NETWORK MONITORING WITH C

It Pays To Ensure Security And Protection... NETWORK MONITORING WITH C The Rittal CMC offers a perfect, complete solution for network monitoring and security. There is an impressive range of benefits all of which are geared towards ensuring total system security. 1 FUNCTIONAL BENEFITS 2 COST BENEFITS 3 CONTROL BENEFITS Standard default settings mean that the CMC is ready to use immediately. The CMC equipment, both local and remote, can be administered centrally. Password protection is provided for the serial interface. There is nothing more costly than a system shutdown! You can help prevent this with the Rittal CMC enclosure monitoring system an important factor in limiting the risk of failure. Risk of failure Permanent CMC monitoring of numerous potential hazard sources significantly reduces the risk of a network failure and damage to expensive components. Investments Replacement investments can prove extremely costly in the event of a network failure. Weigh this up against the price of a cost-effective, PC-based Rittal CMC solution. Plain text display and LEDs on the CMC indicate the operating status and any possible faults. With network management software (SNMP/ Telnet), messages are portrayed on a network computer via an interface. This allows permanent monitoring of several connected enclosures from a single central control center. The parameters and terms can be set individually. CMC CMC PARIS TCP/IP Router TCP/IP CMC CMC CMC SNMP Remote control: Thanks to bidirectional data communication with the CMC, many of the enclosure s functions can be remotely communicated and controlled from the control center. 55

MC Complete Solutions CMC base unit Large range of accessories to complement the unit Own management software on Windows 95 NT Sensors for temperature, humidity, smoke and vibration monitoring Coded lock system Control of network voltage Competent Rittal service from planning through to assembly. Clear: Just two LEDs in three states: Green no malfunction; orange warning; red malfunction Always in view: The following are indicated in green: Link Connection to the network via 10BaseT interface. Traffic Data traffic on the network. Com Data exchange between the CMC/PC. PC interface: RJ 11 jack RS 232 for entering variables and inquiring status via the PC (menuassisted). The CMC speaks your language: The temperature is shown in the first line of the LCD display. The second line alternately shows the mains voltage, two analog values (in %) and the current fault in the form of a text message. Text messages may be freely selected. Easy handling: Switching values are set and the ten most recent error messages can be retrieved using three keys: Change To branch to a menu. Enter To select the various functions. C To acknowledge error messages. The acoustic alarm can likewise be acknowledged. 4 OPERATING BENEFITS The system parameters can be directly set using the front control keys, via a PC interface, SNMP or Telnet. The status can be retrieved on the display or PC screen at any time in plain text format. 56

Sensors, Lock Systems, Accessories & More... CMC SYSTEM BASICS 1 SENSORS Temperature sensor Promptly detects and avoids risks to components caused by temperature rises inside the network enclosure. Smoke alarm sensor The smoke alarm sensor facilitates the early detection of smoke inside the network enclosure. Hygro-thermosensor For monitoring relative air humidity/ temperature within the set limits. Vibration sensor Thanks to an adjustable level of sensitivity, it is possible to identify vibrations of varying intensity. Entry sensor Unauthorized access to the network enclosure is indicated and reported. Lock System 2 LOCK SYSTEMS Ergoform-S with electromagnetic lock The lock unit consists of a Rittal Ergoform-S with an electromagnetically locked swing lever. Ergoform-S with electromagnetic lock for QuickRack A new extra option for this economical enclosure variant. Security lock For locking PS doors with tubular door frames. Universal lock unit Consisting of a base unit (controlled via the CMC) and a lock counterpart. Smart card reader The smart card reader operates as a central unit to release the door. Magnetic card reader The magnetic card reader is supplied with three magnetic cards, each with a different four-digit code. General Accessories 3 GENERAL ACCESSORIES CMC socket strip Equipped with interference suppression filter and overvoltage protection. Junction box with mounting bracket For systemcompatible mounting in network enclosures. Cable ties The fast solution for fixing cables to the enclosure section or to mounting system parts. Nylon loop For problem-free release of attached cables or the addition of individual cables. Hygrostat Reports when a humidity alarm level is exceeded. Door-operated switch To report opening of a network door. 57

