3M Purification Inc. 3M Air Management Products for Your Commercial HVAC Needs. Create. Air. Confidence

3M Purification Inc. 3M Air Management s for Your Commercial HVAC Needs Create an Air of Confidence

Pursuing Innovation 3M Company has long encouraged employees to pursue ideas and concepts that might, at first, seem unusual or odd to some people. From those efforts, many innovations were born. In the late 1930s, one of 3M s scientists Al Boese began a journey to develop an inexpensive, noncorrosive backing that was fibrous, but not woven, for electrical tape. The journey took him through a decade of learning and experimentation that did not produce a better backing for electrical tape, but did lead to an amazing series of products using the new technology. Al Boese retired in the 1980s, however, the journey he started continues today: 3M is still finding new ways to refine and apply the nonwoven materials. Making the Connection One of the most successful uses of the 3M non-woven technology is the 3M personal respirator. The challenge for the product design is to protect individuals, while also allowing maximum comfort and breathability. The innovation required to do this was years of R&D research, resulting in a fundamental base for 3M HVAC air filters. It was the same principle, stop unwanted particles but maximizing airflow. Breathable Filtration Today, 3M is arguably considered the world s leading expert on breathable synthetic-based filtration products. For 3M HVAC air filters, this means filtration with best in class pressure drops and lightweight media, analogous to the design criteria for personal respirators. Technological Innovation Journey 1940s 1950s 1960s 1970s 1980s 1990s 2000s 2010s First 3M Nonwoven s Introduced Meltblown Webs Personal Respirators Surgical Masks Furnace Filters Cabin Air Filters First HVAC Mini-pleated Filters HVAC V-Bank Filters

Our Story Building managers and HVAC engineers often face a fine balance of finding the best air filter solution for the building and keeping their operating budgets in check. Meeting environmental requirements for buildings is becoming increasingly important too. Energy consumption related to HVAC systems is a significant component of the overall energy consumption required to operate a building. Using energy efficient air handlers is one step towards reducing those operational costs. Choosing the right HVAC replacement filters helps maximize those savings opportunities. The greater the ability of a filter to load with debris without substantial increase in pressure drop, the greater the possible energy savings. HVAC engineers typically look for filters that have a low initial pressure drop, high filter loading capacity and the minimum required particle capture efficiency required. Filtration requirements, time constraints, energy, and sustainability efforts create a number of decisions that have to be researched and analyzed. Using HVAC filter and air handling unit performance data, 3M can help managers look for opportunities for improvement in associated Total Cost of Ownership (TCO). Focusing on opportunities to lower energy consumption, reduce filter maintenance time and reduce waste stream volume, have provided favorable results. Total Cost of Ownership There are five components of the ownership and operating cost of HVAC filters: the cost to purchase the filters, the cost of the associated energy use, the cost of labor for installation and replacement, the cost of disposal, and the cost of shipping. Using 3M Commercial HVAC Filters may have a positive impact on the ownership and operating cost as a result of their low pressure drop and their design for long filter life. The Total Cost of Ownership tool from 3M, for commercial HVAC air filtration systems, can be utilized to compare 3M Commercial HVAC Filters with alternative filter options. 3M offers complimentary filter evaluation services to help in your decision-making.

V-Bank Filters MERV A15 MERV A14 MERV A13 Industry leading low pressure drop Long filter life Factory installed gaskets for consistent reduction of air bypass Lightweight frame construction for easy handling and installation 3M Commercial HVAC V-Bank Filters MERV A13, MERV A14 and MERV A15 offer a unique combination of performance and design features including integral gaskets and nested pleat packs. These filters are an excellent choice for building owners and facility managers looking to reduce their energy utilization and minimize their total cost of operation, while still providing building occupants with high quality filtered air. Using 3M technologies, these commercial HVAC filters offer an industry leading combination of low pressure drop, robust efficiency, longevity, low weight as well as unique design features. These design features include nested pleats for reduced pressure drop and highly engineered media with a precise balance of mechanical and electret characteristics. The robust efficiency of these filters is tested to the rigorous industry filter conditioning standard ASHRAE 52.2: 2007 Appendix J. 3M V-Bank Filters are the only HVAC V-Bank filters that feature innovative integral gaskets. No other manufacturer offers this feature, which helps prevent unfiltered air from flowing past gaps between the filter and the filter rack. The integral gaskets from 3M are factory installed, which not only save time during installation, but ensure that gaskets will be used. Integral gaskets reduce air bypass, keeping coils clean Nested pleats for reduced pressure drop Innovative, open filtration media structure Key benefits Potential for reduction in electrical energy consumption due to industry leading low initial pressure drop. Filters with MERV 13 and greater ratings contribute to earning a point in the LEED certification process for new and existing buildings when used on all outside air intakes and inside air recirculation returns. Filters with MERV A13 and A14 ratings meet the Facilities Guidelines Institutes (ANSI / ASHRAE / ASHE Standard 170-2013) requirements for hospitals and healthcare facilities where MERV 13 or 14 primary filters are required. Long filter life, due to the unique combination of electret, depth-loading filtration media, the precision pleat structure and high filter media area. Factory installed gaskets ensure correct installation and usage, resulting in consistent reduction of air bypass, as well as eliminating the need for additional labor to install gaskets on-site. Due to their lightweight frame construction, 3M V-Bank Filters are easier to handle, transport, and install than many comparable V-Bank filters and metal box filters. Lighter weight is especially important when HVAC filters must be manually carried to the air handler. 3M V-Bank Filters are 100% synthetic, resulting in moisture and humidity resistant, corrosion free filters that do not support mold growth. 3M V-Bank Filters are 100% metal free and fully incinerable. 3M V-Bank Filters meet UL 900 flammability rating (US) and UL 900 Class 2 flammability rating (Canada). Reverse Flow options are also available.

