Copper Pre-terminated Assemblies

Copper Pre-terminated Assemblies

Copper Pre-Terminated Trunk Assemblies Overview Copper Pre-Terminated trunk assemblies are the perfect solution for Enterprise / Premise & Data Centre applications where speed of installation is important. Factory termination and testing simplify installation, saving time and labour when compared to field terminated installations. Bespoke configurations in pre-engineered lengths with connectors to meet the specific needs of each application. Assemblies are typically built with a choice of 6 or 12 cable bundle using LSZH jacket. Standards compliant premium connectors and cable are used to ensure the best possible headroom and performance. Testing All preterms are 100% factory tested using the latest tier 3 tester; hard copy results for each link are packed with every preterm. Soft copy results are available upon request. Components We only use premium components for the production of our copper pre-terminated trunk assemblies to ensure the highest possible headroom. Construction Trunk assemblies are supplied in bundles of either 6 or 12 cables. A braided sleeve is applied to preterms up to 15mtrs in length and break out points are secured with heat shrink. Each link is labeled with corresponding port numbers as standard bespoke labeling requirements can be arranged at the time of order. Assemblies above 15mtrs will be bundled together using hook and loop tie wraps. Packaging Each preterm breakout is covered with a bubble wrap pocket to ensure protection of connectors during transportation, each coiled assembly is then packed and heat sealed into a PE bag and test results attached. Long length assemblies will be coiled and supplied in a cardboard box. 2 www.optronicsnet.com

Contents Warranty Programme 4 Page INSTALLATION TIME REDUCED Copper Pre-terminated Trunk Assemblies Overview 5 Application Scenarios 6 Pre-terminated Solutions 8 Configuration Guide 9 Bespoke Patch Cords / Drop Cables 10 Accessories 11 QUICK MOVES, ADDITIONS AND CHANGES HIGH DENSITY VERSIONS AVAILABLE Copper Pre-terminated Assemblies Brochure 3

1Typical Application Scenario Enterprise / Premise Jack - Surface Box 1 Jack - Jack 2 Jack - Plug 3 Jack - Open End 4 1 2 3 4 Jack to Jack Ideal for fast installation of the permanent link, panel to panel application requires the use of an empty keystone panel frame (400-001) supplied separately. Patch cords would then be used to complete the channel between active equipment (i.e. servers and switches). Jack or Plug to Open End Used in applications similar to the Jack-to-Jack configuration, but one end would be terminated to a PCB panel instead of an unloaded keystone panel. This termination type requires field testing of the drops after the cables have been terminated. Jack to Surface Mounted Box Ideal for simple moves, adds and changes on the office floor, the jacks are installed into a 400-001 unloaded panel frame and patched into the relevant active equipment. The surface mounted box can be positioned into the desired location in the work area where users PC s can be patched into the network. Jack to Plug Eliminates one cross-connect point by installing the RJ45 plug directly into the active equipment (i.e. switches). The keystone jack termination snaps into the 400-001 unloaded panel, which would then be patched to other active equipment or work area ports as necessary. 4 www.optronicsnet.com

2Typical Application Scenario Data Centre Jack - Plug 1 LGX - Plug Jack - Jack 2 LGX - LGX The Keystone LGX is a 6 way cassette to enable installation of keystone jacks into our 1U sliding panel S13XXX00 (up to 18 ports) or the 3U Chassis (up to 84 ports). This system can also be combined with any of our Fibre LGX configurations allowing a mixture of copper and fibre in one panel. This solution is perfect for data centre applications where high density installations are a must. 1 LGX to Plug The LGX Plug assembly eliminates one cross-connect point by installing the RJ45 plug directly into the active equipment (i.e. switches). 2 LGX to LGX Ideal for fast installation of the permanent link, panel to panel application. Patch cords would then be used to complete the channel between active equipment (i.e. servers and switches). Copper Pre-terminated Assemblies Brochure 5

An overview to the Copper pre-terminated trunk assemblies Pre-terminated Solutions 6 1 2 3 4 5 6 7 Jack to Jack Jack Jack to Plug Jack Jack to Open End Jack Plug to Open End Plug LGX to LGX LGX Module LGX to Plug LGX Module LGX to Open End LGX Module www.optronicsnet.com

Jack Plug Open End Open End LGX Module Plug Open End Copper Pre-terminated Assemblies Brochure 7

An overview to the Copper pre-terminated trunk assemblies Configuration Guide Connector End A Cable Distribution Connector End B Keystone Jack Unscreened (Female) Cat 5E UTP Staggered Keystone Jack Unscreened (Female) Keystone Jack Screened (Female) Cat 5E FTP Fan Out Keystone Jack Screened (Female) RJ-45 Plug Unscreened (Male) Cat 6 UTP RJ-45 Plug Unscreened (Male) RJ-45 Plug Screened (Male) Cat 6 FTP RJ-45 Plug Screened (Male) Open End Cat 6A U/FTP Open End Part Number Generator QTCT Cable Bundle Screen Lenght (m) End A End B 5E 5E 06 U/UTP UT 10 10L Jack K Jack K C6 C6 12 F/UTP FT 12 12L Plug R Plug R 6 A 6A 14 14L Open O 16 16L 18 18L Example Part Number: 20 20L QTCT C6 12 UT 16L K R QTCTC612UT16LKR has created a CAT 6 UTP 12 way jack - plug copper trunk 16 mtrs Please Specify exact length requirement and distribution requirements (Staggered or Fan out) upon ordering. For individual cable and component performance and technical data please view relevant data sheets. 8 www.optronicsnet.com