Keyboard lock Four-digit numbers may be authorized in the CMC. The entered code is transmitted to the CMC via the I 2 C bus. Connection Modules At-A-Glance Packs of Part No. 1. Connection technology 115V power cord 1 3686338 Programming cable 1 7200221 Connector kit for connecting accessories 1 kit 7200223 Cable for sensor connection, 10m 1 9966831 24V power pack 1 7200240 Cable clamp strap, narrow 1 7610000 Cable clamp strap, wide 1 7611000 Interference suppression capacitors for fans 20 7200490 I 2 C booster 1 7200600 2. Cable management Cable management module, mounting kit 1 7200400 Cable management module with plug-in system 1 7200411 *Accessories for connection cable RJ 11 4 7200420 *Accessories for connection cable RJ 12 4 7200430 *Accessories for extension cable RJ 11 4 7200440 *Accessories for extension cable RJ 12 4 7200450 3. Sensors Temperature sensor 1 7200300 *Temperature sensor w/connection cable & connector 1 7200301 Smoke alarm sensor 1 7200310 *Smoke alarm sensor w/connection cable & connector 1 7200311 Hygro-thermo-sensor 1 7200360 *Hygro-thermo-sensor w/connection cable & connector 1 7200361 Vibration sensor 4 7200320 *Vibration sensor w/connection cable & connector 4 7200321 Access sensor 4 7200330 *Access sensor w/connection cable & connector 4 7200331 4. Lock system / access protection Ergoform-S, electromagnetic lock 1 7200350 *Ergoform-S, electromagnetic lock with connector 1 7200351 Ergoform-S, electromagnetic lock for QuickRack 1 7200650 PS locking bar H = 2000mm 1 7200371 Security lock 24V DC 1 2418000 Security lock 120V AC 1 2419000 Universal lock unit 1 7200610 Adaptor for PC reader units 10 7200345 Adaptor for VR reader units 10 7200344 Smart card reader 1 7200340 *Smart card reader w/connection cable & connector 1 7200380 Magnetic card reader 1 7200341 *Magnetic card reader w/connection cable & connector 1 7200381 Coded lock 1 7200342 *Coded lock w/connection cable & connector 1 7200382 5. General accessories CMC socket strip with monitoring 1 7200630 CMC alarm signal lamp 1 7200620 Junction box 1 7280035 Cable ties for quick assembly 100 2597000 Nylon loop, 130mm 10 7072220 Nylon loop, 200mm 10 7072230 Nylon loop, 300mm 10 7072240 Hygrostat 1 3118000 Door-operated switch 1 4127000 * For use with 7200411 58

CMC Network Monitoring Software Rittal CMC Manager Rittal s own management software runs under Windows 95/NT. Simply enter the required IP address, and the connection can be made immediately. As you would expect, the CMC Manager also includes a trap receiver which documents the alarms of all available CMCs in the network with the date, time, address and name. Here are just a few of the convenient functions offered by this SNMP program: The CMC s management information base (MIB) is incorporated into the software and included in the graphical structure. The mains voltage value is graphically portrayed. The temperatures and any analog input values are graphically portrayed. The setpoints of the CMC can be modified directly. Photographs may be incorporated in order to personalize the software. These are configured with control fields in a setup menu. The interface texts may be designed individually. The alarm trap messages may be linked to a WAV file, so that the administrator receives an acoustic warning. Other EXE or BAT files can also be appended to the trap messages, in order to initiate counteractive action automatically. The CMC manager allows continuous data recording for up to 10 devices. The CMC manager monitors the direct availability of all CMCs with the live check function. HP Open View Network Management System SNMP management programs such as HP Open View allow the CMC to be incorporated and addressed via SNMP. The required MIB is included on disk. The MIB is easily incorporated by simply copying. The MIB-II standard (RFC 1213) is also supported and is included with the supply of the NMS. The private MIB contains all values, statuses, settings and setpoints, and may conveniently be linked to the functions of the HP Open View software. Cabletron SPECTRUM Enterprise Manager Management System The graphical user interface for the SPECTRUM Enterprise Manager covers every conceivable requirement. The MIB variables are arranged on the interface in a user-friendly configuration. This professional software package combines the highlights of the CMC monitoring system with the best features of the Cabletron product. Additional modules also allow the alarm trap messages to be relayed via voice mail. The user is notified of the event by telephone, giving details of the date, time and place. The trap function can also be incorporated into the SPECTRUM Element Manager. 59