MERV A15 MERV A15 Performance Data 492 fpm (1968 cfm for 24 x 24 filter) Initial pressure drop 0.26 w.g. Recommended final pressure drop 1.5 w.g. Efficiency Rating per ASHRAE 52.2: 2007 MERV 16 1 Efficiency Rating per ASHRAE 52.2: 2007 Appendix J MERV A15 Dust Holding Capacity at 1.5 w.g. 215 g Initial Resistance vs Air Velocity Minimum Filter Efficiency vs. Particle Size at 492 fpm Resistance (inches of water). 0.6 0.5 0.4 0.3 0.2 0.1 Initial Filter Resistance 0.0 0 100 200 300 400 500 600 700 800 Flow Rate (fpm) KCl Efficiency (%) Filter Efficiency vs. Particle Size at 492 fpm per ASHRAE 100 90 80 70 60 50 40 30 20 10 Appendix J 0 0 1 2 3 4 5 6 7 8 9 10 Particle Size (microns) Average Initial Pressure Drop is 0.26 inches of water @ 492 fpm MERV A14 MERV A14 Performance Data 492 fpm (1968 cfm for 24 x 24 filter) Initial pressure drop 0.23 w.g. Recommended final pressure drop 1.5 w.g. Efficiency Rating per ASHRAE 52.2: 2007 MERV 15 1 Efficiency Rating per ASHRAE 52.2: 2007 Appendix J MERV A14 Dust Holding Capacity at 1.5 w.g. 235 g Initial Resistance vs Air Velocity Minimum Filter Efficiency vs. Particle Size at 492 fpm Resistance (inches of water). 0.5 0.4 0.3 0.2 0.1 Initial Filter Resistance 0.0 0 100 200 300 400 500 600 700 800 Flow Rate (fpm) KCl Efficiency (%) Filter Efficiency vs. Particle Size at 492 fpm per ASHRAE 100 90 80 70 60 50 40 30 20 Appendix J 10 0 0 1 2 3 4 5 6 7 8 9 10 Particle Size (microns) Average Initial Pressure Drop is 0.23 inches of water @ 492 fpm

MERV A13 MERV A13 Performance Data Initial pressure drop Recommended final pressure drop 492 fpm (1968 cfm for 24 x 24 filter) 0.21 w.g. 1.5 w.g. Efficiency Rating per ASHRAE 52.2: 2007 MERV 14 1 Efficiency Rating per ASHRAE 52.2: 2007 Appendix J Dust Holding Capacity at 1.5 w.g. MERV A13 225 g Important use restriction: This filter must not be used as a primary filter in hospitals and healthcare facilities where a MERV 14 primary filter is required per ASHRAE 170-2013. 3M recommends the use of 3M Commercial HVAC Filter s with a minimum rating of MERV A14. Resistance (inches of water). Initial Resistance vs Air Velocity Minimum Filter Efficiency vs. Particle Size at 492 fpm Initial Filter Resistance 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 0 100 200 300 400 500 600 700 800 Flow Rate (fpm) Average Initial Pressure Drop is 0.21 inches of water @ 492 fpm KCl Efficiency (%) Filter Efficiency vs. Particle Size at 492 fpm per ASHRAE 100 90 80 70 60 50 40 30 20 Appendix J 10 0 0 1 2 3 4 5 6 7 8 9 10 Particle Size (microns) B Filter Measurements A C MERV A15 (MERV 16 Efficiency Rating per ASHRAE 52.2-2007) Standard Flow Reverse Flow Nominal Dimensions "A" x "B" x "C" Width "A" Width "B" Width "C" E739 70-0714-7184-4 E760 70-0714-7206-5 24 x 24 x 12 (610 x 610 x 305) 23 3/8 (594) 23 3/8 (594) 11.9 (302) E740 70-0714-7185-1 E763 70-0714-7209-9 20 x 24 x 12 (508 x 610 x 305) 23 3/8 (594) 19 3/8 (492) 11.9 (302) E741 70-0714-7186-9 E766 70-0714-7212-3 12 x 24 x 12 (305 x 610 x 305) 23 3/8 (594) 11 3/8 (289) 11.9 (302) MERV A14 (MERV 15 Efficiency Rating per ASHRAE 52.2-2007) Standard Flow Reverse Flow Nominal Dimensions "A" x "B" x "C" Width "A" Width "B" Width "C" E733 70-0714-7178-6 E759 70-0714-7205-7 24 x 24 x 12 (610 x 610 x 305) 23 3/8 (594) 23 3/8 (594) 11.9 (302) E734 70-0714-7179-4 E762 70-0714-7208-1 20 x 24 x 12 (508 x 610 x 305) 23 3/8 (594) 19 3/8 (492) 11.9 (302) E735 70-0714-7180-2 E765 70-0714-7211-5 12 x 24 x 12 (305 x 610 x 305) 23 3/8 (594) 11 3/8 (289) 11.9 (302) MERV A13 (MERV 14 Efficiency Rating per ASHRAE 52.2-2007) Standard Flow Reverse Flow Nominal Dimensions "A" x "B" x "C" Width "A" Width "B" Width "C" E736 70-0714-7181-0 E758 70-0714-7204-0 24 x 24 x 12 (610 x 610 x 305) 23 3/8 (594) 23 3/8 (594) 11.9 (302) E737 70-0714-7182-8 E761 70-0714-7207-3 20 x 24 x 12 (508 x 610 x 305) 23 3/8 (594) 19 3/8 (492) 11.9 (302) E738 70-0714-7183-6 E764 70-0714-7210-7 12 x 24 x 12 (305 x 610 x 305) 23 3/8 (594) 11 3/8 (289) 11.9 (302)