Complementary products Bespoke Patch Cords / Drop Cables Optronics can offer a quick turn around solution for copper patch cords and drop cables. Our UK production facility is geared to satisfy customer requirements for fully bespoke patch cords. Service Features > > Bespoke lengths > > Rare colour options > > Special pin configurations > > Special labelling / packaging requirements > > No MOQ > > Quick Turn around production Drop Cables allow connection and access to and from the trunk cables of a network such as the cables that connect individual PCs to the bus on a bus LAN. In a CATV system, the transmission cable from the distribution cable to a dwelling. Optronics can produce custom drop cables to satisfy your individual requirements. As standard these are produced using stranded cable for lengths up to 10mtrs and solid cable for lengths above 10mtrs. Jack (female) to Plug (Male) drop cables are available in Screened and unscreened solutions over CAT5e and CAT6. CAT6A drop cables are supplied as a screened solution only. Patch Cords Part Number Configurator QTCP 45 Cable Screen Lenght (m) Jacket 5E 5E U/UTP UT 01 PVC P C6 C6 F/UTP FT 02 LSZH L 6 A 6A 05 10 15 20 25 30 Example Part Number: Drop Cables Part Number Configurator QTCP 5E 45 UT 01 P QTCP5E45UT01P has created a quick turn copper patch lead - CAT 5E RJ-45 U/UTP up to 1 metre PVC Please Specify exact length, colour and part number configuration at time of order. DRP Cable Screen Lenght (m) Jacket 5E 5E U/UTP UT XX m PVC Where XX is the length XXM in metres C6 C6 F/UTP FT LSZH 6 A 6A Example Part Number: DRP C6 FT 10M LSZH DRPC6FT10MLSZH has created a CAT 6 F/UTP male - female 10 metres LSZH drop cable Copper Pre-terminated Assemblies Brochure 9

Complementary products Accessories LGX Style RJ-45 Keystone Jack Module This innovative and robust LGX style keystone jack module. has been designed to accept 6 unscreened or screened RJ-45 keystone jack, and deliver reliable performance upto category 6A. With the ability to use LGX style footprint, Optronics offers a unified and modular platform for both fibre and copper solution. Description Unloaded 6 way keystone LGX cassette Part Number L08XXX00 Unloaded 1U Keystone Patch Panel 24 Port Unloaded 1U 19 patch panel 24 port for mounting cat. 5e, 6 and 6a keystone jacks, it can be used for screened and unscreened solutions. Description Part Number Unloaded 1U 19 keystone patch panel 24 port 400-001 Single Gang Bevelled UK style single gang bevelled faceplate. Suitable for installing 1 to 2 ports. Dimensions: 86 x 86mm Description Part Number Single Gang Faceplate Bevelled 1-2 port 100-007 Double Gang Bevelled UK style double gang bevelled faceplate. Suitable for installing 1 to 4 ports. Dimensions: 86 x 146mm Description Part Number Double Gang Faceplate Bevelled 1-4 port 100-008 Blanks Blanks & unloaded angled module. Fits with any UK style faceplates. Description Part Number 50 X 25mm Blank 100-009 50 X 12.5mm Blank 100-010 50 X 25mm Angled module 100-006 European Angled Insert European style curved faceplate. Comes with unloaded modules in 1 or 2 port versions. Description Part Number Optronics Angled Insert 45 x 45 Single Port 200-006 Optronics Angled Insert 45 x 45 Double Port 200-007 10 www.optronicsnet.com

Warranty programme A trusted 25 year product & life application warranty Optronics offer one of the most complete warranty programmes available to the structured cabling industry. Our copper and fibre solutions are designed for performance and reliability and manufactured to comply with the latest national and international standards at the time of installation. The Optronics cabling system exceeds the performance requirements defined within ISO/IEC 11801, ANSI/EIA/TIA 568 and EN 50173, as applicable, and is warranted against manufacturing defects for a period of 25 years from the date of installation. Furthermore, FibreFab Ltd will also warrant a complete Optronics system to support for the lifetime of the installation all applications that have been designed to run on the specific CLASS/Category of cabling system for 25 years, providing that the components have been installed and tested by an Optronics certified integrator. > > Optronics cabling solutions are warranted to support all and any applications designed to operate over the installed class of cabling system > > Optronics products are warranted for a period of 25 years as being free from manufacturing defects that could jeopardise the mechanical, electrical or transmission line performance and reliability > > Warranty only available through the approved partner network > > The warranty can be transferred to new building owners The Optronics copper and fibre structured cabling range represents the relentless pursuit by the brand to bring quality and reliability to the market. Achieved through world class engineering we have confidence to stand behind our products and the applications they support for 25 years in the full knowledge that they will continue to faultlessly deliver the applications for which they were designed for a life-time. to faultlessly deliver the applications for which they were designed for a life-time. (Please refer to the Optronics 25 year warranty document for terms and conditions) Copper Pre-terminated Assemblies Brochure 11

Optronics Limited Tel: +44 (0)1908 441 121 www.optronicsnet.com Version 3.0 Copyright Optronics 2013 All Rights Reserved E&OE OPTCOPPRETERM Products are covered by GB and other patents and/or patents applied for: Pre-Terminated Cable Breakout Module, UHD Modular System and Shuttered Quad Adaptor and FirstLight is a registered trademark MTP is a registered trademark of US Conec