Programming Software For CMC Extension Units The programming software (Windows 95/NT) permits user-friendly configuration and logical operation of the CMC extension units. Two extension cards are available for the CMC. A user-friendly configuration software package is included with the supply, in order to facilitate logical linking of the inputs and outputs. AND, OR, NOT and TIME elements may be used. The graphical interface runs under Windows 95/NT and is easy to use. The logic may be transmitted to the CMC in the network via TFTP or directly via the RS 232 interface. TELNET The CMC menu program can be activated via TELNET (VT 100). Settings and inquiries may be implemented. The CMC menu software and the TELNET server become active upon startup of the CMC. Terminal Via Serial Interface The CMC menu program can be activated via standard terminal programs. Settings and inquiries may be implemented. The CMC menu software becomes active upon start-up of the CMC. 60

R CMC Network Monitoring Unit Link Traffic Com Computer Multi Control 1 2 3 4 5 6 1 2 So clear: Just two LEDs in three states: Green No malfunction Orange Warning Red Malfunction Always in view: The following actions are displayed in green: Link Existing network connection via 10BaseT interface. Traffic Data traffic on the network. Com Data exchange between the CMC and PC (via RS 232). 3 4 PC interface: RJ 11 jack RS 232 for entering variables and inquiring statuses via the PC (menu-assisted). The interface cable for the serial PC interface D-Sub 9 is included with connector kit DK 7200220. The CMC speaks your language: The temperature is shown in the first line of the LCD display, while the second line alternately displays the mains voltage, two analog readings in [%], and any current malfunctions in the form of a text message. These text messages may be freely defined. 5 6 Easy to operate: Switching values are set and the ten most recent error messages can be retrieved using three keys: Change To branch to a menu. Enter To select the various functions. C To acknowledge error messages. The acoustic alarm is acknowledged. Acoustic alarm: A piezo signal generator reports an alarm. Of course, this is also switchable. Network Connection / Settings Via The CMC Menu Program From a central location, an administrator can monitor all network and server enclosures in internal networks and even in external networks (via WANs), initiate any servicing required, or implement settings on the CMC. German utility model no. G 296 22 718 German reg. design no. M 97 05 717 Danish design no. MR 00534 Norwegian design no. 74617 Austrian design no. 28798 UK reg. design no. 2070680 IR reg. design no. DM / 042 821 with validity for BE, CH, ES, FR, IT, NL Indian design no. 175179 CMC Computer Multi Control with 512 KB flash-rom program memory Packs of Rittal CMC network monitoring system, 1U, with Ethernet network interface and SNMP, Telnet (10Base2/10BaseT), RS 232 With new network functions: 4 trap receive IP addresses 1 7200100 Programming and software update via Trivial File Transfer Protocol (TFTP) RS 232 access via password only Greater network security with SNMP via authorization check Alarm messages via ISDN with Vds protocol available on request. For the CMC DK 7200100, the extension units additionally allow the provision of up to 16 temperatures, 16 digital inputs and 4 relay outputs. 61