Mini-pleat Filters with Gasket 3M Mini-Pleat Filters with Gasket combine effective filtration performance with low airflow resistance and long filter life, which can lead to lower energy consumption as well as reduced waste disposal volume and labor cost. Our customers value the filters properties that lead to time and money savings and help them keep their operating and maintenance budgets in line. Low pressure drop for potential energy savings Long filter life Factory installed gaskets for consistent reduction of air bypass Simple, hassle-free installation without clips Integral gaskets prevent air bypass, keeping coils clean Glue beads maintain pleat spacing integrity Key benefits Significant energy savings possible when installed in place of standard filters due to low pressure drop achieved through the use of our highly refined electrostatically charged media (electret media), open filtration media structure and high surface area mini-pleat design. Longer filter life than competitive products due to the unique combination of depth loading filtration media, precise pleat structure and high filter media area. Mini-Pleat Filters with Gasket allow for simple upgrade of in-place filters, without additional capital expenditures. Minimized air bypass around and between filters, common in damaged or misaligned air handling racks, due to innovative filter frame with integrated gaskets. Reduced labor hours due to simple, hassle-free installation, supported by the innovative slip-rib frame design due to longer filter life which results in fewer filter change-outs factory installed integral gaskets, which eliminate labor required to install and properly align gaskets on site as no clips are required when installing 3M Mini-Pleat with gasket filters Far less storage space required compared to many filters of same efficiency resulting from the high performance 2 mini-pleat filter format. Significant energy value and low ash content resulting from 100% incinerable components of the filter and resistant to moisture and common chemicals. Tough filter construction resulting in low chance of filter damage during handling, installation and resistant to moisture amd common chemicals. Reliable performance in the most extreme commercial office building HVAC environments due to durable, moisture and humidity resistant, 100% synthetic filtration media, 100% metal free filter design and engineered frame construction. Superior product quality with consistent performance via rigorous ISO 9001 2008 certified manufacturing process, a full on-site HVAC laboratory testing facility and field testing capability. Available in MERV A8, MERV A11, MERV A12 and MERV A13, 3M Mini-Pleat Filters with Gasket are an excellent choice as either primary or as pre-filters in a variety of applications. The 3M Commercial HVAC Filter MERV A8, MERV A11 and MERV A12 contribute to earning a point in the LEED certification process during the construction phase for new buildings and renovations. The 3M Commercial HVAC Filter MERV A13 Mini-Pleat with Gasket contributes to earning a point in the LEED certification process for existing and new buildings by using the filter on all outside air intakes and inside air recirculation returns. No clips are required when installing

MERV A13 Contributes to earning one point towards LEED certification process MERV A13 Performance Data 492 fpm (1968 cfm for 24" x 24" filter) Initial Pressure Drop 0.39" w.g. Recommended Final Pressure Drop 1.4" w.g. Efficiency Rating per ASHRAE 52.2: 2007 MERV 14¹ Efficiency Rating per ASHRAE 52.2: 2007 Appendix J MERV A13 Dust Holding Capacity at 1.4" w.g. 95 ± 7 g I KCl Efficiency (%) 100 90 80 70 60 50 40 30 20 10 Filter Measurements A Minimum Filter Efficiency vs. Particle Size at 492 fpm 0 0 1 2 3 4 5 6 7 8 9 10 Particle Size (microns) B C Appendix J Initial Resistance (inches of water) 0.60 0.50 0.40 0.30 0.20 0.10 Initial Pressure Drop vs. Air Velocity 24" x 24" Filter 0.00 0 100 200 300 400 500 fpm Nominal Dimensions A x B x C Average Initial Pressure Drop is 0.39 w.g. Width A Height B Depth C E675 70-0714-7119-0 10 x 10 x 2 (254 x 254 x 51) 9 3/8 (238) 9 3/8 (238) 1 7/8 (48) E676 70-0714-7120-8 10 x 20 x 2 (254 x 508 x 51) 9 3/8 (238) 19 3/8 (492) 1 7/8 (48) E677 70-0714-7121-6 12 x 20 x 2 (305 x 508 x 51) 11 3/8 (289) 19 3/8 (492) 1 7/8 (48) E678 70-0714-7122-4 12 x 24 x 2 (305 x 610 x 51) 11 3/8 (289) 23 3/8 (594) 1 7/8 (48) E679 70-0714-7123-2 14 x 20 x 2 (356 x 508 x 51) 13 3/8 (340) 19 3/8 (492) 1 7/8 (48) E680 70-0714-7124-0 14 x 25 x 2 (356 x 635 x 51) 13 3/8 (340) 24 3/8 (619) 1 7/8 (48) E681 70-0714-7125-7 15 x 20 x 2 (381 x 508 x 51) 14 3/8 (365) 19 3/8 (492) 1 7/8 (48) E682 70-0714-7126-5 16 x 16 x 2 (406 x 406 x 51) 15 3/8 (391) 15 3/8 (391) 1 7/8 (48) E683 70-0714-7127-3 16 x 20 x 2 (406 x 508 x 51) 15 3/8 (391) 19 3/8 (492) 1 7/8 (48) E684 70-0714-7128-1 16 x 24 x 2 (406 x 610 x 51) 15 3/8 (391) 23 3/8 (594) 1 7/8 (48) E685 70-0714-7129-9 16 x 25 x 2 (406 x 635 x 51) 15 3/8 (391) 24 3/8 (619) 1 7/8 (48) E686 70-0714-7130-7 18 x 20 x 2 (457 x 508 x 51) 17 3/8 (441) 19 3/8 (492) 1 7/8 (48) E687 70-0714-7131-5 18 x 24 x 2 (457 x 610 x 51) 17 3/8 (441) 23 3/8 (594) 1 7/8 (48) E688 70-0714-7132-3 18 x 25 x 2 (457 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E689 70-0714-7133-1 20 x 20 x 2 (508 x 508 x 51) 19 3/8 (492) 19 3/8 (492) 1 7/8 (48) E690 70-0714-7134-9 20 x 24 x 2 (508 x 610 x 51) 19 3/8 (492) 23 3/8 (594) 1 7/8 (48) E691 70-0714-7135-6 20 x 25 x 2 (508 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E694 70-0714-7138-0 20 x 30 x 2 (508 x 762 x 51) 19 3/8 (492) 29 3/8 (746) 1 7/8 (48) E692 70-0714-7136-4 24 x 24 x 2 (610 x 610 x 51) 23 3/8 (594) 23 3/8 (594) 1 7/8 (48) E693 70-0714-7137-2 25 x 25 x 2 (635 x 635 x 51) 24 3/8 (619) 24 3/8 (619) 1 7/8 (48) 1 The particle capture efficiency will reduce in actual use. Please visit www.whatismerva.com for more information.

