ATA TO IDE INTERFACE PC CARD DRIVES 1 Front slot Support Type I/II/III ATA Flash, ATA HDD, Compact Flash Cards(an adaptor required) Operating Temperature: 0 o C- 70 o C 1 real slot Support Type I/II/III ATA Flash, ATA HDD, Compact Flash Cards(an adaptor required) 1/2 size interface card form factor Operating Temperature: 0 o C- 70 o C
2 Front slots 2 rear slots. 2 Front Slot. Specific 40 pins IDE and 4 pins power connectors.. With Hot Swap Software under operation system. DOS, Win98/Me/2000/XP..
ATA to Standard IDE interface. 2 Rear Slot 40 pins IDE & 4 pins power connectors Support Type I/II/III ATA Flash Cards, ATA HDD, Compact Flash Card With special design hardware circuit support Hot Swap function With "Hot Swap" software 5V 70mA power consumption. 2 in 1, combines one FDD with one IDE Drive Standard 34 pins FDD and 4 pins power connector 40 pins IDE and 4 pins power connector Standard 3.5" Driver form factor.. Supports Compact Flash Type I II (Micro Drive) Through 50-pin Compact Flash connector directly (Adapter not required).. 5V, 70mA power consumption. (typical) Can be mounted on 3.5" Drive bay. Dimensions: 109.6 x 101.6 x 25.4mm. With special design hardware circuit support " Hot Swap " function.
2 Front Slot Supports Type I/II ATA Flash, ATA HDD and Type I/II Compact Flash Cards through 68-pin PCMCIA connector & 50-pin Compact Flash connector 5V, 70mA power consumption. (typical) Can be mounted on 3.5" Drive bay. Dimensions: 109.6 x 101.6 x 25.4 m with "Hot Swap" software Support DMA mode (Serial ATA ) Without Special cable use normal IDE cable. With special design hardware circuit support Hot Swap Function With "Hot Swap" software ATA to Standard IDE interface. 1 Rear Slot 40 pins IDE & 4 pins power connectors Support Type I/II/III ATA Flash Cards, ATA HDD, Compact Flash Card With special design hardware circuit support Hot Swap function With "Hot Swap" software 5V 70mA power consumption 2.5" form factor Supports Compact Flash Type I /II (Micro Drive) Optional 40 pins IDE and 4 pins power connectors or 44 pins Connector Access LED indicator One Compact Flash socket w/ejector Dimensions: 75mm x 70mm Screw bracket of Rear slot Master/Slave optional.
40pin 2.54mm 180 FXangled connector (vertical type )connect to IDE port directly w/o IDE cable Supports 50-pin Compact Flash Type I /II &ATA HDD (Micro Drive) Dimensions: 55mm x 48mm 5V, 5mA power consumption. (typical) Support DMA mode Master/Slave optional The PCM-212 ATA and PCM-212 C.F. are PC Card Drives which allow PC compatible computer with an IDE controller to use a PCMCIA ATA Flash, ATA Hard Disk Drive and Compact Flash. This Card Drive Module automatically sets 50 pins ATA mode of PCMCIA Card or Compact Flash Card allowing the system bios to access the card directly as a IDE Drive. The PCM-212 ATA and PCM-212 C.F. comply PC-104 form factor, allow you to mount it with other PC- 104 Modules or Single Board PC with 40 pins. connector, it can be connected directly to IDE interface. The ATA devices install as drive C: and do not require card and socket services.
ATA TO IDE INTERFACE PC-104 MODULE 1 slot for 68 Pins ATA Support Type I/II/III ATA Flash, ATA HDD, Compact Flash Cards(an adaptor required) Operating Temperature: 0 o C - 70 o C 1 slot for 50 Pins C.F. Cards Support Compact Flash Cards Operating Temperature: 0 o C - 70 o C 1 slot for 50 Pins C.F. Cards Support Compact Flash Cards Type I/II Operating Temperature: 0 o C - 70 o C PCMCIA (ATA) and compact flash (ATA) to standard IDE interface. 1Slot for 68 pins ATA and slot for 50 pins C.F. Cards. 40 pins IDE and 4 pins power connection. Support TYPE I/II/III ATA Flash, ATA HDD, Compact Flash cards. Power Consumption : 5V, 70Ma Typical.