EXT 10BaseT 10Base2 I 2 C Analog Input Digital Input Relay1 Relay2 Alarm Power Fan1 Fan2 Out / In 100 240 V 50/60 Hz 20 VA Power / UPS 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 RJ 12 jack Serial interface for additional extension of the CMC for future use. RJ 45 jack Integral Ethernet interface to IEEE 802.3 via 10BaseT. RJ 45 jack For use with I 2 C extension units. Analog inputs 10-pole connector for two temperature sensors, two times 4 20 ma and extension via I 2 C bus. Technical Information Dimensions Temperature range Processor Main memory Program memory Rated voltage Rated consumption Permissible voltage drop time Internal CMC power pack output Serial interface Ethernet connection Optical/acoustic displays Input Digital inputs (power requirement per input: 7 ma) Analog inputs 5 6 7 Digital inputs 20-pole connector for seven input signals (floating contacts) and 24V DC voltage source. Relay 1 Changeover contact 250V AC, 5 A as standard for heater. Relay 2 Changeover contact 250V AC, 5 A as standard for latch mechanism. 1U, 482.6 mm (19 ) rack mount with 105mm installation depth +5 C to +45 C AM186-(20 MHz), 16-bit CPU, Intel-compatible 512 kb 16-bit DRAM 256 kb flash EPROM 100 to 240V AC, 50/60 Hz, IEC 320 socket 20V A max. 10 ms 24V DC, max. 100mA RS 232 for programming / linking to a PC 10BaseT, IEEE 802.3 (10 MB/s), TCP/IP, SNMP, TELNET 5 LEDs, LCD display with 40 characters, piezoelectric signal generator 3 membrane-sealed keys 7 (vibration/smoke/door/swing lever/reader unit/ups1/ups2) 4 (temperature 1/2 and 2 current inputs 4 20mA) Monitoring functions 3 (mains voltage, fan current 1, fan current 2) Relay outputs 3 (fan 1/2) 3 A / 250V, normally open contact Relay outputs 3 (heater/lock/alarm) 5 A / 250V, changeover contact Extension I 2 C bus and CMC-EXT Alarm relay Changeover contact 250V AC, 5 A. Each error message can be set to initiate activation of the alarm relay (freely configurable). Fan relay 12-pole connector with mains voltage monitoring and two relays for fans. Voltage supply The CMC is supplied with voltage via the IEC 320 socket. Cable clamping/ The 2 screws are designed for cable clamp rails DK 7610000/DK 7611000. Monitoring And Control Functions Fan control circuit 1 Analog input for temperature sensor 1, relay for fan 1 Fan control circuit 2 Analog input for temperature sensor 2, relay for fan 2 Heater control circuit (See temperature sensor 1/2), relay for heater Temperature monitoring 1 (See temperature sensor 1), max./min. temperature values Temperature monitoring 2 (See temperature sensor 2), max./min. temperature values Voltage monitoring Analog input (for mains voltage) Free analog sensor input 1 Analoger input 4 20mA with limit monitoring Free analog sensor input 2 Analoger input 4 20mA with limit monitoring Vibration monitoring Digital input (parallel connection possible) Smoke monitoring Digital input (parallel connection possible) Door/access monitoring Digital input (series connection possible) Door locking control Digital input for Ergoform-S swing lever (series connection possible) Door locking control Digital input for reader units Relay for Ergoform-S handle or other lock systems Monitoring of UPS 1 Digital input (parallel connection possible) Monitoring of UPS 2 Digital input (parallel connection possible) Alarm output Freely programmable relay alarm output 8 9 10 11 62

CMC Extension Unit I 2 C Bus CMC Extension Unit, Temperature An extension unit for 8 additional temperatures may be connected to the CMC DK 7200100. Alarm limits may be preset for all temperatures. Limit violations are reported via the base unit with SNMP. Eight RJ 12 jacks are provided for the connection of temperature sensors. Temperature inputs: 8 x NTC (DK 7200301) Rated voltage: 24V DC Rated current: 140mA Interface: I 2 C, max. cable length 2m CMC extension unit 8 x temperature inputs 7200911 The following are additionally required for connection to the base unit DK 7200100: Cable for 24V, 7200230 Cable for bus connection, 7200450 Connector kit for base unit, 7200220 Cable clamp strap, 7611000 24V power pack for voltage supply, 7200240 NTC temperature sensors with RJ 12 connectors, 7200301 CMC Extension Unit, I /O + Temperature Up to two extension units, each with 4 additional temperatures, 8 digital inputs and 2 relays, may be connected to CMC DK 7200100. Alarm limits may be preset for all temperatures. Limit violations or alarms are reported via the base unit with SNMP. Temperature inputs: 4 x NTC (DK 7200301) Digital inputs: 8 (supply 24V DC per 7mA) Relay outputs: 2 (changeover contacts 5 A / 250V) Rated voltage: 24V DC Rated current: 140mA Interface: I 2 C, max. cable length 2m CMC extension unit 4 x temperature inputs 8 x digital inputs 7200913 2 x relay outputs The following are additionally required for connection to the base unit DK 7200100: Cable for bus connection, 7200450 Cable for 24V/sensor connection, 7200230 Connector kit for base unit, 7200220 Cable clamp strap, 7611000 24V power pack for voltage supply, 7200240 NTC temperature sensors with RJ 12 connectors, 7200301 CMC 2 U Acccessory Unit Supplied without CMC 2U Accessory Unit With the plug and play compatibility system, the CMC accessory unit is simply fitted into the 482.6mm (19") section, and voila! It contains two fans and is installed in the uppermost position of a network enclosure. The roof plate of the enclosure must be equipped with vent holes. The unit is fully wired and a CMC (DK 7200100) is simply integrated into the bottom section. The CMC basic module is not included with the supply of the unit. The unit contains a number of functions, which are listed below: Functions of the unit: Monitoring of the mains voltage Monitoring of the temperature Temperature control via two separate fan circuits Smoke monitoring Vibration monitoring Entry monitoring for the front and rear doors Accessory unit 2U 7200511 Jacks for extension with: UPS DK 7200430 Electromagnetic Ergoform-S front door DK 7200351 Electromagnetic Ergoform-S rear door DK 7200351 Reader units DK 7200380/381/382 Hygro-thermo-sensor DK 7200361 In conjunction with base unit DK 7200100, the following are additionally required: One connection cable 230V, 7200210 (or other country-specific versions) 63