MERV A12 MERV A12 Performance Data 492 fpm (1968 cfm for 24" x 24" filter) Initial Pressure Drop 0.37" w.g. Recommended Final Pressure Drop 1.4" w.g. Efficiency Rating per ASHRAE 52.2: 2007 MERV 14¹ Efficiency Rating per ASHRAE 52.2: 2007 Appendix J MERV A12 Dust Holding Capacity at 1.4" w.g. 93 ± 21 g KCl Efficiency (%) 100 90 80 70 60 50 40 30 Minimum Filter Efficiency vs. Particle Size at 492 fpm Per ASHRAE 52.2-2007 Per ASHRAE-2007 Appendix J 0 1 2 3 4 5 6 7 8 9 Particle Size (microns) Initial Pressure Drop (inches of water) 0.60 0.50 0.40 0.30 0.20 0.10 Initial Pressure Drop vs. Air Velocity 24" x 24" Filter 0.00 100 200 300 400 500 600 700 fpm Average Initial Pressure Drop is 0.37 w.g. Filter Measurements A B C Nominal Dimensions A x B x C Width A Height B Depth C E133 70-0708-1943-1 10 x 10 x 2 (254 x 254 x 51) 9 3/8 (238) 9 3/8 (238) 1 7/8 (48) E124 70-0708-1934-0 10 x 20 x 2 (254 x 508 x 51) 9 3/8 (238) 19 3/8 (492) 1 7/8 (48) E125 70-0708-1935-7 12 x 20 x 2 (305 x 508 x 51) 11 3/8 (289) 19 3/8 (492) 1 7/8 (48) F978 70-0708-1806-0 12 x 24 x 2 (305 x 610 x 51) 11 3/8 (289) 23 3/8 (594) 1 7/8 (48) E126 70-0708-1936-5 14 x 20 x 2 (356 x 508 x 51) 13 3/8 (340) 19 3/8 (492) 1 7/8 (48) E127 70-0708-1937-3 14 x 25 x 2 (356 x 635 x 51) 13 3/8 (340) 24 3/8 (619) 1 7/8 (48) E136 70-0708-1946-4 15 x 20 x 2 (381 x 508 x 51) 14 3/8 (365) 19 3/8 (492) 1 7/8 (48) E128 70-0708-1938-1 16 x 16 x 2 (406 x 406 x 51) 15 3/8 (391) 15 3/8 (391) 1 7/8 (48) F979 70-0708-1807-8 16 x 20 x 2 (406 x 508 x 51) 15 3/8 (391) 19 3/8 (492) 1 7/8 (48) E129 70-0708-1939-9 16 x 24 x 2 (406 x 610 x 51) 15 3/8 (391) 23 3/8 (594) 1 7/8 (48) F980 70-0708-1808-6 16 x 25 x 2 (406 x 635 x 51) 15 3/8 (391) 24 3/8 (619) 1 7/8 (48) E132 70-0708-1942-3 18 x 20 x 2 (457 x 508 x 51) 17 3/8 (441) 19 3/8 (492) 1 7/8 (48) F981 70-0708-1890-4 18 x 24 x 2 (457 x 610 x 51) 17 3/8 (441) 23 3/8 (594) 1 7/8 (48) E130 70-0708-1940-7 18 x 25 x 2 (457 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) F977 70-0708-1805-2 20 x 20 x 2 (508 x 508 x 51) 19 3/8 (492) 19 3/8 (492) 1 7/8 (48) E131 70-0708-1941-5 20 x 24 x 2 (508 x 610 x 51) 19 3/8 (492) 23 3/8 (594) 1 7/8 (48) F982 70-0708-1810-2 20 x 25 x 2 (508 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E134 70-0708-1944-9 20 x 30 x 2 (508 x 762 x 51) 19 3/8 (492) 29 3/8 (746) 1 7/8 (48) F976 70-0708-1804-5 24 x 24 x 2 (610 x 610 x 51) 23 3/8 (594) 23 3/8 (594) 1 7/8 (48) E135 70-0708-1945-6 25 x 25 x 2 (635 x 635 x 51) 24 3/8 (619) 24 3/8 (619) 1 7/8 (48)

