FLOW PATTERNS AND EXCHANGE PROCESSES IN DEAD ZONES OF RIVERS VOLKER WEITBRECHT & GERHARD H. JIRKA



Similar documents
FLUID FLOW STREAMLINE LAMINAR FLOW TURBULENT FLOW REYNOLDS NUMBER

Abaqus/CFD Sample Problems. Abaqus 6.10

HEAT TRANSFER ANALYSIS IN A 3D SQUARE CHANNEL LAMINAR FLOW WITH USING BAFFLES 1 Vikram Bishnoi

CEE 370 Fall Laboratory #3 Open Channel Flow

Backwater Rise and Drag Characteristics of Bridge Piers under Subcritical

NUMERICAL ANALYSIS OF THE EFFECTS OF WIND ON BUILDING STRUCTURES

(1) 2 TEST SETUP. Table 1 Summary of models used for calculating roughness parameters Model Published z 0 / H d/h

Experiment 3 Pipe Friction

Using CFD to improve the design of a circulating water channel

Appendix 4-C. Open Channel Theory

2D Modeling of Urban Flood Vulnerable Areas

Experiment (13): Flow channel

NUMERICAL STUDY OF FLOW AND TURBULENCE THROUGH SUBMERGED VEGETATION

du u U 0 U dy y b 0 b

Dimensional analysis is a method for reducing the number and complexity of experimental variables that affect a given physical phenomena.

Understanding Plastics Engineering Calculations

CHAPTER 9 CHANNELS APPENDIX A. Hydraulic Design Equations for Open Channel Flow

Exercise (4): Open Channel Flow - Gradually Varied Flow

Head Loss in Pipe Flow ME 123: Mechanical Engineering Laboratory II: Fluids

Optiffuser. High-performance, high bandwidth lightweight 1D diffuser.

Straits of Mackinac Contaminant Release Scenarios: Flow Visualization and Tracer Simulations

Basic Equations, Boundary Conditions and Dimensionless Parameters

How To Model A Horseshoe Vortex

What is the most obvious difference between pipe flow and open channel flow????????????? (in terms of flow conditions and energy situation)

2.0 BASIC CONCEPTS OF OPEN CHANNEL FLOW MEASUREMENT

Chapter 8: Flow in Pipes

Collision of a small bubble with a large falling particle

inter.noise 2000 The 29th International Congress and Exhibition on Noise Control Engineering August 2000, Nice, FRANCE

NUCLEAR ENERGY RESEARCH INITIATIVE

RESERVOIR CFD MODELLING WHAT ARE THE BENEFITS OF USING A 3D MODEL?

Dimensional Analysis

3. Experimental Results

Chapter 2. Derivation of the Equations of Open Channel Flow. 2.1 General Considerations

Open channel flow Basic principle

CFD SIMULATION OF SDHW STORAGE TANK WITH AND WITHOUT HEATER

Sediment Entry Investigation at the 30 Degree Water Intake Installed at a Trapezoidal Channel

Chapter 13 OPEN-CHANNEL FLOW

Chapter 10. Flow Rate. Flow Rate. Flow Measurements. The velocity of the flow is described at any

Practice Problems on Boundary Layers. Answer(s): D = 107 N D = 152 N. C. Wassgren, Purdue University Page 1 of 17 Last Updated: 2010 Nov 22

The INSEAN E779a Propeller Test Case: a Database For CFD Validation

4.4 WAVE CHARACTERISTICS 4.5 WAVE PROPERTIES HW/Study Packet

3. Mixing in Rivers: Turbulent Diffusion and Dispersion

Experimental Wind Turbine Aerodynamics

SIMULATION OF FLOW THROUGH A PUMP SUMP AND ITS VALIDATION

Use of OpenFoam in a CFD analysis of a finger type slug catcher. Dynaflow Conference 2011 January , Rotterdam, the Netherlands

Topic 8: Open Channel Flow

Open Channel Flow Measurement Weirs and Flumes

Dimensional Analysis, hydraulic similitude and model investigation. Dr. Sanghamitra Kundu

Flow Patterns in an Open Channel Confluence with Increasingly Dominant Tributary Inflow

A Measurement of 3-D Water Velocity Components During ROV Tether Simulations in a Test Tank Using Hydroacoustic Doppler Velocimeter

A fundamental study of the flow past a circular cylinder using Abaqus/CFD

Paweł M. Rowiński Institute of Geophysics, Polish Academy of Sciences, Warsaw, Poland

Choices and Applications of 2D/3D models for supporting harbour & coastal management

Flow distribution and turbulent heat transfer in a hexagonal rod bundle experiment