Connection Accessories Power Cable Power is supplied to the CMC base unit via the connection cable. Technical specifications: PVC cable, 3-pin with earthing-pin connector and IEC cable coupler (for non-heating appliances) with CEE22 contact protection. 1 connection cable, length 2.5m Country- Voltage specific versions USA/CDN 115 3686338 D/F/B 230 7200210 Note: Important accessory The connection cable is absolutely necessary for CMC operation. Connector Kit For Connecting Accessories The sensor cables are fastened directly to the respective connector from the connector kit, which is then plugged into the CMC base unit. In this way, the plug connections to the CMC are easily removed and re-installed during maintenance and assembly in the network enclosure. Programming Cable For The RS 232 Interface The RJ 11 jack is connected to the CMC front, the 9-pin Sub-D to a serial PC interface. Packs of 1 set 7200223 Note: Important accessory The connector kit is absolutely necessary for connection of accessory coupling and PC connection. 1 connector kit consisting of: 3 tension spring clamps, 3-pin, 1 tension spring clamp, 10-pin, 1 tension spring clamp, 20-pin, 1 tension spring clamp, 12-pin. Packs of 1 set 7200221 NEW programming cable for the CMC II DK 7200100 Cable For Sensor Connection The 10m long cable can be cut to the exact length required, for optimum connection of sensors, Ergoform-S and access units in the enclosure to the CMC base unit. Technical specifications: LiYY 4 x 0.25mm 2 1 cable, 10m long Required for: Smoke alarm sensor Hygro-thermo sensor Vibration sensor Entry sensor Locking units 24V DC Smart card reader Magnetic card reader Keyboard lock Socket strip Signal lamp Extension bus I 2 C Cable 10m long 9966831 64

Power Supply 24V This power pack is used to supply power to the smoke sensors and the Ergoform-S handle with card or coded lock. For fixing of power pack use cable clamp strap DK 7611000, see below, or module DK 7200400. Input: 100 240V ± 10%, 50/60 Hz /AC Output: 24V DC/0.6 A 1 power pack with top hat rail and fastener for top hat rail, including assembly parts Version Power pack 24V DC 7200240 Required for power supply of: Ergoform-S handle Locking unit 24V DC Smart card reader Magnetic card reader Keyboard lock Smoke alarm sensor Hygro-thermo sensor Signal lamp Extension bus I 2 C Cable Collecting Bar For mounting to the rear of CMC. Cables are fixed by means of cable ties. Narrow version: Only for cables. Wide version: For screened cables with spring terminals, and contacting, as well as fixing of power pack. Material: Sheet steel 2mm, zinc-plated, passivated. Cable clamp strap including assembly parts Version narrow, for cable clamping 7610000 wide, for cable clamping, power pack fixed by 7611000 means of terminal springs Recommended accessory Suppressor For Fans The capacitors eliminate interferences of the fans with self-starting shaded-pole motors. Each fan motor should be provided with a capacitor which is switched in parallel to the net voltage. The capacitors are equipped with terminals so that they are simply connected to the fan cable. Dielectric strength: 275V AC Capacity: 100 nf Type: X2 Version Packs of 100 nf 20 7200490 Following fan systems include self-starting shaded-pole motors: (e.g. SK 3322...., SK 3323...., SK 3324...., SK 3325...., SK 9965912, SK 9965913, SK 9967162, SK 9967163, SK 7980110, DK 7980000 and variants). The fans or the vented roofs can be alternatively equipped with line filters. Line filters available on request. Booster 7 m Reader unit, extension unit DK 7200911 Booster I 2 C-Booster The I 2 C-Booster is used to reinforce the signal of the CMC I 2 C bus system. It can be used optionally. The reader units and extension unit DK 7200911 require 2 boosters. One booster is required for the extension unit DK 7200913. Booster 7 m Extension unit DK 7200913 Pack of 1 7200600* * Extended delivery time. Max. cable length: 7m Further lengths available on request. Rated voltage: 24V DC Rated current: 50mA Interface: I 2 C Operating temperature range: +5 C to +45 C CMC CMC 65