1 MERV A11 MERV A11 Performance Data 492 fpm (1968 cfm for 24" x 24" filter) Initial Pressure Drop 0.25" w.g. Recommended Final Pressure Drop 1.4" w.g. Efficiency Rating per ASHRAE 52.2: 2007 MERV 12¹ Efficiency Rating per ASHRAE 52.2: 2007 Appendix J MERV A11 Dust Holding Capacity at 1.4" w.g. 110 ± 17 g KCl Efficiency (%) 100 90 80 70 60 50 40 30 20 Minimum Filter Efficiency vs. Particle Size at 492 fpm Appendix J 0 1 2 3 4 5 6 7 8 9 Particle Size (microns) Initial Pressure Drop (inches of water) 0.3 0.2 0.1 Initial Pressure Drop vs. Air Velocity 24" x 24" Filter 0.0 0 100 200 300 400 500 Flow Rate (fpm) Average Initial Pressure Drop is 0.25 inches w.g. Filter Measurements A B C Nominal Dimensions A x B x C Width A Height B Depth C E695 70-0714-7139-8 10 x 10 x 2 (254 x 254 x 51) 9 3/8 (238) 9 3/8 (238) 1 7/8 (48) E696 70-0714-7140-6 10 x 20 x 2 (254 x 508 x 51) 9 3/8 (238) 19 3/8 (492) 1 7/8 (48) E697 70-0714-7141-4 12 x 20 x 2 (305 x 508 x 51) 11 3/8 (289) 19 3/8 (492) 1 7/8 (48) E698 70-0714-7142-2 12 x 24 x 2 (305 x 610 x 51) 11 3/8 (289) 23 3/8 (594) 1 7/8 (48) E699 70-0714-7143-0 14 x 20 x 2 (356 x 508 x 51) 13 3/8 (340) 19 3/8 (492) 1 7/8 (48) E700 70-0714-7144-8 14 x 25 x 2 (356 x 635 x 51) 13 3/8 (340) 24 3/8 (619) 1 7/8 (48) E701 70-0714-7145-5 15 x 20 x 2 (381 x 508 x 51) 14 3/8 (365) 19 3/8 (492) 1 7/8 (48) E702 70-0714-7146-3 16 x 16 x 2 (406 x 406 x 51) 15 3/8 (391) 15 3/8 (391) 1 7/8 (48) E703 70-0714-7147-1 16 x 20 x 2 (406 x 508 x 51) 15 3/8 (391) 19 3/8 (492) 1 7/8 (48) E704 70-0714-7148-9 16 x 24 x 2 (406 x 610 x 51) 15 3/8 (391) 23 3/8 (594) 1 7/8 (48) E705 70-0714-7149-7 16 x 25 x 2 (406 x 635 x 51) 15 3/8 (391) 24 3/8 (619) 1 7/8 (48) E706 70-0714-7150-5 18 x 20 x 2 (457 x 508 x 51) 17 3/8 (441) 19 3/8 (492) 1 7/8 (48) E707 70-0714-7151-3 18 x 24 x 2 (457 x 610 x 51) 17 3/8 (441) 23 3/8 (594) 1 7/8 (48) E708 70-0714-7152-1 18 x 25 x 2 (457 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E709 70-0714-7153-9 20 x 20 x 2 (508 x 508 x 51) 19 3/8 (492) 19 3/8 (492) 1 7/8 (48) E710 70-0714-7154-7 20 x 24 x 2 (508 x 610 x 51) 19 3/8 (492) 23 3/8 (594) 1 7/8 (48) E711 70-0714-7155-4 20 x 25 x 2 (508 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E714 70-0714-7158-8 20 x 30 x 2 (508 x 762 x 51) 19 3/8 (492) 29 3/8 (746) 1 7/8 (48) E712 70-0714-7156-2 24 x 24 x 2 (610 x 610 x 51) 23 3/8 (594) 23 3/8 (594) 1 7/8 (48) E713 70-0714-7157-0 25 x 25 x 2 (635 x 635 x 51) 24 3/8 (619) 24 3/8 (619) 1 7/8 (48) The particle capture efficiency will reduce in actual use. Please visit www.whatismerva.com for more information.