Effect of Aspect Ratio on Laminar Natural Convection in Partially Heated Enclosure

Numerical Investigation of Angle and Geometric of L-Shape Groin on the Flow and Erosion Regime at River Bends

Open Channel Flow. M. Siavashi. School of Mechanical Engineering Iran University of Science and Technology

O.F.Wind Wind Site Assessment Simulation in complex terrain based on OpenFOAM. Darmstadt,

Understanding Mantle Heat Exchangers Used in Solar Water Heaters

Phased-Array ROWA-SPA: High-performance testing machine for combined, 100-percent automated testing of square and round bars

AN EFFECT OF GRID QUALITY ON THE RESULTS OF NUMERICAL SIMULATIONS OF THE FLUID FLOW FIELD IN AN AGITATED VESSEL

AN ANALYTICAL MODEL FOR WATER PROFILE CALCULATIONS IN FREE SURFACE FLOWS THROUGH ROCKFILLS

OPTIMISE TANK DESIGN USING CFD. Lisa Brown. Parsons Brinckerhoff

Steady Flow: Laminar and Turbulent in an S-Bend

Experimentation and Computational Fluid Dynamics Modelling of Roughness Effects in Flexible Pipelines

Design and Analysis of Various Bluff Objects for Vortex flow meters

Contents. Microfluidics - Jens Ducrée Physics: Fluid Dynamics 1

Heat Transfer Prof. Dr. Ale Kumar Ghosal Department of Chemical Engineering Indian Institute of Technology, Guwahati

HYDRAULICS. H91.8D/C - Computerized Open Surface Tilting Flow Channel - 10, 12.5, 15 and 20 m long

ALARM SYSTEM FOR ACCIDENTAL POLLUTION ON THE RIVER RHINE

Copa Raked Bar Screen

THERMAL STRATIFICATION IN A HOT WATER TANK ESTABLISHED BY HEAT LOSS FROM THE TANK

GROUNDWATER FLOW NETS Graphical Solutions to the Flow Equations. One family of curves are flow lines Another family of curves are equipotential lines

M6a: Open Channel Flow (Manning s Equation, Partially Flowing Pipes, and Specific Energy)

Long term prediction of marble erosion for the conservation of the statue of David of Michelangelo

Ravi Kumar Singh*, K. B. Sahu**, Thakur Debasis Mishra***

Advancements in High Frequency, High Resolution Acoustic Micro Imaging for Thin Silicon Applications

Chapter 9. Steady Flow in Open channels

HEAT TRANSFER AUGMENTATION THROUGH DIFFERENT PASSIVE INTENSIFIER METHODS

EXPERIMENTAL STUDIES ON PRESSURE DROP IN A SINUSOIDAL PLATE HEAT EXCHANGER: EFFECT OF CORRUGATION ANGLE

HEAT TRANSFER ENHANCEMENT IN FIN AND TUBE HEAT EXCHANGER - A REVIEW

Index-Velocity Rating Development for Rapidly Changing Flows in an Irrigation Canal Using Broadband StreamPro ADCP and ChannelMaster H-ADCP

Aeroacoustic simulation based on linearized Euler equations and stochastic sound source modelling

Performance prediction of a centrifugal pump working in direct and reverse mode using Computational Fluid Dynamics

XI / PHYSICS FLUIDS IN MOTION 11/PA

FLOW CONDITIONER DESIGN FOR IMPROVING OPEN CHANNEL FLOW MEASUREMENT ACCURACY FROM A SONTEK ARGONAUT-SW

AS COMPETITION PAPER 2008

Optical Design Tools for Backlight Displays

DEVELOPMENT OF HIGH SPEED RESPONSE LAMINAR FLOW METER FOR AIR CONDITIONING

Turbulence Modeling in CFD Simulation of Intake Manifold for a 4 Cylinder Engine

Basic Principles in Microfluidics

Keywords: Heat transfer enhancement; staggered arrangement; Triangular Prism, Reynolds Number. 1. Introduction

Correcting the Lateral Response Artifact in Radiochromic Film Images from Flatbed Scanners

4.3 Results Drained Conditions Undrained Conditions References Data Files Undrained Analysis of

Fluid Dynamics Basics

A. Hyll and V. Horák * Department of Mechanical Engineering, Faculty of Military Technology, University of Defence, Brno, Czech Republic

A PHOTOGRAMMETRIC APPRAOCH FOR AUTOMATIC TRAFFIC ASSESSMENT USING CONVENTIONAL CCTV CAMERA

Application of CFD Simulation in the Design of a Parabolic Winglet on NACA 2412

Transcription:

FLOW PATTERNS AND EXCHANGE PROCESSES IN DEAD ZONES OF RIVERS VOLKER WEITBRECHT & GERHARD H. JIRKA Institute for Hydromechanics, University of Karlsruhe 76128 Karlsruhe, Germany weitbrecht@ifh.uni-karlsruhe.de ABSTRACT This paper presents the results of an experimental work conducted in the framework of a research project that deals with the effect of dead zones (groyne fields, harbours) on the longitudinal dispersion in rivers. The objective is an improved prediction of travel time, maximum concentration and skewness of a tracer cloud than is possible with existing alarm models. The exchange processes between main stream and dead zones have major influence on the longitudinal stretching of a tracer cloud traveling down a river. The main physical process that governs the exchange of dissolved matter between the dead zone and the main stream are coherent two-dimensional structures that are generated at the head of a groyne. These structures are growing in horizontal direction during their travel between two groynes because the flow is very shallow. Planar velocity measurements with PIV (Particle-Image-Velocimetry) have been performed in a large shallow water table (5.5 m x 15 m) at the Institute for Hydromechanics at the University of Karlsruhe to analyze the turbulent flow characteristics in a river in the presence of groynes. The mass exchange is related to the aspect ratio (width/length) of a dead zone and to the position of the groynes in relation to the main flow direction. With the aid of PIV it is possible to measure instantaneous velocity fields with a high spatial resolution so that the coherent structures which are mainly responsible for mass exchange can be determined by calculating vorticity fields. These measurements give detailed insight to the mean flow conditions and the turbulent flow characteristics in the dead zones. In a further step a dimensionless mass exchange parameter as has been defined by Valentine & Wood (1977) was extracted from the velocity data. KEY WORDS Longitudinal dispersion, recirculating flows, particle-image-velocimetry INTRODUCTION Accidental pollution spills of dissolved matter in rivers occur frequently. The knowledge of how fast these pollution clouds get transported and dispersed is of great importance. As a result of the Sandoz accident in 1986 where a large amount of toxic chemicals were released into the river Rhine the International Commission for the Hydrology of the River Rhine (CHR) developed a prediction model (Spreafico & Mazijk 1993) for travel times and maximum concentrations for such accidental scenarios. For this kind of predictive model, much effort and funding must be spent on calibration by means of extensive tracer measurements. In case of the river Rhine-Alarm-Model which uses a one-dimensional analytical approximation for the travel times and the concentration curves, a dispersion coefficient and a lag coefficient have to be calibrated. If this calibration procedure is complete the model works well for cases of similar hydrological situations. However, variations in discharge and thus

changes in water surface level lead to increased errors if the same calibrated parameters are used for different hydrological characteristics. Dead zones along the flow path of a river such as groyne fields, harbors and side channels have a major influence on the longitudinal dispersion in rivers. Exchange processes between dead zones and the main channel influence the transport velocity of the tracer cloud and also the dispersive character of the flow due to fact that dissolved material gets trapped in such dead zones. This leads to a certain lag of the tracer cloud in comparison to the mean flow velocity in the main channel and hence to additional longitudinal dispersion. For regular channels with known spanwise velocity distribution, the one-dimensional longitudinal dispersion can be predicted with the aid of Fischer s theory (Fischer 1979), where the expression of Elder (1959) for horizontal shear flow in channels is extended for natural rivers with horizontal velocity distribution. To determine the effect of additional dispersion due to exchange processes between dead zones and main stream, it is of great interest to know the behavior of the flow dynamics in a river in the presence of dead zones. Due to the fact, that the flow is very shallow, which means that the horizontal dimension of the flow is much larger than the vertical, large coherent structures emerge at the head of a groyne. These structures are responsible for the mass transport between the main stream and the dead zone. With the aid of PIV (Particle Image Velocimetry) measurement technique, it is possible to detect these structures because this technique provides a view of the instantaneous velocity fields. In addition, the knowledge of flow velocities at every single point allows to calculate the instantaneous rate of mass exchange. EXPERIMENTS The Institute for Hydromechanics is equipped with a shallow water table that has a smooth horizontal bottom and dimensions of 15 m long and 5.5 m wide (Fig. 1). A uniform flow with water depth of 4.6 cm and mean flow velocity about 0.16 m/s was regulated with the aid of a diffuser and damping screens at the inlet region of the tank. The Reynolds Number based on water depth in the main flow region is therefore in the order of 7500. In order to simulate the flow in typical dead zones, a series of 15 groynes made of Perspex with a heavy core are produced, so that these elements can be placed at variable positions. The shape of the groynes was chosen to be very simple due to the fact that earlier investigations suggest that there is no significant effect of the groynes shape to the exchange processes (Lehmann et al. 1999). The outline of the groynes is a combination of a rectangular box (0. 5 m x 0.05 m x 0.05 m) with an attached half cylinder (diameter = 0.05 m). 15 m W W/L = 0.34 L 0.4 0.48 W/L = 0.59 0.77 1.11 2.00 3.33 5 m α W/L = 0.40 W/L = 1.11 α = + (10, 18, 26 ) α = + ( 10,26), + 18 Inlet with diffusor Damping screens 3-D positioning system Fig. 1: Top view of shallow water table with schematized groyne fields Fig. 2: Schematized illustration of all tested formation

In this study, the influence of the aspect ratio (width/length of groyne field) and the angle between the groyne and the main flow direction is analyzed. It could be shown, that for typical European rivers the aspect ratio lies in the range of 0.3 1.1. The mean value for the River Rhine is about 0.5 whereas for the Dutch river Waal it is 0.3. In Fig. 2 all the situations that have been tested are illustrated. Additional experiments with smaller aspect ratios will be conducted in the near future. In a second step, the inclination angle of the groynes to the flow direction was varied for two cases (W/L = 0.40 and 1.11). These values are shown in Fig. 2 and are typical for the River Elbe. The measurement technique used in this study is based on a PIV-System (LaVision), which has been adapted so that a flow field of 1.2 m x 1.4 m could be observed with a high spatial resolution leading to a 60 x 84 vector matrix. The time resolution of 7 Hz is provided by a PCO-Sensicam camera (12 Bit, 1024 x 1280 pixels). A NIKON lens (f-mount) with a focal length of 14 mm is used for an undistorted high quality image. The quality of the velocity measurements with PIV technique highly depends on the optical and physical properties of the particles that are put on the water surface to trace the flow. They must give a strong contrast to the white bottom, the density must be just below the density of the water, and the size has to be in the order of 2-3 mm. Good visualization can be obtained with black polypropylene particles with a special coating to prevent sticking together. Another important requirement for a successful measurement is the distribution of the observed particles on the water surface. The particles have to be distributed uniformly in every subdivision (AOI, Area of Interest) of the flow field. Therefore a particle dispenser (Fig. 3) has been designed, that uses a roller brush within a vibrating silo to scatter the particle homogeneously. Top view Silo Side view PIV-Camera silo with particles Roller brush Groyne Fig. 3: Experimental setup for PIV measurements at the water surface with particle dispenser Every situation has been measured three times for about 30 seconds with 7 Hz, so that the statistics are based on 600 velocity fields. The time scale of the large structures is in the order of 5 to 10 seconds. Due to the fact, that one frame contains a data size of 2.5 MB, this configuration requires a PC with at least 1 GB RAM capacity. Otherwise a single time series would have to be much shorter and it would be impossible to track the large scale coherent structures.

VELOCITY FIELDS With the aid of the PIV measurement technique, it is possible to get detailed information about the mean flow velocities and the turbulent characteristics of the flow. In this study we are talking only about low frequency turbulence because these phenomena are dominant in the sense of mass transfer. The following pictures show the streamlines which are generated out of 600 velocity fields. In general the mean flow in a groyne field is dominated by a single large RESULTS eddy (Fig. 4, W/L = 1.11). For aspect ratios of less than 0.5 a second eddy emerges in the upstream corner of the groyne field. For aspect ratios larger than 1.5 the main eddy is splitting into two in the transverse direction. Similar phenomena have been observed by Booij (1986) and Uijttewaal (1999), respectively. In order to analyze the exchange processes, it is of great importance to observe the dynamics of the flow. With simple dye tests (Fig. 5), it can be shown, that the region between the W/L = 0,34 W/L = 1.11 1 2 W/L = 0.40 W/L = 2.00 Fig. 4: Measured mean flow conditions in groyne fields with different aspect ratio Fig. 5: Visualization of coherent structures that are responsible for mass exchange groyne field and the main stream is very dynamic. Large structures are generated at the head of a groyne and are growing in the horizontal direction. The path of these structures is not always the same. Sometimes they get trapped in the dead zone and sometimes they travel further downstream without any additional influence of the particular dead zone. This mechanism governs the mass exchange between main stream and dead zone. The interpretation of exchange processes must be done with the help of instantaneous velocity fields. In Fig. 6 the instantaneous velocity field is plotted in comparison with the corresponding vorticity field. It can be seen that a large structure starts to travel downstream. At this instant it is not obvious if it is going to penetrate fully, partly or not into the groyne field. The vorticity field shows clearly the clockwise rotation of the large structures in the mixing layer. Shear and therefore vorticity is also generated at the groynes and in the shear zone between the two eddies. Here the rotation is mainly anticlockwise

Fig. 6: Instantaneous velocity field and vorticity field (dark color strong anticlockwise rotation and white color strong clockwise rotation) Main stream h Groyne field Fig. 7: Transverse rms-velocity (max. value = 0,026 m/s (white), mean velocity in main stream = 0,2 m/s) A s E A b Fig. 8: Schematic cross sectional view of river with dead zone In order quantify the mass exchange between main stream and groyne field, the instantaneous transverse velocities were analyzed. In Fig. 7 the velocity fluctuations (rms-velocity) in transverse direction are plotted. Point measurements with Laser-Doppler-Technique showed, that these results are reliable. In this example it can be seen, that the highest turbulent intensities can be found in the mid section between the two groynes. EXCHANGE PROCESSES Longitudinal dispersion in rivers is often modeled with one-dimensional dead zone model where the one-dimensional advection diffusion equation is linked with a second exchange C b equation = D b (Cs C b ) which describes the concentration in the dead zone (Schmid t 1999). C b is the concentration in the dead zone, C s the concentration in the main stream and D b an exchange coefficient. D b is defined by D b = (h/a b ) E with A b the cross sectional area and E the exchange velocity between the dead zone and the main stream (Fig. 8). Normalization of the exchange coefficient D b with the mean velocity of the main stream and the width of the groyne field gives a dimensionless exchange coefficient k (Valentine & B Db Wood, 1977) k =. U s

Since the exchange velocity E can be directly observed in the experiments, the dimensionless exchange coefficient can be determined (Fig. 9). Account should be taken of the fact, that the velocities are measured at the water surface and do not represent the depth averaged velocity. It can be seen that the exchange gets smaller if the aspect ratio increases. For very large aspect ratios the exchange coefficient starts to increase again. This phenomenon is not related to the actual mass exchange but to oscillation effects. The whole water body in the dead zone starts to swing back and forth which leads in this case to additional virtual exchange. Fig. 9: Exchange parameter k in relation to aspect ratio CONCLUSIONS Exchange processes between dead zones and main stream are governed by large coherent two-dimensional structures which are generated at the head of a groyne. These structures can be quantified with PIV-measurements at the water surface if adequate particles are chosen and the distribution of these particles is homogeneous. It is possible to determine the mass exchange with the aid of velocity measurements. The mass exchange is related to the aspect ratio of a dead zone and, in case of groynes, of the angle between the groyne and the main flow direction. In case of high aspect ratios oscillation effects occur, which are not part of the actual mass exchange. ACKNOWLEDGMENTS The authors would like to thank G. Kühn and K. Schmidhäussler for their help in performing the experiments. The project is sponsored by the German Bundesministerium für Bildung und Forschung (Grant No. 02 WT 9934/9). REFERENCES: Elder, J. (1959), The dispersion of marked fluid in turbulent shear flow. J. Fluid Mech. 5 Booij, R. (1989), Exchange of mass in harbours, Proc. 23th, IAHR Congresss Ottawa Fischer, H.B., List, E.J., Koh, R.C.Y., Imberger, J. and Brooks, N.H. (1979), Mixing in Inland and Coastal Waters, Academic Press, New York Lehmann, D. W. Uijttewaal, A. van Mazijk, V. Weitbrecht, (1999),Auswirkung von Buhnenfeldern auf den Transport gelöster Stoffe in Flüssen, TU-Delft, Dept. of Fluid Mechanics Schmid, B. (1999), Analytic Solution of the Transient Storage Equations Accounting for Solute Decay, Proceedings 28 th IAHR Congress, Graz, Austria Spreafico, M. and A. van Mazijk (1993), Alarmmodell Rhein. Ein Modell für die operationelle Vorhersage des Transportes von Schadstoffen im Rhein. Bericht Nr. I-12, Kommission für die Hydrologie des Rheins, Lelystad Uijttewaal, W. (1999), Groyne Field Velocity Patterns determined with particle tracking velocimetry, Proceedings 28 th IAHR Congress, Graz, Austria Valentine, E.M. Wood, I.R. (1977), Longitudinal dispersion with dead zones, J. Hydraulics Division, 105(HY8),pp 999 Wallast, I., Uijttewaal, W., Mazijk, A. van, (1999), Exchange processes between groyne field and main stream. Proceedings 28 th IAHR Congress, Graz