CMC Cable Management Cable Management Module, Mounting Kit For mounting on the 482.6mm (19") section or on the enclosure frame. The module may be fitted at a readily accessible point in the enclosure. Even in fully populated network enclosures, installation work and modifications can still be carried out to perfection. The supplied CMC connection cable gives access to all sensor connections in the module. A top hat rail accommodates terminals or the 24V power pack. The cable may be connected to the sensors using the supplied terminals. Open/ individual wiring is possible. Version Mounting kit 7200400 Width: 482.6mm (19") Height: 1U Depth: 143mm + 12mm Material: Sheet steel, 1mm, passivated Base section, cover plate, terminal blocks, top hat rail, 482.6mm (19") bracket, mounting bracket and CMC connection cable In conjunction with the CMC, the following are additionally required: 1 connection cable DK 7200210 and 1 connector insert DK 7200220 Cable Management Module With Connection System And 24V Power Pack For mounting on the 482.6mm (19") section or on the enclosure frame. The module may be fitted at a readily accessible point in the enclosure. Even in fully populated network enclosures, installation work and retrofitting can still be carried out to perfection. The connection cable attached to the rear with the CMC connector kit is simply connected to the CMC. The front is equipped with 21 RJ 11/12 jacks, 4 terminals and an IEC 320 connection. All sensors are easily connected to the module using RJ 11/12 connectors. The 24V power pack is integrated into the wiring concept. Power for monitoring and for the heater, fan, alarm and power pack is supplied via the IEC 320 connection. Functional description/connection options: RJ 11/12 jacks for CMC accessories: 4 vibration sensors, 7200321 4 entry sensors, 7200331 2 UPS monitoring devices with cable, 7200420 2 smoke sensors, 7200311 2 electromagnetic Ergoform-S, Part No. DK 7200351 Version Wired with sensor jacks 7200411 1 door release with cable, Part No. DK 7200430 2 I 2 C (reader units), 7200380 / 381 / 382 2 temperature sensors, 7200301 2 analog sensors (e.g. hygrothermo-sensors), 7200361 Terminals: 1 alarm (changeover contact for 250V AC, max. 5 A) 1 heater with fuse (normally open contact for 250V AC, max. 5 A) 2 fan systems with fuse (normally open contact for 250V AC, max. 3 A) In conjunction with the CMC, the following are additionally required: 2 connection cables, 7200210 Rated voltage: 24V DC Rated current: 600mA Dimensions: Width: 482.6mm (19"), Height: 1U, Depth: 100mm Temperature range: +5 C to +45 C Accessories Connection Cable RJ 11 / 12 The connection cables are prepared for cable management module. The cable is equipped with an RJ 11/12 connector at one end, while the other end is open for the connection of sensors or actuators. Accessories Extension Cable RJ 11 / 12 The extension cables are prepared for cable management module. The cable is equipped with an RJ 11/12 connector at one end, and an RJ 11/12 jack at the other end. The cables allow easy extension of the Connector P. of RJ 11 4 7200420 RJ 12 4 7200430 The cables facilitate individual wiring with the module. Length 5m Connector/jack P. of RJ 11 4 7200440 RJ 12 4 7200450 connection between the CMC sensors and the module. Length 5m 66