MERV A8 MERV A8 Performance Data 492 fpm (1968 cfm for 24" x 24" filter) Initial Pressure Drop 0.26" w.g. Recommended Final Pressure Drop 1.4" w.g. Efficiency Rating per ASHRAE 52.2: 2007 MERV 11¹ Efficiency Rating per ASHRAE 52.2: 2007 Appendix J MERV A8 Dust Holding Capacity at 1.4" w.g. 90 ± 15 g KCl Efficiency (%) Filter Measurements A Minimum Filter Efficiency vs. Particle Size at 492 fpm 100 0.40 90 80 0.30 70 60 0.20 50 40 Appendix J 0.10 30 20 0 1 2 3 4 5 6 7 8 9 0.00 100 200 300 400 500 600 700 Particle Size (microns) fpm Average Initial Pressure Drop is 0.26 w.g. B C Initial Pressure Drop (inches of water) Nominal Dimensions A x B x C Initial Pressure Drop vs. Air Velocity 24" x 24" Filter Width A Height B Depth C E276 70-0712-4438-1 10 x 10 x 2 (254 x 254 x 51) 9 3/8 (238) 9 3/8 (238) 1 7/8 (48) E277 70-0712-4439-9 10 x 20 x 2 (254 x 508 x 51) 9 3/8 (238) 19 3/8 (492) 1 7/8 (48) E278 70-0712-4440-7 12 x 20 x 2 (305 x 508 x 51) 11 3/8 (289) 19 3/8 (492) 1 7/8 (48) E279 70-0712-4441-5 12 x 24 x 2 (305 x 610 x 51) 11 3/8 (289) 23 3/8 (594) 1 7/8 (48) E280 70-0712-4442-3 14 x 20 x 2 (356 x 508 x 51) 13 3/8 (340) 19 3/8 (492) 1 7/8 (48) E281 70-0712-4443-1 14 x 25 x 2 (356 x 635 x 51) 13 3/8 (340) 24 3/8 (619) 1 7/8 (48) E282 70-0712-4444-9 15 x 20 x 2 (381 x 508 x 51) 14 3/8 (365) 19 3/8 (492) 1 7/8 (48) E283 70-0712-4445-6 16 x 16 x 2 (406 x 406 x 51) 15 3/8 (391) 15 3/8 (391) 1 7/8 (48) E284 70-0712-4446-4 16 x 20 x 2 (406 x 508 x 51) 15 3/8 (391) 19 3/8 (492) 1 7/8 (48) E285 70-0712-4447-2 16 x 24 x 2 (406 x 610 x 51) 15 3/8 (391) 23 3/8 (594) 1 7/8 (48) E286 70-0712-4448-0 16 x 25 x 2 (406 x 635 x 51) 15 3/8 (391) 24 3/8 (619) 1 7/8 (48) E287 70-0712-4449-8 18 x 20 x 2 (457 x 508 x 51) 17 3/8 (441) 19 3/8 (492) 1 7/8 (48) E288 70-0712-4450-6 18 x 24 x 2 (457 x 610 x 51) 17 3/8 (441) 23 3/8 (594) 1 7/8 (48) E289 70-0712-4451-4 18 x 25 x 2 (457 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E290 70-0712-4452-2 20 x 20 x 2 (508 x 508 x 51) 19 3/8 (492) 19 3/8 (492) 1 7/8 (48) E291 70-0712-4453-0 20 x 24 x 2 (508 x 610 x 51) 19 3/8 (492) 23 3/8 (594) 1 7/8 (48) E292 70-0712-4454-8 20 x 25 x 2 (508 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E293 70-0712-4455-5 20 x 30 x 2 (508 x 762 x 51) 19 3/8 (492) 29 3/8 (746) 1 7/8 (48) E294 70-0712-4456-3 24 x 24 x 2 (610 x 610 x 51) 23 3/8 (594) 23 3/8 (594) 1 7/8 (48) E295 70-0712-4457-1 25 x 25 x 2 (635 x 635 x 51) 24 3/8 (619) 24 3/8 (619) 1 7/8 (48)

Mini-Pleat Filters, No Gasket 3M Commercial HVAC Filter MERV A8 and A12 Mini-Pleat Filters without Gaskets combine excellent filtration performance with low airflow resistance and long filter life in a cost effective construction. Their balance of properties may offer building owners and managers time and money savings. Low pressure drop for potential energy savings Long filter life Tough filter and frame construction resulting in low chance of filter damage during handling, installation or use in humid environments Key benefits Increased air flow or lower fan energy consumption compared to equivalent filter design and efficiency of competitors Electrostatically charged, open construction media Durable synthetic media and frame construction Long filter life Media loads through the depth of the filter Mini-pleat construction provides high surface area Small Package Size Easy to handle, low disposal volume, low shipping costs Demonstrated filtration efficiency Lightweight, rigid frame 100% Synthetic media-filters are very durable: Less chance of filter damage during handling and installation Resistant to moisture and common chemicals Resistant to fiber shedding

