Compact, rugged housing Many mounting possibilities Status displayed via LED Immune to electromagnetic interference 1024 pulses per revolution (default) 360, 512, 1000, 1024, 2048, 2500, 3600, 4096, parametr. via Easy-Teach Free parametrization of the pulse number in the range from 1 to 5000 via PACTware Position of z-track set via Easy-Teach Burst function, absolute angular position output incrementally per Easy- Teach pulse Type code Ident no. 1590910 Max. Rotational Speed 10,000 rpm Determined with standardized construction, with a steel shaft Ø 20 mm, L = 50 mm and reducer Ø 20 mm Starting torque shaft load (radial / axial) not applicable, because of contactless measuring principle Nominal distance 1.5 mm Measuring range 0 360 Repeatability ð 0.01 % of full scale Linearity deviation ð 0.05 % f.s. Temperature drift ð ± 0.003 % / K Ambient temperature -25 +85 C 10 30 VDC Male M12 x 1, 8-pin Push-pull A, B, Z, A (inverse), B (inverse) Wiring diagram Operating voltage 10 30VDC Residual ripple ð 10 % U ss Rated insulation voltage ð 0.5 kv Short-circuit protection yes/ cyclic Wire breakage / Reverse polarity protection yes/ yes (voltage supply) Output function 8-pin, Push-Pull/HTL Output Type incremental Resolution, incremental 1024 Pulse frequency max. 200 khz Signal level high min. U B - 2 V Signal level low max. 2.0 V Sample rate 1000 Hz Current consumption < 100 ma Dimensions 81 x 78 x 24 mm Shaft Type Hollow shaft Housing material metal/plastic, ZnAlCu1/PBT-GF30-V0 Connection male, M12 x 1 Vibration resistance 55 Hz (1 mm) Vibration resistance (EN 60068-2-6) 20 g; 10 3000 Hz; 50 cycles; 3 axes Shock resistance (EN 60068-2-27) 100 g; 11 ms ½ sinus; each 3x; 3 axes Continuous shock resistance (EN 60068-2-29) 40 g; 6 ms ½ sinus; each 4000 x; 3 axes IP Rating IP68 / IP69K MTTF 138 years acc. to SN 29500 (Ed. 99) 40 C Functional principle The measuring principle of inductive angle sensors is based on oscillation circuit coupling between the positioning element and the sensor, whereby an output signal is provided proportional to the angle of the positioning element. The rugged sensors are wear and maintenance-free, thanks to the contactless operating principle. They convince through their excellent repeatability, resolution and linearity within a broad temperature range. The innovative technology ensures a high immunity to electromagnetic DC and AC fields. Power-on indication Measuring range display Included in delivery LED green LED, yellow, yellow flashing MT-QR24 mounting aid 1 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
Extensive range of mounting accessories for easy adaptation to many different shaft diameters. Based on the functional principle of RLC coupling, the sensor operates absolutely wear-free and is immune to magnetized metal splinters and other interference fields. Wrong installation is hardly possible. The adjacent figure shows the two separate units, sensor and positioning element. Mounting option A: First, interconnect positioning element and rotatable shaft. Then place the encoder above the rotating part in such a way that you get a tight and protected unit. Mounting option B: Push the encoder on the back site of the shaft and fasten it to the machine. Then clamp the positioning element to the shaft with the bracket. Mounting option C: If the positioning element is to be screwed on a rotating machine part, use the RA0-QR24 plug which is included in the delivery. Then tie up the bracket. Screw on the encoder via the three bores. The separately arranged sensor and positioning element inhibit that compensating currents or damaging mechanical loads are transmitted via the shaft to the sensor. In addition, the encoder remains tight and highly protected during its entire lifespan. The accessories enclosed in the delivery help to mount encoder and positioning element at an optimal distance from each other. LEDs indicate the switching status. Status display via LED green steady: Optimal sensor supply yellow steady: Positioning element has reached the end of the measuring range. This is indicated by a lower signal quality. yellow flashing: Positioning element is outside the measuring range. off: Positioning element is in the measuring range. 2 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
Individual Parameterization (Teaching with Positioning Element) Jumper between teach input Gnd Pin 1 Ub Pin 2 LED Pin 8 2 s Z-track zero point teaching One-time triggering of burst function Status LED flashes then turns steady after 2 s 10 s CCW rotation direction CW rotation direction After 10 s status LED flashes fast for 2 s 15 s - Factory setting (z-track, CW) After 15 s power and status LED alternate To avoid unintended teaching, keep pin 8 potential-free. Preset Programming Mode (Teaching without Positioning Element) Jumper between teach input Gnd Pin 1 Ub Pin 2 LED Pin 8 2 s Resolution setting mode active for 10 s Resolution setting mode active for 10 s Status LED steady, flashes after 2 s as long as selection mode is active 360 pulses / 360 Start value 1 x flashing 512 pulses / 360 Press once 2 x flashing 1000 pulses / 360 Press twice 3 x flashing 1024 pulses / 360 Press three times 4 x flashing 2048 pulses / 360 Press four times 5 x flashing 2500 pulses / 360 Start value 1 x flashing 3600 pulses / 360 Press once 2 x flashing 4096 pulses / 360 Press twice 3 x flashing 5000 pulses / 360 Press three times 4 x flashing To avoid unintended teaching, keep pin 8 potential-free. 3 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
P1-Ri-QR24 1590921 Positioning element, for Ø 20 mm shafts P2-Ri-QR24 1590922 Positioning element, for Ø 14 mm shafts P3-Ri-QR24 1590923 Positioning element, for Ø 12 mm shafts P4-Ri-QR24 1590924 Positioning element, for Ø 10 mm shafts P5-Ri-QR24 1590925 Positioning element, for Ø 6 mm shafts 4 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
P6-Ri-QR24 1590926 Positioning element, for Ø 3/8 shafts P7-Ri-QR24 1590927 Positioning element, for Ø 1/4 shafts P9-Ri-QR24 1593012 Positioning element for installation on Ø 1/2 shafts P10-Ri-QR24 1593013 Positioning element for installation on Ø 5/8 shafts P11-Ri-QR24 1593014 Positioning element for installation on Ø 3/4 shafts 5 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
P8-Ri-QR24 1590916 Positioning element with blanking plug for large shafts M1-QR24 1590920 Aluminium protecting ring, for inductive encoders Ri-QR24 PE1-QR24 1590937 Positioning element without adapter sleeve RA1-QR24 1590928 Adapter sleeve, for Ø 20 mm shafts RA2-QR24 1590929 Adapter sleeve, for Ø 14 mm shafts 6 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
RA3-QR24 1590930 Adapter sleeve, for Ø 12 mm shafts RA4-QR24 1590931 Adapter sleeve, for Ø 10 mm shafts RA5-QR24 1590932 Adapter sleeve, for Ø 6 mm shafts RA6-QR24 1590933 Adapter sleeve, for Ø 3/8 shafts RA7-QR24 1590934 Adapter sleeve, for Ø 1/4 shafts 7 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
RA9-QR24 1590960 Adapter sleeve, for Ø 3/8 shafts RA10-QR24 1590961 Adapter sleeve, for Ø 3/8 shafts RA11-QR24 1590962 Adapter sleeve, for Ø 3/8 shafts RA8-QR24 1590959 Plug for positioning element (alternative to adapter sleeve) SP1-QR24 1590938 Shield Ø 74 mm, aluminium 8 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
SP2-QR24 1590939 Shield Ø 74 mm, aluminiuim, with borehole for shaft feedthrough SP3-QR24 1590958 Shield Ø 52 mm, aluminium MT-QR24 1590935 Mounting aid for optimal alignment of positioning element RKC8T-2/TXL 6625142 Connection cable, female M12, straight, 8-pin, cable length: 2 m, sheath material: PUR, black; culus approval; other cable lengths and qualities available, see www.turck.com TX2-Q20L60 6967117 Teach adapter for inductive encoders with 8-pin male M12 x 1, for simple programming via Easy Teach 9 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com
RKC8.302T-1,5-RSC4T/ TX320 6625003 Adapter cable to connect sensor to USB-2-IOL-0002 parametrizing unit; female M12, straight, 8-pin on male M12, straigth, 3-pin; cable length: 1.5 m; sheath material: PUR, sheath color: black, culus approved; RoHS conform; protection class IP67 10 / 10 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ more@turck.com ñ www.turck.com