Sensor Accessories Temperature Sensor The economic solution for: Temperature measuring Temperature indication Temperature monitoring Temperature regulation Measuring transformers, one LCD display for indication as well as relays for fan control are made available via the excellent electronic equipment of the CMC. Two NTC sensors for two independent fan circuits/limit control sensors can be connected to one CMC. The temperature sensor, with its preassembled connection cable (2.5m) can be fitted anywhere in the network enclosure. The following are also required for connecting to base unit: Connector kit for connecting accessories, 7200220 If a module DK 7200411 is used, no further accessories are required. Temperature sensor 2.5m connection cable 7200300 2.5m connection cable and RJ 12 jack for 7200301 Type: NTC Resistance: 10 kohm at 25 C Tolerance: ± 1 C Connection lead: LiYY 0.25mm 2 1 temperature sensor incl. 2.5m connection cable, cable support. Max. quantity for 1 CMC: 2 temperature sensors Note: The temperature sensors DK 7200301 can also be used with the CMC extension units. Smoke Alarm Sensor The smoke alarm sensor is an optical smoke alarm consisting of an internal measuring chamber (with infrared LED and photodiode) and an electronic circuit board. If smoke enters the chamber, an LED light pulse is partially deflected by the smoke particles, causing it to strike the photodiode, which in turn triggers further light pulses. If these light pulses strike the photodiode again, smoke generation is signalled to the CMC and an alarm is triggered. The following are also required for connecting to the base unit: Cable for sensor connection, 7200230 Connector kit for connecting accessories, 7200220 Cable clamp strap, 7611000 24V power pack for voltage supply, 7200240 The CMC s power pack is capable of supplying a smoke sensor with 24V. (Note: Observe total capacity). If a module Part No. is used, no further accessories are required. Rated voltage: 17 to 28V DC Closed-circuit current consumption: 30 45 µa at 24V Make current: 90 µa at 24V Rated alarm current: max. 61 ma Temperature range: 20 C to +60 C Dimensions: Ø 100mm, H 50mm Weight: 150 g Smoke alarm sensor without connection cable 7200310 5m connection cable and RJ 12 jack for 7200311 1 smoke alarm sensor including assembly parts. Smoke alarm sensor with VdS-approval no. G293013 100 60 60 69 6.5 4.5 2 100 15 10 25 6.5 7.5 25 25 67

3 If a module is used, no further accessories are required. Hygro-Thermo Sensor The hygro-thermo sensor determines the humidity/temperature and transfers these values into output signals 4...20mA. The sensor is based on 2-wire technology and requires external 24V voltage supply.the CMC monitors the humidity/temperature, indications in [%] 0 100. The CMC has two analog inputs 4 20mA. The following are also required for connecting to the base unit: Cable for sensor connection, 7200230 Connector kit for connecting accessories, 7200220 Cable clamp strap, 7611000 24V power pack for voltage supply, 7200240. The CMC s power pack is capable of supplying a hygro-thermo sensor with 24V. (Note: Observe total capacity) Hygro-thermo sensor w/o connection cable 7200360 5 m connection cable and RJ 12 jacks for 7200361 Rated voltage: 20 28V DC Rated current: 44mA Output signal: 4 20mA corresp. to 0 100% humidity 4 20mA corresp. to 0 50 C Measuring range: 10 90% humidity 0 50 C Operating temperature: 0 C to +50 C Hygro-thermo sensor, mounting bracket, including assembly parts. Vibration Sensor Vibration sensors are suitable for all fixed panels in the network enclosure. If possible, they should be fastened to the center of the side panel or door. If the enclosure is vibrated, the contact inside the sensor closes the circuit and triggers an alarm. The sensitivity of the contact is individually adjustable by means of an adjusting screw which presses onto a leaf spring. The sensor is an economic solution for monitoring vandalism. The high-quality electronic parts of the CMC transfers vibrations of different intensity into a CMC alarm. The following are also required for connecting to the base unit: Cable for sensor connection, 7200230 Packs of 4 w/o connection cable 7200320 5m connection cable and RJ 11 jack for 7200321 Connector kit for connecting accessories, 7200220 If a module DK 7200411 is used, no further accessories are required. Contact rating: max. 50V, 0.1 A Dimensions: W x H x D: 57 x 21 x 18mm 4 vibration sensors including assembly parts. Entry Sensor Entry sensors monitor doors, side panels or windows in the network enclosure. The magnet is secured to the moving part (e.g. side panel), while the reed contact is fastened to the immobile part (enclosure frame). The permanent magnet holds the reed contact in a closed position. If the door is opened or the side panel removed, the reed contact drops out and opens the circuit, leading to an alarm in the CMC. The following are also required for connecting to the base unit: Cable for sensor connection, 7200230 Connector kit for connecting accessories, 7200220 If a module is used, no further accessories as required Packs of 4 w/o connection cable 7200330 5m connection cable and RJ 11 jack for 7200331 Switching voltage: max. 100V DC Max. distance between reed contact and magnet: 5mm 4 entry sensors including assembly parts. 55 40 50 50 10 11.5 6 25 6.5 3.5 3.5 45 Dimensions W x H x D: 55 x 13 x 13mm Switching load: 5 W Switched current: max. 500mA 10 55 25 6 30 3.5 45 15 68

Lock Accessories Important: Consider additional holes and locking rod. Ergoform-S With Electromagnetic Locking The lock unit consists of a Rittal Ergoform-S whose swing lever is electromagnetically locked. With the door closed and the swing lever in position, locking is activated by switching on the lock magnet. For monitoring the door an access sensor is required. The CMC allows the swing lever to be released out by deactivating the lock magnet, so that the door can be opened. Deactivation can be initiated by one of the access units shown below, such as smart card readers, magnetic card readers, coded locks or network management systems. Furthermore the Ergoform-S includes a handle monitoring system with a reed contact. The CMC triggers an alarm signal if the handle is not in position when door is closed. The pushbutton insert supplied can also be exchanged for security inserts. The following are required for connecting to the base unit: Connector kit for connecting accessories, 7200220 24V power pack for voltage supply, 7200240 Bottom locking rod for CMC as per enclosure height (VR enclosures do not require a CMC locking rod). Entry sensor, 7200330 / 331 Additional holes in enclosure door. Cable clamp strap 7611000 If a module Part No. is used, no further accessories are required. Color: RAL 7035 (light grey) Rated voltage: 24V DC Rated current: max. 100mA Design 4m connection cable 7200350 5m connection cable and RJ 12 jack for 7200351 1 Ergoform-S handle, 1 pushbutton insert, 1 connection cable, electromagnetic lock unit, assembly parts. 50 50 87 42 42 79.2 ± 0.1 4 Security insert Design Part No. SZ Security insert 2467000 Lock no. 3524 E Security pushbutton insert 2469000 Lock no. 2123 E Locking rods Design Bottom CMC locking rod for 2000mm high 7200371 PS enclosures Further information available on request. 8 4.2 18 ± 0.1 6 Ergoform-S With Electromagnetic Locking For QuickRack The electromagnetic Ergoform-S handle for QuickRack is identical to Ergoform-S DK 7200350 (for description see above). The following are required for connecting to the base unit: Connector kit for connecting accessories, 7200220 24V power pack for voltage supply, 7200240 Additional holes in enclosure door (drawing see above) Design 4 m connection cable 7200650* * Extended delivery time. Cable clamp strap, 7611000 Access sensor, 7200330 Rated voltage: 24V DC Rated current: max. 100mA 69

Smart Card Reader 3 smart cards with I 2 C chip (E-Eprom) are supplied with the smart card reader. Each card contains a four-digit code, which is different on all three cards. All cards are access-authorized (adjustable in the CMC). The four-digit code is transmitted to the CMC and, if applicable, to the network management system, via the I 2 C bus. Technical specifications: Type: Manual insertion reader Card type: Smart cards with I 2 C chip Supply voltage: 24V DC Power consumption: 150mA Interface: I 2 C bus 1 smart card reader, 3 smart cards Assembly parts, adaptor for PS glazed door 190 w/o connection cable 7200340 3m connection cable and RJ 12 jack for 7200380 50 190 165 83 50 8.5 4 25 120 Magnetic Card Reader 3 magnetic cards are supplied with the magnetic card reader. Each card contains a four-digit code, which is different on all three cards. All cards are access-authorized (adjustable in the CMC). The four-digit code is transmitted to the CMC, and if applicable to the network management system, via the I 2 C bus. Technical specifications: Type: Manual insertion reader Card type: Magnetic strip card with information on track 2 Supply voltage: 24V DC Power consumption: 150mA Interface: I 2 C bus 1 magnetic card reader, 3 magnetic cards assembly parts, adaptor for PS glazed door 190 w/o connection cable 7200341 3m connection cable and RJ 12 jack for 7200381 50 190 165 83 50 8.5 4 120 35 Keyboard Lock Four-digit numbers may be entered in the CMC. The authorized codes can be adjusted with the CMC via RS 232 or Telnet. The entered code is transmitted to the CMC and, if applicable, to the network management system, via the I 2 C bus. Type: Keypad Rated voltage: 24V DC Rated current: max. 150mA Interface: I 2 C bus 1 coded lock assembly parts, adaptor for PS glazed door 190 w/o connection cable 7200342 3m connection cable and RJ 12 jack for 7200382 50 190 165 25 83 50 8.5 4 120 70