MERV A12 Initial Resistance (inches of water) 0.60 0.50 0.40 0.30 0.20 0.10 Initial Resistance vs. Air Velocity MERV A12 Performance Data Initial Resistance 0.00 0 100 200 300 400 500 600 700 Flow Rate (fpm) Recommended Final Resistance Efficiency Rating per ASHRAE 52.2: 2007 MERV 14 1 Efficiency Rating per ASHRAE 52.2: 2007 Appendix J 492 fpm (1968 cfm for 24 x 24 filter) 0.37 inches of water 1.4 inches of water MERV A12 Average Dust Holding Capacity at 1.4 inches of water 93±21g Resistance (inches of water) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 Resistance vs. Dust Loading @ 492 fpm 0 10 20 30 40 50 60 70 80 ASHRAE Dust Fed (g) Filter Measurements A B C Stock Nominal Dimensions Width A Height B Depth C E358 70-0712-4567-7 10 x 10 x 2 (254 x 254 x 51) 9 3/8 (238) 9 3/8 (238) 1 7/8 (48) E359 70-0712-4568-5 10 x 20 x 2 (254 x 508 x 51) 9 3/8 (238) 19 3/8 (492) 1 7/8 (48) E360 70-0712-4569-3 12 x 20 x 2 (305 x 508 x 51) 11 3/8 (289) 19 3/8 (492) 1 7/8 (48) E361 70-0712-4570-1 12 x 24 x 2 (305 x 610 x 51) 11 3/8 (289) 23 3/8 (594) 1 7/8 (48) E362 70-0712-4571-9 14 x 20 x 2 (356 x 508 x 51) 13 3/8 (340) 19 3/8 (492) 1 7/8 (48) E363 70-0712-4572-7 14 x 25 x 2 (356 x 635 x 51) 13 3/8 (340) 24 3/8 (619) 1 7/8 (48) E364 70-0712-4573-5 15 x 20 x 2 (381 x 508 x 51) 14 3/8 (365) 19 3/8 (492) 1 7/8 (48) E365 70-0712-4574-3 16 x 16 x 2 (406 x 406 x 51) 15 3/8 (391) 15 3/8 (391) 1 7/8 (48) E366 70-0712-4575-0 16 x 20 x 2 (406 x 508 x 51) 15 3/8 (391) 19 3/8 (492) 1 7/8 (48) E367 70-0712-4576-8 16 x 24 x 2 (406 x 610 x 51) 15 3/8 (391) 23 3/8 (594) 1 7/8 (48) E368 70-0712-4577-6 16 x 25 x 2 (406 x 635 x 51) 15 3/8 (391) 24 3/8 (619) 1 7/8 (48) E369 70-0712-4578-4 18 x 20 x 2 (457 x 508 x 51) 17 3/8 (441) 19 3/8 (492) 1 7/8 (48) E370 70-0712-4579-2 18 x 24 x 2 (457 x 610 x 51) 17 3/8 (441) 23 3/8 (594) 1 7/8 (48) E371 70-0712-4580-0 18 x 25 x 2 (457 x 634 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E372 70-0712-4581-8 20 x 20 x 2 (508 x 508 x 51) 19 3/8 (492) 19 3/8 (492) 1 7/8 (48) E373 70-0712-4582-6 20 x 24 x 2 (508 x 610 x 51) 19 3/8 (492) 23 3/8 (594) 1 7/8 (48) E374 70-0712-4583-4 20 x 25 x 2 (508 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E375 70-0712-4584-2 20 x 30 x 2 (508 x 762 x 51) 19 3/8 (492) 29 3/8 (746) 1 7/8 (48) E376 70-0712-4585-9 24 x 24 x 2 (610 x 610 x 51) 23 3/8 (594) 23 3/8 (594) 1 7/8 (48) E377 70-0712-4586-7 25 x 25 x 2 (635 x 635 x 51) 24 3/8 (619) 24 3/8 (619) 1 7/8 (48)

MERV A8 Resistance (inches of water) 0.4 0.3 0.2 0.1 0.0 Initial Resistance vs. Air Velocity MERV A8 Performance Data Initial Resistance Recommended Final Resistance 0 100 200 300 400 500 600 700 Flow Rate (fpm) Efficiency Rating per ASHRAE 52.2: 2007 MERV 11 1 Efficiency Rating per ASHRAE 52.2: 2007 Appendix J 492 fpm (1968 cfm for 24 x 24 filter) 0.26±0.01 inches of water 1.4 inches of water MERV A8 Average Dust Holding Capacity at 1.4 inches of water 90±15g Resistance (inches of water) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 Resistance vs. Dust Loading @ 492 fpm 0 20 40 60 80 100 ASHRAE Dust Fed (g) Filter Measurements A B C Stock Nominal Dimensions Width A Height B Depth C E324 70-0712-4480-3 10 x 10 x 2 (254 x 254 x 51) 9 3/8 (238) 9 3/8 (238) 1 7/8 (48) E325 70-0712-4481-1 10 x 20 x 2 (254 x 508 x 51) 9 3/8 (238) 19 3/8 (492) 1 7/8 (48) E326 70-0712-4482-9 12 x 20 x 2 (305 x 508 x 51) 11 3/8 (289) 19 3/8 (492) 1 7/8 (48) E327 70-0712-4483-7 12 x 24 x 2 (305 x 610 x 51) 11 3/8 (289) 23 3/8 (594) 1 7/8 (48) E328 70-0712-4484-5 14 x 20 x 2 (356 x 508 x 51) 13 3/8 (340) 19 3/8 (492) 1 7/8 (48) E329 70-0712-4485-2 14 x 25 x 2 (356 x 635 x 51) 13 3/8 (340) 24 3/8 (619) 1 7/8 (48) E330 70-0712-4486-0 15 x 20 x 2 (381 x 508 x 51) 14 3/8 (365) 19 3/8 (492) 1 7/8 (48) E331 70-0712-4487-8 16 x 16 x 2 (406 x 406 x 51) 15 3/8 (391) 15 3/8 (391) 1 7/8 (48) E332 70-0712-4540-4 16 x 20 x 2 (406 x 508 x 51) 15 3/8 (391) 19 3/8 (492) 1 7/8 (48) E333 70-0712-4541-2 16 x 24 x 2 (406 x 610 x 51) 15 3/8 (391) 23 3/8 (594) 1 7/8 (48) E334 70-0712-4542-0 16 x 25 x 2 (406 x 635 x 51) 15 3/8 (391) 24 3/8 (619) 1 7/8 (48) E335 70-0712-4543-8 18 x 20 x 2 (457 x 508 x 51) 17 3/8 (441) 19 3/8 (492) 1 7/8 (48) E336 70-0712-4544-6 18 x 24 x 2 (457 x 610 x 51) 17 3/8 (441) 23 3/8 (594) 1 7/8 (48) E337 70-0712-4545-3 18 x 25 x 2 (457 x 634 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E338 70-0712-4546-1 20 x 20 x 2 (508 x 508 x 51) 19 3/8 (492) 19 3/8 (492) 1 7/8 (48) E339 70-0712-4547-9 20 x 24 x 2 (508 x 610 x 51) 19 3/8 (492) 23 3/8 (594) 1 7/8 (48) E340 70-0712-4548-7 20 x 25 x 2 (508 x 635 x 51) 19 3/8 (492) 24 3/8 (619) 1 7/8 (48) E341 70-0712-4549-5 20 x 30 x 2 (508 x 762 x 51) 19 3/8 (492) 29 3/8 (746) 1 7/8 (48) E342 70-0712-4550-3 24 x 24 x 2 (610 x 610 x 51) 23 3/8 (594) 23 3/8 (594) 1 7/8 (48) E343 70-0712-4551-1 25 x 25 x 2 (635 x 635 x 51) 24 3/8 (619) 24 3/8 (619) 1 7/8 (48)

