32 [3.989] ID X 2.62 [.103] CROSS SECTION 1.956 [0.077] 11.4 ±0.25 [0.449 ±0.010] 61.68 [2.428] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 15 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : 23.813 [ 0.938] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 6 P003 261E Specifications Option Spline Torque rating 1 maximum torque Nm H5 15 teeth, 16/32 pitch 693 [6130] For definitions of maximum torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. T000 153E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed. 26 11062169
Auxiliary Mounting Pads 2x 114.5 ±0.35 [4.508 ±0.014] 4x 57.25 ±0.18 [2.25 ±0.007] Option H6, ISO 3019-1, flange 127-4 (SAE C, 14 teeth) MOUNTING FLANGE SURFACE FLANGE 127-4 PER ISO 3019-1 21.98 +1-0 [0.865] +0.039-0 297.907 ±2 [11.729 ±0.079] 282.015 ±2 [11.103 ±0.079] 2x 90.5 ±0.175 [3.563 ±0.007] 181 ±0.35 [7.126 ±0.014] 134.06 +0.13-0 [5.278] +0.005-0 127.05 +0.076-0 [5.002] +0.003-0 THREAD : M12x1.75-6H THD DEPTH: 21 [0.823] MIN RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x THREAD : M16 x2-6h THD DEPTH: 25 [0.984] MIN RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 2x O-RING SEAL REQUIRED REF 120.32 [4.737] I.D. 2.62 [0.103] CROSS SECTION 1.956 [0.077] 13.5 ±0.25 [0.531± 0.010] 63.86 [2.514] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 14 PITCH FRACTION : 12/24 PRESSURE ANGLE : 30 PITCH- : 29.633 [ 1.167] TYP OF FIT : FILLETT ROOT, SIDE FIT PER : ANSI B92.1-1996 CLASS 6 MIN ACTIVE SPLINE LENGTH 17.8MM P003 260E Specifications Option Spline Torque rating 1 maximum torque Nm H6 14 teeth, 12/24 pitch 816 [7220] For definitions of maximum torque values, refer to: Basic Information Manual 11062168, section Shaft Torque Ratings and Spline Lubrication. T000 154E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed. 11062169 27
Port Description SERVO GAGE PORT "M4" PORT ISO 11926-1 -7/16-20 21 MAX CLEARANCE DIA FOR FITTING SYSTEM PORT "B" 25.4-450BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X 1.75 20 MIN. FULL THREAD DEPTH RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA CONNECTOR : DEUTSCH DT04-2P CASE PRESSURE PORT 42 MAX CLEARANCE DIA FOR FITTING CCW Rotation CW Rotation M12 X 1,75 SYSTEM PORT "A" 25.4-450BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X 1.75 20 MIN. CASE DRAIN PORT "L4" FULL THREAD DEPTH PORT ISO 11926-1 -1 1/16-12 RECOMMENDED SCREW-IN DEPTH 48 MAX CLEARANCE DIA FOR FITTING 1.5 x THREAD DIA CHARGE INLET PORT "S" PORT ISO 11926-1 -1 5/16-12 63 MAX CLEARANCE DIA FOR FITTING SYSTEM A GAGE PORT "MA" PORT ISO 11926-1 -9/16-18 28 MAX CLEARANCE DIA FOR FITTING P003 324E Port description Port Description Sizes A System port A 25.4 B System port B 25.4 E 7 /8-14 F 7 /8-14 L2 1 1 /16-12 L4 1 1 /16-12 MA System A gage port 9 /16-18 MB 9 /16-18 M3 9 /16-18 M4 Servo gage port 7 /16-20 M5 Servo gage port 7 /16-20 M14 7 /16-20 S 1 5 /16-12 T000 204E 30 11062169
Port Description SYSTEM B GAGE PORT "MB" PORT ISO 11926-1 -9/16-18 28 MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO 11926-1 -5/16-24 CHARGE FILTRATION PORT "F" 42 MAX CLEARANCE DIA FOR FITTING TO FILTER CASE GAGE PORT "M14" PORT ISO 11926-1 -7/16-20 21 MAX CLEARANCE DIA FOR FITTING (EDC, FNR, NFPE) CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER CASE PRESSURE PORT Ø42 MAX CLEARANCE DIA FOR FITTING CONNECTOR : DEUTSCH DT04-2P SERVO GAGE PORT "M5" PORT ISO 11926-1 -7/16-20 21 MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO 11926-1 -5/16-24 CASE DRAIN PORT "L2" PORT ISO 11926-1 -1 1/16-12 48 MAX CLEARANCE DIA FOR FITTING CHARGE GAGE PORT "M3" PORT ISO 11926-1 -9/16-18 28 MAX CLEARANCE DIA FOR FITTING AFTER FILTERING P003 325E 11062169 31
152.9 ±1.0 [6.02 ±0.04] Z Servo gage port M4 Port ISO 11926-1 - 7 /16-20 21 max. clearance dia for fitting System port B 25.4 450 bar Split flange boss per ISO 6162 M12x1.75 20 min. full thread depth recommended screw-in depth 1.5 x thread dia 126.1 ±1.0 [4.96 ±0.04] 104.0 ±1.0 [4.09 ±0.04] 69.5 ±1.0 [2.74 ±0.04] 65.0 + 0.2 0.1 [2.559 + 0.004 0.008 ] 65.0 + 0.2 0.1 [2.559 + 0.004 0.008 ] (4x)27.8 ±0.25 [1.09 ±0.01] 52.0 ±0.2 [2.05 ±0.01] (8x)13.9 ±0.25 [0.55 ±0.01] Charge inlet port S Port ISO 11926-1 - 1 5 /16-12 63.0 max. clearance dia for fitting (8x) 28.6 ±0.25 [1.13 ±0.01] System port A 25.4 450 bar Split flange boss per ISO 6162 M12x1.75 20 min. full thread depth recommended screw-in depth 1.5 x thread dia B-B (2x) Connector : Deutsch DT04-2P to be paint free C (4x) 57.2 ±0.25 [2.25 ±0.01] 278.3 ±2 [10.958 ±0.079] 216.0 + 0.5 0.6 [8.505 + 0.024 0.020 ] C 214.0 + 0.6 0.5 [8.426 + 0.024 0.020 ] C-C D D 92.4 ±0.2 [3.64 ±0.01] 154.2 ±1.0 [6.07 ±0.04] 139.3 ±1.0 [5.48 ±0.04] 135.7 ±1.0 [5.34 ±0.04] B B 15 ±0.2 [0.59 ±0.01] Case drain port L4 Port ISO 11926-1 - 1 1 /16-12 48.0 max. clearance dia for fitting 45.2 ±1.0 [1.78 ±0.04] Case pressure port Port ISO 11926-1 - 7 /8-14 42.0 max. clearance dia for fitting 12.45 ±0.25 [0.49 ±0.01] 1.5 ±0.5 x 45 ±5 [0.059 ±0.020 x 45 ] R 0.8 max. [0.031] 89.0 ±0.2 [3.50 ±0.01] Shafts to be paint free 48.0 ±1 [1.89 ±0.04] D-D Mounting flange surface Flange 127-4 per ISO 3019-1 to be paint free 8.05 ±0.8 [0.32 ±0.03] 31.5 ±1 [1.24 ±0.04] 127.0 0 0.05 [5.0 0 0.002 ] Coupling must not protrude beyond this surface Shaft LC Shaft LC Shaft LC P003 326E 32 11062169
Y mm [in] 45.2 ±1.0 [1.78 ±0.04] Case pressure port Port ISO 11926-1 - 7 /8-14 42.0 max. clearance dia for fitting 154.2 ±1.0 [6.07 ±0.04] 139.3 ±1.0 [5.48 ±0.04] Connector : Deutsch DT04-2P to be paint free Servo gage port M5 Port ISO 11926-1 - 7 /16-20 21 max. clearance dia for fitting Charge pressure construction port Port ISO 11926-1 - 5 /16-24 138.18 ±2 [5.44 ±0.079] 1.37 [0.054] Z 108.9 ±2 [4.29 ±0.079] 152.9 ±1.0 [6.02 ±0.04] 126.1 ±1.0 [4.96 ±0.04] 104.0 ±1.0 [4.09 ±0.04] G 178.9 ±2.0 [7.04 ±0.079] X 23.7 [0.93] G 95.0 ±2.0 [3.74 ±0.079] Case drain port L2 Port ISO 11926-1 - 1 1 /16-12 48.0 max. clearance dia for fitting 99.7 ±1.0 [3.93 ±0.04] 142.7 [5.62] Approximate center of gravity Charge gage port M3 Port ISO 11926-1 - 9 /16-18 28 max. clearance dia for fitting after filtering Approximate center of gravity G-G W 88.0 ±0.2 [3.46 ±0.01] F-F Shaft LC 12 206.2 ±2 [8.118 ±0.079] 128.4 ±2 [5.055 ±0.079] CASE GAGE PORT "M14" PORT ISO 11926-1 -7/16-20 21 MAX CLEARANCE DIA FOR FITTING 77.2 ±1 [3.039 ±0.039] Y 231.415 ±1 [9.111 ±0.039] 232.515 ±1 [9.154 ±0.039] 235.515 ±1 [9.272 ±0.039] F E SYSTEM B GAGE PORT "MB" PORT ISO 11926-1 -9/16-18 28 MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO 11926-1 -5/16-24 7 ±1 [0.276±0.039] F 67 ±1 [2.638 ±0.039] 53.5 ±1 [2.106 ±0.039] E CHARGE FILTRATION PORT "F" 42 MAX CLEARANCE DIA FOR FITTING TO FILTER CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 12 E-E Charge filtration port F 20.47 Port ISO 11926-1 - 7 /8-14 42.0 max. clearance dia for fitting to filter 96.5 ±1.0 [3.80 ±0.04] 96.6 ±1.0 [3.78 ±0.04] Charge filtration port E Port ISO 11926-1 - 7 /8-14 42.0 max. clearance dia for fitting from filter P003 327E 11062169 33
View W View X mm [in] SYSTEM A GAGE PORT "MA" PORT ISO 11926-1 -9/16-18 28 MAX CLEARANCE DIA FOR FITTING 216.015 ±1 [8.505 ±0.039] 67 ±1 [2.638 ±0.039] CCW Rotation CW Rotation 4x 57.25 ±0.25 [2.254 ±0.010] 4x 30 ±0.25 [1.181 ±0.010] OTHER SIDE SCREW HEAD SPACE 4x 57.249 ±0.25 [2.254 ±0.010] 4x w 14.34 ±0.19 [0.565 ±0.007] P003 328E 34 11062169
Controls Electric Displacement Control (EDC), option A2 (12 V)/A3 (24 V) mm [in] CONNECTOR : DEUTSCH DT04-2P 209 MAX [8.228] 128.4 ±2 [5.055 ±0.079] 64.2 ±1 [2.528 ±0.039] CASE GAGE PORT "M14" PORT ISO 11926-1 -7/16-20 Ø21 MAX CLEARANCE DIA FOR FITTING SHAFT 77.2 ±1 [3.039 ±0.039] MOUNTING FLANGE 178.86 ± 1 [7.042 ± 0.039] 2x 152.86 ± 1 [6.018 ± 0.039] SHAFT CONNECTOR : DEUTSCH DT04-2P 2x 139.3 ± 1 [5.484 ± 0.039] P003 330E Electric Displacement Control (EDC), with manual override, option A4 (12 V)/A5 (24 V) CONNECTOR : DEUTSCH DT04-2P 209 MAX [8.228] 128.4 ± 2 [5.055 ± 0.079] 64.2 ± 1 [2.528 ± 0.039] CASE GAGE PORT "M14" PORT ISO 11926-1 -7/16-20 21 MAX CLEARANCE DIA FOR FITTING SHAFT 77.2 ± 1 [3.04 ± 0.039] MOUNTING FLANGE 178.86 ± 1 [7,042 ± 0.039] 2x 152.86 ± 1 [6.018 ± 0.039] CONNECTOR : DEUTSCH DT04-2P P003 259E SHAFT 2x139.3 ± 1 [5.484 ± 0.039] 11062169 35
Controls Forward-Neutral-Reverse (FNR) with manual override, option A9 (12 V)/B1 (24 V) CONNECTOR : DEUTSCH DT04-2P mm [in] 209 MAX [8.228] 128.4 ± 2 [5.055 ± 0.079] 64.2 ± 1 [2.528 ± 0.039] CASE GAGE PORT "M14" PORT ISO 11926-1 -7/16-20 21 MAX CLEARANCE DIA FOR FITTING SHAFT MOUNTING FLANGE CONNECTOR DEUTSCH DT04-2P: 77.2 ± 1 [3.04 ± 0.039] 178.86 ± 1 [7.042 ± 0.039] 2x 152.86 ± 1 [6.018 ± 0.039] SHAFT 2x 139.3 ± 1 [5.484 ± 0.039] P003 257E Non Feedback Proportional Electric control (NFPE), with manual override, option A8 (12 V)/B8 (24 V) CONNECTOR: DEUTSCH DT04-2P 209 MAX [8.228] 128.4 ± 2 [5.055 ± 0.079] 64.2 ± 1 [2.528 ± 0.039] CASE GAGE PORT "M14" PORT ISO 11926-1 -7/16-20 21 MAX CLEARANCE DIA FOR FITTING SHAFT PLUG REMOVING CAN CAUSE CONTAMINATION ISSUES 77.2 ± 1 [3.04 ± 0.039] MOUNTING FLANGE 179.28 ± 1 [7.058 ± 0.039] 2x 152.86 ± 1 [6.018 ± 0.039] SHAFT CONNECTOR: DEUTSCH DT04-2P 2x 139.3 ± 1 [5.484 ± 0.039] P003 363E 36 11062169
2x WRENCH SIZE 4 Displacement limiters Displacement limiters, option B 130.95 ±1 [5.156 ±0.039] 150 MAX [5.906] 150 MAX [5.906] mm [in] 84.5 ±1 [3.327 ±0.039] 2x WRENCH SIZE 13 P003 255E 11062169 37
Filtration Suction filtration, option L mm [in] 216.015 +0.6-0.5 [8.505] +0.024-0.020 8x 28.6 ±0.25 [1.126 ±0.010] 4x 57.2 ±0.25 [2,252 ±0.010] CHARGE PRESSURE CONSTRUCTION PORT PORT ISO 11926-1 -5/16-24 SYSTEM B GAGE PORT "MB" PORT ISO 11926-1 -9/16-18 Ø28 MAX CLEARANCE DIA FOR FITTING SYSTEM PORT "B" Ø25.4-450BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X 1.75 20 MIN. FULL THREAD DEPTH RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 65 +0.1-0.2 CHARGE INLET PORT "S" [2.559] +0.004-0.008 PORT ISO 11926-1 -1 5/16-12 Ø63 MAX CLEARANCE DIA FOR FITTING 8x 13.9 ±0.25 [0.547 ±0.010] 4x 27.8 ±0.25 [1.094 ±0.010] 65 +0.1-0.2 [2.559] +0.004-0.008 SYSTEM PORT "A" Ø25.4-450BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X 1.75 20 MIN. FULL THREAD DEPTH RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA P003 329E 38 11062169
Filtration Remote full charge pressure filtration, option P for end cap option F5 (SAE-C PTO) 12 F-F mm [in] SYSTEM B GAGE PORT "MB" PORT ISO 11926-1 -9/16-18 Ø28 MAX CLEARANCE DIA FOR FITTING 8.5 ±1 [0.335±0.039] 67 ±1 [2. 638 ±0.039] CHARGE FILTRATION PORT "F" Ø42 MAX CLEARANCE DIA FOR FITTING TO FILTER 106.6 ±1 [4.197 ±0.039] F F 55.5 ±1 [2.185 ±0.039] 12 E-E E E CHARGE FILTRATION PORT "F" Ø42 MAX CLEARANCE DIA FOR FITTING TO FILTER CHARGE FILTRATION PORT "E" Ø42 MAX CLEARANCE DIA FOR FITTING FROM FILTER CHARGE PRESSURE CONSTRUCTION PORT PORT ISO 11926-1 -5/16-24 CHARGE FILTRATION PORT "E" Ø42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 96.5 ±1 [3.799 ±0.039] P301 298 11062169 39
Filtration Integral full flow charge pressure filtration with filter bypass sensor, option M mm [in] 186.268 ±1 [7.333 ±0.039] 208.649 ±1 [8.215 ±0.039] 123.26 ±1 [4.853 ±0.039] CONNECTOR: DEUTSCH DTM04-2P CHARGE GAGE PORT "M6" PORT ISO 11926-1 -9/16-18 Ø28 MAX CLEARANCE DIA FOR FITTING BEFORE FILTER 40.6 ±1 [1.598 ± 0.039] 77.751 ±1 [3.061 ±0.039] 276.405 ±1 [10.882 ±0.039] 285.214 ±1 [11.229 ±0.039] 53.58 ±1 [2.110 ±0.039] P003 246E 40 11062169
Filtration Integral full flow charge pressure filtration with filter bypass sensor, option M, for end cap option F4 (SAE-C PTO) mm [in] 198.267 ±1 [7.806 ±0.039] 220.7 ±1 [8.687 ±0.039] 135.268 ±1 [5.326 ±0.039] CONNECTOR: DEUTSCH DTM04-2P 53.58 ±1 [2.110 ±0.039] CHARGE GAGE PORT "M6" PORT ISO 11926-1 -9/16-18 Ø28 MAX CLEARANCE DIA FOR FITTING BEFORE FILTER 77.751 ±1 [3 061 ±0 039] 40.6 ±1 [1.598 ±0.039] 276.405 ±1 [10.882 ±0.039] 285.214 ±1 [11.229 ±0.039] P301 297 11062169 41
Filtration External full flow charge pressure filtration, option S for end cap options D8 or F5 231.415 ±1 [9.111 ±0.039] CHARGE INLET PORT "S" PORT ISO 11926-1 -1 5/16-12 CLOSED WITH PLUG 232.515 ±1 [9.154 ±0.039] E SYSTEM B GAGE PORT "MB" PORT ISO 11926-1 -9/16-18 28 MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO 11926-1 -5/16-24 E 67 ±1 [2.638 ± 0.039] 53.5 ±1 [2.106 ± 0.039] CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 12º E-E CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 96.5 ±1 [3.799 ± 0.039] P301 299 mm [in] 42 11062169