High Air Flow (HAF) Filters Microstructured Features Airflow The open channel construction of 3M HAF filters offers low initial airflow resistance, while its unique microstructure and electrostatic charge provides effective particle capture and retention. In certain applications, this may translate into fewer filter changeouts, reduced coil cleaning, and reduced maintenance costs. A balanced approach to improved air filtration 3M HAF Air Filters may offer an ideal alternative in applications where regular filter replacement is difficult or impractical, but where low airflow resistance is important. Developed using innovative 3M technologies, 3M HAF Air Filters are frameless, selfsupporting, and are constructed from an array of open flow channels. These filters are electrostatically charged for enhanced particle capture and retention. 3M HAF Air Filters are available with an antimicrobial agent to help inhibit the growth of mold and mildew on the filter media. Users should be aware that mold and mildew may grow on captured particles that build up over time on the filter. Physical characteristics Open channel structure Microstructured, electrostatically charged media (refer to Performance Data on next page) 100% synthetic media Self-supporting filter Standard: White Antimicrobial: Green Filter Measurements Height A max Length B max Available Thicknesses C C 27.56 (700) 47.24 (1200) 0.20, 0.39, 0.59, 0.79, 0.98, 1.18 (5, 10, 15, 20, 25, 30) A B

Additional Information For questions or to place an order in the U.S., contact your local 3M Purification Inc. distributor or 3M Purification Inc. Customer Service at (800) 648-3550 or (651) 789-7381 IMPORTANT NOTICE: The information in this literature is based on tests 3M believes are reliable. It is not and should not be relied on as a product or technical specification. We do not guarantee the accuracy of this information. If any products described in this literature are defective, 3M will replace them at no charge. THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES FOR THESE PRODUCTS, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. You are responsible for determining whether products described in this literature are fit for a particular purpose and suitable for your application. Because there are many factors within your knowledge and control that might affect the use and performance of these products, you must evaluate these products to determine whether they are fit for a particular purpose, are suitable for your application, and meet your performance expectations. 3M IS NOT LIABLE FOR ANY LOSS OR DAMAGES, WHETHER DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL ARISING OUT OF THE USE OF OR INABILITY TO USE ANY OF THESE PRODUCTS. CAUTION: USED FILTERS MAY CONTAIN CONTAMINANTS FROM OPERATION OF THE HVAC SYSTEM. FOR PROPER HANDLING OF USED FILTERS, CONSULT APPLICABLE HEALTH AND SAFETY STANDARDS OR CONTACT AN INDUSTRIAL HYGIENIST. TO REDUCE RISK OF ILLNESS OR INJURY, ALWAYS USE APPROPRIATE RESPIRATORY PROTECTION AND PROTECTIVE CLOTHING WHEN REMOVING OR HANDLING USED FILTERS. DISPOSE OF USED FILTERS ONLY IN ACCORDANCE WITH FEDERAL, STATE AND LOCAL LAWS AND REGULATIONS. IMPORTANT USE RESTRICTIONS: DO NOT EXPOSE THIS FILTER DIRECTLY TO UV RADIATION FROM A UV PURIFICATION SYSTEM. EXCESSIVE UV EXPOSURE MAY LEAD TO A REDUCTION IN THE MECHANICAL INTEGRITY AND PERFORMANCE OF THE FILTER. THIS FILTER MUST NOT BE USED FOR THE FOLLOWING UNAUTHORIZED USES: A) ASBESTOS, LEAD OR MOLD REMEDIATION; B) BIOTERRORISM PROTECTION; C) APPLICATIONS IN BUILDINGS THAT REQUIRE OR ARE UNDERGOING AIR HANDLING SYSTEM REMEDIATION OF HAZARDOUS SUBSTANCES; OR (D) PROTECTIVE ENVIRONMENTS PER AIA GUIDELINES. 3M Purification Inc. 400 Research Parkway Meriden, CT 06450 U.S.A. (800) 648-3550 (651) 789-7381 www.3mpurification.com/airfilters 3M is a trademark of 3M Company. LEED is a trademark of the U.S. Green Building Council. 2014 3M Company. All rights reserved. Please recycle. Printed in U.S.A. 70020314087 REV 0514 Your Local Distributor: